L Series Cabinets For information concerning all available sizes, please refer to the G01 brochure.

L Series Cabinets For information concerning all available sizes, please refer to the G01 brochure. Please ensure that you have the latest version before using this technical document. Specifications L50-JN18A 7PL50A00 The L drawer and cabinet Series: In terms of space optimization in cabinets, the Rousseau L drawer allows valuable floor space to be reclaimed and for the user to better organize their work space. With the drawer subdividing accessories available such as partitions, dividers, plastic bins, etc. you maximize use of all the space within the drawer. 8 cabinet dimensions are available and are designed for intensive use. The drawers have a 100 lb. capacity and open 100%. The cabinets are reinforced at strategic places assuring sturdiness and durability. Wheels and cart can be added to the cabinet to make them mobile. The cabinets and mobiles cabinets can be anchored side-by-side. Cabinet and drawers can be equipped with locks to secure your stored items. Rousseau L cabinets are compatible with our wide range of WS & WM workstation accessories. Combining the cabinets with accessories means that the user can customize their workstation configuration according to the type of work they are performing. Product Finish: Rousseau's powder coating system gives our products a lasting, high-quality finish. This coating has excellent resistance to corrosion and chemicals. Also, it has outstanding mechanical properties (hardness, adhesion, flexibility, resistance to abrasion and impacts). Our powder coating provides a uniform finish free from the surplus, striations, and drips that are usually found in conventional liquid-paint systems. Powder paint also enables a thicker layer to be applied compared with a standard liquid-paint system. The electrostatic application of this powder coating means that a good thickness of paint is obtained on the edges, which eliminates the sharp edges that are generally found on products fabricated from sheet metal. Our powder-painting process creates very little or no air pollution (VOC). Further, the excess powder paint created when spraying is recycled, practically eliminating all the losses usually found in liquid finishing processes. We apply between 1.5 and 4 mils paint thickness according to the color chosen. Gloss is 45 u for our semi-gloss colors and 90 u for gloss colors. Type of Steel: Unless otherwise stated, the used is commercial quality. Contact Custom Products & Services, Inc. 1/20

LA30 Cabinet Left and Right sides Back Top 20 gauge Has 2 circular knock-outs on upper housing for anchoring cabinets side-by-side or for installation of RB90 side handle. Has 2 knock-outs at bottom of the housing to install WS23 footrest. Has 2 circular knock-outs at the bottom of housing for anchoring cabinets side-by-side. Front posts are folded towards the sides of housing and spot welded in place. Posts are perforated for installation of drawer slides, shelves and doors. Assembled to the top, back and bottom by spot welding. Part folded on each side to form the back posts of the cabinet. Has 2 circular perforations at the top and 2 at the bottom for anchoring 2 cabinets back-to-back. Equipped with perforations at the top allowing for assembly and maintaining the locking guide in place. Top, bottom and side assembly by spot welding. Formed with single folds at the back and sides and a double fold on the front. Equipped with 2 circular knock-outs on the side folds for anchoring cabinets side-by-side or installing the RB90 side handle. Equipped with 2 circular knock-outs on the back fold for anchoring 2 cabinets back-to-back. 8 perforations on the top for attaching directly to under the work surface. Assembled to the back and sides by spot welding. Can be used: as a base for attaching a work surface, suspended under the work surface, installed on a cart or base for casters for mobile applications or inserted under a table top. Offered in a multitude of configurations: with LF31 drawers, LB30 doors, LB24 shelves, handles and different locking options. Locking system includes choice of lock: o L3: Customized nickel-plated aluminum lock with key. Features 1000 codes. Three types of key are available: identical keys (KA), different keys (KD) and master key system (MK). o LP: Nickel plated aluminum lock for use with padlocks of max. 8 mm rod diameter. o L50: Electronic lock in metallicgray painted aluminum with customizable combinations. Features 19 user codes and one code for supervisor of 4 to 8 characters. Three management options are available: "owner" mode with single code, supervisor + users with common code, supervisor + users with different codes. Bottom designed to also be used as a shelf. Possible to anchor cabinets sideby-side, back-to-back and stacked on top of each other. Possible to stack cabinets with the use of LA78 stacking kit. ESD options available: a grounding cord and a ground wrist strap. The width, depth and height of the dimensions are exact, which facilitates layout changes. 18'' wide housing measures exactly 18''. Can be used with Cabinet Attachment Bars RA70 to attach the cabinet under the work surface without having to remove the drawers. See W54 technical document for capacity chart Width: 18" Depths: 21", 27" Height: nominal dim. Inside width: 16 1/8" Inside Heights (for drawers): nominal dim. 4" Contact Custom Products & Services, Inc. 2/20

