BT.. D/E S E R I E S DIN rail mounting temperature controller with current transformer input deltadue series D line The controller with load control The deltadue series includes a powerful DIN rail mounting controller module capable to detect the failures of both the electric load and the solid state relay. The D line can satisfy a wide range of applications requiring temperature control to be integrated with PC and PLC systems. The features of the line include: Common bus for power supply and serial communications Totally withdrawable Easy replacement without switching off the power supply Digital input for remote commands Timer and Start-Up function Automatic tunig Four outputs Current transformer input Full integration with the deltadue series data acquisition and control modules Easy and simplified installation and maintenance E ISO 9 Certified
6 7 8 6 7 8 6 7 8 6 7 8 6 7 8 6 7 8 6 7 8 6 7 8 6 7 8 6 7 8 deltadue distributed control Advantages and peculiarities Keeping costs low Modular construction and compact dimensions - Quick mounting on DIN rail - Possibility of prewiring - Common bus for power supply and serial communications - Polarised connectors - Coloured Terminal identification Wiring error reduction - Mounting on the machine or real panel - Remote/centralised control - RS8/CanBus - Communications interface High integration - Withdrawable - Easy replacement without switching off the power supply Easy maintenance Typical applications Local control with operator panel OP Distributed control with PLC and with dedicated modules for critical loops Distributed control with PC supervision OP COM ALM PLC deltadue PLC OPR PAR ALM OP deltadue 6 7 8 6 7 8 6 7 8 6 7 8 6 7 8 PC PC deltadue Resources Operating mode Control Alarms Main universal input Auxiliary input (option) Digital input PV AUX IL OP OP (option) OP OP Single OP OP OP action OP OP OP OP Double OP OP OP action OP OP OP OP 6 ( option) OP OP OP OP Setpoint (option) IL connected functions Modbus RS8 Parameterisation Supervision Fuzzy tuning with automatic selection One shot Auto tuning One shot Natural Frequency
Technical data Features at env. C Total configurability PV input Description By means of the configuration tool it is possible to select: - type of input - the type of control input - type of output - type and functionality of the alarms - type of Setpoint - control parameter values A/D converter with resolution of. points Common characteristics Accuracy Update measurement time:. sec Sampling time:. sec Input bias: - 6 + 6 digit Input filter: sec. OFF =.% ± digit (for temperature sensor) Between V~.% ± digit (for ma e mv) the error is minimal Resistance PtΩ at C or wires Line: Ω max ( wire) thermometer (IEC 7) connection Input drift: (for Τ: R+R C/ F Burnout. C/ C Env. Temp. must be <Ω) selectable (with any combination) <. C/Ω Wire Res. Thermocouple DC input (current) DC input (voltage) L,J,T,K,S,R,B,N,E Internal cold junction Line Ω max. W,W (IEC 8) compensation with NTC Input drift: C/ F Error C/ C ±, C <µv/ C Env. Temp. selectable ±. C Burnout <µv/ω Wire Res. / ma, Burnout. Engineering.Ω ext. shunt units, decimal point Input drift: Rj >MΩ position configurable <.% / C Env. Temp. low range: -999 9999 <µv/ω R. Wire Res....mV, -mv high range: -999 9999 Rj >MΩ (min range of digits) or ma Current visualization via serial comm.... A Auxiliary CT current input hardware With A resolution inputs transformer selectable and Heater Break Alarm Digital input Operating mode Auto/Man mode change, The closure of the external contact produces Stored Setpoint activation measure hold, any of the following actions: Timer activation (if option installed) single or double action P.I.D. loop or ON/OFF with, or alarms Algorithm P.I.D with overshoot control or On-Off Proportioning band (P). 999.9% Integral time (I).. min Derivative time (D).. min Error dead band.. digits OFF= Overshoot control.. Manual reset..% Cycle time (Time Single action PID proportioning only) sec algorithm Control output high limit..% Control mode Soft-start output value..% OFF= Output safety..% value (-..% for Heat/Cool) Control output hysteresis..% On/Off algorithm Dead band -..% Relative cool gain.. Double action Cycle time (Time PID algorithm proportioning only) sec (Heat/Cool) Control output with Overlap..% high limit Cool output hysteresis..% Fuzzy-Tuning Two methods of tuning are available: - Auto-Tuning one shot - Natural frequency one shot The Fuzzy-Tuning automatically selects one of the two methods which assures the best result for each condition. The Auto-Tuning method works best on the step response basis. When activated, if a deviation exists between the Setpoint and process variable larger than % of scale range, the controller modifies the output value. Then, in a short time, it calculates the PID parameters and the new algorithm is operational immediately. The main advantages of this method are fast calculation and quick implementation. The Natural frequency method works best when the process variable is very near to the Setpoint. When activated, it causes a process oscillation around the Setpoint value. The main advantage of this method is a reduced disturbance to the process. Current transformer With CT option the load current can be measured, read via serial communications and alarm can be generated. The heater break/ssr failure alarm detects both of the following conditions: - low load current during the ON phase of the time proportioning control (heater break) - leakage current higher than % of the full load current during the OFF phase of the time proportioning control (SSR failure) Example: CT installed on OP, alarm on AL with phase ON as active phase (configuration digit p= 8). ms ms OP ON OFF ON t.cur As.p % corrente nel carico AL OFF ON OFF ON OFF
