19015 Adjustabe Circe Cutters Cutting Toos Circe cutter with 1 obique bit HSS-E and additiona bit hoders for straight bits (no draw cuts), cutting speed for HSS-E bits approx. 8-25 m/min. (stee and iron sheeting), for carbide bits approx. 30-90 m/min. For use in fixed driing machines. For cutting out borehoes, discs and rings, in sheeting made of stee, iron, brass and auminium with a max. thickness of 5, from one side. For machining seaing materia, rubber, eather, Pexigas, with a max. thickness of 30, as we as composites. Note: Do not use in high-speed machines! Not for use with wood! 19015 101 Liiput, cutting range 18-80, shank Ø 10. 19015 103 00, cutting range 30-200, shank Ø 12. 19015 104 00, cutting range 30-200, shank MT 2. 19015 105 00, cutting range 30-200, shank MT 3. 19015 106 00a, cutting range 30-400, shank MT 3. 19015 103 19015 104 Cutting Shank Ø 19015 range Ø MT Liiput 18-80 10 101 00 30-200 12 103 00 30-200 2 104 00 30-200 3 105 00a 30-400 3 106 19026-19028 Spare Bits and Bit Hoders for Circe Cutters Suitabe for type Liiput 00 + 00 a 00 a 19026 19027 19028 Bit, with draw cuts, for sheet meta up to 5, 101 101 stee, non-ferrous or ight meta, made of HSS-E. Bit, obique, for meta up to 5, 102 102 with carbide tip. 19026 101-102 19027 101-102 Additiona bit hoder, for obique bits end-no. 101 and 102. 104 Bits, for seaing materia, pastic sheets, 105 105 rubber, eather with a max. thickness of approx. 10, made of HSS-E. 19026 105 19027 105 Bit, for pastics up to approx. 30, and 106 106 Novotex, Pertinax, Pexigas etc., made of HSS-E. Bit, for pastics up to approx. 30, and 107 107 Novotex, Pertinax, Pexigas etc., carbide-tipped. 19026 106-107 19027 106-107 Additiona bit hoder, for straight bits end-no. 105, 106 and 107. 109 Spare bits, reinforced mode for sheet meta with a max. thickness of 12 111 and borehoes from approx. 34 approx. 150 Ø, made of HSS-E. 19028 111 Specia bit hoder, for reinforced HSS-E bits end-no. 111. 112 19350 Cooant Taps With permanent magnet 260 N, fexibe tube 300 ong, with finey adjustabe stopcock. Hose couping R1/4 inch and/or pipe socket LW 8, arge diameters 69, height 110. The cooant tap can be attached anywhere on the machine too or directy on the workpiece. Cooant or compressed air can be directy appied to wherever it is required. 19350 19350 101 www.hhw.de 19.1
Cooant tubes Lubricants Track ois Cutting paste Cutting oi 19357-19359 E For shortening and extending as required. Vibration-resistant, remains in position. Corrosionproof and resistant to chemicas and sovents. Easiy exchangeabe nozzes, junctions, and screw connectors. Fexibe Pastic Cooant Tubes 19357 101 1/4 inch set, 29-part, in pastic box. 19357 102 1/2 inch set, 33-part, in pastic box. 19358 101 1/4 inch set, 6-part. 19358 104-145 1/4 inch singe eements 19359 101 1/2 inch set, 6-part. 19359 104-145 1/2 inch singe eements 1/4 inch 19358 Set and singe parts Pack consists of: 280 tube 1 ea. round nozze Ø 1,5 / 3 and 6 1 ea. connection thread NPT 1/8 inch and 1/4 inch 101 2 tubes of approx. 140 104 7,5 m tube (55 pieces of 140 ) 106 1 pack with 4 connection threads NPT 1/8 inch 110 1 pack with 4 connection threads NPT 1/4 inch 111 1 pack of 4 round nozze Ø 1,5 112 1 pack of 4 round nozze Ø 3,0 113 1 pack of 4 round nozze Ø 6,0 114 1 pack of 2 fat nozzes 25 x 0,8 115 1 pack with 2 joint nozzes Ø 1 x 16 120 1 pack consists of: 1 ea. fat nozze 12 x 1,0 and 12 x 1,5 1 ea. nozze 5 x Ø 1,5 and 7 x Ø 1,0 124 1 pack with 2 Y-junctions 128 1 pack of 4 extension je 95 with camping ring 131 1 ring system with 15 radia nozzes 132 1 pack of 2 return vaves 135 1 pack with 2 ocking taps with externa thread 1/4 inch 136 1 pack of 2 ocking tap with segment connector 138 1 assemby piers for fixing and oosening the joints 145 1/2 inch 19359 Set and singe parts Pack consists of: 280 tube 1 ea. round nozze Ø 6 / 9 and 12 1 ea. connection thread NPT 3/8 inch and 1/2 inch 101 2 tubes of approx. 