Preparation Part Number: PU060-47-P Kit ontents Front Passenger Side Mudguard Front river Side Mudguard Rear Passenger Side Mudguard 4 Rear river Side Mudguard 5 Hardware Kit 6 Instruction Sheet NOTE: Part number of this accessory may not be the same as the part number shown. General pplicability ll Models Recommended Sequence of pplication Item # ccessory Hardware ag ontents 4 #0 x 0 mm Screws 4 #0 x 5mm Screws #0 Spring lips (Large) 4 #0 Spring lips (Narrow) 5 4 #0 Spring lips (Medium) 6 4 s dditional Items Required For Installation onflicts Note: Ground effects Recommended Tools Personal & Vehicle Protection None Notes Special Tools Notes None Socket/river 0mm Installation Tools Notes Screwdriver Phillips # & Screwdriver Slot Socket/river 0mm it 6mm (/4 ), 8mm (5/6 ) lean loth/rag Special hemicals Notes leaner M Prep Solvent-70 lcohol and water *Mandatory Vehicle Service Parts (may be required for reassembly) Legend STOP: amage to the vehicle may occur. o not proceed until process has been complied with. OPERTOR SFETY: Use caution to avoid risk of injury. UTION: process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MRK: This mark highlights a change in installation with respect to previous issue. SFETY TORQUE: This mark indicates that torque is related to safety. Page of 5 pages Issue: 08/0/ IO
are must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory must follow all instructions and use supplied hardware to ensure an approved quality installation.. lean Front Mounting rea 0mm Socket/river # Philips Screwdriver Slot Screwdriver (iscard) Screw Fig. - Fig. - 0mm Socket/river # Phillips/ Slot Screwdriver 0mm Screw Screw 8mm (5/6 ) it/ Spring lip (Narrow) Mudguard Screw lean and degrease front body panel where mudguard is to be located with a clean, dry lint free cloth and M Prep Solvent 70 or alcohol and water mixture. When cleaning with M Prep Solvent-70 follow the manufacturer s directions. o not allow cleaner to air dry.. Hardware Removal and Install Remove existing screws locations and. o not discard. (Fig. -). Remove existing push pin location iscard (Fig. -). Pull liner forward and install supplied spring clip (narrow) centered over location with turned up edge on inside of panel. (Fig. -). Installation of Front Mudguard Mount mudguard on body panel and install exisitng screws in location then while holding part up and into body. Install supplied 0mm screw in location while holding part tight against body. (Fig -) Fig. - While holding part in position, drill 8mm (5/6 ) hole in location. (Fig -) Install supplied push pin into location while holding part into body panel. (e) Repeat procedure for other side. Page of 5 pages Issue: 08/0/ IO
4. lean Rear Mounting rea NOTE: REMOVL N REINSTLLTION OF RER TIRE IS REQUIRE TO RILL TTHMENT HOLES. () lean and degrease rear bumper panel where mudguard is to be located with a clean, dry lint free cloth and M Prep Solvent-70 or alcohol and water mixture. () When cleaning with M TM Prep Solvent-70 follow the manufacturer s directions. o not allow cleaner to air dry. 6mm it/ 6mm it Fig. 5- (imple) (imple) 5. Identification of Rear Mount Locations Identify existing dimple hole locations and. (Fig. 5-) 6mm (/4 ) Holes in locations and, make sure to drill through panel and liner. (Fig 5-) Install supplied spring clips (medium) over panel edge holes with turned up edge on inside of panel. (Fig. 5-) Spring lips (Medium) Spring lip (Large) Indentify existing lower mount hole location and install supplied (large) spring clip center over hole with turned up edge on inside of panel. (Fig. 5-) Fig. 5- Page of 5 pages Issue: 08/0/ IO
# Phillips Screwdriver 5mm Screw 6. Installation Of Rear Mudguard Install supplied 0mm screw in location while holding part up and into bumper panel. (Fig. 6-) Fig. 6- Mudguard #0mm Screw Install supplied 5mm screws in locations and while holding part up and tightly against bumper panel. (Fig. 6-). 8mm (5/6 ) it/ While holding part in position, drill 8mm (5/6 ) hole in location. (Fig. 6-) 8mm it Fig. 6- Install supplied push pin into location while holding part into bumper panel. (Fig. 6-) (e) Repeat procedure for other side. Fig. 6- Page 4 of 5 pages Issue: 08/0/ IO
hecklist - these points MUST be checked to ensure a quality installation. heck: Look For: ccessory Function hecks Gaps between mudguards and body side Excessive gaps greater than.0 mm. Page 5 of 5 pages Issue: 08/0/ IO