Note: The Bars are required to attach a 21'' deep cabinet with Steel Top WS10/12 or a 27'' deep cabinet with Steel Top WS10/12. LA72 Four top reinforcers 14 galvanized Washers used for reinforcement when screwing on a cabinet with wood work surface WS14. Use the screws supplied with the cabinets. Reduces the twisting effects of wood due to humidity. Diameter 2'' Thickness: 0.074'' LA74 Leveling Glides Kit 14 galvanized Zinc-plated glides with nylon sole. Comprised of 2 ''U'' shaped parts. Space provided for anchoring cabinets back-to-back and for the locking mechanism. Has 3/8''-16 clinch nuts for assembling levelling glides. Installed under cabinets with rivets (when factory installed) or with screws (when installed by user) (4 per part). Installed under cabinets with or without bases. Allows user to adjust leveling glides with key from underneath the cabinet without having to take drawers out. Allows for user to adjust housing height from 27/32'' to 1 13/16" from the floor. 650 lb Width: 17 3/8" Depth: 3 11/16" Height: 1 3/4" LA76 Floor Anchor Hardware Kit 14 galvanized Comprised of 1 part folded in a ''L'' shape. Space provided for back-to-back anchoring of cabinets and for the locking mechanism. Installed under the cabinet and held in place by two tabs that are then folded towards the bottom of the cabinet. Includes floor anchoring hardware for concrete floors: bolts 3/8''-16 dia. X 3'' L, washers and 3/8-16'' nuts. Largeur: 17 3/8" Profondeur: 3 11/16" Hauteur: 1 3/4" LA77 Floor Anchor Hardware Kit 12 galvanized Includes 1 part with two 90 folds. Secured underneath an LA87 or LA88 base with two 5/16"-18 bolts and screws. Includes floor anchoring bolts for concrete: 3/8''-16 x 3" bolts, washers and 3/8''-16'' screws. For anchoring with LA87 or LA88 bases. Width: 15 3/4" Depth: 1 ¼ " Height: 1 7/8" LA78 Stacking Kit 14 galvanized Comprised of 2 parts folded in a ''L'' shape. Space provided for back-to-back anchoring of cabinets and for the locking mechanism. Installed under the cabinet and held in place by two tabs that are then folded towards the bottom of Witdh: 17 3/8" Depth: 3 11/16" Height: 1 3/4" Contact Custom Products & Services, Inc. 3/20

the cabinet. Includes 5/16''-18 clinch nuts to facilitate anchoring. Includes 5/16''-18 x ¾'' bolts and washers. LA85 Cabinet Base 20 gauge Comprised of 2 ''L'' fold parts that are welded together in order to form the base. Single folds at the top and bottom serve to make the part more rigid. Installed under cabinets with screws (installed by user). Allows user to raise height of cabinet by 2 & 4''. Recessed from front of cabinet by 2'' to leave room for feet. Base can be installed with recessed portion at the front or at the back of the cabinet. Compatible with leveling glide kit LA74 which allows cabinet height with base to be adjusted from 27/32'' to 1 13/16" from the floor. See W54 technical document for capacity chart 21"D Cabinet: Width: 17 7/8" Depth: 18 7/8" 27"D Cabinet: Width: 17 7/8" Depth: 24 7/8" Height: 2 & 4" LA87 Workstation Base Cabinet Base Left/Right Cross member front/rear 14 gauge 14 gauge Part formed from three 90 folds and one angled fold including inserts for adding leveling glides. Secured to the cabinet with bolts. Interior space provided for insertion of forklift or pallet truck forks. An RK68/69 kick plate can be added at the front or back. Part formed from four 90 folds. Welded to the left and right of base. Includes openings for adjusting leveling glides or anchoring (optional) from inside the LA30 cabinet. Includes a 2" opening at the front of the cabinet for working close to the cabinet (room for feet). Compatible with all RA75 leveling glides so height of the cabinet with base can be adjusted from 27/32'' to 1 13/16" from the ground. Can be anchored to the floor with optional LA77 kit. See W54 technical document for capacity chart 21" deep cabinet: Width: 18" Depth: 18 7/8" 27" deep cabinet: Width: 18" Depth: 24 7/8" Height: 4" LA88 Workstation Stainless Steel Base Cabinet (see also base cabinet LA87) Base Left/Right Cross member front/rear 14-gauge stainless (#4 brushed finish) 14-gauge stainless (#4 brushed finish) See LA87 See LA87 See W54 technical document for capacity chart See LA87 See LA87 LB00 Cabinet Locking Mechanism with Lock Locking bar Lockin rods 16 galvanized Steel round polished rod ¼" dia. Allows all drawers to be locked with a single lock. "C" shaped part has perforations at every 1" c/c in height in order to lock the drawers by a transferring up and down movement from the action of the lock. Inserted in the bottom of the cabinet with the lower legs and in the locking bar guide on top. Makes a link between the lock and the locking bar to change the rotating movement to a transferring movement of the locking bar. Allows repositioning of the drawers in the cabinet without having to move or take off the locking mechansim. The lock installs on the housing without hardware or tools. Is easy for the client to install. Locks available: o L3: Customized nickel-plated Depends on the height and depth of the cabinet. Contact Custom Products & Services, Inc. 4/20

Locking bar guide 14 galvanized Has a crushed tip with a hole to fasten to the locking rod with a plastic clip. Has shifted folding at the other extremity. ''C" shaped part with perforations for guiding the locking bar and lock rod. Equipped with an adapter that is clipped in the locking guide and in which the locking rod is inserted. Has perforations for anchoring cabinets back-to-back even after the mechanism has been put in place. Inserted at the upper portion of the back posts on the cabinet. Has a movable tab at each end for keeping the guide in place in the perforations in the posts. aluminum lock with key. Three types of key are available: identical keys (KA), different keys (KD) and master key system (MK). o LP: Nickel plated aluminum lock for use with padlocks of max. 8 mm rod diameter. o L50: Electronic lock in metallicgray painted aluminum with customizable combinations. Features 19 user codes and one code for supervisor of 4 to 8 characters. Three management options are available: "owner" mode with single code, supervisor + users with common code, supervisor + users with different codes. LB10 Vertical Security Bar 16 gauge Formed by fold and is equipped with perforations to attach by screwing to the front right facing of LA30 cabinets. Has a perforation to use a lock. The shape of the bar matches the shape of the edges of the RF31 drawer handle. Has 2 fasteners to keep the bar in place. Fasteners are galvanized and equipped with riveted nuts. Dimensions available for every cabinet height. Choice of locks: L3: Customized nickel-plated aluminum lock with key and lockbolt. Features 1000 codes. Three types of key are available: identical keys (KA), different keys (KD) and master key system (MK). LP: Nickel plated aluminum lock for use with padlocks of max. 8 mm rod diameter. 200 lb in traction. Width: 1 13/16'' Depth: 1 13/16'' dim 4 1/8'' LB24 Adjustable Galvanized Light-Duty Shelf (cabinet) Shelf Rails 20 galvanized 18 galvanized Part made more rigid by folds in an upward direction at 90, 5/8'' thick on 3 sides and 5/8'' on the front. Double fold toward the inside on the front face. Perforations on the sides for screwing on the rails. 2 ''L'' folded parts that are inserted by hooking them onto the perforations in the front and back posts of the cabinet. Held in place with tapping screws. Height adjustments at every 1" c/c. 2 positions: When installed behind an integrated door LB30. Advanced without integrated doors LB30. Two versions available: version 01 when used with locking mechanism LB00 and version 02 when used without locking mechanism LB00. 100 lb Width: 15 15/16" Depths: 01 version = nominal dim. 2 ½'' (with locking mechanism LB00) 02 version = nominal dim. 1 ½'' (without locking mechanism LB00) Contact Custom Products & Services, Inc. 5/20

LB30 Integrated Door Door Stopper 20 gauge 22 galvanized Has a double fold on the side with the handle and single folds at the top and bottom to make the panel more rigid. Has a reinforced fold on the side with the hinges. It is then assembled by welding it to the inside face of the door. Perforations for inserting the nylon injected handle. Equipped with two 19 gauge hinges welded to the door and to the housing with rivets. Serves as a stop for the door and the lock Has 2 hooks and is held in place with rivets. Opens 180. Can be integrated in a cabinet with with drawers on top, underneath or full height. Possible to use with an adjustable cabinet shelf behind the door. Reversible for left or right opening. Protects the contents of the cabinet from dust and theft. Choice of locks: o L3: Customized nickel-plated aluminum lock with key and lockbolt. Features 1000 codes. Three types of key are available: identical keys (KA), different keys (KD) and master key system (MK). o LP: Nickel plated aluminum lock for use with padlocks of max. 8 mm rod diameter. Width: 16 3/8" Depth: 5/8" dim. 1/4" LB81 4" Casters Caster: Core made of polyamide with a polyurethane coating. Thick /zinc plated Caster made of polyamide and covered with grey, nonskid, non-marking polyurethane (55 Shore D). Equipped with a roller bearing. Swivel caster mounted on a ''double way'' ball bearing rolling system. Resistant to temperatures between -40 C and +80 C. Lubricated with long life grease. Steel plate with 4 holes for installation allows casters to be installed at the side or front / back. Installation plate measures 4" x 4 1/2" with 4 holes for installation. 3 types of casters available: rigid, swivel and swivel with total brake (on wheel and swivel). Quiet operation, resistant to shocks, vibrations, corrosion & a wide variety of chemical products. 420 lb / caster Caster diameter: 3 15/16" Total height: 5 1/8'' LB84 6" Casters Caster: Core made of polyolefin with a polyurethane coating ¼" zinc plated Caster made of polyolefin and covered with grey, nonskid, non-marking polyurethane (55 Shore D). Equipped with a roller bearing that can be lubricated. Swivel caster mounted on a ''double way'' ball bearing rolling system. Steel plate with 4 holes for installation allows casters to be installed at the side or front / back. Installation plate measures 4" x 4 1/2" with 4 holes for installation. 3 types of casters available: rigid, swivel and swivel with total brake (on wheel and swivel). Quiet operation, resistant to shocks, vibrations, corrosion & a wide variety of chemical products. 900 lbs. / caster Caster diameter: 5 15/16" Total height: 7 3/8" LB85 6" MAG Casters Caster: Core made of aluminum with a polyurethane coating Caster: Core is nickel (brassnickel) plated. ¼" zinc plated Casters made of aluminum and covered with black non-marking polyurethane (70 Shore D). Equipped with a roller bearing that can be lubricated. Equipped with a roller bearing that can be lubricated. Swivel caster mounted on a ''double way'' ball bearing rolling system. Steel plate with 4 holes for installation allows casters to be installed at the side or front / back. Installation plate measures 4" x 4 1/2" with 4 holes for installation. 3 types of casters available: rigid, swivel and swivel with total brake (on wheel and swivel). Quiet operation, resistant to shocks, vibrations, corrosion & a wide variety of chemical products. Caster with aesthetic design like car wheel. 1000 lbs. / caster Caster diameter: 6" Total height: 7 1/2" Contact Custom Products & Services, Inc. 6/20

LB8C 4'' Casters 4'' Casters Caster: Core made of aluminium with a Besthane Soft polyurethane coating. Thick /zinc plated (without Cr6) Caster made of aluminium and covered with blue, nonskid, non-marking polyurethane (75 Shore A). Equipped with a ball bearing. Swivel caster mounted on a ''double way'' ball bearing rolling system. Resistant to temperatures 25 C & +70 C. Steel plate with 4 holes for installation allows casters to be installed at the side or front / back. Plate measures 4" x 4 ½". 2 types of casters available: rigid, and swivel with total brake (on wheel and swivel). Quieter operation and less rolling resistance than LB81. Protects floors, highly durable, highly resistant to cuts and tearing, very good chemical bond with the wheel body. 660 lb / caster Caster diameter: 3 15/16" Total height: 5 1/8'' LB8D 6'' Casters 4'' Casters Caster: Core made of aluminium with a Besthane Soft polyurethane coating. Thick /zinc plated (without Cr6) Caster made of aluminium and covered with blue, nonskid, non-marking polyurethane (75 Shore A). Equipped with a ball bearing. Swivel caster mounted on a ''double way'' ball bearing rolling system. Resistant to temperatures 25 C & +70 C. Steel plate with 4 holes for installation allows casters to be installed at the side or front / back. Plate measures 4" x 4 ½". 2 types of casters available: rigid, and swivel with total brake (on wheel and swivel). Quieter operation and less rolling resistance than LB81. Protects floors, highly durable, highly resistant to cuts and tearing, very good chemical bond with the wheel body. 1100 lb / caster Caster diameter: 5 15/16" Total height: 7 3/8" LB93 Cart for Mobile Cabinet Cart Cover 14 gauge Structure folded on all 4 sides. Fitted with perforations on the 4 corners in order to attach LB81 4'' or LB84 6'' casters or LB85 6'' mag casters. Additional perforations to screw the cart to LA30 cabinet. Part formed with a double fold at a 45 angle to cover part of the front of the cart. Attaches to the cart with screws. Installs on cabinets without base. Cart for single mobile cabinet only. + 1/8" dim. + 2 9/16" Height: 2 1/16" LB96 Heavy-duty Base for Casters 12 galvanized Folded ''U'' shaped part. Has 3/8''-16 clinch nuts for installing LB81 4'' casters, LB84 6'' casters or 6'' LB85 MAG casters. Has an offset fold which is inserted under the bottom fold of the housing. Attached at the front and back under the housing at the same time the casters are installed. Installed under the cabinet housing with no base. For mobile applications with double or triple cabinets or for a cabinet with a workstation. Width: 17 1/2'' Depths: 5" Height: 1 13/16" LB97 Base for Casters 14 galvanized Folded ''U'' shaped part. Has 3/8''-16 clinch nuts for installing LB81 4'' casters, LB84 6'' casters or 6'' LB85 MAG casters. Has an offset fold at each end which are inserted under the bottom fold of the housing. Attached at the front and back under the housing at the same time the casters are installed. Installed under the cabinet housing with no base. For mobile applications with double or triple cabinets or for a cabinet with a workstation. Width: 4 15/16'' Depths: 20 1/8", 26 1/8'' Height: 1 13/16" Contact Custom Products & Services, Inc. 7/20

LC50 Grounding ESD Kit (see also grounding cord 70000300) Grounding Cord With 1 MΩ resistance 70000300 See 70000300 See 70000300 See 70000300 and details below: Relays the cabinet to the ground. See 70000300 70000300 Wrist strap socket 70000400 Black Socket installed on the cabinet to allow grounding cord to be plugged into the cabinet. Relays the cabinet to the ground by using grounding cord. Dissipates charges that risk to damage electronic components. LD75 Drawer Unit Upper crossbars on front of unit Lower crossbars on front of unit Sides Back 18-gauge Folded ''U'' shaped parts that are welded to the sides. 2 tear drop perforations and 2 circular perforations 9/32'' in diameter on the upper fold for installing unit under a work surface. 2 circular perforations 3/8'' in diameter on the upper fold for bolting two stacked units together. Part is folded in a ''U'' shape and is welded to the side pieces. 2 tear drop perforations on lower fold for installing on top of a work surface. 2 circular perforations on lower fold for bolting unit with a unit below or a unit stacked on a LA30 cabinet. Has 2 circular upper and lower knock-outs for anchoring two drawer units side-by-side. Has a 90 fold at the bottom. Has an offset fold at the top to avoid interference with WS20 or WS25 legs. Back portion is folded towards the back of the unit. Includes front posts which are folded onto the sides of the drawer unit. Once folded, the posts are held in place by spot welding. Posts are perforated for installation of drawer slides. Back and crossbar assembly by spot welding. Folded on each side in order to form the back posts of the housing. Has 2 tear drop shaped perforations on the upper fold for attaching the unit under a work surface. Has 2 tear drop shaped perforations on the lower fold for attaching the unit on top of a work surface. Has 2 circular perforations on the lower fold for bolting with another drawer unit below or stacking on top of LA30 cabinet. Spot welded to side components. Assembly: Holes in shape of tear drops = possible to pre-screw under or on the work surface before installing the unit. Can be fitted with a 3", 4'', 5'', 6", 8"& 12"drawer. Possible to lock drawers by adding a HA51 lock to each drawer. Compatible with lock-in drawer. Can be used both above or below the work surface. LD76 cover to close the top is available when used above the work surface. Possible to stack several units. Possible to place side-by-side with a WS20/25 leg without a gap between the unit and the leg. Suspended under the work surface: -50 lb / drawer (for a workstation not anchored to the floor) -100 lb / drawer (workstation anchored to the floor). -175 lb / unit (or for 2 stacked units). Placed on a work surface (and anchored): -100 lb / drawer Width: 18" Depths: 21", 27'' Outside heights (inside): 9" (6"), 12" (9"), 15" (12") LD76 Drawer Unit Top 18-gauge Part has a 90 fold on all four sides which makes the cover more rigid and fills the space left by the offset fold on the sides of the LD75 drawer unit. Equipped with two threaded and riveted inserts which allow for assembly with the drawer unit. Finishing piece when the unit is used above the work surface. Width: 18" Depths: 21 1/8", 27 1/8" Heights: ½'' Contact Custom Products & Services, Inc. 8/20

