88 5549 181 Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. A. Top Q. Shelf F. Back Panel Hardware List Hex Wrench Small Hex Wrench Cam Lock 20 Pcs. (+4 extra) Cam Lock Screw 20 Pcs. (+1 extra) Magnet M3x10 Wood Screw for Magnet 2 Pcs. (+1 extra) M3x8 Wood Screw for Hinge 6 Pcs. (+1 extra) M3x20 Wood Screw (long) 47 Pcs. (+1 extra) M3x15 Wood Screw (short) 16 Pcs. (+1 extra) M6x25 Head Cap Bolt 8 Pcs. (+1 extra) For assembly see instructions in carton 88 5549 182 Adjustable Pin 4 Pcs. M4x25 Machine Screw 12 Pcs. Tools required for assembly : Phillips screwdriver Home Styles Consumer Assistance: www.homestyles-furniture.com, servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319 Pull Handle 6 Pcs.
88 5549 182 Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. G. Drawer B. Side Panel C. Side Panel D. Middle Panel E. Middle Panel H. Drawer I. Drawer M. Base N. Base O. Door P. Metal Strip 2 Pcs. L. Keyboard Front Also need the following from carton 88 5549 181 : J. Drawer K. Keyboard (Please refer to the last page of these instructions for drawer assembly steps.) Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level Home Styles Consumer Assistance: www.homestyles-furniture.com, servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
Assembly Instructions 32/10 IMPORTANT * Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * Do not tighten up all the bolts until each part is properly assembled. * Use a soft cloth between these parts and the fl oor. * After assembly item must be level to work properly. Use the included adjustable levelers to level. Insert Cam Lock Screws into pre-drilled holes of Top (A), Side Panels (B) and (C) and Back Panel (F). (See ) F A Cam Lock Screw B C Wood Screw for magnet D Attach Magnet to Middle Panel (D) with Wood Screw for magnet. (See )
STEP 3 Attach Middle Panel (D) to Base (M) and Middle Panel (E) to Base (N) with Head Cap Bolts. (See Figure 3) Assembly Instructions 43/10 M D E N Figure 3 Head Cap Bolt STEP 4 Attach units to Back Panel (F) with Cam Locks. (See Figure 4) Figure 4 F Cam Lock Cam Lock B STEP 5 Attach Side Panels (B) and (C) to unit with Cam Locks and Head Cap Bolts. C Head Cap Bolt
Assembly Instructions 54/10 A Cam Lock STEP 6 Turn the unit over to its upright position. Attach Top (A) to the unit with Cam Locks. L K Wood Screw for Hinge L Figure 5 STEP 7 Attach Keyboard Front (L) to Keyboard (K) with Wood Screws for Hinge. Attach Pull Handle to Keyboard Front (L) with Machine Screws. (See Figure 5)
Assembly Instructions 5/10 6 G O H I Q Adjustable Pin J Figure 6 Figure 7 Figure 8 Figure 9 STEP 8 Insert Adjustable Pins into the side panel and middle panel at the desired level. Place Shelf (Q) into position. Attach Pull Handle to Door (O) with Machine Screws. (See Figure 6) Attach Door (O) by sliding the door lift hinges into the side panel lift hinges. (See Figure 7) Slide Drawers (G), (H), (I), (J) and keyboard into position. If you want to remove the keyboard or file drawer in the future, push the plastic lever on its left side up, push the plastic lever on its right side down and pull open slowly. (See Figure 8) To level the unit, adjust the adjustable levelers on the bottom of the base legs. (See Figure 9) Note : Unit must be level to work properly.
Drawer (G) Assembly Instructions 76/10 G3 G1 G2 G4 Attach G1, G2 and G3 using a Phillips screwdriver and long Wood Screws (4X), tighten halfway. MAKE SURE ROLLER IS ON THE BACK Attach G1, G2 and G4 using long Wood Screws (4X), tighten halfway. (See ) Slide G5 into grooves in G3 and G4. Be sure to push G5 all the way forward so it meet G1. (See ) G3 G5 G1 G4 G5 STEP 3 Figure 3 Insert short Wood Screws (4X) into the pre-drilled holes in G5, tighten screws. (See Figure 3) STEP 4 Attach Pull Handle with Machine Screws. (See Figure 4) Tighten all screws used in drawer assembly. Figure 4 G1. Front Part G2. Back Part G3. Pc. G4. G5. Base Part
Drawer (H) Assembly Instructions 87/10 H3 H1 H2 H4 Attach H1, H2 and H3 using a Phillips screwdriver and long Wood Screws (4X), tighten halfway. MAKE SURE ROLLER IS ON THE BACK Attach H1, H2 and H4 using long Wood Screws (4X), tighten halfway. (See ) Slide H5 into grooves in H3 and H4. Be sure to push H5 all the way forward so it meet H1. (See ) H3 H5 H1 H4 H5 STEP 3 Figure 3 Insert short Wood Screws (4X) into the pre-drilled holes in H5, tighten screws. (See Figure 3) STEP 4 Attach Pull Handle with Machine Screws. (See Figure 4) Tighten all screws used in drawer assembly. Figure 4 H1. Front Part H2. Back Part H3. Pc. H4. H5. Base Part
Drawer (I) Assembly Instructions 8/10 9 I3 I2 MAKE SURE ROLLER IS ON THE BACK I1 I4 Slide I5 into grooves in I3 and I4. Be sure to push I5 all the way forward so it meet I1. (See ) Attach I1, I2 and I3 using a Phillips screwdriver and long Wood Screws (4X), tighten halfway. Attach I1, I2 and I4 using long Wood Screws (4X), tighten halfway. (See ) I3 I5 I1 I4 I5 STEP 3 Insert short Wood Screws (4X) into the pre-drilled holes in I5, tighten screws. (See Figure 3) Figure 3 STEP 4 Attach Pull Handle with Machine Screws. (See Figure 4) Tighten all screws used in drawer assembly. Figure 4 I1. Front Part I2. Back Part I3. I4. I5. Base Part
Drawer (J) Assembly Instructions 9/10 J3 J1 J2 J4 Attach J1, J2 and J3 using a Phillips screwdriver and long Wood Screws (6X), tighten halfway. Slide J5 into grooves in J3 and J4. Be sure to push J5 all the way forward so it meet J1. (See ) J5 P J3 Attach J1, J2 and J4 using long Wood Screws (6X), tighten halfway. (See ) J5 J4 Figure 3 J1 STEP 3 Insert short Wood Screws (4X) into the pre-drilled holes in J5, tighten screws. (See Figure 3) STEP 4 Attach Pull Handle with Machine Screws. (See Figure 4) Legal Size Legal Size STEP 5 Figure 4 Tighten all screws used in drawer assembly. Figure 5 Place Metal Strops (P) into position. (See Figure 5) The Metal Strips can be adjusted for letter size or legal size fi les as shown. J1. Front Part J2. Back Part J3. J4. J5. Base Part
Keyboard (K) Assembly Instructions10/10 11 K4 K1 Attach K1 to K4, using a Phillips screwdriver and long Wood Screws (3X), tighten halfway. (See ) K2 K3 Attach K2 and K3 to unit, using a Phillips screwdriver and long Wood Screws (8X), tighten halfway. (See ) Tighten all screws used in drawer assembly. K1. Back Part K2. K3. K4. Base Part