Detailed Simulation of Voltage and Frequency Controller for Wind Generating System with Unbalanced Linear Load with Fixed Wind Speed

Similar documents
Comparison of Reference Compensating Current Estimation Techniques for Shunt Active Filter

Tuned PI Controller using Zeigler-Nichols Method for Power Quality Enhancement for linear and non linear loads

An Improved Electronic Load Controller for Self- Excited Induction Generator in Micro-Hydel Applications

Static Voltage and Frequency Regulation of Standalone Wind Energy Conversion System

CHAPTER 4 INSTANTANEOUS SYMMETRICAL COMPONENT THEORY

Microelectronic Circuits

Scilab/Scicos Modeling, Simulation and PC Based Implementation of Closed Loop Speed Control of VSI Fed Induction Motor Drive

Research on Controller of Micro-hydro Power System Nan XIE 1,a, Dezhi QI 2,b,Weimin CHEN 2,c, Wei WANG 2,d

Smart Grid Technologies for Reactive Power Compensation in Motor Start Applications

COMPARISON ANALYSIS OF SHUNT ACTIVE FILTER AND TRANSFORMERLESS PARALLEL HYBRID ACTIVE FILTER

Design of Shunt Active Filter for Harmonic Compensation in a 3 Phase 3 Wire Distribution Network

Mitigation of Harmonics in Micro Grid using Photo Voltaic cell interfaced Shunt Active Power Filter

Closed Loop Topology of Converter for Variable Speed PMSM Drive

On-Line Capacitance Estimation of DC-Link Electrolytic Capacitor by Input Current Injection for ac/dc PWM Converters. I.

Figure.1. Basic model of an impedance source converter JCHPS Special Issue 12: August Page 13

An Improved Active Filter Technique for Power Quality Control under Unbalanced Dynamic Load Condition

POLYTECHNIC UNIVERSITY Electrical Engineering Department. EE SOPHOMORE LABORATORY Experiment 1 Laboratory Energy Sources

Keywords: Fuzzy logic controller, PI controller, Shunt Active power filter, SRF method. Fig 1: Structure of three phase four wire APF

Control of Chaos in Positive Output Luo Converter by means of Time Delay Feedback

ECE 2133 Electronic Circuits. Dept. of Electrical and Computer Engineering International Islamic University Malaysia

Harmonic Balance of Nonlinear RF Circuits

INSTANTANEOUS TORQUE CONTROL OF MICROSTEPPING BIPOLAR PWM DRIVE OF TWO-PHASE STEPPING MOTOR

antenna antenna (4.139)

Active and Reactive Power Control of DFIG for Wind Energy Conversion Using Back to Back Converters (PWM Technique)

High Gain Soft-switching Bidirectional DC-DC Converters for Eco-friendly Vehicles

Control of Drivetrain Boost DC DC Converter

Control of Venturini Method Based Matrix Converter in Input Voltage Variations

To: Professor Avitabile Date: February 4, 2003 From: Mechanical Student Subject: Experiment #1 Numerical Methods Using Excel

Hassan II University, Casablanca, Morocco

Analysis, Design, and Simulation of a Novel Current Sensing Circuit

H-Bridge VSC Based Voltage Controller for an Isolated Asynchronous Generator Supplying Three-Phase Four- Wire Loads

Interharmonic Mitigation Using Boost Converter In Variable Speed Drives

Chapter 13. Filters Introduction Ideal Filter

Voltage Quality Enhancement and Fault Current Limiting with Z-Source based Series Active Filter

Operation of Shunt Active Power Filter Under Unbalanced and Distorted Load Conditions

Characteristics of New Single Phase Voltage Doubler Rectifier Circuit using the Partial Switching Strategy

IDENTIFICATION AND MITIGATION OF POWER QUALITY DISTURBANCES USING IUPQC BASED ON PSODV TECHNIQUE

ACTIVE RESISTANCE EMULATION IN THREE-PHASE RECTIFIER WITH SUBOPTIMAL CURRENT INJECTION

A NEW ACTIVE POWER LINE CONDITIONER FOR COMPENSATION IN UNBALANCED/DISTORTED ELECTRICAL POWER SYSTEMS

Real time digital simulation of shunt active filter for mitigation of current harmonics with P-Q theory

Fuzzy Logic Controlled Shunt Active Power Filter for Three-phase Four-wire Systems with Balanced and Unbalanced Loads

