12345 1
Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex cap machine screw ¼-20 x 5/8 long with 3/16 hex drive, black Used on spine beam mounts and cable trays Hex cap machine screw ¼-20 x 2 3/4 long with 3/16 hex drive, black Used on rails and legs Hex set screw ¼-28 x 1/4 long with 1/8 hex drive, silver Used on spine screens Pan head machine screw 10-24 x 5/8 long thread cutting tip with #2 Phillips drive, silver. Used to attach outlets. Pan head machine screw 8-32 x 3/8 long thread rolling tip with #2 Phillips drive, silver. Used to assemble electrical covers. Pan head machine screw 10-32 x 1/2 long with #2 Phillips drive, silver. Used on spine screens to attach base support brackets. Flat head machine screw 10-32 x 1/2 long with #2 Phillips drive, silver. Used on territory screens to attach base support brackets. Pan head machine screw 8-32 x 1/4 long with #2 Phillips drive, silver. Used with acorn nuts to attach powerpole. Acorn nut 8-32 x 5/16 long, silver. Used with 8-32 x ¼ long screws to attach powerpole. Pan head drill point sheet metal screw #8 x 3/8ths long with #2 Phillips drive, silver. Used to attach Side Mount screens to hanging brackets and endcap worksurface cantilevers to legs. Flat head sheet metal screw #8 x 2 long with #2 Phillips drive, silver. Used to mount Endcap Hutch to base. Flat head sheet metal screw #10 x 3/4 long with #2 Phillips drive, silver. Used to mount items to laminate storage cabinets. Flat head self drilling screw #10 x 3/4 long with #2 Phillips drive, stainless steel. Used to mount screens. 2
Revision Log 12345 Date Page No. Description of change Name 12-9-16 39, 3, 2 Pg. 39: #10x3/4 flat screw was #8x3/8 pan screw Pg. 2: Added #10x3/4 flat head self drilling screw Pg. 3: Added Revision Log 12-28-16 30,32-36 Pg. 30 and 34: Updated images of brackets Pg. 31-33: New pages detailing glass screen installation Pg 34 and 35 (Screen Installation pages): Was page 31 and 32. Moved order to end of Screen Assembly S. Powers S. Powers 3
Straight Leg Assembly ¼-20 x 2.75L hex cap screw and nut 6 places. Tighten fully. End Leg Assembly 12345 Note: Place screw heads on OUTSIDE of bench. Spine Beam Mount Twist Plate ¼-20 x 5/8 L hex cap screw 2 places. Leave loose. Rail Mount Leg Horizontal Insert leg to stops Note: Tighten set screw until metal forks are spread outward into tube sides. Joint should have no movement. ½-13 x 2 L Set Screw. 2 places. 4
Shared Leg Assembly 12345 End Leg Assembly (See page 3) Shared Leg Assembly Mirror parts on End Leg Assembly Note: Use the same ¼-20 x 2.75L Hex Cap Bolt and Nut to hold on both parts. 5
¼-20 x 2.75L hex cap screw and nut 2 places. Tighten fully. Note: Place screw heads on OUTSIDE of bench. Single Sided Bench 12345 Leg Assembly Single bench leg horizontal 24 or 30. Rail Mount LEFT END SINGLE BENCH LEG ASSEMBLY ¼-20 x 2.75L hex cap screw and nut 2 places. Tighten fully. Note, Rail Mount will straddle leg attachment set screw. Single Bench Spine Beam Support Left 6
Single Sided Bench 12345 Leg Assemblies Single Bench Spine Beam Support Right Single Bench Spine Beam Support Left Shared Leg (mirror components) End Leg Right End Leg Left 7
Outlet port locations Outlet & Powerway 12345 Cover Installation 48w 96w Powered Spine Beam Assembly (Shown on floor upside down) 10-24 x 5/8 Pan Head Machine Screw with thread cutting tip, 1 per outlet in bottom hole Outlet port locations Insert numbered outlets per plan, engaging left or right as shown. Then screw outlets to powerway to secure. Pan head machine screw 8-32 x 3/8 long thread rolling tip 8 places Note: Overlap flanges such that small holes are behind big holes. Note: 36w and 42w powered assemblies accommodate 2 outlets only 8
Center wire basket left to right on spine beam. Wire Basket Installation 12345 Twist plate ¼-20 x 5/8 L hex cap screw 4 places. Tighten fully. Note: Wire baskets for 36w and 42w spine beams are made up of (2) 12 sections or (2) 15 sections, mounted as shown. 36w and 42w spine beam assembly 48w - 96w spine beam assembly 9
Install Rear Supports on rail width 60 96, depths 24 and 30. Worksurface Rail 12345 Assembly Rear Support Front Cantilever Install Front Cantilevers on rails sizes 60w 96w, 30 DEEP ONLY Rail ¼-20 x 2.75L hex cap screw and nut 2 places. Tighten fully. 10
