PB-735 HD DP Automtic punch nd bind mchine for books nd clendrs A further step for the utomtion of double loop binding. A clever nd flexible mchine ble to punch nd bind in line up to 9/16. Using the best of Rilecrt technology, compct nd user friendly, this mchine is the perfect solution when in need to replce semiutomtic mchinery with no risk of n underutilized investment. www.rilecrt.it
PB 735 HD DP Double-ction punching tool. Automtic punch nd bind mchine for books nd clendrs Division system BINDING SYSTEM HOW IT WORKS Clendrs nd books hve to be put on the mchine lredy collected. Then, depending on the thickness of the product the mchine cn be used in three wys: 1) Thickness less thn 4.: the mchine in this cse works in line without nything else to do, simply hve to pick up the product bound on the conveyor. 2) Thickness from 4. to 8.: it is necessry to use the seprting blde nd split the product in two booklets tht will be punched seprtely by the double-ction punching tool. 3) Thickness from 8. to 11.: more over the mximum punching limit of the mchine. It is necessry to split the book in two prts nd thn it will be utomticlly ressembled nd bound. The PB-735 HD DP cn be connected to gthering mchines. FEATURES The Compny reserves itself the right to modify the fetures of the products shown in this ctlogue. TECHNICAL SPECIFICATIONS 400 V 3-phse 50/60 Hz + Neutrl; Kw 7 6 Atm 30 mc/hour H 1100 x D 2000 x L 4500 2100 Kg PITCH DIAMETER DIAMETER 4:1 Ø inch Ø 1/4 6,3 1/4 6,3 5/16 7,9 3:1 3/8 9,5 7/16 11 1/2 12,7 9/16 14,3 BIND THICK 4,8 Uses wires on spools. Mximum binding size: for products up to 4. thickness: 350 x 500. for products over 4. thickness: 350 x 300. Minimum binding size: 100 x 100. Mximum punching thickness per stoke: 8. (4 + 4. depending on pitch, mterils nd width of the product). Stndrd binding dimeters: 1/4 (on request 5/16, 3/8, 7/16, 1/2 nd 9/16 ). Stndrd pitch 3:1 (on request 4:1 or 2:1 ). Speed vrible 500 to 2300 pieces/hour depending on size, thickness nd qulity of mterils. Cn be progred for continuous binding, two pieces with hnger or skip-binding. Centrl utomtic lubrifiction. OPTIONALS Automtic device for hngers from 100. to 200. Option for utomtic hnger feeder with hnger former. b Ø xb Ø 3,3x2,5 3 2 4,8 6,3 8 4x3 4x3,7 3,5 4 9,5 10,5 11,5 4x5 5 2 3 4 RILECART - WIREBIND INTERNATIONAL Hedqurters nd Fctory: Vi Dniele Pesenti, n 1 24022 Alzno Lombrdo - Bergmo Tel. +39 035 515.900 - Fx +39 035 515.060 E-mil: info@rilecrt.com - Internet: www.rilecrt.com
PB-796 HD ES Automtic punch nd bind mchine for clendrs The pride of our industril line. Seeing is believing, tht s wht we sy when people re sking us bout its performnces. Very simple nd esy to use our PB-796 HD ES is renowned worldwide for its relibility nd low mintennce costs. Equipped with the new punching tools Esy Setting type. www.rilecrt.it
PB-796 HD ES The Compny reserves itself the right to modify the fetures of the products shown in this ctlogue. Punching tool ES. Automtic punch nd bind mchine for clendrs The PB-796 HD ES working with utomtic 70. hnger feeder. BINDING SYSTEM HOW IT WORKS Clendrs hve simply to be plced onto the mchine nd collected t the end of the binding process. The mchine punches the complete clendr in one stroke, then hngers nd wire re inserted before everything is crried to the closing section to be bound. All this is done utomticlly. All punch pins re disconnectbles from the front without tking out the tools from the mchine, simply unscrewing screw. The djusting squre system