88 5100 002 Buffet with s and s IMPORAN NO Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Buffet Unit Part List G. Back Stretcher. Back Stretcher A. Side Panel B. Side Panel C. Middle Panel D. Middle Panel. Back Panel F. Back Piece I. J. K. L. Fixed Shelf M. Base N. Leg O. P. Q. Shelf R. S.. (Knock-Down Construction, please refer to the last page of these instructions for steps to complete assembling drawers) ardware List ex Wrench (long) 8 pcs. (+1 extra) 14 pcs.(+1 extra) Wood Screw (short) for Base Part 1 (+1 extra) Wood Screw for Back Panel 1 (1 extra) Machine Screw 8 pcs. Pull andle Small ex Wrench 4 pcs. (+1 extra) 8 pcs.(+1 extra) Screw 14 pcs.(+1 extra) Wood Screw (long) for Side Part 24 pcs. (+1 extra) Adjustable Pin 8 pcs. (+2 extra) Pull andle ools required for assembly : Phillips screwdriver ools recommended for assembly :Level ome Styles Consumer Assistance Line 888-680-7460 and 877-831-0319 servicedesk@homestyles-furniture.com Revised : 14Mar2011
Assembly Instructions 2/5 IMPORAN * Do not tighten up all the screws until each part is properly assembled. *You should keep ex Wrench in a safe place as you may need to tighten up the s in the future. * After assembly, item must be level to work properly. Use the included adjustable levelers to level. SP 1 Put Screws into the pre-drilled holes of Side Panel (A) and (B), and tighten up. A Screw BA A F F G SP 2 Attach Back Stretcher () to Side Panel (A) with. Attach Back Piece (F) to Back Stretcher () and slide Back Panel () into place. Attach Back Stretcher (G) to the unit with s.
Assembly Instructions 3/5 Screw J K I K C L D (long) B SP 3 Attach Middle Panel (C) to the unit with s and s (long). Attach Fixed Shelf (L) and Middle Panel (D) to the unit, using Screws, s, s and s. Assemble (I), (J) and (K), then attach it to the unit with. Attach Side Panel (B) to the unit with s. N SP 4 M Attach Base (M) to the unit with s and s (long). (long) N Attach Leg (N) to Base (M) with s.
Assembly Instructions 4/5 Screw SP 5 Now, you ll be able to create your own Buffet and utch. Make your own choice of the op, wood or stainless steel. SP 6 urn the unit back to its normal position. Place op onto the unit, using s. Put the Screw into the pre-drilled holes at op. Assemble (O) and (P). (see Figure 1) Slide and () into place. Insert Adjustable Pins into both side panels and middle panels at the desired level. R Slide Shelf (Q) into place. Assemble Pull andles to (R) and (S) with Machine Screws. (see Figure 2) Q Adjustable Pin Q S Attach (R) and (S) to the side panels, slide the door lift hinges into the side panel lift hinges.(see Figure 3) o level the unit, adjust the adjustable levelers on the bottom of unit. (see Figure 4) P P O Wood Screw O (Figure 1) SP 7 (Figure 2) (Figure 3) (Figure 4) Insert Wood Screws from the back and tighten up.
Assembly Instructions 5/5 3 1 3 2 (Figure 1) 5 MAK SUR ROLLR IS ON BACK Slide the Plywood Base Part (5) into the grooves on Side Parts (3) and (4). Be sure to push the plywood all the way forward so it meets the Front Part (1). (see Figure 2) 1 4 Using a philips screwdriver, insert 1 screws into the pre-drilled holes as shown, tighten half way. (see Figure 1) 3 (Figure 2) 5 2 1 4 2 (Figure 3) Part List 4 Insert the remaining 1/2 screws into the pre-drilled holes on Base Part (5), then tighten all screws. (see Figure 3) (Figure 4) * If you are missing any of these parts, please contact our DMI Customer Service Department at 1-877-831-0319 or fax us at 1-800-755-2878. 1. Front Part 2. Back Part 3. Side Part 4. Side Part 5. Base Part