BMW E90 Android Touch Screen Radio Installation Instructions Enjoy your new Android Radio from Bremmen Parts, we appreciate your business. Vibrant Touch Display This radio features a responsive 9 touch display capable of stunning HD resolution. Easy Installation: Each kit includes all required hardware for your specific vehicle, making installation quick and seamless. Easy Audio Streaming: Music can be easily streamed from your mobile device via bluetooth or USB. Music can also be listened to via flash drive, Micro SD, or imported to the radio s internal storage. Thousands of Apps: From the Google play store you can download your favorite audio streaming service, video streaming apps, or even apps that can diagnose and monitor your vehicles systems. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.
Listed below are the components which will need to be removed in order to install the new radio: 1. Climate control panel 2. Accessory panel 3. Factory radio 4. Factory radio cage 3 1 2 Listed below are the different ports on the back of the radio and components we will be plugging into them: 1. Wiring harness 2. Radio antenna 3. GPS antenna 4. WiFi antenna 5. USB port 2 4 5 3 1 This photo shows what the radio will look like once installed. All of the mounting brackets and hardware are included for an easy installation. 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 2 OF 10
1 2 3 4 8 5 6 7 9 10 1. USB Port 2. USB Adapter 3. Component Input Adapter 4. Radio Antenna Adapter 5. Climate Control Panel Trim Here s what s included in the box: 6. Climate Control Panel Bracket 7. Wiring Harness 8. CAN-bus Decoder 9. GPS Antenna 10. Wifi Antenna 1 2 3 Here s all the tools required for this install: 1. Phillips Screwdriver 2. Angled Pick 4. Trim Removal Tools 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 3 OF 10
Section 1: Removing the Stock Radio Step #1 Step #2 Step #3 Step #4 Ensure that your battery is disconnected prior to beginning installation. Use a non-marring trim removal tool to gently pry the climate control panel free. Remove the three connectors from the back of the climate control panel (arrows). Remove the accessory panel (highlighted in RED) from the climate control trim. Using a pick, lift up on the tabs to free the trim from the climate control panel. 1 2 3 4 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 4 OF 10
Section 1: Removing the Stock Radio Step #5 Step #6 Step #7 Step #8 Remove the two screws (arrows) which secures the factory radio to the cage. Pull the radio partially out of the cage then disconnect the antenna connector (highlighted in RED) from the back of the radio. Pry upward as shown on the factory connector sliding lock to release it from the back side of the unit. Set the radio aside. Remove the four screws (arrows) which secure the radio cage into the dash. Remove the cage. 5 6 7 8 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 5 OF 10
Section 2: Installing the New Radio Step #1 Step #2 Step #3 Step #4 Assemble the new climate control panel bracket as shown using the four screws (arrows). Install the bracket into the dash using the two screws from the factory radio cage. In order for the climate control panel to fit into the dash, slight trimming of the overhanging plastic tabs (arrows) on the climate control panel may be required. Reconnect the two connectors into the back of the climate control panel. 1 2 3 4 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 6 OF 10
Section 2: Installing the New Radio Step #5 Step #6 Step #7 Step #8 Install the climate control panel into the bracket. Ensure that the tabs on the sides of the panel are inserted into the clips on the bracket on either side. Install the provided trim piece onto the face of the climate control panel. Install the wiring harness into the factory connector and close the sliding lock. Install the CAN-bus decoder module into the white connector in the new harness. 5 6 7 8 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 7 OF 10
Section 2: Installing the New Radio Step #9 Step #10 Step #11 Step #12 Install the included radio antenna adapter onto the factory radio antenna cable. Plug the black connector on the new wiring harness into the back of the new radio. Plug the radio antenna adapter into the back of the new radio. Install the new GPS antenna by doing the following: - Find a suitable location to mount the GPS antenna which is clear of obstacles that may cause signal interference. - Mount the GPS antenna (arrow) in the desired location using double-sided tape or the integrated magnet. - Route the cable from the mounting location to the back of the new radio, removing trim panels to tuck and secure the cable as needed. 9 10 11 12 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 8 OF 10
Section 2: Installing the New Radio 13 Step #13 Step #14 Step #15 Step #16 Connect the GPS antenna connector into the back of the new radio. Screw the WiFi antenna (arrow) into the back of the new radio and tighten it until snug. Install the USB adapter harness (arrow) into the back of the new radio. Install the USB port by doing the following: - Find a convenient location to mount the USB port (arrow), we found the glove compartment to work well on this model. - Plug the USB port into the USB adapter labeled USB-OTG on the back of the new radio. - Route the USB port to the desired mounting location, removing trim panels to tuck and secure the cable as needed. 14 15 16 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 9 OF 10
Section 2: Installing the New Radio Step #17 Step #18 Slide the new radio into the dash and adjust it until the radio face is flush with the rest of the dash. Turn the radio on and test for functionality (sound, video, steering wheel controls, GPS, Wifi, etc.). Install the two mounting screws and tighten them until they are snug, but do not over tighten them. Install the two small black pieces to cover each screw hole. Congratulations, your installation is complete! 17 18 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM PAGE 10 OF 10