ANALYTICAL DESIGN AND SIMULATION OF A STATCOM FOR COMPENSATING OF REACTIVE POWER CONNECTED TO NON- LINEAR LOADS IN POWER SYSTEMS

Modeling and Control of a Cascaded Boost Converter for a Battery Electric Vehicle

A Series Connected Three-Level Inverter Topology For Medium Voltage Squirrel Cage Motor Drive Applications

The Comparison Study of Current Control Techniques for Active Power Filters

Modeling and Design Considerations of Coupled Inductor Converters

Dual Functional Z-Source Based Dynamic Voltage Restorer to Voltage Quality Improvement and Fault Current Limiting

Rejection of PSK Interference in DS-SS/PSK System Using Adaptive Transversal Filter with Conditional Response Recalculation

Uncertainty in measurements of power and energy on power networks

Dynamic Optimization. Assignment 1. Sasanka Nagavalli January 29, 2013 Robotics Institute Carnegie Mellon University

CONSTANT INPUT POWER CONTROL OF THREE-PHASE ISOLATED BUCK+BOOST RECTIFIER * A. MOHAMMADPOUR AND M. R. ZOLGHADRI **

Passive Filters. References: Barbow (pp ), Hayes & Horowitz (pp 32-60), Rizzoni (Chap. 6)

Energy Comparison of MPPT Techniques Using Cuk Converter

Simulation of Distributed Power-Flow Controller (Dpfc)

Integrated Dual Output Buck Boost Converter for Industrial Application.

SPST (single-pole single-throw) switches

Chapter 4: Switch realization

Figure 1. DC-DC Boost Converter

Realization of Unified Power Quality Conditioner for Mitigating All Voltage Collapse Issues

Modeling and Control of Three-Phase Shunt Active Power Filter

Sensors for Motion and Position Measurement

A Novel Reference Current Generation Algorithm for Harmonic and Reactive Power Compensation in Non Ideal Three-phase Systems

Analysis, Voltage Control and Experiments on a Self Excited Induction Generator

3-Phase 4-Wire Shunt Active Power Filter with Renewable Energy Interface

High Speed ADC Sampling Transients

Aalborg Universitet. Published in: Proceeding of the 5th Nordic Wind Power Conference. Publication date: 2009

PULSEWIDTH-modulated (PWM) voltage-source inverters

Reactive power compensation for nonlinear loads using Fuzzy controller

Integrated Electronic Load Controller with T-Connected Transformer for Isolated Asynchronous Generator

Innovative Design of the Fast Switching Power Supplies for the SOLEIL EMPHU Insertion and its Fast Correctors

ECE315 / ECE515 Lecture 5 Date:

Soft-Switched CCM Boost Converter with High Voltage Gain for High Power Applications

Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab


Modeling, Analysis and Control of Hexagram Inverter for Three- Phase Induction Motor Drive

Controller Design Using Coefficient Diagram Methods for Matrix Converter Based Unified Power Flow Controllers

Electronic Load Controller for a Parallel Operated Isolated Asynchronous Generator Feeding Various Loads

Low Switching Frequency Active Harmonic Elimination in Multilevel Converters with Unequal DC Voltages

A Novel Voltage and Frequency Control Scheme for a Wind Turbine Driven Isolated Asynchronous Generator

Shunt Active Filters (SAF)

Active and Reactive Power Metering in Non-Sinusoidal Conditions Using Newton Type Algorithm

STUDY OF MATRIX CONVERTER BASED UNIFIED POWER FLOW CONTROLLER APPLIED PI-D CONTROLLER

Customer witness testing guide

An Adaptive Over-current Protection Scheme for MV Distribution Networks Including DG

Aalborg Universitet. Published in: I E E E Transactions on Industrial Electronics. DOI (link to publication from Publisher): /TIE.2014.

An Efficient Bridgeless PFC Cuk Converter Based PMBLDCM Drive

Figure 1. DC-DC Boost Converter

Implementation of Fan6982 Single Phase Apfc with Analog Controller

A High-Sensitivity Oversampling Digital Signal Detection Technique for CMOS Image Sensors Using Non-destructive Intermediate High-Speed Readout Mode

Lecture 10: Bipolar Junction Transistor Construction. NPN Physical Operation.

Journal of Engineering Science and Technology Review 5 (2) (2012) Research Article. P.M.Balasubramaniam 1,* and G.