LD77 Drawer Unit Upper crossbars on front of unit Lower crossbars, bottom & back Sides Folded ''U'' shaped parts that are welded to the sides. 2 tear drop perforations and 2 circular perforations 9/32'' in diameter on the upper fold for installing unit under a work surface. 90 degree double fold which forms the bottom, the back and front crossbar. Has 90 degree bends on the sides for assembly via spot welding to the left and right sides. Has 2 tear drop perforations on the upper fold at the back for assembly under the work surface. Has 4 perforations (at each corner) under the part in order to provide enough room for the use of a tool to assemble under a workstation. Has a 90 degree bend at the top and a series of bends at the front to form the housing posts. Has a perforation at the front on the posts in order to hook the drawer slides in and for the lock-in mechanism and individual drawer lock. Has 2 oblong holes in the upper bend for bolting under the work surface. Assembly: Holes in shape of tear drops = possible to pre-screw under or on the work surface before installing the unit. Can be fitted with a 3" & 4'' drawer. Possible to lock drawers by adding a HA51 lock to each drawer. Compatible with lock-in drawer. Possible to place side-by-side with a WS20/25 leg without a gap between the unit and the leg. Suspended under the work surface: -50 lb / drawer (workstation not anchored ot the floor) -100 lb / drawer (work station anchored to the floor) -175 lb / unit (or for 2 stacked units). Width: 18" Depths: 21", 27'' Outside heights (inside): 6" (3"), 7" (4") LD85 Cabinet for Sink (see also cabinet LA30) See LA30 See LA30 and details below: Top and back equipped with holes in order to install under a counter with sink: Top perforation: o Width : 14'' o Depth : 18'' Back perforation: o Width : 11 7/8'' o Heights : nominal height housing 6 1/16'' See LA30 Width: 18" Depth: 27" dim. nominal Inside width: 16 1/8" LF31 Drawers 3, 4, 5, 6 & 8" Front Has a knock-out on the right side for inserting an optional lock. Has a rectangular perforation on the right for inserting the optional LY02 lock-in mechanism. Has round holes for assembling the aluminum handle with tapping screws. Welded to the body of the drawer. Body 20 gauge Part folded at 90 to form the bottom and the sides of Compatible with drawer units LD75 and cabinets LA30. Open 100%. Optimizes space and limits loss of space in storage. Handle with identification zone to identify drawer contents. Many drawer accessories are 100 lb capacity per drawer when used in the cabinet Width: 16 7/16'' dim. 1 21/32'' dim. 7/64" Inside dimensions: Width: 14 19/32" Contact Custom Products & Services, Inc. 9/20

21 & 27'' Drawer Slides Handle Endcaps 16 gauge Zinc plated 6063-T5 aluminum extrusion Naturally anodized Polyurethane (PP) Black, blue, orange the drawer. Equipped with embossed sections with slots for inserting partitions and clipping dividers. Has a 7/16'' fold formed on the upper part to reinforce the panels. Has circular perforations at the bottom of the drawer to help keep partitions in place with the help of tapping screws. Has rectangular perforations and small circular embossing for inserting and locking the hooks on the slides in place. Consists of 3 slides each inserted into the other. Equipped with polyurethane shock absorbers. Steel ball rolling system. Profile attached to the front of the drawer with a screw. Front face tilted for label holder. available: partitions, dividers, plastic bins, foam for toals, etc. Possibility to lock all the drawers with the cabinet central locking system LB00. Possible to add individual HA51- L3 drawer lock: Customized nickel-plated aluminum lock with key and lockbolt. Features 1000 codes. Three types of key are available: identical keys (KA), different keys (KD) and master key system (MK). Tilt allows fast identification of information on the label. Full-width identification. LF70 handle protector offered as an option. dim. 3 3/8'' dim. 29/32" Width: 1 5/8" Depth: 3/4" Height: 2 5/16" LF31 Drawer 12" (see also drawer LF31 3, 4, 5, 6 & 8'') Front See LF31 3, 4, 5, 6 & 8'' Body See LF31 3, 4, 5, 6 & 8'' Combing Back 20 gauge 20 gauge Slides See LF31 3, 4, 5, 6 & 8'' See LF31 3, 4, 5, 6 & 8'' See LF31 3, 4, 5, 6 & 8'' and details below: Includes the bottom and the sides. Folds at the front and back for spot welding with the front and back panels of the unit. Front fold includes the embossing at the bottom with slots for inserting and clipping partitions. Sides formed with folds that are 1 1/8'' towards the outside of the drawer, which is then refolded at 90 to the outside with a width of 3/8'', this is done to make the body of the unit more rigid. Perforations on the sides to insert LG31 hanging file bars. Part is spot welded on the inside facade of the front panel at the top. Part spans the inside width of the drawer and is 2'' high. Equipped with embossed sections with slots for inserting and clipping partitions. Has circular perforations in order to relieve the hole and the front for an optional lock. Folded 1 1/8'' towards the outside of the drawer to reinforce the part. Part spot welded to the body of the drawer. Equipped with embossed sections at the top and bottom with slots for inserting and slipping partitions. See LF31 3, 4, 5, 6 & 8'' See LF31 3, 4, 5, 6 & 8'' and details below: Width designed for legal size hanging files (8 ½'' x 14''). For letter size (8 ½'' x 11) add LG31 Hanging File Bars. See LF31 3, 4, 5, 6 & 8''. Width: 16 7/16'' dim. 1 21/32'' Height: 11 7/8" Inside dimensions: Width: 14 19/32" dim. 3 3/8'' dim. 29/32" Contact Custom Products & Services, Inc. 10/20

Handle See LF31 3, 4, 5, 6 & 8'' Endcaps See LF31 3, 4, 5, 6 & 8'' See LF31 3, 4, 5, 6 & 8'' See LF31 3, 4, 5, 6 & 8'' See LF31 3, 4, 5, 6 & 8'' See LF31 3, 4, 5, 6 & 8'' LF44 Roll-Out Shelf (see also drawer LF31) Front Body 20 gauge Includes a rectangular perforation on the right for inserting an LY02 lock-in mechanism (optional). Includes round holes for securing the aluminum handle with tapping screws. Welded to the drawer body. Part with 90 downward folds on the sides creating the inverted bottom. 90 fold at the back for reinforcement and to prevent items from falling. Includes an offset fold at the front and top to provide space for the handle. U-profile fold welded to the back of the drawer for reinforcement. Voir LF31 An LY02 lock-in mechanism can be added (optional). 100 lb capacity per shelf when used in the cabinet Useable dimensions: Width: 14 13/16" dim. 3 3/16'' Height: 3 7/8'' Back 21 & 27'' See LF31 Drawer Slides Handle See LF31 Voir LF31 Voir LF31 Voir LF31 Endcaps See LF31 LF70 Plastic Handle Protector Synthetic PVC Translucent color Simple shape, equipped with details on the extremities that permits clipping onto the handle. ¾ " identification zone at the top. Clips directly onto the handle without tools. Resists splatters, cleaning products and light solvents. 2 1/32" LF71 Handle Labels White cardboard Each kit includes 10 cardboards with 22 labels per carboard that can be separated. 8 ½'' X 11'' printable format (with almost any inkjet & laser printer) Electronic label template can be downloaded from rousseau's website. Labels are designed to be used under the Handle Protector RF70. Cardboard: Width: 8 ½'' Height: 11'' Labels: Width: 4 ¼'' Height: 0.733'' LF91 Galvanized Security Panel 20 galvanized Serves to block access between two drawers. Has a double fold at the front and at the back of the panel for rigidity. Has folds on the two sides. Back portion is inserted discretely into the perforations on the back posts of the housing. Has perforated tabs at the front and the sides for Installs between 2 drawers without causing any loss of space within the drawers as the sides of the drawers can be full height and they are not reduced to have a panel installed inside. Two versions available: Contact Custom Products & Services, Inc. 11/20 Width: 17 5/8'' Depths: 01 version: nominal dim. 3'' (with locking mechanism LB00)

