Installation Instructions: Do This First (for existing sleeve) Note that the air conditioner dimensions are: "wide, 1 1 "high, and 18 1 "deep (without front). Install Air Conditioner according to these installation instructions to achieve the best performance. Save these installation instructions for future reference. Items in Kit You may not need all parts in the kit. Discard unused parts. Qty. Tapered Spacer Blocks 1"Long Centering/Support Blocks 1 "x 1 "x 1 1 " Plastic Divider 1/8 x 1 "x 1 1 " 1 Stuffer Seal 1"x 1 1 "x 8" 1 Seal 1 1 "x 1 1 "x 1 " Seal 1 1 "x 1 1 "x 1" Seal 1 1 "x /8"x 1 " Seal 1 1 "x /8"x 1" Seal 1 x /"x 1" 1 Trim Frame (side legs) Trim Frame (top & bottom legs) Ground Wire (green) 1 Nut for grounding screw 1 Grounding Screw 1 Grille (plastic) 1 Nuts (plastic) Screw w/washer How to Install 1. Identify the wall-sleeve brand for your installation, from the chart below. Brand Wall Sleeve Dimensions (inches) Width Height Depth White-Westinghouse } Frigidaire 1 1 1 1, 1 1 Carrier (F Series) or General Electric/ Hotpoint 1 8 1 8 Whirlpool 8 1 1 1 1 8 or Fedders/Emerson 1 1 or 19 Sears/Kenmore 1 8 18 8 Emerson/Fedders 1 1 Carrier (1S Series) 1 8 18 8 Friedrich 1 1 NOTE: All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner. CAUTION: When installation is complete, replacement unit MUSThave a rearward 1/ to /1 slope as shown. REAR. Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows: Clean interior (do not disturb seals). Wall sleeve must be securely fastened in wall before installing Air Conditioner. Drive more nails or screws through sleeve, into wall, if needed. Repair paint if needed.. If not existing, drill a /1"clearance hole for grounding screw through left side of wall sleeve, in a clear area about inches maximum (to suit) back from front edge of sleeve as shown below. Next attach ground wire inside sleeve, using grounding screw and nut. Pull loose end of ground wire out front of sleeve, and temporarily bend it down and around lower edge of sleeve. Wall sleeve to unit sleeve grounding. Prepare the wall sleeve for installation of the new unit per the following Brand instructions. #1 Emerson 1"Deep # Fedders 19 "Deep # Fedders or Friedrich 1 "Deep # General Electric/Hotpoint 1 8"Deep # Sears or Carrier (1S Series) 18 8"Deep # Whirlpool 1 1 8"Deep # Whirlpool "Deep #8 White-Westinghouse/Frigidaire/ 1"+ 1 1 "Deep Carrier (F Series) #9 White-Westinghouse/Frigidaire "Deep. Install new unit into wall sleeve.. To attach ground wire to the new unit, remove the screw from the left side front.. Assemble and install the Trim Frame (see instruction). Wall Sleeve 1" Part No. 0900091 (8-101) UNIT " Max. FRONT LEVEL /1" Hole
#1 Emerson 1"Deep 10-1/" 10 1 ". Attach (1) 1 1 "x /8"x 1 "long seal as shown in the illustration.. Attach the () 1 1 "x /8"x 1"long seals, to the inside of the louvered pane. Install the seals as shown in the illustration.. Cut the 1 1 "x /8"x 1 "long seal to 1"long, and attach it to the inside of the louvered panel as shown in the illustration. Attach the () 1 "x 1 "x 1 1 "Centering/Support Blocks, one on each side wall, to the inside of the sleeve with the Tappered End facing the opening. These () blocks should be locaed approximately in the center of the side walls. To attach the blocks remove the backing paper from the blocks. Do not touch adhesive on the blocks. Press the blocks firmly in place.. Install the new unit into the wall sleeve.. Attach the ground wire to the unit as shown.. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended. 8. Assemble and install the Trim Frame. (see Trim Frame)
Trim Frame Assembly The purpose of trim frame is to cover space between wall sleeve and replacement unit cabinet. Each frame is made of four parts: 1. To assemble trim frame, insert snaps of side legs into top and bottom legs.. To install trim frame to sleeves, slide frame over cabinet until it is flush with the wall sleeve. NOTE: Be sure to route the cord through the trim frame before placing the trim frame on the unit. 11