Technical data Features at env. C OP-OP outputs OP output OP output AL- AL - AL alarms Setpoint Special functions (option) Fuzzy-Tuning one shoot Auto/Man Station Serial Comm.s Auxiliary Supply Operational Safety General characteristics Description ST Relay N.O., A/V~ for resistive load SSR SSR, A/V~ for resistive load Too meet the double isolation requirements OP and OP must have the same load voltage ST Relay N.O. A/V~ for resistive load Logic not isolated: /V-, ±% ma max Hysteresys..% Active high Action Deviation threshold ±range Type Band threshold range Active low Absolute threhold whole range Action Sensor break, heater break alarm, Loop break Acknowledge (latching), activation inhibit (blocking) Connected to Timer (if options installed) Local Local plus stored with tracking or Stand-by Timer Up and down ramps. 999.9 digit/min. (OFF=) Low limit: from low range to high limit. High limit: from low limit to high range Automatic start at the power on,manual start by digital inputs or serial comm.s Setting time: 9999 sec/min Stand-by Setpoint: SC.LO <= S.P. >= SL.HI Start-up Setpoint: SC.LO <= S.P.sU >= SL.HI Start-up Hold time: min Control output high limit..% The controller selects automatically the best method according to the process conditions One shot Auto Tuning One shot Natural Frequency Standard with bumpless function, by digital input or serial communications RS8 isolated, Modbus/Jbus protocol,,, 8, 96 bit/sec, two wires +V ± % ma max - for external transmitter supply Measure input Control output Parameters Outputs lock Detection of out of range, short circuit or sensor break with automatic activation of the safety strategies Safety value: -% % Parameter and configuration data are stored in a non volatile memory for an unlimited time Power supply V~ (-% +%) /6Hz and Power (PTC protected) V-(dc voltage) (-%+%) consumption W max Safety EN6- (IEC-), installation class (V) pollution class, instrument class II Electromagnetic compatibility Compliance to the CE standards Protection Terminal strip IP Dimensions Pitch:. mm - deph:. mm with: The digital input can be configured to have one of the following functions: Measure hold Auto/Man mode change Stored Setpoint activation Timer activation To improve the instrument performance and to reduce the wiring and installation costs, two special functions are available: - Start-up Setpoint di Start-up < - Timer Heat/Cool control By a sole PID control algorithm, the controller handles two different outputs, one of these performs the Heat action, the other one the Cool action. It is possible to overlap the outputs. The Cool action can be adjusted using the relative cool gain parameter. The Heat and Cool outputs can be limited separately. Digital input S.P.S.U Setpoint di Start-up > = S.P.S.U The use of these functions avoids additional device installation (e.g. external timer), therefore allowing a significant costs reduction. Output lock function, The outputs can be switched to the OFF status via serial communications. Electrical connections OP CT A NO IC OP OP B 6 7 8 IC NO NO IC C DI OP D B b A RTD TC + VDC OUT RS 8 NC N L V ~
Ordering codes Line Basic model Accessories Configuration st part nd part Model: D B C D _ E F / I L M N _ O P Q R Outputs Serial comm.s Options Instr. handbook Setpoint Alarm AL Alarm AL Alarm AL Output type Control mode Input Outputs OP OP Relay Not fitted Relay Relay SSR Not fitted SSR SSR Serial communications CanBus RS 8 Modbus/Jbus SLAVE Options None Current transformer (CT) Not fitted Start-up + Timer Instruction handbook Italian-English (std) French-English German-English Spanish-English B C D E F Input type Range scale TR Pt IEC7-99.9. C -99.9 7. F TR Pt IEC7-6 C -8 F TC L Fe-Const DIN7 6 C F TC J Fe-Cu% Ni IEC8 6 C F TC T Cu-CuNi - C -8 7 F TC K Cromel -Alumel IEC8 C 9 F TC S Pt%Rh-Pt IEC8 6 C 9 F TC R Pt%Rh-Pt IEC8 6 C 9 F TC B Pt%Rh-Pt 8 C 7 F Pt6%Rh IEC8 TC N Nicrosil-Nisil IEC8 C 9 F TC E Ni%CR-CuNi IEC8 6 C F TC NI-NiMo 8% C F TC W%Re-W%Re C 6 F TC W%Re-W6%Re C 6 F mv linear Engineering units mv linear Engineering units mv Custom scale On request Control mode ON-OFF reverse action ON-OFF direct action P.I.D. single reverse action P.I.D. single direct action Linear cool output P.I.D. double action ON-OFF cool output Water cool output Oil cool output Output type - Singol action Output type - Double action Relay Heat Relay, Cool Relay Digital Heat Relay, Cool Digital Heat Digital, Cool Relay AL-AL-AL type and function Disabled or (AL only) used by Timer Sensor break/loop break alarm Absolute active high active low Deviation active high active low Band active out active in Heater break active during ON output state by CT active during OFF output state Setpoint type Local only Local and tracking stored Setpoints Local and Stand-by stored Setpoints I L 6 7 8 9 6 M 6 7 N O-P-Q 6 7 8 9 R If not differently specified the controller will be supplied with standard version Model: D -
S E R I E S ASCON spa Bollate (Milano) Via Falzarego, 9/ Tel. +9 7 Fax +9 http://www.ascon.it e-mail info@ascon.it Distributed by: