HF/VHF/UHF RF power N-channel MOSFETs Features Datasheet - production data M177 Epoxy sealed Figure 1. Pin connection 4 1 Gold metalization Excellent thermal stability Common source configuration P OUT = 300 W min. with 20 db gain @ 30 MHz Thermally enhanced packaging for lower junction temperatures Description The SD2933 is a gold metalized N-channel MOS field-effect RF power transistor, intended for use in 50 V dc large signal applications up to 150 MHz. Its special low thermal resistance package makes it ideal for ISM applications, where reliability and ruggedness are critical factors. 5 3 2 1. Drain 2. Source 3. Gate 4, 5. Source Table 1. Device summary Order code Marking Package Packaging SD2933W SD2933 (1) M177 Plastic tray 1. For more details please refer to Chapter 6: Marking, packing and shipping specifications.. September 2013 DocID7193 Rev 14 1/16 This is information on a product in full production. www.st.com
Contents SD2933 Contents 1 Electrical data.............................................. 3 1.1 Maximum rating............................................. 3 1.2 Thermal data............................................... 3 2 Electrical characteristics..................................... 4 3 Impedance................................................. 5 4 Typical performance (30 MHz)................................. 6 4.1 Test circuit (30 MHz).......................................... 9 5 Package mechanical data.................................... 12 6 Marking, packing and shipping specifications................... 14 7 Revision history........................................... 15 2/16 DocID7193 Rev 14
Electrical data 1 Electrical data 1.1 Maximum rating T CASE = 25 C Table 2. Absolute maximum ratings Symbol Parameter Value Unit V (BR)DSS Drain source voltage 125 V V DGR Drain-gate voltage (R GS = 1MΩ) 125 V V GS Gate-source voltage ±20 V I D Drain current 40 A P DISS Power dissipation 648 W E AS Avalanche energy, single pulse (I D = 53 A, 800 µh coil) 1100 mj E (1) AR Avalanche energy, repetitive 50 mj T J Max. operating junction temperature 200 C T STG Storage temperature -65 to +150 C 1. Repetitive rating: Pulse width limited by maximum junction temperature / repetitive avalanche causes additional power losses that can be calculated as: P AV = E AR * f 1.2 Thermal data Table 3. Thermal data Symbol Parameter Value Unit R thj-c Junction to case thermal resistance 0.27 C/W DocID7193 Rev 14 3/16 16
Electrical characteristics SD2933 2 Electrical characteristics T CASE = 25 C Table 4. Static Symbol Test conditions Min. Typ. Max. Unit V (BR)DSS V GS = 0 V I DS = 200 ma 125 V I DSS V GS = 0 V V DS = 50 V 100 µa I GSS V GS = 20 V V DS = 0 V 500 na V (1) GS(Q) V DS = 10 V I D = 250 ma 1.5 4 V V DS(ON) V GS = 10 V I D = 20 A 3.0 V (1) G FS V DS = 10 V I D = 10 A see Table 5: G FS sort mho C ISS V GS = 0 V V DS = 50 V f = 1 MHz 1000 pf C OSS V GS = 0 V V DS = 50 V f = 1 MHz 372 pf C RSS V GS = 0 V V DS = 50 V f = 1 MHz 29 pf 1. V GS(Q) and G FS sorted with alpha/numeric code marked on unit. Table 5. G FS sort G FS sort Value A 10-10.99 B 11-11.99 C 12-12.99 D 13-13.99 E 14-14.99 F 15-15.99 G 16-16.99 H 17-18 Table 6. Dynamic Symbol Test Conditions Min. Typ. Max. Unit P OUT V DD = 50 V I DQ = 250 ma f = 30 MHz 300 400 W G PS V DD = 50 V I DQ = 250 ma P OUT = 300 W f = 30 MHz 20 23.5 db η D V DD = 50 V I DQ = 250 ma P OUT = 150 W f = 30 MHz 50 65 % Load mismatch V DD = 50 V I DQ = 250 ma P OUT = 300 W f = 30 MHz all phase angles 3:1 VSWR 4/16 DocID7193 Rev 14
