echnical data sheet Parameterisable damper actuator in the IP66 protective housing for or adjusting ad usting air dampers in industrial plants and in technical building installations For air dampers up to approx. 3. m orque 6 Nm Nominal voltage AC/DC V Control: modulating DC 0... 0 V or variable Position feedback DC... 0 V or variable Running time 7 s or variable Optimum weather protection for outdoor applications echnical data Electrical data Nominal voltage AC V, 50/60 Hz / DC V Nominal voltage range AC 9.... 8.8 V / DC.6... 8.8 V Power consumption In operation 5 W @ nominal torque At rest W For wire sizing 6 VA (l max 0 A @ 5 ms) Connection Cable m, x 0.75 mm Functional data Factory settings Variable Settings orque (nominal torque) Min. 6 Nm @ nominal voltage 5%, 50%, 75% reduced... Control Control signal DC 0... 0 V, input impedance 00 k Open-close, modulating (DC 0... 3 V)... Operating range DC... 0 V Starting point DC 0.5... 30 V End point DC.5... 3 V... Position feedback (Measuring voltage) DC... 0 V, max. 0.5 ma Starting point DC 0.5... 8 V End point DC.5... 0 V... Position accuracy ±5% Direction of rotation Reversible with switch 0 / Direction of motion at = 0 V At switch position 0 or, respectively Electronically reversible... Manual override Gearing latch disengaged with push button, can be locked Angle of rotation Max. 95, can be limited at both ends with adjustable mechanical end stops Angle of rotation limiting min. 30 Running time 7 s / 90 7... 35 s... Automatic adjustment of operating range and measuring signal to match the mechanical angle of rotation Override control Manual triggering of the adaption by pressing the «Adaption» button or with the PC-ool Automatic adaptation resp. synchronisation whenever the supply voltage is switched on... MAX (maximum position) = 00% MAX = (MIN 30 )... 00% MIN (minimum position) = 0% MIN = 0%... (MAX 30 ) ZS (intermediate position, only AC) = 50% ZS = MIN... MAX... Sound power level 5 db (A) With a 7 s = 5 db (A) running time of 35 s = db (A) Position indication Mechanical, pluggable Negative torque! 50% from nominal torque (Caution: can only be used with restrictions. Please contact your Belimo representative.) Safety Protection class III Safety extra-low voltage L Class Supply Degree of protection IP66 NEMA, L Enclosure ype EMC CE according to 00/08/EC Certification Certified to IEC/EN 60730- and IEC/EN 60730-- clus according to L 60730-A and L 60730-- and CAN/CSA E60730-:0 Mode of operation ype www.belimo.com - en v.0 0.0 Subject to changes / 7
echnical data (Continued) Safety Rated impulse voltage 0.8 kv Control pollution degree Ambient temperature 30... 0 C (no restrictions) Non-operating temperature Ambient humidity Maintenance! 0... 50 C (Caution: can only be used with restrictions. Please contact your Belimo representative.) 0... 80 C 00% r.h. Maintenance-free Dimensions / Weight Dimensions See «Dimensions» on page 7 Weight Approx..7 g Safety notes! he actuator is not allowed to be used outside the specified field of application, especially in aircraft or in any other airborne means of transport. It may only be installed by suitably trained personnel. Any leg al reg ulations or reg ulations issued by authorities must be observed during installation. he cover of the protective housing may be opened for adjustment and servicing. When it is closed afterwards, the housing must seal tig ht (see installation instructions). he device on the inside may only be opened up in the factory. It does not contain any parts that can be replaced or repaired by the user. he cable must not be removed from the device on the inside. on the inside. Adaptation is necessary when the system is commissioned and after each adjustment of the ang le (press the adaptation push-button) When calculating the required torque, the specifications supplied by the damper manufacturers (cross-section, desig n, installation site), and the air flow conditions must be observed. he device contains electrical and