General Specifications Prime Center Panel 4.7 5. 5.7 Door Construction: 5 Piece MDF with 44 applied moulding around the outside of the rails. Center Panel Construction: 3/8 recessed panel. See drawings for other available options. Cabinet Line Availability: Available with Full Access Frameless & Inset Frame only. Rail/Stile Size Options: Default Rail is 3 1/W. Minimum Rail is 2 1/W with Concealed Hinges. Maximum Rail is 4 1/W, but this becomes a function of cabinet width. Frameless Drawer fronts: Minimum Stile width is W for proper drawer box attachment. Inset Frame Drawer fronts: Minimum Stile width is 1 1/W for proper drawer box attachment. Minimum HINGED Door Size: Based on Prime Rail/Stile Width and Prime Panel: 8 W x 8 H. We often get the question: Your drawer fronts are 5 7/8 H, why isn t the minimum door width 5 7/8 W?. If we were to use a drawer front turned to become a door, the rails and stiles would be reversed and beside a standard door, this would look odd. Hinged doors smaller than the listed minimum width will be manufactured with slab doors. Minimum PULL OUT Door Size: Based on 2 1/W Stiles and Prime Panel: 6 1/W x 6 1/H. As the width of the door decreases, the stiles will remain full size until the center panel reaches 1 1/W, at that point the stile width will decrease until it reaches the minimum of 2 1/. Maximum Door Size: 2W x 7H (Absolute maximum height) Wider doors will have intermediate cross rail and multiple panels. s can be removed, however this voids the warranty. Radius Doors Available: 3 Dimensional Mitered Doors Available: Wainscot/Appliance Panel Types: Not available, create a new room, and select the standard Imola door style. Wainscot Arch & Arched Top Door Availability: Recessed Filler/Pilaster Availability: Yes. 3/8 Recessed Additional Panel Options 1/ Recessed Edge Type Availability INTEGRAL SQUARE EDGE Frame Availability Appliance Frames: 3/Thick material with a square outside edge will be used. #44 applied moulding is NOT available. Decorative Frames: 3/Thick material with a square outside edge will be used. #44 applied moulding is NOT available. Reverse Raised
Drawer Front Options Standard Door Match Drawer Front Specifications 3/TH Slab with 44 Moulding (Most Common) Drawer Front Ordering Methodology: As the drawer front height increases beyond the default top drawer height (which is different for each cabinet line), the drawer rails will increase in size until the full rail width is attained. The center panel will remain the same until the rails have reached full width. At this point the center panel will begin to increase along with the drawer height. The information below is based on the prime door rail width of 3 1/. The dimensions shown WILL change if a rail size other than 3 1/ is selected. The following information is also representative of the prime configuration of rails, stiles and center panel as shown on the left side of this page. 4.7 5. 5.7 DH Recessed Door Match w/44 Mldg Vertical stiles will be full size. See chart for top & bottom rail sizes as well as space for hardware, according to drawer front height. DH Full Access Frameless Top Drawer Less than 5.87H Slab Only DH - (2 x outside edge profile) Top Drawer (Recessed) 5.87H W 0.87H Lower Drawer (Recessed) H - 7.2H ( DH - 0.875 ) / 2 0.87H Lower Drawer (Recessed) 7.37H + W DH - 6.5 Recessed Door Match 1. w/44 Mldg Designed for Inset Frame Cabinets ONLY. Inset Frame Top Drawer Less than 5.437H Slab Only DH - (2 x outside edge profile) Top Drawer (Recessed) 5.437H W 0.437H Lower Drawer (Recessed) 5.562H - 7 H ( DH - 0.4375 ) / 2 0.437H Lower Drawer (Recessed) 7.12H + W DH - 6.5 Full Overlay Frame Top Drawer Less than 6.H Slab Only DH - (2 x outside edge profile) Top Drawer (Recessed) 6.H W 1.H Lower Drawer (Recessed) 6.62H - 7.87H ( DH - 1.5 ) / 2 1.H Lower Drawer (Recessed) 8 H + W DH - 6.5 DH = Drawer Height The minimum flat space (for hardware) that we allow on a drawer front is 5/8. The default top drawer height is a cabinet line dependent value that we base all other drawer fronts on.