Impedance 3 Impedance Figure 2. Impedance data schematic D Z DL Typical Input Impedance Typical Drain Load Impedance G Z IN S Table 7. Impedance data f Z IN (Ω) Z DL (Ω) 30 MHz 1.8 - j 0.2 2.8 + j 2.3 108 MHz 1.9 + j 0.2 1.6 + j 1.4 175 MHz 1.9 + j 0.3 1.5 + j 1.6 DocID7193 Rev 14 5/16 16
Typical performance (30 MHz) SD2933 4 Typical performance (30 MHz) Figure 3. Capacitance vs. drain voltage Figure 4. Drain current vs. gate voltage 10000 f= 1 MHz 15 Capacitance (pf) 1000 100 Ciss Coss Crss Id, Drain Current (A) 10 5 Vdd=10V Tc = + 25oC Tc = + 80oC Tc = - 20oC 10 0 10 20 30 40 50 Vds, Drain Source Voltage (V) 0 1 1.5 2 2.5 3 3.5 4 Vgs, Gate-Source Voltage (V) Figure 5. Gate-source voltage vs. case temperature Figure 6. Maximum thermal resistance vs. case temperature Vgs, GATE-SOURCE VOLTAGE (NORMALIZED) 1.15 1.1 1.05 1 0.95 0.9 0.85 Vdd= 10 V Id=.1 A Id= 15 A Id= 7 A Id= 4 A Id= 3 A 0.8-25 0 25 50 75 100 Tc, CASE TEMPERATURE (ºC) Id= 12 A Id= 10 A Id= 2 A Id= 1 A Id= 5 A Id=.25 A RTH(j-c) ( C/W) 0.33 0.32 0.31 0.3 0.29 0.28 0.27 0.26 25 30 35 40 45 50 55 60 65 70 75 80 85 Tc, CASE TEMPERATURE ( C) 6/16 DocID7193 Rev 14
Typical performance (30 MHz) Figure 7. Transient thermal impedance 0.30 0.25 0.20 Zth, Deg C / W 0.15 0.10 0.05 0.00 1.E-05 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 Rectangular power pulse width (sec) single pulse 10% 20% 30% 40% 50% 60% 70% 80% 90% AM10216V1 Figure 8. Transient thermal impedance model PR C PR C 1 R =.083 Ohm C =.0035904 F I_DC W atts PR C PR C 2 R =.099 Ohm C =.1182727 F PR C PR C 3 R =.088 Ohm C =2.4810922 F AM10217V1 DocID7193 Rev 14 7/16 16
Typical performance (30 MHz) SD2933 Figure 9. Output power vs. input power Figure 10. Output power vs. input power (at different temperature) Pout, Output Power (W) 500 400 300 200 100 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 Pin, Input Power ( W ) Vdd= 50 V Vdd= 40 V f= 30 MHz Idq=250mA Pout, Output Power (W) 500 400 300 200 100 Tc= 25 C f= 30 MHz Idq= 250 ma Vdd= 50 V 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 Pin, Input Power (W) Tc= -20 C Tc= 80 C Figure 11. Power gain vs. output power Figure 12. Efficiency vs. output power 26 Power Gain (db) 25 24 23 22 21 20 19 18 0 100 200 300 400 Pout, Output Power (W) f= 30 MHz Idq= 250 ma Vdd= 50 V Efficiency (%) 80 70 60 50 40 30 20 0 100 200 300 400 Pout, Output Power (W) f=30mhz Vdd=50V Idq=250mA Figure 13. Output power vs. supply voltage Figure 14. Output power vs. gate voltage 450 500 Pout, Output Power (W) 400 350 300 250 200 150 f = 30 MHz Idq = 250 ma Pin = 2.6 W Pin = 1.3 W Pin = 0.65 W Pout, OUTPUT POWER (W) 400 300 200 100 F= 30 MHz Vdd= 50 V Idq= 250 ma Pin= constant Tc= +25 C Tc= -20 C Tc= +80 C 100 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Vdd, Supply Voltage (V) 0-3 -2-1 0 1 2 3 Vgs, GATE-SOURCE VOLTAGE (V) 8/16 DocID7193 Rev 14