blocking the panel in place and inserting tapping screws. o Version 01: When used with locking mechanism LB00; o Version 02: When used without locking mechanism LB00. 02 version: nominal dim. 1 7/8'' (without locking mechanism LB00) Height: 7/16" LG02 Galvanized Front to Back Partition 18 galvanized Part formed at 90 o at the bottom with oblong perforations to screw to the bottom of the drawers. Inserts into the combing at the sides, back, and front of LF31 drawers. The combing is formed with the partitions and has connection slots that attach the partitions in place. Has 2 sets of combing in height except for the the 3'' high. Holes at every 3" center to center. Partition for the 27'' deep drawer has additional perforations to allow for making 3 equal compartments. Divides the drawer along its width. Accepts RG10 dividers to redefine the space between each partition. Compatible with the following accessories: RG20/21 plastic bins, RG35/36 groove trays and RG40 PVC drawer liners. 3 1/8" dim. 1 3/8'' Depth: 5/8'' LG31 Hanging File Bars (Left to Right) 12 gauge Formed in a "L" for rigidity. Equipped with a cut-out at each extremity in order to be installed in the sides of the LF31 12''H drawer. Designed to store hanging files from left to right. Width: 15 ½'' Height: 1 ¼" Depth: 3/8" LG40 PVC Drawer Liner Resin P.V.C. Black color 1/16'' Thick. Is cut to fit the format of the drawer into which it is inserted. Allows for protection of stored items and prevents them from moving when drawer is opened and closed. Possible to screw partitions on the surface. Oil resistant. Witdh: 14 ¾" dim. - 3 ¼" Thickness: 3/32'' LG41 Foam for Protection Resin P.E. Blue color 4 lb density. ¼'' Thick. Closed-cell, crosslinked, polyethylene foam. Oil resistant Good chemical resistance. Water resistance. Good ultraviolet stability. Non-absorbant. Does not leave blowing agent residues in the foam. Witdh: 14 ½" dim. - 3 ½" Thickness: 1/4'' LG42 Foam for Tools Resin PE/EVA Black color (top) and blue (bottom) Blue foam is 4 lb density & ¼ '' thick. Self adhesive black foam is 6 lb density & ½'' thick. Closed-cell, crosslinked, polyethylene foam. See LG41 and details below: The blue foam allows for fast retrieval of tools due to the color contrast. See LG41 and details below: Witdh: 14 ½" dim. - 3 ½" Thickness: 1/2'' Contact Custom Products & Services, Inc. 12/20

LG49 Non-skid PVC Drawer Liner Resin PVC Black color 1/16'' Thick Is cut to fit the format of the drawer into which it is inserted. Reinforced PVC liner with polyester fabric. Not compatible with partitions. Allows for protection of stored items and prevents them from moving when drawer is opened and closed. Non-skid material Reversible. Oil resistant. Witdh: 14 ¾" dim. - 3 ¼" Thickness: 1/16'' LY00 Left Endcap Resin polypropylene copolymer Colors: blue, black, orange The endcap is inserted into the extrusion. Clipped in place on the front of the drawer and screwed into place at the same time as the extruded aluminum handle. LY01 Right Endcap (see also endcap LY00) See LY00 See LY00 Design is different from the left endcap in order to accommodate the lock-in mechanism. LY02 Lock-in Resin acetal (homopolymer) Comprised of 3 parts, a catch with molded handle, a compression spring for security and a stopper for the spring. Left end of the catch has the activation handle that directly controls the action of the catch then moved right to left. The lock-in is inserted and clipped into the right endcap and slides into the extrusion in the handle. Mechanism can be retro-fit easy installation. LY05 Fixed Handle Natural anodic aluminum 6063-T5 Profile attached to the front of the drawer with a screw. Front face tilted for label holder. Tilt allows fast identification of information on the label. Full-width identification. 200 lb horizontal traction on the drawer. Identification surface: 3/4'' H LY07 Fixed Handle with Endcaps (see also endcap LY00, LY01 and fixed See LY00 / LY01 / LY05 See LY00 / LY01 / LY05 See LY00 / LY01 / LY05 See LY00 / LY01 / LY05 See LY00 / LY01 / LY05 Contact Custom Products & Services, Inc. 13/20