#9 White-Westinghouse or Frigidaire "Deep 1 1. If the wall sleeve does not have a rear grille or louvered panel, install the plastic grille panel from the kit. The plastic grille panel is mounted to the inside of the wall sleeve at the rear flanges. There are () plastic nuts in the flanges of the wall sleeve. If your sleeve is missing these nuts or they are damaged, replacement nuts and grille mounting screws are supplied with the kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of the rear flanges. Place the grille against the rear flanges and use the () washer screws to secure the grille to the sleeve. 9 1 ". Attach the () 1 "x 1 "x 1 1 "foam blocks to the inside of the wall sleeve as shown in the illustration.. Attach 1"x /"x 1"long seal to the inside of the grille panel.. Cut the 1/8"x 1 "x 1 1 "long plastic divider to 1"long. Slide the plastic divider in the slots of the () foam blocks.. Cut to fit (1) 1 1 "x 1 1 "x 1 "long seals as shown.. Attach () 1 1 "x 1 1 "x 1"long seals to 1 1 "install the seals as shown. Seals should be flush with front portion of the 1 "x 1 "x 1 1 "foam blocks which holds the plastic divider.. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown. 8. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended. 8 10 8 9. Assemble and install the Trim Frame. (see Trim Frame)
# Fedders 19 "Deep 10-1/" 10 1 " 1 " 1 ". Attach the () 1 "x 1 "x 1 1 "Centering/Support Blocks to the inside of the walls of the wall sleeve as illustrate with tapered end facing the opening of sleeve. These () blocks should be located approximately in the center of the side walls. To attach the blocks remove the backing paper from the blocks. Do not touch adhesive on the blocks. Press the blocks firmly in place.. Cut () 1"Tapered Spacer Blocks and install as shown in the illustration. The "portion to be placed in front of the rib on base and tapered end facing the back of the sleeve. 1" The remaining portion to be placed behind the rib. /" Cut Here Tapered Spacer Block. Attach (1) 1 1 "x 1 1 "x 1 "long seals and the () 1 1 "x 1 1 "x 1" long seals as shown in the illustration.. Cut (1) 1 1 'x 1 1 "x 1 "long seal to 1"and attach to inside of the louvered panel as shown in the illustration. " 1" Protection Paper Backing. Install the new unit into the wall sleeve.. Attach the ground wire to the unit as shown. 8. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended. 8 8 9. Assemble and install the Trim Frame. (see Trim Frame)
# Fedders or Friedrich 1 "Deep 10-1/" 1 " 1 " 10 1 ". Attach () 1 "x 1 "x 1 1 "Centering/Support Blocks to the inside of the walls of the wall sleeve as illustrated with tapered end facing the opening of the Sleeve. These () blocks should be located approximately in the center of the side walls. To attach the blocks remove the backing paper from the blocks. Do not touch adhesive on the blocks. Press the blocks firmly in place.. Cut () 1"Tapered Spacer Blocks and install as shown in the illustration. The "portion to be placed in front of the rib on base and tapered end facing the back of the sleeve. The remaining portion to be placed behind the rib. The 1 "portion to be placed in front of the rib on the base with the tapered end facing the back of the sleeve. Cut the remaining portion to 1 1 "and place behind the rib with the tapered end facing the back of the sleeve. 1" /" Tapered Spacer Block 1" Cut Here 1-1/" -1/" Protection Paper Backing. Attach (1) 1 1 "x 1 1 "x 1 "long seals and the () 1 1 "x 1 1 "x 1"long seals as shown in the illustration.. Cut (1) 1 1 "x 1 1 "x 1 "long seal to 1"and attach inside of the louvered panel as shown in the illustration.. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown.. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended. 