Availability Profile: 3 8 " Most mullion styles have suggested ratios for width and height in order to maintain proper proportions for the design. Please refer to the mullion door specifications for these suggested sizes. 13 16 " 10Lite 9EQLite 9Lite 8Lite (Wide Rail) 8Lite 6Lite 2P4Lite 2P1Lite 2Lite 1Lite 4Lite 5.7 5. 4.7 2P9Lite Porthole 2P Porthole Porthole 9Lite Porthole Harmony Glass 3Lite C Quarter Arch 4LiteAC-4 2P3LiteAC-4 12Lite (Wide Rail) 12Lite 7Lite Helix Unitas 2P4Lite 2P2Lite 2Lite 13 Lite Symphony 10 Lite Symphony 7 Lite Symphony 2P Symphony Symphony
Availability Profile: 3 8 " Most mullion styles have suggested ratios for width and height in order to maintain proper proportions for the design. Please refer to the mullion door specifications for these suggested sizes. 13 16 " 4.7 5. 5.7 10Lite Gothic Arch 11Lite Ellipse 12Lite Gothic DBLARCH 6Lite Hourglass 12Lite Hourglass 16Lite Hourglass 4Lite X 4Lite X 2 Panel 4 Lite X 2 Panel 4 Lite X 16Lite X 16Lite X 12Lite X 12Lite X 8Lite X 8Lite X
Finish Door Style Factors for Available Species 4.7 5. 5.7 5 Piece MDF doors will telegraph the joint location between the stile and rail. There will be open gaps at the joint between the panel and the rail. As a result, surface hairline fractures may develop at the joints. THIS IS NOT A WARRANTY ISSUE. It is required that a sample door is viewed before the cabinetry order is placed. Back of Door & Drawer Standard Finish: The standard finish for the back of all doors and drawer fronts is base paint without glaze. An additional charge will be applied to finish the backs of the doors and drawers exactly like the fronts. All door style factors listed below are based on the Prime Rail/Stile Width and Center Panel Configuration for this door style as shown on the left side of this page. Any changes to the prime door style, included rail/stile width changes, panel changes, etc. will result in changes to the door style factor (DSF) and price point (P.P.). Species DSF 20/20 Alder (Clear, Knotty) N/A N/A Aqua Gloss N/A N/A Ash - Quarter Cut White N/A N/A Bamboo (Caramel, Natural Light) N/A N/A Cherry (Flat Cut, Knotty, Quarter Cut) N/A N/A Cypress - Select Grade N/A N/A European Steamed Beech (Flat Cut, Quarter Cut) N/A N/A Hickory - Flat Cut N/A N/A High Pressure Laminate N/A N/A Mahogany (Khaya) N/A N/A Maple (Flat Cut, Quarter Cut) N/A N/A MDF - 1 Piece N/A N/A MDF - 5 Piece 1.98 15 Melamine N/A N/A Oak (Flat Cut, Quarter Cut, Rift Cut, Textured) N/A N/A Paint Grade N/A N/A PET (High Gloss, Ultra Matte) N/A N/A Pine (Clear, Knotty) N/A N/A Quarter Cut Black Limba N/A N/A Red Birch N/A N/A Sapele - Ribbon Cut N/A N/A Stainless Steel N/A N/A Teak (Flat Cut, Quarter Cut) N/A N/A Tineo N/A N/A Veneer - Textured Faux Wood N/A N/A Vision Series Veneers N/A N/A Vista Series Veneers N/A N/A Walnut (Flat Cut, Quarter Cut) N/A N/A