Comparative Analysis of Reuse 1 and 3 in Cellular Network Based On SIR Distribution and Rate

IEE Electronics Letters, vol 34, no 17, August 1998, pp ESTIMATING STARTING POINT OF CONDUCTION OF CMOS GATES

High Speed, Low Power And Area Efficient Carry-Select Adder

Three-Phase Grid-Connected PV System With Active And Reactive Power Control Using dq0 Transformation

Introduction to Amplifiers

A Novel 10kW 2-U Three-Phase Unity Power Factor Rectifier Module

STATCOM with FLC and Pi Controller for a Three-Phase SEIG Feeding Single-Phase Loads

Walsh Function Based Synthesis Method of PWM Pattern for Full-Bridge Inverter

Power Factor Correction with AC-DC Buck Converter

Transcription:

Internatonal Journal of Scentfc and Research Publcatons, Volume, Issue, March 0 Detaled Smulaton of Voltage and Frequency Controller for Wnd Generatng System wth Unbalanced Lnear Load wth Fxed Wnd Speed Nnu Joy, Benny Cheran, Salce Peter Assstant professor, Dept of EEE, M.A College of Engneerng, Kothamangalam, Inda Professor, Dept of EEE, M.A College of Engneerng, Kothamangalam, Inda Professor, Dept of EEE, M.A College of Engneerng, Kothamangalam, Inda Abstract- Ths paper deals wth Voltage and frequency controller for wnd generatng system wth unbalanced lnear loads. The proposed system s modelled and smulated n MATLAB usng smulnk.the controller that controls both oltage and frequency of an asynchronous generator along wth ts mproement of power qualty. The proposed controller has bdrectonal acte and reacte power flow capablty along wth battery energy storage system by whch t controls the system oltage and frequency wth araton of consumer load. Index Terms- Battery energy storage system, solated asynchronous generator, oltage and frequency controller, wnd energy conerson system. T I. INTRODUCTION oday the need for renewable sources s ncreasng partcularly wnd.because wnd s the most promnent source of energy aalable. We can easly explot by usng asynchronous generator.squrrel cage nducton are low cost, robust and smple n ts constructon. Here employng a oltage and frequency controller for standalone wnd power generatng systems n order to mantan oltage and frequency. The proposed oltage and frequency controller s hang bdrectonal acte and reacte power flow capablty by whch t controls the system oltage and frequency wth araton of consumer loads and wnd.the performance s demonstrated usng standard MATLAB software. Here we can dscuss about detaled smulaton of ths scheme. II. SYSTEM CONFIGURATION Fg.. Schematc dagram of the proposed solated wnd energy system The complete off grd stand alone system wth asynchronous generator, wnd turbne, exctaton capactor, balanced/unbalanced, lnear/non-lnear/dynamc consumer loads and proposed controller s shown n Fg.. The proposed controller ncludes three-phase nsulated gate bpolar juncton transstor IGBT based oltage source conerter VSC along wth a battery at ts lnk. The controller s connected at the pont of common couplng PCC through the nter-facng nductor []. The exctaton capactor s selected to generate the rated oltage at no-load whle addtonal demand of reacte power s met by the controller. III. CONTROL SCHEME Fg..Schematc dagram of the proposed control strategy for an solated wnd energy system Fg demonstrates the control strategy of the proposed controller whch s based on the generaton of reference source currents. Reference source currents are hang two components one s reacte component for controllng the magntude of the generated oltage and other one s the acte component for regulatng the frequency of the generated oltage. The ampltude of acte power component of the source current s estmated by ddng the dfference of fltered load power and output of PI frequency controller to the ampltude of the termnal oltage. Multplcaton of wth n-phase unt templates yelds the n-phase component of reference source currents. These templates are, three-phase snusodal functons whch are dered by ddng