140 104 7,5 m tube (59 pieces of 140 ) 106 1 pack with 4 connection threads NPT 3/8 inch 110 1 pack with 4 connection threads NPT 1/2 inch 111 1 pack of 4 round nozze Ø 6 112 1 pack of 4 round nozze Ø 9 113 1 pack of 4 round nozze Ø 12 114 1 pack of 2 fat nozzes 32 x 4,2 115 1 pack of 2 fat nozzes 63 x 2,8 116 1 pack consists of: 1 ea. fat nozze 18 x 2,0 and 18 x 3,2 1 ea. nozze 7 x Ø 2,0 and 5 x Ø 3,2 124 1 pack consists of: 1 ea. 90 nozze Ø 6 / 9 and 12 1 90 nozze 125 1 pack with 2 Y-junctions 127 1 pack with 2 adapters to 1/4 inch 129 1 pack with 2 Y-junctions with adapter to 1/4 inch. 130 1 pack of 4 extension 95 with camping ring 131 1 ring system with 15 radia nozzes 132 1 pack of 2 return vaves 135 1 pack with 2 ocking taps with externa thread 1/2 inch 136 1 pack of 2 ocking tap with segment connector 138 1 assemby piers for fixing and oosening the joints 145 19357 Set 1/4 inch set 101 1/2 inch set 102 19357 101 19357 102 Contents of 1/4 inch set 8 tube pieces of 90 3 thread nippes NPT 1/8 inch 3 thread nippes NPT 1/4 inch 3 round nozzes Ø 1,5 3 round nozzes Ø 3,0 3 round nozzes Ø 6,0 1 nozze 5 x Ø 1,5 1 nozze 7 x Ø 1,0 1 fat nozze 25 x 0,8 1 ocking tap with segment connector 1 Y-junction 1 assemby piers Contents of 1/2 inch set 6 tube pieces of 140 4 thread nippes NPT 3/8 inch 4 thread nippes NPT 1/2 inch 2 round nozzes Ø 6 2 round nozzes Ø 9 2 round nozzes Ø 12 1 90 nozze Ø 9 1 90 nozze Ø 12 2 fat nozzes 32 x 4,2 2 fat nozzes 63 x 2,8 1 ocking tap with segment connector 2 extension pieces à 95 2 camping rings 1 Y-junction 1 assemby piers 19.2 www.hhw.de
19300 Cooing Lubricant Cooing and machining ubricant with high corrosion protection and EP additives, satisfies the highest requirements. Semi-transparent emusion (minera oi: 40 %). Longer service ife compared to standard cooing and machining ubricants. Adapted to HHW track ois 68 and 220 (demusifying). Very to gente the skin, ph at 5 % approx. 9,3. Not a hazardous substance, does not contain chorine, nitride or formadehyde. Very good corrosion protection even at ower concentrations (starting at 3 %). The grease fim is consistent at the cutting toos even at high oads in moecuar strength. Refractometer vaue 1,3. Water contaminant cass 2. Long-asting foam, very we suited for high-pressure CNC machines. Suitabe for a materias. Aso very suitabe for high-strength stee and internay cooed toos. Especiay suitabe for machining non-ferrous Cutting Toos metas. 1:25 (4 %) for ight-duty machining up to 1:10 (10 %) for very heavy-duty machining. 19300 Contents 19300 10 101 25 102 19302 Track Ois Adapted to HHW cooing ubricants, demusifying, therefore it cannot be mixed with the emusion. No sticky residues on the guideways, consideraby extends the service ife of the emusion. Specia additives prevent the jerky giding of machine too tabes and guides and guarantee constant giding even when working with very ow feed rates. Therefore, an exact positioning of the toos and/or the workpiece are made possibe. Demusifying specia oi for tracks and guides. Aso suitabe as hydrauic oi in compiance with DIN 51524/2 and transmission oi. 19302 Contents Kinematic Density Fash point 19302 viscosity at 15 C C 10 68 0,876 230 101 10 220 0,891 240 102 19304 For heavy-duty machining and for chip remova. Thread cutting, centering, machining keyways and reaming with reamers. range: High-aoyed carbon stee, chrome-nicke aoys, VA, austenitic, ferritic chrome-nicke stee, titanium, manganese, cast stee, grey cast iron, maeabe cast iron etc. Stainess Stee Lubricating Sticks/Cutting Pastes 19304 101 Lubricating sticks Especiay suitabe for ubricating meta saw bades. Sticks to the bade, very good ubricating effect. 