Jointer Model: 0-0 Parts List Record the serial number and date of purchase on your parts list for future reference. Serial number: Date of purchase: Part # 0-0PL For more information: www.rikontools.com or info@rikontools.com For Parts or Questions: techsupport@rikontools.com or 8-88-
Troubleshooting WARNING! FOR YOUR OWN SAFETY, ALWAYS TURN OFF AND UNPLUG THE MACHINE BEFORE CARRYING OUT ANY TROUBLESHOOTING. Symptom Possible Cause Solution Motor will not start Machine not plugged in Plug the machine in Low Voltage Check for proper voltage Loose connection or open circuit in motor Inspect motor for loose connections Motor Overheats Motor overloaded Reduce load on motor. Feed work slower Air flow restricted on motor Clean out motor to obtain normal air flow Excessive motor noise Bad motor Have motor checked Pulley set screw loose Tighten set screw Motor will not develop full power or stalls Circuit overloaded with lights or other tools Decrease the load on the circuit Circuit too long or undersized wires Reduce the length of the wire or Increase the wire size Voltage too low Have the voltage checked by an electrician Circuit breakers do not have sufficient capacity Have a licensed electrician install proper size breakers Drive belt tension too high Adjust belt tension Use of extension cord Use heavier gauge extension cord or no extension cord Loose in feed or outfeed tables Loose gibs Tighten the gibs Finish stock is concave on the end Knives are set higher than the outfeed table Raise outfeed table level with knives Back side of finish stock is thicker than the front Outfeed table set too high Adjust outfeed table level with the knives Stock is concave in the middle Table out of level Raise the table ends Ripples on planed surface One blade set higher than the others Readjust blades Feed rate too high Feed workpiece slower Knives dull Replace knives or sharpen Knives are set higher than the outfeed table or not Kickback level with the table Readjust the knives Workpiece strikes the outfeed table Outfeed table set too high or blades to low Readjust knives level with outfeed table Fence not accurate at 90 or degrees Fence stop not properly adjusted Readjust the fence stops Machine bogs down in the cut Excessive depth of cut Decrease depth of cut Knives are dull Sharpen or replace knives Safety guard won't return to the fence No tension on the spring Retension saftey guard spring Broken tension spring Install new tension spring *********Warning********* Do not make adjustments while the Jointer is running. Ensure the switch is off, power is disconected and all moving parts have stopped before servicing. Failure to comply may result in serious injury
Index 8 9 0 8 Part A A A A A A A 8A 9A 0A A A A A A A A 8A Cutterhead Assembly Description Cutterhead Knife Knife Lock Bar Bearing Housing Bearing Housing Cutterhead Pulley Hex Screw/Cutterhead Locking Flat Washer mm Key Stud Bolt 0mm Lock Washer 0mm Screw/Cutterhead Set Ball Bearing 0 Ball Bearing 0 Pin Stop Spring Flat Washer 0mm Hex Bolt Mx Q ty
Fence Assembly 8
Fence Assembly Index 8 9 0 8 9 0 8 9 0 8 9 0 8 9 0 Part B B B B B B B 8B 9B 0B B B B B B B B 8B 9B 0B B B B B B B B 8B 9B 0B B B B B B B B 8B 9B 0B B B B B B B B 8B 9B 0B B B B B B B B Description Fence Body Handle Hex Nut 0mm Hex Socket Bolt M8-.x Block Hex Nut M8-. Hex Bolt M8-.x Plastic Bar Handle Cam Wheel Hex Socket Bolt M8-.x Hex Socket Bolt M8-.x Tilt Shaft Worm Gear Hex Bolt M8-.x0 Tube Tilt Plate Hex Bolt M-.0x Hex Nut Flat Washer mm Handle Hex Nut/Small Spring Handle Screw Handle Nut Quill Casting Quill Bracket Bolt M8-.x0 Gear Plate Screw/Phip M-.0x Handle Screw Handle Screw Adjusting Casting Set Screw Shaft Thread Shaft Flange Hex Socket Gear Shaft Key Lock Tube Tube Thread Rod Flat Washer mm Handle Hex Nut/Large Handle Wheel Flat Washer mm Hex Bolt M-.0x Special Lock Nut Q ty 9