8. Assemble and install the Trim Frame. (see Trim Frame)
#8 White-Westinghouse/Frigidaire/ 1"+ 1 1 "Deep Carrier (F Series) 1 9 1 1. If the wall sleeve does not have a rear grille or louvered panel, install the plastic grille panel from the kit. The plastic grille panel is mounted to the inside of the wall sleeve at the rear flanges. There are () plastic nuts in the flanges of the wall sleeve. If your sleeve is missing these nuts or they are damaged. Replacement nuts and grille mounting screws are supplied with the kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of the rear flanges. Place the grille against the rear flanges and use the () washer screws to secure the grille to the sleeve.. Cut and attach the (1) 1 1 "x /8"x 1 "long seal to 1 "long. Attach () 1 1 "x /8"x 1"long seals as shown. To attach the seals remove the backing paper from the seal. Do not touch adhesive. Press seals firmly in place.. Attach 1"x /"x 1"long seal to the inside of the grille panel as shown in the illustration.. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown.. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended.. Assemble and install the Trim Frame. (see Trim Frame) 9
# Whirlpool "Deep 10" 9-1/". Attach the () 1 "x 1 "x 1 1 "foam blocks to the inside top and bottom of the wall sleeve with the slots 10"from the right side wall of the sleeve. Attach () Tapered Spacer Blocks behind rib on inside bottom of the wall sleeve as shown. Taper towards the rear of the sleeve. 1" /" Tapered Spacer Block. Attach 1"x /"x 1"long seal to the inside of the grille panel. 10". Install the 1/8"x 1 "x 1"long plastic divider to the 1 1 "long. Slide the plastic divider in the slots of the () foam blocks. 1 " 1 " 1" 8". Cut to fit (1) 1 1 "x 1 1 "x 1 "long seals as shown. Attach () 1 1 "x 1 1 "x 1"long seals. Install the seals as shown. Seals should be flush with front side of 1 "x 1 "x 1 1 "Foam Blocks which holds the plastic divider.. Install the 1"x 1 1 'x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended.. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown. 8 9. Assemble and install the Trim Frame. (see Trim Frame)
# General Electric/Hotpoint 1 8"Deep 11" 10 1 10 1 ". Cut () 1"Tapered Spacer Blocks to 1 and install as shown in the illustration with the tapered end 1 "from the back of the sleeve. 1" /" Tapered Spacer Block 1" Cut Here 1" 1 " 1 " Protection Paper Backing. Cut (1) 1 1 "x /8"x 1 "long seals to "long attach as shown. Attach () 1 1 "x /8"x 1"long seals as shown in the illustration.. Attach 1"x /"x 1"long seal to the louvered panel as shown in the illustration.. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown.. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended.. Assemble and install the Trim Frame. (see Trim Frame)
# Sears or Carrier (1S Series) 18 8"Deep 10" 9-1/" 10". Attach () Tapered Spacer Blocks to the inside of the wall sleeve as shown in the illustration. DO NOT CUT THESE BLOCKS. 1" 1 " 1 ". Attach the (1) 1 1 "x /8"x 1 "long seals and the () 1 1 "x /8"x 1'long seals as shown in the illustration.. Attach the 1'x /"x 1"long seal to inside of the louvered panel as shown in the illustration. Install the new unit into the wall sleeve. /" Tapered Spacer Block 1" 1" Protection Paper Backing. Attach the ground wire to the unit as shown.. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended.. Assemble and install the Trim Frame. (see Trim Frame)
# Whirlpool 1 1 8"Deep 10" 9-1/" 10". Cut () Tapered Spacer Blocks and install as shown in the illustration. To attach the blocks remove the backing paper from the blocks. Do not touch adhesive on the blocks. Press the blocks firmly in place. 1" /" Tapered Spacer Block 1" 1 " 1 " Cut Here. Cut and attach the (1) 1 1 "x /8"x 1 "long seal to 1 "long. Attach the () 1 1 "x /8"x 1"long seals as shown.. Attach 1"x /"x 1"long seal to the louvered panel as shown in the illustration. 1" Protection Paper Backing. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown.. Install the 1"x 1 1 "x 8"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended. 8. Assemble and install the Trim Frame. (see Trim Frame)