19304 102-103 Cutting paste In container. 19304 101 19304 102-103 Contents 19304 g Lubricating sticks 300 101 Cutting paste 120 102 Cutting paste 750 103 19306 Without chorine and minera oi. High-quaity mutipurpose cutting oi, based on natura raw materias. Low too wear, efficient. For medium through heavy-duty machining. Proven and tested with high-aoyed and stainess stee. Especiay suitabe for driing, tapping, thread cutting, miing, reaming, turning, machining keyways, sawing, grinding and punching. A kinds of stee, aoyed and unaoyed. A cast metas, e.g. cast stee, grey cast iron, maeabe cast iron etc. Muti-Purpose Cutting Ois auminium and copper and a chrome-nicke compounds. Titanium, manganese. Universa use for machining and forming. For appication in cooing systems and minima-amount ubricating systems. 19306 101 19306 102 19306 103-104 Content Content 19306 m Spray can 300 101 Sprayer 500 102 Container 5 103 Container 10 104 www.hhw.de 19.3
Concentrated grinding ubricants Concentrated cooing ubricants Emusion mixers Refractometers Band skiers Cutting oi Thread taow 19308 Synthetic grinding concentrate with high corrosion protection and EP additives, satisfies the highest requirements. The emusion is transparent and therefure fufis the demands of cear-vision grinding. Longer service ife compared to standard cooing and machining ubricants. Very to gente the skin, ph at 2,5 % approx. 8,5. Not a hazardous substance, does not contain chorine, nitride or formadehyde. Very good corrosion protection even Grinding Concentrates at ower concentrations (starting at 2 %). Grinding partices quicky sette to the bottom of the container, therefore they do not hamper grinding performance. Refractometer vaue 2,1. Water contaminant cass 2. For grinding of different materias (meta, pastics, ceramics). 1:40 (2,5 %). Aso suitabe as additive to pressure water, as additiona corrosion protection and as stabiiser. 19308 Contents 19308 10 101 25 102 19360 Water-emusive muti-purpose cooant and cutting iquid. Free of nitrite, siicone and pheno. For a wide range of appications, for cutting, machining and working iron, cast meta, non-ferrous metas, stee with ow through medium carbon content, stee with high strength, stainess and heat resistant stee, as we as titanium and titanium aoys. For driing, tapping, thread cutting, miing, reaming, turning, machining keyways, sawing, grinding and punching. Concentrated Cooing Lubricants 19360 Contents 19360 Container 10 101 Barre 210 102 19365 Emusion Mixers 19365 101 Emusion mixers Water connection R 1/2 inch, suction height max. 2m, approx. 1500/h ready mixture at fow pressure of approx. 2,5bar, housing made of specia stee, stainess, with adjustment tabe. Ready for connection to water pipe. For quick preperation of water-mixed (water-emusive) cooing ubricants. The mixer is connected to a water pipe and a container of concentrated cooing ubricant; the mixture is ready as soon as the water suppy is turned on. The percentage of concentration can be reguated over a wide range using a very fine reguating side. 19365 102 Safety oop R 1/2 Compete with back fow stop, pipe ventiation and through fow reguator. The safety oop must be instaed when the emusion mixer is connected to a drinking water pipe. Note: According to the safety reguations of DVGM DIN 1988 section 8.1.13, emusion mixers need to be equipped with a safety oop when connected to a drinking water pipe. 19365 19365 Mixer 101 Loop 102 19370 Refractometers Measuring range 0-32%. With adjustabe eyepiece, accuracy of reading 0,2%, in protective pouch. For fast and accurate measurement of the concentration of water-mixed cooing ubricants and many other soutions in various areas of appication. 19370 19370 101 19.4 www.hhw.de