Stand and Motor Assembly 0
Stand and Motor Assembly Index 8 9 0 8 9 0 8 9 0 8 9 0 8 9 0 Part C C C C C C C 8C 9C 0C C C C C C C C 8C 9C 0C C C C C C C C 8C 9C 0C C C C C C C C 8C 9C 0C C C C C C C C 8C 9C 0C C C Description Tapping Screw Switch Switch Box Stain Relief Bushing Cable Cable Switch Support (Upper) Lock Knob Switch Support (Lower) Hex Bolt M8-.x Flat Washer 8mm Pan Head Screw M-0.08x J-Belt 90 Hex Bolt M-.0x Flat Washer mm Motor Pulley Key Motor Carriage Bolt M8-.x Hex Nut M-0.08 Pan Head Screw Motor Mounting Plate Shaft Bracket Rubber Tube Lock Washer 8mm Hex Nut M8-. Pan Head Screw Screw Shaft Nut Screw Shaft Bracket Cable Knob Screw Washer Door Latch Lock Nut Rubber Feet Door Lock Bolt Stand Body Belt Cover Plastic Cap Plate Pan Head Screw Relief Plug Cable Bracket Dust Chute Pan Head Screw Tool Holder Q ty
Bed Assembly
Bed Assembly Index 8 9 0 8 9 0 8 9 0 8 9 0 8 9 0 Part D D D D D D D 8D 9D 0D D D D D D D 8D 9D 0D D D D D D D D 8D 9D 0D D D D D D D D 8D 9D 0D D D D D D D 8D 9D 0D Description Rear Table Lock Knob Adjust Nut Flat Washer 0mm Bushing Adjusting Screw Ball Crank Pivot Pin Set Screw Lock Screw Hand Wheel Handle Handle Shaft Bolt Front Table Retaining Washer Spring Spring Knob Retainer Pointer Ball Crank Base Gib Depth Scale Shoudler Pin Brass Washer 0mm Set Screw Set Screw Hen Nut Screw Rivet Washer Hex Nut Rivet Fence Base Casting Key Flat Washer 8mm Hex Bolt M8-.x Spring Pin /8" Set Block Hex Socket Bolt M8-.x Stud Spring Stud Knob Lock Handle Cutterhead Guard Guard Post Manual Q ty
WARRANTY -Year Limited Warranty RIKON Power Tools/Richen Enterprise, Inc. ( Seller ) warrants to only the original retail consumer/ purchaser of our products that each product be free from defects in materials and workmanship for a period of two () years from the date the product was purchased at retail. This warranty may not be transferred. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear. Under no circumstances will Seller be liable for incidental or consequential damages resulting from defective products. All other warranties, expressed or implied, whether of merchantability, fitness for purpose, or otherwise are expressly disclaimed by Seller. This warranty does not cover products used for commercial, industrial or educational purposes. This limited warranty does not apply to accessory items such as blades, drill bits, sanding discs or belts and other related items. Seller shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special, or consequential damages arising from the use of our products. To take advantage of this warranty proof of purchase documentation, which includes date of purchase and an explanation of the complaint, must be provided. The Seller reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. To take advantage of this warranty, please fill out the enclosed warranty card and send it to: RIKON Warranty 00 West Cummings Park Suite 000 Woburn, MA 080 The card must be entirely completed in order for it to be valid. If you have any questions please contact us at 8-88- or warranty@rikontools.com.
For more information: 00 West Cummings Park, Suite 000 Woburn, MA 080 8-88- / 8-9-800 techsupport@rikontools.com www.rikontools.com Copyright Richen Enterprise, Inc. 00 Printed in China