RMMING MNUL MTM/01 MTMV/01 FB00329-EN
Generl precutions Red the instructions crefully efore eginning the instlltion nd crry out the ctions s specified y the mnufcturer. The instlltion, progrmming, commissioning nd mintennce of the product must only e crried out y qulified technicins, properly trined in complince with the regultions in force, including helth nd sfety mesures nd the disposl of pckging. Before crrying out ny clening or mintennce opertion, disconnect the device from the power supply. The equipment must e destined solely for the use for which it ws expressly designed. The mnufcturer declines ll liility for ny dmge s result of improper, incorrect or unresonle use. OPERTIONS FOR REMOTE CONTROL OF CLL BUTTONS Mnul configurtion of terminls nd s cll inputs 1 nd 2 Short circuit the terminls ( nd ), press nd hold the two cll uttons on the unit, nd power the device. The unit restrts. The procedure hs een completed successfully. Remove the short circuit nd connect the dditionl N.O. uttons to the terminls nd. BUTTON NUMBERING 1 3 5 7 2 1 4 2 1 6 3 2 1 8 4 3 2 1 2 1 Pge 2 - Mnul FB00329-EN - vers. 1-05/2016- Cme S.p.. - The contents of the mnul re to e considered s suject to chnge t ny time nd without the need for ny dvnce wrning.
RMMING ENTRY PNELS WITHOUT V/01 OR /01 Progrmming for the first time Entering progrmming mode Pge 3 - Mnul FB00329-EN - vers. 1-05/2016- Cme S.p.. - The contents of the mnul re to e considered s suject to chnge t ny time nd without the need for ny dvnce wrning. Press the utton on the entry pnel for t lest 3 seconds nd relese within 6 seconds. nd nd the utton LEDs flsh to show the uttons re eing prothe LEDs grmmed B. >3 <6 B C Progrmming uttons D Press the first cll utton on ech unit C or D. The unit stops flshing nd remins on. Repet for ll the other cll devices. NOTE. For the sic unit (no cll uttons) D, you do not need to press the uttons tht re shown s flshing in figure B. Once progrmming is complete, you re utomticlly tken to progrmming clls. Progrmming clls The LED flshes. Lift the internl receiver hndset (if present) nd UX2 uttons E. On nd press the door lock relese the entry pnel, press the cll utton to e linked to the internl receiver F. eep confirms tht the setting hs een stored F. End the cll nd repet for the other internl receivers. NOTE. You cn force the switch from one progrmming mode to nother y pressing the utton on the power supply unit for 3 seconds nd relesing within 6 seconds. If you force the switch to cll progrmming from utton progrmming, the utton units which hve not een progrmmed re configured to 8 clls. If the se unit is not progrmmed, clls re not configured. E F Exiting Progrmming Press the utton riefly G. The LEDs on the entry pnel switch off. <1 G djusting the rightness nd colour of the unit cklight H c During cll progrmming H①, you cn djust the rightness nd colour of the unit cklight. Press the left cll utton to select white H ② nd the right cll utton to select lue H③. Press the sme utton repetedly to select one of the five rightness levels (off, 25%, 50%, 75%, 100%).
I Progrmming the entry pnel video cmer While progrmming clls, the visul rnge of the video cmer cn e djusted from ny receiver. To do this, lift the hndset (where present) nd press the self-connection utton I. From the defult configurtion, scroll through the susequent configurtions J pressing the UX1 utton, or go ck to the previous configurtions y pressing the UX2 utton K. Settings re sved utomticlly. 0 100 82 6 2 7 J M B C 72 1 9 54 Reprogrmming >20 >8 <11 4 8 1 3 5 9 K djusting the rightness level of the light on the entry pnel While progrmming clls L the rightness level of the light on the entry pnel cn e djusted from ny receiver. Pressing the self-connection utton on the internl receiver L ctivtes the video cmer on the entry pnel for which the rightness level of the light is to e djusted. Use previously ssigned cll utton to increse/decrese the rightness of the light M. Reprogrmming system which hs lredy een progrmmed, you ccess the cll progrmming phse directly. To ccess utton reprogrmming, follow the process for forcing the mode switch descried ove. If you dd, replce or remove n entry pnel, you must follow the progrmming uttons procedure so tht the system recognises the chnges. L Progrmming n intercommunicting group NOTE: Leve the function disled if the entry pnel is connected to V/01, /01 or VSE/301.01. Before progrmming n intercommunicting group, enle the intercommunicting function. This function is disled y defult. Enling/disling Press the utton on the entry pnel nd hold for t lest 20 seconds. The red nd yellow LEDs flsh quickly for 3 seconds B. NOTE: If the intercommunicting function is disled, follow this procedure to enle it, nd vice vers. The yellow LED comes on for 2 seconds to show the function hs een enled or the red LED comes for 2 seconds to show the function hs een disled. NOTE. Progrm the intercommunicting group fter ssigning clls to ll internl receivers. Progrmming n intercommunicting group Press the utton on the entry pnel for t lest 8 seconds nd relese within 11 seconds C. The red nd yellow LEDs flsh to show intercom progrmming is in progressd. Pge 4 - Mnul FB00329-EN - vers. 1-05/2016- Cme S.p.. - The contents of the mnul re to e considered s suject to chnge t ny time nd without the need for ny dvnce wrning.
To enle the intercommunicting function, press the intercommunicting cll utton you wnt to cll on the internl receiver you wnt to progrm E. eep indictes tht the function hs een progrmmed successfully. Repet for ll internl receivers to e included in the intercommunicting group. To conclude the progrmming, press the utton on the entry pnel riefly F. Pge 5 - Mnul FB00329-EN - vers. 1-05/2016- Cme S.p.. - The contents of the mnul re to e considered s suject to chnge t ny time nd without the need for ny dvnce wrning. D NOTE. Once n internl receiver hs een included in group y ssigning the intercommunicting cll utton, it cnnot e excluded from this group. If you wnt to chnge the cll utton on n internl receiver which hs lredy een progrmmed s n intercommunicting receiver, or you wnt to dd new internl receivers to the group, repet the opertions detiled under progrmming n intercommunicting group. E F <1 RMMING ENTRY PNELS WITH V/01 OR /01 Progrmming for the first time Entering progrmming mode >3 M1 Press the utton on the power supply until the LED lights up. nd nd the utton LEDs flsh to show the uttons re eing prothe LEDs grmmed B. 1 P.E. B 2 P.E. 2 P.E. 2 P.E. D 1 P.E. E 2 P.E. 1 P.E. 1 P.E. C Progrmming uttons Press the first cll utton on ech unit C D (see cll numer nd the utton LEDs stop flshing. section) until the lue LED NOTE. The LED lights on the unit remin on to show tht the uttons hve een progrmmed correctly. NOTE. For the sic unit (no cll uttons), you do not need to press the uttons tht re shown s flshing in figure B. Repet for ll entry pnels to e progrmmed. Once progrmming is complete, the configurtion is implemented E nd you re utomticlly tken to progrmming clls.
Progrmming clls F G NOTE. The opertion cn only e crried out from the entry pnel with the lue LED off (1 entry pnel in F). To chnge the entry pnel from which clls re progrmmed, press one of the cll uttons on the entry pnel you wish to use for progrmming. NOTE. You cn force the switch from one progrmming mode to nother y pressing the utton on the power supply unit for 3 seconds nd relesing within 6 seconds. If you force the switch to cll progrmming from utton progrmming, the utton units which hve not een progrmmed re configured to 8 clls. If the se unit is not progrmmed, clls re not configured. Exiting Progrmming Press the utton riefly H. The LEDs on the entry pnel switch off. <1 M1 H djusting the rightness nd colour of the unit cklight c During cll progrmming I, you cn control the rightness nd colour of the unit cklight. Press the left cll utton to select white I, nd the right cll utton to select lue I c. Press the sme utton repetedly to select one of the five rightness levels (off, 25%, 50%, 75%, 100%). I Progrmming the entry pnel video cmer While progrmming the clls, the visul rnge of the video cmer cn e djusted from ny receiver. To do this, lift the hndset (where present) nd press the self-connection utton J. Strting from the defult configurtion, scroll through the susequent configurtions K y pressing the UX1 utton, or go ck to the previous configurtions y pressing the UX2 utton L. Settings re sved utomticlly. J 0 100 82 1 9 72 K 54 6 2 7 4 1 5 8 3 9 L M Pge 6 - Mnul FB00329-EN - vers. 1-05/2016- Cme S.p.. - The contents of the mnul re to e considered s suject to chnge t ny time nd without the need for ny dvnce wrning. The green LED flshes. Lift the internl receiver hndset (if nd UX2 utpresent) nd press the door lock relese tons F. On the entry pnel, press the cll utton to e linked to the internl receiver G. eep confirms tht the setting hs een stored G. End the cll nd repet for the other internl receivers.
N djusting the rightness level of the light on the entry pnel While progrmming clls M the rightness level of the entry pnel cn e djusted from ny receiver. Pressing the self-connection utton on the internl receiver M ctivtes the video cmer on the entry pnel for which the rightness level is to e djusted. Use previously ssigned cll utton to increse/decrese rightness of the light N. Pge 7 - Mnul FB00329-EN - vers. 1-05/2016- Cme S.p.. - The contents of the mnul re to e considered s suject to chnge t ny time nd without the need for ny dvnce wrning. Reprogrmming Reprogrmming system which hs lredy een progrmmed, you ccess the cll progrmming phse directly. To ccess utton reprogrmming, follow the process for forcing the mode switch descried ove. If you dd, replce or remove n entry pnel, you must follow the progrmming uttons procedure so tht the system recognises the chnges. RESTORE FCTORY DEFULT To restore the entry pnel to the defult settings (including the terminl functions, ), remove the power supply, press nd hold the two cll uttons on the unit nd power the device. fter 5 seconds the entry pnel restrts. NOTE. If the entry pnel does not restrt, it hs not een restored to defult settings. This product complies with the relevnt directives in force. Decommissioning nd disposl. Dispose of the pckging nd the device t the end of its life cycle responsily, in complince with the lws in force in the country where the product is used. The recyclle components re mrked with symol nd the mteril's ID mrker. THE DT ND INFORMTION SHOWN IN THIS MNUL RE TO BE CONSIDERED S SUBJECT TO CHNGE T NY TIME ND WITHOUT THE NEED FOR NY DVNCE WRNING. MESUREMENTS, UNLESS OTHERWISE INDICTED, RE IN MILLIMETRES.
English - Mnul FB00329-EN - vers. 1-05/2016 - Cme S.p.. The contents of the mnul re to e considered s suject to chnge t ny time nd without the need for ny dvnce wrning. Cme S.p.. Vi Mrtiri Dell Liertà, 15 Vi Corni, 1/ - 1/c 31030 Dosson di Csier Treviso - Itly (+39) 0422 4940 (+39) 0422 4941 www.cme.com 33079 Sesto l Reghen Pordenone - Itly (+39) 0434 698111 (+39) 0434 698434