K-KR4Z - Kona INSTRUCTION MANUAL 07.10 KK002
Please keep this manual and product code number for future reference and replacement parts ordering if necessary. CURVED GLASS SLIDING SHOWER DOOR
CURVED GLASS SLIDING SHOWER DOOR INSTALLATION INSTRUCTIONS FOR CURVED GLASS SLIDING SHOWER DOOR Congratulations! You have made the right choice in buying this shower system. We are convinced that you will be entirely satisfied with our product. READ CAREFULLY AND COMPLETELY BEFORE PROCEEDING IT IS RECOMMENDED THAT YOU WEAR SAFETY GLASSES AT ALL TIMES DURING INSTALLATION INSTALLATION OVER CERAMIC TILE If your shower door is to be installed over ceramic tile, tile should extend completely under both wall jambs. Silicone should be used to seal the line where ceramic tile meets the base. HOW TO CARE FOR YOUR DOOR Never use scouring powder pads or sharp instruments on metal work or glass panels. An occasional wiping down with a mild detergent diluted in water is all that is needed to keep the panels and aluminum parts looking new. Product specifications are subject to change without notice.
PACKAGING CHECK LIST & HARDWARE 11 9 1 2 3 8 4 5 6 10 7 1 WALL JAMB (2) 4 SET OF HANDLES (2) 8 SIDE GASKET WALL JAMB SIDE (2) 2 EXPANDER (2) 5 SIDE GASKET (4) 9 TOP TRACK (1) 3 FIXED PANEL (2) 6 7 DOOR PANEL ASSEMBLY (2) BOTTOM TRACK (1) 10 11 MAGNETIC DOOR GASKET (2) GLASS SUPPORT (8) PAGE 1
PACKAGING CHECK LIST & HARDWARE 4 5 8 10 OR FOR PARIS POINT GLASS ONLY SET OF HANDLES (2) SIDE GASKET (4) SIDE GASKET (2) MAGNETIC DOOR GASKET (2) 11 12 13 14 GLASS SUPPORT (8) BOTTOM SLIDER WALL PLUG (8) SHIM (4) SCREW 3/8 LG (8) (M4 X 8) 15 16 17 18 SCREW CAP (8) SCREW 1 3/8 LG (12) SCREW 15/32 LG (4) (M4 X 35) (M4 X 12) EXPANDER CAP (2) PAGE 2
REQUIRED TOOLS LIST 1/4 1/8 CERAMIC TILE DRILL BIT DRILL BIT HEX NUT DRIVER SCREWDRIVERS DRILL HACKSAW * HAMMER * Required for one piece shower unit installation. MALLET PENCIL SILICON LEVEL PAGE 3
NOTICE For one piece shower unit installation. Prior to installation, to fit the corner contour of your shower unit, it's recommended to round of the edge of wall jamb and/or expander with a hacksaw as shown. TOP VIEW WALLJAMB (2) Round-off edge OR EXPANDER & WALLJAMB (2) LEVEL shower unit Round-off edge NOTICE: If necessary, round-off a little more. Make sure that wall jambs and/or expander as well as bottom track lay leveled on the threshold of the shower unit. PAGE 4
1 EXPENDER (2) + TRACK (2) + SCREW 1 3/8 LG (4) TOP TRACK (1) 2 INSERT WALL JAMBS TEMPORALLY BOTTOM TRACK (1) PAGE 5
3 POSITION AND CENTER THE FRAME TOGETHER WITH WALLJAMBS ONTO THRESHOLD OF SHOWER BASE. 4 - ADJUST AND LEVEL THE FRAME ASSEMBLY. - TRACE OUTER EDGE OF WALL JAMBS. - REMOVE FRAME ASSEMBLY FROM BASE. ON BOTH SIDE PAGE 6
5A 5 - REALIGN WALL JAMB WITH REFERENCE LINE (2). - MARK DRILLING LOCATION FOLLOWING PILOT HOLES. - DRILL HOLES BY USING SUITABLE 1/4 DRILL BIT. 5B 6B 6A 6 - INSERT THE WALL PLUGS (8) AND PUT IN EACH A DROP OF SILICONE. - SECURE THE WALL JAMB USING 1 3/8 SCREWS (8) 6C PAGE 7
TOP TRACK 7 INSTALL THE FIXED PANELS (2) BY SECURING THEM WITH THE GLASS SUPPORTS (8) & SCREW 15/32 LG (4). GLASS SUPPORT GLASS ON BOTH SIDES BOTTOM TRACK A B C PAGE 8
8 INSERT ONE SIDE OF FRAME INTO WALL JAMB 9B 9A 9 ENGAGE THE OTHER SIDE OF FRAME INTO WALL JAMB PAGE 9
10 PRIOR TO INSTALL DOOR PANELS INSERT MAGNETIC DOOR GASKET (2) (OPTIONAL) PUSH DOWN 11C PUSH DOWN 11A 11B 11 INSERT DOOR PANELS INTO TOP & BOTTOM TRACK PAGE 10
12 USE HEX NUT DRIVER OR PLIERS FOR VERTICAL DOOR ADJUSTMENT LOOSEN TIGHTEN 12A 12B 12D 12E 12C VERTICAL ADJUSTMENT INSERT SIDE GASKET WALL JAMB SIDE (2) (both sides) 14 OR (FOR PARIS POINT GLASS ONLY) 13 INSTALL SIDE PANEL GASKET ONTO FIXED PANELS & DOOR PANELS (4) TOP VIEW PAGE 11
15 - LEVEL AND ADJUST FRAME - FASTEN FRAME WITH SCREW 3/8 LG (8) + SCREW CAP (8) B 1/8 A DRILL BIT B A PAGE 12
16 INSERT EXPANDER CAPS (2) 24 Hours 17 SILICONE EXTERIOR ON BOTH SIDE S, ALONG THE WALL JAMBS AND WALLS. ALSO ALONG THE BOTTOM TRACK AND THE SIDE PANELS. PAGE 13