hs been modified, reducing the chnge over times. Up to 50% reduction in pper size chnge over using the sme wire dimeter, up to 25% reduction in complete chnge over of punching nd binding size. FEATURES Using wires on spools. Mximum binding size: 600 x 700. Minimum binding size: 120 x 100. Mximum punching thickness per stroke is 4,5. (depending on pitch, mterils nd width of clendrs). Stndrd binding dimeters: 1/4 (on request 3/16, 5/16 nd 3/8 ). Stndrd pitch 3:1 (on request 4:1 ). Speed vrible 500 to 2300 pieces/hour depending on size, thickness nd qulity of mterils. Cn be progred for continous binding, two pieces of wire with hnger or skip binding. Cn be connected to ny kind of colltor. OPTIONALS 3/16, 5/16 nd 3/8 size tool sets. Additionl utomtic feeder for 70. hngers (for clendrs with two hngers). Automtic device for hngers from 100 to 450. or for 100 to 300. Feeder for hngers on reels. Punching tool for bck perfortion. Hnger former for 100-300. nd 100-450. hngers. TECHNICAL SPECIFICATIONS 400 V 3-phse 50/60 Hz + Neutrl; 9Kw 6 Atm - 10 mc/hour H 1300 x D 2400 x L 4500. 2400 Kg PITCH DIAMETER DIAMETER 4:1 3:1 Ø inch Ø 3/16 4,7 1/4 6,3 3/16 4,7 1/4 6,3 5/16 7,9 3/8 9,5 BIND THICK 3,5 4,8 3,5 4,8 6,3 8 xb b Ø Ø 3,3x2,5 3 4x3 3,5 4x3,7 4 2 2 3 RILECART - WIREBIND INTERNATIONAL Hedqurters nd Fctory: Vi Dniele Pesenti, n 1 24022 Alzno Lombrdo - Bergmo Tel. +39 035 515.900 - Fx +39 035 515.060 E-mil: info@rilecrt.com - Internet: www.rilecrt.com
PB-799 Automtic lrge formt clendr mchine Specilly designed for lrge formts our PB-799 cn lso be used to bind two clendrs time. Its high production speed mkes the perfect mchine for clendrs specilists. www.rilecrt.it
PB-799 Automtic lrge formt clendr mchine HOW IT WORKS Clendrs hve simply to be plced on to the mchine nd collected t the end of the binding process. The mchine punches the complete clendr in one stroke, then hngers nd wire re inserted before everything is crried to the closing section to be bound. All this is done utomticlly. FEATURES The Compny reserves itself the right to modify the fetures of the products shown in this ctlogue. Crrying system on the PB-799. Punching re. Double utomtic hnger feeder. BINDING SYSTEM PITCH DIAMETER DIAMETER 4:1 3:1 Ø inch Ø 3/16 4,7 1/4 6,3 3/16 4,7 1/4 6,3 5/16 7,9 3/8 9,5 BIND THICK 3,5 4,8 3,5 4,8 6,3 8 Uses wires on spools. Mximum binding size: 800 x 1000. Minimum binding size: 120 x 100. Possibility to punch nd bind two clendrs of mximum binding size 350. in one time. Possibility to pply one semiutomtic hnger feeder for 100-500. hngers or two semiutomtic hnger feeder for 100-200. hngers. Mximum punching thickness per stroke is 4,5. (depending on pitch, mterils nd size of the clendrs). Stndrd punching tool with 3,7 x 4. holes. Stndrd binding dimeters: 1/4 (on request 3/16,5/16 nd 3/8 ). Stndrd pitch 3:1 (on request 4:1 ). Mx. speed when processing one 800. clendrs: from 500 to 1400 pieces/hour depending on thickness nd qulity of mterils. Mx. production when processing two 350. clendrs: 2500 pieces/hour depending on thickness nd qulity of mterils. Cn be progred for continuous binding, two pieces with hnger or skip-binding. Cn be connected to ny kind of colltor. OPTIONALS 3/16, 5/16 nd 3/8 size tool sets. Hnger former option. TECHNICAL SPECIFICATIONS 400 V 3-phse 50/60 Hz + Neutrl; 10Kw 6 Atm - 30 mc/hour H 1700 x D 3000 x L 6000. 2800 Kg xb b ø Ø 3,3x2,5 3 4x3 3,5 4x3,7 4 2 2 3 RILECART - WIREBIND INTERNATIONAL Hedqurters nd Fctory: Vi Dniele Pesenti, n 1 24022 Alzno Lombrdo - Bergmo Tel. +39 035 515.900 - Fx +39 035 515.060 E-mil: info@rilecrt.com - Internet: www.rilecrt.com
