MANHATTAN TORA BD A RAD this sheet prior to assembly to familiarise yourself with the various stages of construction. Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly. arts Identification lease ensure that the packaging is disposed of in a safe environmentally friendly way. CAUTION: There are small components used in the construction of this unit. These loose items should be kept away from young children during assembly, to avoid the danger of choking. IMORTANT: BOR TARTIN TO AMB TH BD - A RAD TH INTRUCTION CARUY 6 8 9 Drawer parts x 4b 4a 4a 4b 0 4 6 Note: tandard wooden slat set (part ) Upgraded sprung slat frame (part ) arts Checklist Ref. Ref. Headboard 0 Drawer ace anels ootboard ide anels Drawer ide anels Drawer ront anels 4 4a&4b Adjustable upport egs / r Drawer Back anels 6 Wooden lat et Wooden lat et upport eg 4 Drawer Bottom anels Drawer Bottom upport Rails (nds) 4 8 *Upgraded prung lat rame* *prung lat rame Centre upport eg* 6 Drawer Bottom upport Rails (Centre) 9 *prung lat rame upport egs* 6040 age of 8 * Only supplied if upgraded sprung slat frame is chosen. egs (8&9) are only supplied with the sprung system.
ittings Checklist HARDWAR NDD OR BD AMBY (ACK A) Code Code A Bolts (M8x0mm) for fitting side panels () to headboard & footboard (&). D Allen Key (for M8 bolt) x B C pring Washers (for M8 bolts) lat Washers (for M8 bolts) x4 M Bolts (M8x4mm) for fitting adjustable support legs (4) to side panels (). x8 HARDWAR OR ITTIN WOOD AT OR URADD RUN AT RAM (ACK B) Code Code Bolts (M6x40mm) for fitting the wooden slat set () or the sprung slat frame () to H Allen Key (for M6 bolt) side panels () x leeve Nuts - M6 U crew for lat upport eg (6) - mm x lat Washers (for M6 bolts & mm screw) x pring Washers (for M6 bolts) XTRA HARDWAR NDD WHN ITTIN URADD RUN AT RAM Note: The following fittings will be found in the box which contains the upgraded metal frame itself. Bolts (M6xmm) for fitting support legs ( 8&9) to the sprung slat frame () x8 8 prung slat frame centre support leg x 9 prung slat frame support legs x Code HARDWAR NDD OR DRAWR AMBY (ACK C) crews (x0mm) for assembling drawer panels x8 K crews (x0mm) for fitting wheels (N) to wooden drawer support rails. x40 crews (4x0mm) for fitting drawer face panels (0) lastic Barrel Nuts x8 Code WH OR DRAWR (ACK D) N Drawer Wheels x0 age of 8
Additional Tools Required Cross-head crewdriver eneral Hints & Tips lease retain your assembly instruction and tools provided for future use. eriodically check that all bolts are still tight. Care & Maintenance In the unlikely event of missing or damaged parts, please contact the customer service team on 044 9 00 00. When calling this number, please quote the part code reference numbers shown in this leaflet when requesting spare or replacement parts. When they are supplied and are part of the assembly of this bed, ensure that the barrel nuts are fitted the correct way so the hole in the nut is facing towards the intersecting hole in the panel. This assembly requires two persons. Intersecting Hole We recommend the bed is assembled in the room it shall be located in. Bed Assembly - Use ack 'A' tage M x8 C x8 D x ix support legs (4) from inside bed frame into the pre-threaded holes in both side panels (). Make certain the labels are as shown in the diagrams - they must point towards each other. The legs are then in correct place to stop the drawer going under the bed. M C 4a ARROW ON AB OINT TOWARD ACH OTHR C 4b M Adjustable eet Carefully adjust feet so they just touch the floor keeping side panels level when bed is in use. age of 8
Bed Assembly - Use ack 'A' tage A B C D x oosely insert four bolts (A) with spring washers (B) & flat washers (C) into each side of headboard & footboard (&). 0mm Note: Do not tighten fully but leave 0mm protruding as in the diagram. IT BOT TO HADBOARD & OOTBOARD IK THI. & C B A it the side panels locating the brackets behind the flat washers. a. b. MAK CRTAIN TH BD I QUARD U, A HOWN IN TH DIARAM. Once all four corners are located, make sure the bed is square as in the sketch, then tighten all the bolts 00% using Allen key (D). age 4 of 8
itting lats - Use ack 'B' tage a ITTIN WOODN AT T x H x U x i: Carefully lay wooden slat set () on the metal supports on each side panel. Using two bolts () with spring washers (), flat washers () and sleeve nuts () fix one slat next to headboard. ii: Roll out wooden slats just over half way down the bed and using two more bolt sets, loosely bolt the central slat into position - align slats and fix all four bolt sets 00% by Allen key (H). iii: it centre slat with the support leg (6) using screw (U) and flat washer (). ully tighten using a cross-head screwdriver. U Carefully turn adjustable foot clockwise until it just touches the floor and slat is horizontal. 6 Adjustable oot iv: Roll out rest of wooden slats and fix with last two bolt sets fully tighten using Allen key (H). age of 8
itting lats - Use ack 'B' ITTIN URADD RUN AT RAM tage b x4 x4 x4 H x x8 x4 9 Open the metal slat frame () and lay face down on the working surface. it the support legs (8&9) to the positions shown securing with the bolts (). ully tighten using Allen key (H). 8 9 Carefully turn the slat frame over and position onto the metal slat supports on each side panel. Align the frame with the fixing holes at each end and secure using four sets of bolts (), spring washers (), flat washers () and sleeve-nuts (). When all in place tighten using Allen key (H). 9 8 9 inally, please check carefully that all bolts are fully tightened before the bed is used. age 6 of 8
Drawer Assembly - Use ack 'C' tage 4 i: x8 x8 6 IMORTANT: MAK UR WHN ITTIN TH NUT THAT TH HO I IN CORRCT AINMNT WITH TH HO IN TH AN D. ii: iii: v: 4 iv: vi: 6 age of 8
Drawer Assembly - Use ack 'C & D' tage K x40 N x0 K K K K N 0 it the assembled drawer to rear of Drawer ace anel (0). Carefully follow the guide lines. tage 6 ID IN TH DRAWR age 8 of 8