handle LY05) HA49-LP ''L'' Door Lock Lock Nickel plated Rotates 90. Installs in the Rousseau handle. For lock with a rod 8 mm in diameter (maximum). Cam Stopper (not illustrated) 12 galvanized 22 galvanized Rounded ends for security. Cam has offset. Perforation for assembly and control of the lock. Part 6'' high with several folds to keep the door closed. The cam on the lock leans against the stopper to keep the door from opening when locked. Exterior dia.: 27/32" HA49-L3 Serrure de porte L Lock Nickel plated Machined brass key with nickel finish. Rotates 90. Installed in the Rousseau handle. Cam Stopper (not illustrated) 12 galvanized 22 galvanized Rounded edges for safety. Cam has offset. Perforation for assembly with and control of the lock. 6 high part equipped with several folds for keeping the door closed. The cam on the lock leans against the stopper to keep the door from opening when locked. Features 1000 codes. Three types of key are available: identical keys (KA), different keys (KD) and master key system (MK). Exterior dia.: ⅞" HA51 ''L'' Drawer Lock L3 Lock Nickel plated Machined brass key with nickel finish. Rotates 90. Equipped with a spring clip to keep lock in place. Cam Box Cover Camreinforcement 12 galvanized 16 galvanized 16 galvanized 16 galvanized Rounded edges for safety. Cam has offset. Perforation for assembly with and control of the lock. Part has a 90 fold to house the lock, keep the cover in place and guide the catch. Held in place to the front of the drawer by the lock, spring clip and two adhesive strips on the back of the lock box. Part has a 90 fold to house the lock and guide the catch. Attached to the lock box with a tapping screw. Small part with structural folds, attached to the side of the drawer and supports the cam. Attached to the drawer with pop rivets. Features 1000 codes. Three types of key are available: identical keys (KA), different keys (KD) and master key system (MK). Lock exterior dia.: ⅞" Box and cover dimensions Width: 2 11/16" Height: 1 13/16" Depth: 1 5/32'' RA70 Cabinet Attachment Bars 14 gauge Constructed of 2 "L" shaped parts that attach to the knockouts on the sides of the housing LA30 with hooks. Has holes on the top facing to screw the housing under a work surface. Allows user to attach a cabinet under the work surface without having to take the drawers out. Note: The Cabinet Attachment Bars RA70 are absolutly required with Steel Top WS10/12 when the See W54 technical document for capacity chart Width: 1 ¼" Height: 1 ¼" Depths: nominal dim. ¼" Contact Custom Products & Services, Inc. 14/20

cabinet is installed at 1 ½'' from the side of the workstation. The Bars are also required to attach a 21'' deep cabinet with Steel Top WS10/12 or a 27'' deep cabinet with Steel Top WS10/12. RB90 Side Handle (Sides) Black polypropylene (end cap) Anodized aluminum 6061-T6 (handle) End caps are injection molded and inserted into the interior of the aluminum tube. End caps are designed with over molding on the bolts that allow for assembly to the heavy-duty housing. Leaves 1 ¾'' space from the cabinet. Diameter of aluminum tube: 1 1/8''. Good resistance to lateral shocks. Height: 1 ¾'' Width: 2 ¾'' Depths: nominal dim.- 6 ¼'' RB92 Front Handles (Front) Nylon (PA) reinforced fibreglass Installs by bolting to the front of the cabinet. Offers a solid grip at the front of the cabinet for better control when moving. Resistant to solvents, oil, grease and other chemical agents. Width: 5¼" Depth: 1" Height: 1⅝" RB97 Bumpers for Cabinet Grey PVC L-shape protective corners. For installation with 3/16" rivets. Protect the corners of the cabinet from impacts. Width: 4" X 4" Height: 1" RC32 Steel Top with Rubber Mat 14 gauge painted Work surface for cabinet tops. Equipped with a black neoprene mat. Has 90 o folds of 1" on 3 faces and welded in the corners to prevent objects from falling. Has countersink holes to attach to the top of the housing by bolting. Has a fold at the front to protect the front edge of the cabinet. The surface of the top is even with the top of the cabinet. This allows housing to be anchored together without interference. Compatible with doors with frame and side housing depending on dimension. dim. Contact Custom Products & Services, Inc. 15/20

RC35-XXXX Stainless Steel Top 16ga 16 gauge stainless (#4 brushed finish) (top) Wood composite panel 1 5/8'' thick (interior) Top has four 90 o bends toward the base. The front fold has another 9/16'' fold toward the interior so that the back edge will not be sharp when the upper side exceeds the front housing. The return keeps the wood composite in place. The corners are welded and polished for an esthetic finish. Particle board in conformity with CARB-1 legislation (level of formaldehyde emission and other provisions) dim. Height: 1 ¾'' RC35-XXXX-16M Stainless Steel Top 16ga + Marine Edge (see also stainless top 16ga RC35-XXXX) See RC35-XXXX See RC35-XXXX and details below: Front has a marine edge 1 5/8'' deep x 3/16'' high. Marine edge is a spill proof feature for hardware or liquids. See RC35-XXXX See RC35-XXXX RC35-XXXX-12 Stainless Steel Top 12ga (see also stainless top 16ga RC35-XXXX) 12 gauge stainless (#4 brushed finish) (top) Wood composite panel 1 5/8'' thick (interior) See RC35-XXXX See RC35-XXXX and detail below: High impact resistance See RC35-XXXX RC35-XXXX-12M Stainless Steel Top 12ga + Marine Edge (see also stainless top 16ga RC35-XXXX and 12ga RC35-XXXX-12) See RC35-XXXX-12 See RC35-XXXX-12 and details below: Front has a marine edge 1 5/8'' deep x 3/16'' high. Marine edge is a spill proof feature for hardware or liquids. See RC35-XXXX-12 See RC35-XXXX RC36 Galvanized Steel Top (see also stainless top 16ga RC35-XXXX) 16 gauge galvanized (top) Wood composite panel 1 5/8'' thick (interior) See RC35-XXXX and detail below: The corners are not welded and polished. See RC35-XXXX See RC35-XXXX Contact Custom Products & Services, Inc. 16/20