B-535 T.S. Fully utomtic bookbinding mchine The new Rilecrt smll utomtic bookbinding mchine. Reduced size, reduced price, incresed productivity nd speed. Idel to nswer to the modern requests of print finishers nd sttionery mnufctures. Perfect to upgrde the lbour-intensive semiutomtic solutions. Thnks to its low cost, high productivity, simplicity, will ieditely py bck. Equipped with the new touch screen control system. www.rilecrt.it
B-535 T.S. Fully utomtic bookbinding mchine The wire out of tunnel reches the binding re. The B-535 T.S. nd Esy Lift unwinder. Wire feeding system. HOW IT WORKS The mchine is mnully fed with pre-punched nd gthered products with the covers on the bottom nd the punched side downwrds. The book is trnsported in the insertion re where it meets digonl br on which the spirl slides nd is cut. The first ring of the spirl slips into the first hole of the book, nd the ctul movement of the book itself fcilittes the insertion of the whole cut length. The spirl is then turned 90 in specil ptented tunnel nd finlly closed under specific pressing unit. This binding system is recognized s the simplest nd most nturl, due to the wy pper is hndled, llowing considerble speeds nd simplicity even throughout the chnging opertions nd ssocited fine tunings. FEATURES Uses wires on spools with dimeters from 1/4 to 1-1/4 for mximum binding thickness of 28. (Check thickness reference tble for detils). Mximum binding size: 320 x 300. Minimum binding size: 100 x 80. Specific tools for ech closing dimeter. Mx. speed: up to 2500 cycles per hour. Actul speed ccording to the product s technicl chrcteristics nd work orgnistion. Motorized single spool unwinder to reduce spce engged. Progred binding with on one piece of wire or skip up to five wire pieces. The Compny reserves itself the right to modify the fetures of the products shown in this ctlogue. Ø inch BINDING SYSTEM PTCH DIAMETER BIND THICK 1/4 4,5 5/16 6,5 3:1 3/8 8,5 7/16 10 1/2 11,5 9/16 12,5 9/16 12,5 5/8 14 2:1 3/4 17 7/8 20 1 23 1-1/4 28 TECHNICAL SPECIFICATIONS 400 V 3-phse 50/60 Hz + Neutrl; 3,5Kw 8 Atm - 5mc/hour H 1600 x D 1400 x L 4000. 1050 Kg OPTIONALS Size tool sets: 1/4 to 1-1/4. b Ø c xb Ø c 4x3,7 4 3 4x5 5 4 5x4,7 6 6x6 7 4 5 RILECART - WIREBIND INTERNATIONAL Hedqurters nd Fctory: Vi Dniele Pesenti, n 1 24022 Alzno Lombrdo - Bergmo Tel. +39 035 515.900 - Fx +39 035 515.060 E-mil: info@rilecrt.com - Internet: www.rilecrt.com
B-599 HF Fully utomtic book binding mchine The fstest fully utomtic binding mchine on the mrket. Cn process books, pds, exercise books, diries nd mny other products with double loop wire. Thnks to its wire rottion tunnel the pper is crried in the simplest wy ever nd this technology together with the prticulr wire feeding system llows the B-599 HF to chieve very high productivity. The mchine could be equipped with hnger feeder integrted with its hnger former. www.rilecrt.it