electronic components and is not allowed to be disposed of as household refuse. All locally valid reg ulations and requirements must be observed. he actuator is not desig ned for applications where chemical influences (g ases, fluids) are present or for utilisation in corrosive environments in g eneral. he materials used may be subjected to external influences (temperature, pressure, constructional fixture), that cannot be simulated in laboratory test or field trials. In case of doubt, we definitely recommend that you carry out a test. his information does not imply any leg al entitlement. Belimo will not be held liable and will provide no warranty. For L (NEMA) ype applications flexible metallic cable conduits or threaded cable conduits of equal value are to be used. he actuator may not be used in plenum applications (e.g. suspended ceiling s or raised floors). / 7 - en v.0 0.0 Subject to changes www.belimo.com
Product features Fields of application Mode of operation Parameterisable actuators Simple direct mounting Manual override Adjustable angle of rotation High functional reliability Home position he actuator is particularly suitable for utilisation in outdoor applications and is protected against the following weather conditions: V radiation rain / snow dirt / dust humidity Changing atmosphere / frequent and severe temperature fluctuations (recommendation: use the actuator with integrated factory-installed heating which can be ordered separately to prevent internal condensation *) he actuator is controlled with a standard modulating signal of DC 0... 0 V and moves to the position defined by the control signal. he measuring voltage serves for the electrical display of the damper position 0... 00% and as slave control signal for other actuators. he factory settings cover the most common applications. Input and output signals and other parameters can be altered with the BELIMO Service tool MF-P or the adjustment and diagnostic tool ZH-GEN Simple direct mounting on the damper spindle with a universal spindle clamp, supplied with an anti-rotation strap to prevent the actuator from rotating. Manual override with push-button possible (the gear is disengaged for as long as the button is pressed or remains locked). Adjustable angle of rotation with mechanical end stops. A minimum permissible angle of rotation of 30 must be allowed for. he housing cover must be removed to set the angle of rotation. he actuator is overload-proof, requires no limit switches and automatically stops when the end stop is reached. he first time the supply voltage is switched on, i.e. during initial startup, the actuator carries out an adaptation. After pressing the «gear disengagement» pushbutton, the actuator moves to the home position at the end stop. Pos. Direction of rotation Home position 0 = 0 ccw Left stop = 0 cw Right stop he actuator then moves into the position defined by the control signal. Adaption and synchronisation During adaptation, the upper and lower spindle end stop is recorded and deposited in the actuator. Detection of the mechanical end stops enables a gentle approach to the end positions and thus protects the actuator mechanism. During synchronisation, the actuator moves to the home position for angle referencing. his ensures correct position regulation. * in development Accessories Description Data sheet Electrical accessories Auxiliary switch S..A.. - S..A.. Feedback potentiometer P..A.. - P..A.. PC-ool MF-P from version 3.3 Adjustment and diagnostic tool ZH-GEN Range controller SBG Positioner SGA, SGE and SGF Digital position indication ZAD Heating with mechanical hygrostat * Heating with adjustable thermostat * * in development M9 - ZH-GEN - SBG - SG.. - ZAD www.belimo.com - en v.0 0.0 Subject to changes 3 / 7