Internatonal Journal of Scentfc and Research Publcatons, Volume, Issue, March 0 the ac oltages by ther ampltude. To generate the reacte component of reference source currents another set of unt templates s dered from n-phase unt template and whch are 90 leadng from the correspondng oltages. The multplcaton of these templates and output of PI Proportonal Integral termnal oltage controller ges the reacte component of reference source currents.the sum of nstantaneous reacte and acte Components of currents ges the total reference source currents and these are compared wth the sensed source currents. The amplfed current error sgnals are compared wth fxed frequency 0 khz trangular carrer wae to generate the PWM swtchng sgnals for the deces of VSC. IV. MODELING OF THE CONTROL SCHEME Basc equatons of the control scheme of the proposed controller are as follows. A. Computaton of Acte Component of Reference Source Current Acte component of reference source current s estmated by ddng the dfference of fltered nstantaneous load power PLflter P and output of the PI frequency controller C to the V termnal oltage tm. The load power P L s estmated as by takng three-phase to two-phase transform la lb lc lb lc lb lc la lb lc 4 Instantaneous acte power s estmated as P L 5 It s fltered to achee ts component P Lflter. The frequency error s defned as f ern = f ref n - f n 6 Where f ref reference frequency 50 Hz n present system and f s the frequency of the oltage of an asynchronous generator. The nstantaneous alue of f s estmated usng phase locked loop PLL. At the th samplng nstant the output of frequency PI controller Pc s as P cn = P cn- + K pf {f ern -f ern- }+ K f f ern 7 Where K pf and K f are the proportonal and ntegral gan constants of the frequency proportonal ntegral PI controller. Then acte component of reference source current I dm s calculated as P LFlter P c I dm tm 8 The nstantaneous lne oltages at the termnals of an asynchronous generator la, lb and lc are consdered snusodal and ther ampltude s computed as 8 4.9 Vtm { la lb lc } The unty ampltude templates are hang nstantaneous alue n phase wth nstantaneous oltage la, lb and lc, whch are dered as V 8 9999999998 4.0 la da Vlb Vlc V d tm b Vtm Vtm B. Computaton of Reacte Component of Reference Source Current Instantaneous alues of n-phase components of reference source currents are estmated as rda = I dm da,, rdb = I dm db, r = I dm The ac oltage error at the n th samplng nstant as V ern = V tmrefn V tmn Where V tmrefn s the ampltude of reference ac termnal oltage and V tmn s the ampltude of the sensed three-phase ac oltage at the termnals of an asynchronous generator at n th nstant. The output of the PI controller I qmn for mantanng constant ac termnal oltage at the n th samplng nstant s expressed as I qmn =I qmn- +K pa {V ern V ern- +K a V ern } Where K pa and K a are the proportonal and ntegral gan constants of the oltage proportonal ntegral PI controller alues are gen n Appendx. V ern and V ern- are the oltage errors n nth and n-th nstant and s the ampltude of quadrature component of the reference source current at n- th nstant.the nstantaneous quadrature components of reference source currents are estmated as I rqa = I qm qa,,i rqb =I qm qb,i rqc = I qm qc 4 where q a, q b and q c and are another set of unt ectors hang a phase shft of 90 0 leadng the correspondng unt ectors, and whch are computed as follows: db qa 5 da db qb 6

Internatonal Journal of Scentfc and Research Publcatons, Volume, Issue, March 0 q c da db 7 C. Computaton of Reference Source Current Total reference source currents are sum of n-phase and quadrature components of the reference source currents as rsa = rqa + rda 8 rsb = rqb + rdb 9 rsc = rqc + r 0 D. PWM Sgnal Generaton Reference source currents rsa, rsb and rsc are compared wth sensed source currents sa, sb and sc. The current errors are computed as rsaerr = rsa - sa rsberr = rsb - sb rscerr = rsc - sc These current errors are amplfed wth a gan K and the amplfed sgnals are compared wth fxed frequency 0 khz trangular carrer wae of ampltude to generate gatng sgnals for IGBTs of VSC of the controller. V. ANALYSIS AND DESIGN A.Desgn Of Three Leg VFC Parameters of VFCs are desgned for a -kw, 45-V, 50- Hz asynchronous generator-based standalone WECS. It s reported that for feedng reacte power n the case of 0.8-pf laggng reacte loads, an IAG requres 40 60% of the reacte power of the rated generated power. Therefore, the VAR ratng of the VFC requred for kw P A generator s around 0 kvar. Then, the apparent power SA s gen as S A = P A + Q A = + 0 = 7 kva. So the current ratng of VSC s V C = 7 kva I C = 5.7 A. The ampltude of the current s I C pk = 7.9 A. The aerage current s I ag = 0.9 5.7 A = 46.5 A. I Here, the modulaton ndex m a s consdered equal to alue of. The rpple current through the nductor s taken 5%Oerloadng factor due to transent condton ares from 0% to 80% The swtchng frequency of 0 khz s selected for IGBTs of VSCs. The flter nductor s calculated by substtutng the alues of parameters as L an = L bn = L cn = ma * * f * I = mh. The lnk oltage s selected as V V = 677 V. s LRpple The lnk capactor can be estmated by consderng the oltage rpple across t. The alue of the capactor can be determned by the followng equaton: V Rpple cdt c Iag C I ag = 46.5 A, and ω = 4 rad/s for a 50-Hz WECS, the alue of the bus capactor s gen as V Rpple Consderng V Rpple =.54V Iag C V Rpple of % ==5475.6 F VI. SIMULATION, RESULTS AND DISCUSSION Model wth oltage and frequency control s modelled usng MATLAB for lnear unbalanced loads. The results are gen below and we can see dstorton s ery much reduced. A.Smulaton of the Controller Feedng unbalanced LnearLoads On the bass of earler current ratng, the peak-to-peak current rpple consderng 5% of the peak current through the flter nductor can be estmated as I Lrpplepk pk = 0.05 7.9A =.6595A. By estmatng ths current rpple and the aerage alue of the current, the alue of flter nductors and lnk capactors can be estmated for arous VFC topologes as follows