Spine Assembly 12345 Twist Plate Slide rail assemblies to align with twist plate holes ¼-20 x 5/8 L hex cap screw 4 places. Tighten fully. Double Bench Single Bench Note: Single Benches have one spine beam assembly and one rail assembly only. 11
Beam end 2 inches from crossbar Double Bench Assembly 12345 Shared leg End condition holes (pair closer to leg) End Leg ¼-20 x 2.75L hex cap screw and nut 8 places. Tighten fully. Twist Plate Shared condition holes (pair farther from leg) Beam end at center of crossbar View from below ¼-20 x 5/8 L hex cap screw 4 places. Tighten fully. Spine Beam Mount End Leg Shared legs End Leg 12
Single Bench Spine Assembly Single Bench Assembly 12345 Single Sided Bench End Right Leg Single Sided Bench End Left Leg Single Sided Bench Shared Leg ¼-20 x 2.75L hex cap screw and nut 4 places. Tighten fully. View from below right Twist plate ¼-20 x 5/8 L hex cap screw 4 places. Tighten fully. 13
Jumper Installation 12345 Locking clip on powerway MUST be present and engaged behind wedges on jumper. 14
Worksurface is always centered on spine beams C L Bench Top Installation 12345 Center of leg plate Important: This spacing varies between leg type. DO NOT use for top placement. Always center top on spine beam as indicated. Metal tab prevents surface from touching spine beam to facilitate clamp on elements. 2 places 2 places 4 places #9 x 7/8ths flat head Phillips 2 places 15
Access Box Trim Ring Access Box Door 12345 Installation Rubber gaskets on short sides indicates BACK Rubber gaskets on long side indicates FRONT View from below surface Access Box Retainer 8-32 x.75l Thread Cutting Flat Head Phillips 4 Places Seat Door Slot ON rubber gasket Access Box Cover 16
Access Box Base 12345 Installation Center box left to right, align front edge with front edge of access hole #9 x 7/8ths flat head Phillips 4 places Single Gang Adapter Single Gang Device Plate Data Jacks 6-32 Machine Screw Snake data cables through either left or right access hole in box base Snap adapter into hole in box base. 17
Laminate Ends 12345 Install Double Bench End Panel Single Bench Shared Leg Double Bench Shared Leg Mid Run End Panel Right Single Bench End Panel Right Full Height Modesty Right end 36 72 bench Right end 78 96 bench Left end 36-72 bench Left end 78-96 bench Mid end right 36 72 bench Mid end right 78 96 bench Mid end left 36-72 bench Mid end left 78-96 bench 18
Predrills Double End 12345 Panel Assembly #9 x 7/8ths flat head Phillips 14 places ¼-20 x 5/8 inch Hex Cap screw 2 places Right Side Left Side Align UPPER RIGHT and LOWER LEFT bracket holes with pre-drilled holes on EP Align UPPER LEFT and LOWER RIGHT bracket holes with pre-drilled holes on EP #9 x 7/8ths flat head Phillips 6 places 19
Single End Panel 12345 Mid Run End Panel Assembly #9 x 7/8ths flat head Phillips 6 places #9 x 7/8ths flat head Phillips 6 places #9 x 7/8ths flat head Phillips 4 places 20
End Panel 12345 Bracket Alignment Rail placement for 60/30 deep legs Rail Placement for 48/24 deep legs Rail placement for 18/36 deep legs Double End Panel Single End Panel Mid Run End Panel 21
Double End Panel 12345 Install Center on beam ¼-20 x 5/16 Hex Cap Screw 8 places 22
Mid Run End 12345 Panel Install ¼-20 x 5/8 inch Hex Cap Bolt Mid Run End Panel Left 23
Single End Panel 12345 Install Single Sided Spine Beam Single Shared Leg Single End Panel Right Hand 24
Full Modesty 12345 Panel Install Full height modesty panel #9 x 7/8 Flat Head 10 places #9 x 7/8 Flat Head 6 places 25
Bench Top Install 12345 On Laminate Ends Install outlets, jumpers, electrical covers, cable tray per previous instructions. Align tops with end panel #9 x 7/8 inch Flat Head 8 places #9 x 7/8 inch Flat Head 4 places 26
Glass Spine Screen 12345 Clear Polycarbonate 2 Compression Strip (Insert between Glass and Set Screw) Glass ¼-28 x 1/4th Set Screws 4 places Page Revised 10-9-14 27
Fabric Spine Screen 12345 #10-32 x 3/8 th Pan Head Phillips 4 places ¼-28 x 5/16 th Set Screws 4 places 28
Spine Beam Covers 12345 Spine Beam Cover 29
Territory Screen 12345 Assembly Center Screen Assembly #10-32 x.5 inch Flat Head Machine Screw 4 Places Handed Screen Assembly (Right Hand Shown) #10-32 x.5 inch Flat Head Machine Screw 4 Places 30
