itchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. PART LIST C. Middle Panel D. Middle Panel A. Side Panel B. Side Panel E1. Front Piece E2. Front Piece F. Back Piece G. Base P. Handle Arm H. Back Panel I. Back Stretcher J. Front Stretcher L. Side Rack O. Brush Chrome Pipes Front Rail M. Side Rack N. Base Rack Q. Round Arm R. Shelf S. Door T. Door U. D. Drawer V. D. Drawer (For Drawer U&V packed in separate carton with hardware and assembly instructions.) Hex Wrench 14 pcs. (+1 extra) Wood Plug 10 pcs. (+2 extra) nob Caster two lock two non-lock 4 pcs. Small Hex Wrench for Caster 16 pcs. (+2 extra) Adjustable Pin 8 pcs. (+2 extra) for nob Tools Required For Assembly : Phillips screwdriver Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319 servicedesk@homestyles-furniture.com
Assembly Instructions 2/3 IMPORTANT Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in the safe place as you may need to tighten up the s in the future. STEP 1 Attach four Casters underneath Base (G) with s. (See Arrow sticker indicating front side) STEP 2 Locking Caster (On Front) G Attach the Back Piece (F), Middle Panel (C) and Back Piece (F), Middle Panel (D) onto the Base (G). F F C D E1 G E2 A C STEP 3 Assemble Front Piece (E1), (E2) and Front Rail (). (See figure 1) D Attach the assembled unit to Middle Panel (C) and (D). Attach Side Panel (A) to the side of unit with s.
STEP 4 Slide Back Panel (H) into place. Attach Back and Front Stretcher (I), (J) to the unit with s. Assembly Instructions 3/3 I H J H H Attach Side Panel (B) to the other side of unit with s. B L N STEP 5 O A M STEP 6 Attach Handle Arm (P) to Side Panel (B) with s. Slide the Round Arm (Q) into place. Attach Side Rack (L) to Side Panel (A) with s. Attach Brush Chrome Pipes (O) and Base Rack (N) to the Side Rack (L). Attach Side Rack (M) to the Side Panel (A), using s. B P P Q R R STEP 7 Insert Adjustable Pins into both side panels and middle panels at the desired level. Place Shelf (R). Adjustable Pin STEP 8 Cover up all holes with Wood Plugs.
Drawer (U) UNIT PART LIST. Front Part for each U2. Back Part for each. for each. for each U5. Base Part for each Pull Handle for Pull Handle 6 pcs. (short) for base part 18 pcs.(+1 extra) (long) for side part 24 pcs.(+1 extra) Assembly Instructions Using a philips screwdriver, insert 1 screws into the pre-drilled holes as shown, tighten half way. (See the figure 1) U2 make sure roller is on the back Slide the Plywood Base Part (U5) into the grooves on s () and (). Be sure to push the plywood all the way forward so it meets the Front Part (). (See the figure 2) U5 (Figure 2) Unfinished Side U2 U5 Insert the remaining (6) 1/2 screws into the pre-drilled holes on Base Part (U5), then tighten all screws. (See the figure 3) (Figure 3) * If you are missing any of these parts, please contact our DMI Customer Service Department at 1-877-831-0319 or fax us at 1-800-755-2878. Assemble the Pull Handle with on the Front Part (). (See the figure 4) (Figure 4)
Drawer (V) UNIT PART LIST. Front Part... Pull Handle 1 pcs. (short) for base part 6 pcs.(+1 extra) V2. Back Part. V5. Base Part for Pull Handle (long) for side part 8 pcs.(+1 extra) Assembly Instructions Using a philips screwdriver, insert 1 screws into the pre-drilled holes as shown, tighten half way. (See the figure 1) V2 make sure roller is on the back Slide the Plywood Base Part (V5) into the grooves on s () and (). Be sure to push the plywood all the way forward so it meets the Front Part (). (See the figure 2) (Figure 2) Unfinished Side V5 (Figure 3) V2 V5 Insert the remaining (6) 1/2 screws into the pre-drilled holes on Base Part (V5), then tighten all screws (See the figure 3) * If you are missing any of these parts, please contact our DMI Customer Service Department at 1-877-831-0319 or fax us at 1-800-755-2878. Assemble the Pull Handle with on the Front Part (). (See the figure 4) (Figure 4)