Internatonal Journal of Scentfc and Research Publcatons, Volume, Issue, March 0 4 Fg.6.Computaton of acte component of reference source current Fg..Wnd generator feedng unbalanced lnear load Fg..Wnd generator feedng unbalanced lnear load. The unbalance s gen usng breakers. The system frst started at no load,that s frst breaker n open poston. Then at s t s closed and load gen.then at. s unbalance s gen by openng phase at.s. Fg.7.Computaton of reacte component of reference source current and reference current generaton Fg.4.Wnd power generaton The subsystems for acte,reacte power, tm generaton generaton re gen below. Fg.8.Transent waeforms durng applcaton of balanced/unbalanced 0.8 pf laggng load at fxed wnd speed Fg.5. tm generaton Fg.8.demonstrates the performance of the controller for feedng unbalanced lnear loads.at s load s gen and later on at. s one phase of the load are opened usng breakers and the load becomes unbalanced but oltage and current at the generator termnals reman balanced under such worst case of load VII. CONCLUSION The performance of the proposed controller has been demonstrated for an solated wnd energy conerson system.

Internatonal Journal of Scentfc and Research Publcatons, Volume, Issue, March 0 5 Smulaton results hae erfed the performance of the controller under unbalanced lnear load. It has been obsered that the proposed controller has been found to regulate the magntude and frequency of the generated oltage constant n solated wnd power applcaton.. [6] J. M. Ramrez and E. Torres M, An electronc load controller for the selfexcted nducton generator, IEEE Trans. Energy Conerson, ol., no., pp. 546 548, Jun. 007. [7] L. A. C. Lopes and R. G. Almeda, Wnd-dren self excted nducton generator wth oltage and frequency regulated by a reduced ratng oltage source nerter, IEEE Trans. Energy Conerson, ol., no., pp. 97 04, Jun. 006 REFERENCES [] B. Sngh and Gaura Kumar Kasal Sold State Voltage And Frequency Controller For Stan Alone Wnd Power Generatng System, IEEE Trans. On Power Electroncs, ol., no., pp.70 77, May. 008 [] B. Sngh, S. S. Murthy, and S. Gupta, Analyss and desgn of STATCOM based regulator for self excted nducton generator, IEEE Trans. Energy Conerson, ol. 9, no. 4, pp. 78 790, Dec. 004. [] B. Sngh, S. S. Murthy, and S. Gupta, A oltage and frequency controller for self-excted nducton generators, Elect. Power Compon. Syst., ol. 4, pp. 4 57, Feb. 006. [4] B. Sngh, S. S. Murthy, and S. Gupta, Transent analyss of self excted nducton generator wth electronc load controller supplyng statc and dynamc loads, IEEE Trans. Ind. Appl., ol. 4, no. 5, pp. 94 04, Sep. 005. [5] B. Sngh, S. S. Murthy, and S. Gupta, Analyss and desgn of electronc load controller for self-excted nducton generators, IEEE Trans. Energy Conerson, ol., no., pp. 85 9, Mar. 006. AUTHORS Frst Author Nnu Joy dd BTech. Degree n Electrcal and Electroncs Engneerng at Vswa Jyoth college of Engneerng and Technology. and M. Tech n Power System from Santgts college of Engneerng,Pathamuttom. She currently holds the post of Assstant Professor n thedepartment of Electrcal and Electroncs M.A College of Engneerng, Kothamangalam.Her emal d:joynnujoy@gmal.com Second Author Benny cheran currently holds the post of Professor n the Department of Electrcal and Electroncs M.A College of Engneerng, Kothamangalam. Thrd Author Salce Peter currently holds the post of Professor n the Department of Electrcal and Electroncs M.A College of Engneerng, Kothamangalam.