B-599 HF Fully utomtic book binding mchine The B-599 HF nd the Twin spool unwinder. Hngers-former nd feeder. HOW IT WORKS When the B-599 HF is not connected to the punching sttion (see DP-4500 line), it is necessry to feed the mchine with pre-punched products lredy gthered. The item put on the mchine is crried to the inserting re where joins the feeding device tht, thnks to sensor nd helped by the crrying movements, fits the wire into the holes. The wire then mkes 90 turn in specil ptented shped tunnel tht let the loops lie in the right position redy to be closed under proper binding tool. This system is recognized s the simplest ever, this gurntees high speed nd productivity. It cn bind wll clendrs with 1/4", 5/16 nd 3/8 wires with hngers from 100 to 200. Wire feeding system. FEATURES Uses wires on spools. For ll 3:1 nd 2:1 pitch from 1/4 to 1. Mximum binding size: 450 x 500. Minimum binding size: 100 x 80. Dedicted tools for ech dimeter. Productivity: 4000 pieces/hour. Effective speed depending on the item to be bound nd on production orgniztion. Double unwinder system for minimum chnge over time. Progred for one length or skip-binding up to five lengths. The Compny reserves itself the right to modify the fetures of the products shown in this ctlogue. Ø inch BINDING SYSTEM PITCH DIAMETER BIND THICK 1/4 4,5 5/16 6,5 3:1 3/8 8,5 7/16 10 1/2 11,5 9/16 12,5 9/16 12,5 5/8 14 2:1 3/4 17 7/8 20 1 23 TECHNICAL SPECIFICATIONS 400 V 3-phse 50/60 Hz + Neutrl; 5Kw 8 Atm - 5mc/hour H 1600 x D 1400 x L 4500. 1250 Kg OPTIONALS Size tool sets: 1/4" to 1. b Ø c xb Ø c 4x3,7 4 3 4x5 5 4 5x4,7 6 6x6 7 4 5 RILECART - WIREBIND INTERNATIONAL Hedqurters nd Fctory: Vi Dniele Pesenti, n 1 24022 Alzno Lombrdo - Bergmo Tel. +39 035 515.900 - Fx +39 035 515.060 E-mil: info@rilecrt.com - Internet: www.rilecrt.com
DP-4500 Fully utomtic punching nd binding mchine The top of the rnge of Rilecrt mchines. Thnks to its design nd its wire insertion system, the mchine combines flexibility, verstility nd relibility. Cn punch nd bind in line with double loop wire books, pds, exercise books, diries nd mny other items. www.rilecrt.it
DP-4500 Fully utomtic punching nd binding mchine Double punching re in the DP-4500. Wire feeding system. The DP-4500 dividing the book. Twin spool unwinder. HOW IT WORKS The line is composed by the utomtic double-side punching mchine DP-400 in line with the utomtic binding mchine B-599 HF. The punching unit, using of set of bldes, divides the item in booklets of 5. first, then in 2,5. nd punch them seprtely thnks to double (superior nd inferior) punching tool. The mchine then gthers the booklets nd brings the book to the closing unit where is utomticlly bound. The two mchines cn work together or, when required, off line. FEATURES Uses wires on spools. For ll 3:1 nd 2:1 pitch from 1/4 to 1. Binding size: Mx = 400 x 300., Min = 100 x 100. Dividing thickness: Mx: 5., Min: 3. Punching thickness: Mx: 5. per stroke. Dedicted tools for ech dimeter. Mx productivity: from 500 to 3000 pieces/hour ccording to the thickness of the product: 3-5. 5-10. 10-15. 15-20. 20-25. (1 booklet) (2 booklets) (3 booklets) (4 booklets) (5 booklets) = 3000 pcs/h = 1500 pcs/h = 1000 pcs/h = 750 pcs/h = 600 pcs/h Effective speed depends on the technicl fetures of the item nd on production orgniztion. The speeds shown re relted to pper of weight not less of 80 gr./sqm. The Compny reserves itself the right to modify the fetures of the products shown in this ctlogue. Ø inch BINDING SYSTEM PITCH DIAMETER BIND THICK 1/4 4,5 5/16 6,5 3:1 3/8 8,5 7/16 10 1/2 11,5 9/16 12,5 9/16 12,5 5/8 14 2:1 3/4 17 7/8 20 1 23 TECHNICAL SPECIFICATIONS 400 V 3-phse 50/60 Hz + Neutrl; 12Kw 8 Atm - 10 mc/hour H 9500 x D 3600 x L 2000. 3500 Kg OPTIONALS Size tool sets: 1/4 to 1. Additionl punching tool. b Ø c xb Ø c 4x3,7 4 3 4x5 5 4 5x4,7 6 6x6 7 4 5 RILECART - WIREBIND INTERNATIONAL Hedqurters nd Fctory: Vi Dniele Pesenti, n 1 24022 Alzno Lombrdo - Bergmo Tel. +39 035 515.900 - Fx +39 035 515.060 E-mil: info@rilecrt.com - Internet: www.rilecrt.com