Electrical installation Wiring diag ram Note Connect via safety isolation transformer.! Parallel connection of other actuators possible. Note performance data for supply. 3 5 DC 0... 0 V DC... 0 V Cable colours: = black = red 3 = white 5 = orange Cable leng ths C A = Actuator C = Control unit L = Belimo connecting cable, m ( x 0.75 mm ) L = Customer cable L tot = Maximum cable length L Note When several actuators are connected in parallel, the maximum cable length must be divided by the number of actuators. 3 5 L L tot A Cross section L / Max. cable length L tot = L L AC DC Example for DC 0.75 mm 30 m 5 m m (L ) m (L ).00 mm 0 m 8 m m (L ) 7 m (L ).50 mm 70 m m m (L ) m (L ).50 mm 00 m 0 m m (L ) 9 m (L ) N L AC 30 V AC V C A = Actuator C = Control unit L = Belimo connecting cable, m ( x 0.75 mm ) L Note here are no special restrictions on installation if the supply and data cable are routed separately. 3 5 A / 7 - en v.0 0.0 Subject to changes www.belimo.com
Functions with basic values Override control with AC V with relay contacts a b c e.g. N 007 (DC 0... 0 V) From controller Functions a b c 0% Override control with AC V with rotary control switch 3 (DC 0... 0 V) From controller e.g. N 007 Pos 0% Functions 3 5 ZS 50% (intermediate position) 3 5 ZS 50% (intermediate position) 00% 3 00% Control mode in accordance with Control mode in accordance with Remote control 0... 00% Minimum limit 3 Z SGA SGF SGE Positioner 3 Z SGA SGF SGE Positioner [V] 0 (DC 0... 0 V) From controller 3 5 3 5 min 0 [%] 0 00 Master/Slave control (position-dependent) Control with... 0 ma via external resistance DC...0 V 500 Ω () ()... 0 ma DC...0 V o the following actuator DC... 0 V 3 5 3 5 3 5 Master actuator Slave actuator he 500 resistor converts the... 0 ma current signal into a voltage signal DC... 0 V Position indication Functional check 3 ZAD Adapting the direction of rotation 3 5 3 5 Procedure Apply V to connection and Disconnect connection 3: For direction of rotation 0: Actuator turns in the direction of For direction of rotation : Actuator turns in the direction of Short circuit connections and 3: Actuator runs in the opposite direction www.belimo.com - en v.0 0.0 Subject to changes 5 / 7
Functions for actuators with specific parameters Override control and limiting with AC V with relay contacts 3 a b c d 5 e e.g. N 007 (DC 0... 0 V) From controller Functions a b c d e CLOSE ) MIN ZS (intermediate position) MAX Override control and limiting with AC V with rotary control switch 3 CLOSE ) 5 MIN ZS MAX OPEN (DC 0... 0 V) From controller e.g. N 007 OPEN Control mode in accordance with ) Caution! his function is only guaranteed if the start point of the operating range is defined as min. 0.6 V. Open-close control 3 5 Operating controls and indicators Direction of rotation switch Switching over: Direction of rotation changes Push-button and green LED display Off: No voltage supply or fault On: In operation Press button: Switches on angle of rotation adaptation followed by standard operation 3 3 Push-button and yellow LED display Off: Standard operation On: Adaptation or synchronising process active Press button: No function 5 Gear disengagement switch Press button: Gear disengaged, motor stops, manual override possible Release button: Gear engaged, synchronisation starts, followed by standard operation 5 Service plug For connecting parameterising and service tools Check voltag e supply connection a) Off and 3 On Check the supply connections. Possibly and are swapped over. b) Blinking and 3 Blinking 6 / 7 - en v.0 0.0 Subject to changes www.belimo.com
Dimensions [mm] Dimensional drawing s 9 0 63 Damper spindle Leng th 6... 75... 6.7 5.5 86 38 35... mm... 8 mm 7... 6.7 mm... 8 mm 330 www.belimo.com - en v.0 0.0 Subject to changes 7 / 7
GM..GX(-..) / SMQG(-..) 760-0000.A 5 6...75mm... mm... 8 mm 3... 6.7 mm... 8 mm 3 6 3 3 mm 5Nm www.belimo.com M-GM..GX(-..)/SMQG(-..) v.0 05.0 / 3
GM..GX(-..) / SMQG(-..) 7 8 65.5Nm / 3 M-GM..GX(-..)/SMQG(-..) v.0 05.0 www.belimo.com
GM..GX(-..) / SMQG(-..) N L N L 0 3 3 0 0 AC V / DC V 3 GMGX SMQG AC 00... 0 V N L L! 3 GM30GX AC V / DC V DC 0 0 V DC 0 V DC 0 0 V MP 3 5 3 5 GMGX-SR SMQG-SR GMGX-MF GMGX-MP www.belimo.com M-GM..GX(-..)/SMQG(-..) v.0 05.0 3 / 3