19372-19374 Band Skiers and Spare Bands Cutting Toos 19372 Compact construction, vertica fixing position or up to 30 anged. Endess skier band, 45 width, magnetic stand, fow capacity approx. 2-6 /h on surface. For care of cooant ubrications on machine toos, machining centres, CNC athes a.s.o. Cared-for cooing ubricants have a consideraby onger service ife, ensure better working hygiene, proong the cooing ubricant exchange intervas and reduce costs. Thanks to its great performance, the band skier can fiter waste ois and other swiing dirt out of the ubricants even when other systems are ess successfu. 19372 Technica specifications: Eectric connection: Power cabe: Drive: Mounting depth (ET): Optionay avaiabe: Band capacity: Outfow: Weight: 230 V, 50 Hz, AC 1,3 m with 12 V mains adaptor, adjustabe Gear motor 12 V, 4 W, 100% ED Seectabe 160, 260, 530 Modification of ET possibe by exchange of teescope bar and band Approx. 2-6 /h surface oi Joint hose 1/2 inch Approx. 2 kg 19374 Band skier Spare skier bands Mounting depth (ET) 19372 19374 160 101 101 260 102 102 530 103 103 19375 Cutting Oi Spray Cutting oi for demanding requirements. Extends too ife, aows smaer toerance ranges, absoutey not harmfu. Non-reactive to meta and non-corrosive. Not harmfu to the skin, non-toxic. Pump spray without propeant. For threading, reaming and driing. 19375 Contents 19375 m 400 101 Handy stick. 19378 Thread Taow Greases threads in order to achieve a better siding resut. Prevents the threads from breaking. 19378 Contents 19378 approx. g 600 101 19379 Thread Cutting Ois and Greases With exceent active substances. Highy concentrated. Free of chorine, PCB and sovents. Universa use, for high output, high cutting power, optima surface quaity, exact dimensions, ong too ife and cean threads. 19379 102 Akawax Thread cutting ois Soid. For thread cutting and for meta saws. 19379 101 19379 102 19379 101 Akafi Thread cutting oi Viscuous, in handy dosing botte. For thread cutting. Content Content 19379 m g Akafi 220 101 Akawax 350 102 www.hhw.de 19.5
Chip safety shieds Magnetic chip retrievers Chip shears Chip hooks 19380-19381 Chip Safety Shieds 19380 With magnetic base 55 x 40 x 45 and paraboic acryic pastic shied, 360 swive range. Adhesive force approx. 40 kg. Shaft with ba joint is adjustabe and swives in a directions. By oosening or tightening the safety nut on the shaft, any pressure up to 100% (steady hod) can be generated. Note: The V-notch in the base aows for easy mounting on fat and cyindrica surfaces. Effective guard against fying chips, sparks and cooant on athes, grinding, miing and driing machines. Unobstructed view of workpiece and too! 19381 Spare safety shied 19380 Shied size 19380 19381 200 x 250 101 101 250 x 300 102 102 300 x 400 103 103 19390 Magnetic Chip Retrieving Too 1 too - 2 purposes: 1. Removing chips, 2. retrieving sma parts. Stainess stee. Just move the magnet inside the round rod up and down. The strong magnet attracts the meta chips. Push the button and the chips fa off. 19390 Length 19390 400 101 19395 Chip Shears With hand guard and 2 bades. Cuts sharp ribbon chips as soon as they are formed or when the machine is stopped. Protects the athe operator from injury. 19395 Length 19395 320 101 19396 Chip Hooks With hand guard. For removing sharp meta chips wherever it is not necessary to cut. 19396 Tota ength Hook ength 19396 535 355 101 19397 Chip Hooks With round protection shied 135 Ø. Strong hook (width: 8 at protection shied) tapered to 3 at hook end. For the remova of ong chips. 19397 19.6 Overa ength Hook ength 19397 approx. 420 300 201 620 500 202 www.hhw.de