Center Glass Screen Rail Assembly Glass Territory 12345 Screen Assembly Bracket #OX-SLSCBM Bracket #OX-SLSCFM #10-32 x 5/16 Flat Head Machine Screw 4 Places Handed Glass Screen Rail Assembly (Right Hand Shown) Screw must not protrude beyond inner rail surface Bracket #OX-SLSBML Bracket #OX-SLSFMR #10-32 x 5/16 Flat Head Machine Screw 4 Places 31
Glass Territory 12345 Screen Assembly Glass Territory Screen Installation Insert polycarbonate spacers (3 places) down in between glass screen and rail so that the spacer is located on the side directly behind the set screw holes. Install set screws (3 places), tightening to polycarbonate spacers. Check to insure set screw is not touching the glass surface and is flush or below the rail surface. (see image below) Glass screen should be secure to rail with no wobble. Flush surface required Polycarbonate Spacer 3 places Set Screw ¼-28 x ¼ 3 places 32
End Cap Installation Tap gently using soft mallet until end cap is properly seated. DO NOT break tabs. Glass Territory 12345 Screen Assembly End Cap (2 places) Rail Cover Installation Snap rail cover down onto rail from above using block of wood with soft mallet. If necessary, shave excess paint on tabs to insure end cap is properly seated. Rail Cover Insure Rail Cover is properly seated 33
Center Mount Screen 12345 Install (same for glass or framed) Bracket #OX-SLSBMB (2 places) ¼-20 x 5/16 inch Hex Cap screw 4 Places #9 x 7/8 inch Flat Head 6 Places 34
Left or Right Screen 12345 Install (same for glass or framed) ¼-20 x 5/16 inch Hex Cap Screw 2 Places #9 x 7/8 inch Flat Head 4 Places 35
End Leg Cover 12345 #9 Flathead Phillips 7/8 th long 4 Places Revision 12-28-16 36
Double Bench 12345 Power Pole Installation Do not install beam endcap Flush with bench top Align edge with back of bench top #9 flathead Phillips 7/8 th long 6 Places Plumb pole, rest bottom on floor 8-32 x ¼ inch pan head machine screws and acorn nuts 6 places Revision 12-28-16 37
Single Bench 12345 Power Pole Installation 8-32 x ¼ inch pan head machine screws and acorn nuts 3 places #9 flathead Phillips 7/8 th long 5 Places 38
Power pole coupler 12345 and cover #8-32 x 3/8 inch pan head Phillips thread rolling screw 4 places 39
Base Feed Vertical 12345 Wire Manager 3/8-16 Panel Glide and Carpet Gripper Floor Junction Box Level Wire Manager Wire Manager Cover 4 inch Wire Tie 6 base feed hardwired by electrician to floor box Locking clip on powerway MUST be present and engaged behind wedges on jumper. 40
#9 flathead Phillips 7/8 th L 16 Places Return Support 12345 Rail and Return Surface Worksurface Flatplates Rail Assembly Return Support Bracket 3/8-16 x ½ inch set screw 2 places Hex cap head ¼-20 x 5/16 inch long 4 places Use set screws To clamp to main worksurface rail assembly #9 flathead Phillips 7/8 th long 4 Places Return Support Endcap #9 flathead Phillips 7/8 th long 4 Places 41
Side Mounted 12345 Screens Side mount screens can be installed at varying heights. Consult with customer or workstation designer for proper placement. #10 x 3/4 flat head self drilling screw, phillips drive #2. Screw through fabric or whiteboard material into aluminum frame behind. Take care not to pull fabric on screen face. Screws will mar surface. Brackets cannot be moved after holes are drilled. Measure carefully from top to each bracket to assure even installation. Align brackets with inside edge of screen frame #9 flathead Phillips 7/8 th long 4 Places 42
Endcap Worksurface 12345 Endcap Cantilever Left Hand Endcap Cantilever Right Hand Outside location Reuse from leg assembly Hex cap head ¼-20 x 5/16 inch long 4 places 6 inches Center Line 6 inches Inside location #8 x 3/8ths pan head drill point sheet metal screw 4 places #9 flathead Phillips 7/8 th long 12 Places 43
Endcap Worksurface (No Holes) Do not use here Endcap Hutch Installation Facing Aisle 12345 Endcap Hutch Worksurface (6 holes with counterbores on bottom) Install like Endcap Worksurface. See Previous page Align WS holes with holes in Endcap Hutch Installation Facing Bench #8 x 2 inch Flat Head Phillips Screw 6 places Counter-bores face down/bottom 44
Desktop Storage 12345 Supports #10 x 3/4 inch LONG Flat Head Phillips Screw 6 places. DO NOT USE WORKSURFACE SCREWS. Width Center and affix High Friction Rubber Pads to bottom of support feet 4 places 16 inch deep storage units have 10 inch deep supports. 24 inch deep units have 20 inch deep supports. Width/4 2 Width/4 Less 1 1/8th Revision date 12-9-16 45