RC37 Painted Steel Top (see also stainless top 16ga RC35-XXXX) 16 gauge (top) Painted Steel Wood composite panel 1 5/8'' thick (interior) See RC35-XXXX and detail below: Has a hole to attach to WS stop. See RC35-XXXX See RC35-XXXX RG10 Drawer Divider 20 gauge galvanized The corners are rounded 1/8" dia. Has a 45 fold at the top. Adjustable every ½" center to center with dividers and 1" around the drawer. Inserts into side back and front combing of the drawer and the partitions. Has embossing on each side allowing a connection with the combing and holds it in place. For certain dimensions, a 5/8" fold is added to the base to reinforce the divider. An opening is left in the lower corners for a screw to hold the partitions in place. Possible to attach labels for product identification on upper inclined part. The upper fold permits fast identification and makes labels easier to read. 0.089" dim. 1 3/32" Identification zone: 3/8'' RG20 Plastic Bins RG22 RG24 RG20 RG22 Resin polypropylene copolymer Blue color Sides inclined 5 towards the outside with supplementary space for combing RG00 / RG01. Identification zone is raised and is angled at 40 complete width of the bin. Rounded base to facilitate the grip and has 4 points of support to accentuate the stability. Installation zones at the back to hook onto WM28 or WM55 panels. 6 different formats available and modular dimensions that correspond with the interior of the heavy-duty modular drawers. 1/32'' dim. 1/32'' dim. 3/32'' Identification surface: 3/8'' RG21 Conductive Plastic Bin (see also plastic bins RG20) RG23 RG25 Resin Polypropylene copolymer with conductive agent added. Black color See RG20 Has properties that avoid the accumulation of charges that can damage electronic parts. Conductive plastic. See RG20 RG21 RG23 RG22 Plastic Bin Divider Resin Polypropylene Copolymer Blue color Has rounded base for easy grip of objects. Clips on 4 points to accentuate the stability of the divider in the bin. Edge is extra thick in order to faciliate grip. Available in 4 sizes in order to repartition the bigger bins. 13/32'' dim. 3/32'' Contact Custom Products & Services, Inc. 17/20

RG23 Conductive Plastic Bin Divider Resin Polypropylene copolymer with conductive agent added. Black color See RG22 See RG22 See RG22 RG24 Plastic Bin Divider (see also plastic bin divider RG22) and See RG22 See RG22 and details below: Complete width of divider is angled at 40 serving as an identification zone. Available in 2 sizes in order to repartition the bigger bins. 3/16'' Depth: 7/16'' dim. 17/32'' Identification surface 3/8'' RG24) RG25 Conductive Plastic Bin Dividers (see also plastic bin divider RG23 and RG24) See RG23 See RG24 See RG24 See RG24 RG51 Label Holder Clear PVC Cavity holds and protects the label. Has a protective surface monted on the front on a pliable coextrusion hinge that allows it to open to replace labels. Has an angled 3/8'' fold toward the back to clip onto the drawer dividers. The fold has two small, ribbed and flexible coextrusions in order to hold the label holders well in place once clipped onto the divider. There is a small ribbed, flexible coextrusion inside the The front is ''de-clippable'' due to tabs that allow a label to be changed without taking it off. Accepts labels ½", ¾" et 7/8" in height. Widths: nominal dim Height: 1" Contact Custom Products & Services, Inc. 18/20

cavity to hold labels of very small dimensions positioned in the top of the label holder ( ½ '' high). RG52 Adhesive Label Holder (see also label holder RG51) See RG51 and details below: 3/8"double-sided adhesive foam See RG51 and details below: Adhesive back sticks at the back of the inclined surface. See RG51 See RG51 RG53 Paper Strips White cardboard Width: 2 ¾ '' Heights: ½'', ¾'', 7/8'' Thickness: 0.010" WS14 Laminated Wood Top with 90 Waterfall Front Edge May contain maple, beech &/or cherry wood Finish: sealed and varnished (semigloss) on all 6 faces Constructed with 1 ½'' to 2'' wide strips of laminated wood glued together. Thickness: 1¾". Oven-dried, top quality hardwood. Front face has 7/8'' radius. Waterfall edge for increased comfort and to reduce risk of injury. Sanded. Type of wood used ensures durability and an attractive appearance. dim. WS16 Laminated Wood Top with 90 Waterfall Front Edge Interior consisting of particle panels Finish: Laminate sheet, white matte Thickness: 1½". Front face has ¾'' rounded edge. Interior consists of particle with min. 45 lbs. density. Adhesive is water resistant. Surface and sides covered in high pressure plastic laminate. Back of the top is covered by a protective sheet. ¾'' rounded edge offers comfort and reduces risk of injury. Particle board in conformity with CARB-1 legislation (level of formaldehyde emission and other provisions). dim. 70000300 Grounding Cord 70000300 With 1 MΩ resistance 70000300 20 gauge cable Black Equipped with eyelets on both end for #10 screws. Include #10-32 nut, #10-32 wing nut, 3 lock washers, # 10 x ¾" self tapping screw and #10-32 X 2" bolt. Cable with resistance is the common grounding point (1 MΩ resistance). Relays the common grounding point to the ground. Dissipates charges that risk to damage electronic components. Cable length: 10' 70000305 Grounding Cord Without resistance 70000305 22 gauge cable Black Equipped with eyelets on both end for #10 screws. Include #10-32 nut and #10-32 X 2" bolt. Cable without resistance allows user to relay all components on the workstation to one point. Relays the shelf or the dissipative top to the grounding block or directly to the ground. Dissipates charges that risk to damage electronic components. Cable length: 6' Contact Custom Products & Services, Inc. 19/20

70000305 70000320 Ground Wrist Strap Nylon elastic 1 MΩ resistance. Includes a 5' grounding cable. Includes wrist strap socket to use with grounding block and a nylon bracelet. Adjustable bracelet. Circumference up to 9'' Length of cord: approx. 5' Contact Custom Products & Services, Inc. 20/20