Typical performance (30 MHz) 4.1 Test circuit (30 MHz) Figure 15. 30 MHz test circuit schematic Table 8. Transmission line dimensions Dim. Inch mm A 0.532 13.51 B 0.250 6.35 C 0.181 4.59 D 0.383 9.37 E 0.351 8.91 F 0.633 16.08 G 0.477 12.12 H 0.438 11.12 J 0.200 5.08 K 0.164 4.16 L 0.174 4.42 M 0.817 20.75 N 0.350 8.89 P 0.779 19.79 R 0.639 16.23 DocID7193 Rev 14 9/16 16
Typical performance (30 MHz) SD2933 Table 8. Transmission line dimensions (continued) Dim. Inch mm S 0.165 4.19 T 1.017 25.84 U 0.375 9.52 V 0.456 11.58 W 0.325 8.24 X 0.650 16.50 Table 9. 30 MHz test circuit part list Component Description C1,C9 0.01 μf / 500 V surface mount ceramic chip capacitor C2, C3 750 pf ATC 700B surface mount ceramic chip capacitor C4 C5,C10,C11,C14,C16 C6 C7 C8 C12 C13 C15 R1,R3 R2 T1 T2 L1 L2 RFC1,RFC2 FB1 FB2 PCB 300 pf ATC 700B surface mount ceramic chip capacitor 10000 pf ATC 200B surface mount ceramic chip capacitor 510 pf ATC 700B surface mount ceramic chip capacitor 300 pf ATC 700B surface mount ceramic chip capacitor 175-680 pf type 46 standard trimmer capacitor 47 μf / 63 V aluminum electrolytic radial lead capacitor 1200 pf ATC 700B surface mount ceramic chip capacitor 100 μf / 63 V aluminum electrolytic radial lead capacitor 1 K OHM 1 W surface mount chip resistor 560 OHM 2 W wire-wound axis lead resistor HF 2-30 MHz surface mount 9:1 transformer RG - 142B/U 50 OHM coaxial cable OD = 0.165[4.18] L 15 [381.00] covered with 15 [381.00] tinned copper tubular brand 13/65 [5.1] width 1 3/4 turn air-wound 16 AWG ID = 0.219 [5.56] poly-coated magnet wire 1 3/4 turn air-wound 12 AWG ID = 0.250 [6.34] bus bar wire 3 turns 14 AWG wire through ferrite toroid Surface mount EMI shield bead Toroid ULTRALAM 2000. 0.030 THK, εr = 2.55, 2 Oz ED CU both sides 10/16 DocID7193 Rev 14
Typical performance (30 MHz) Figure 16. 30 MHz test circuit photomaster 4 inches 6.4 inches Figure 17. 30 MHz test circuit DocID7193 Rev 14 11/16 16
Package mechanical data SD2933 5 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Table 10. M177 (.500 dia 4/L N/HERM W/FLG) mechanical data Dim. mm Inch Min. Typ. Max. Min. Typ. Max. A 5.72 5.97 0.225 0.235 B 6.73 6.96 0.265 0.275 C 21.84 22.10 0.860 0.870 D 28.70 28.96 1.130 1.140 E 13.84 14.10 0.545 0.555 F 0.08-0.18 0.003-0.007 G 2.49 2.74 0.098 0.108 H 3.81 4.32 0.150 0.170 I 7.11 0.280 J 27.43 28.45 1.080 1.120 K 15.88 16.13 0.625 0.635 12/16 DocID7193 Rev 14
Package mechanical data Figure 18. M177 package dimensions (a) a. Controlling dimensions in inches. DocID7193 Rev 14 13/16 16
Marking, packing and shipping specifications SD2933 6 Marking, packing and shipping specifications Table 11. Packing and shipping specifications Order code Packaging Pcs per tray Dry pack humidity GFS code Lot code SD2933W Plastic tray 25 < 10% Not mixed Not mixed Figure 19. Marking layout for SD2933W Table 12. Marking specifications Symbol Description W X CZ xxx VY MAR CZ y yy Wafer process code G FS sort Assembly plant Last 3 digits of diffusion lot Diffusion plant Country of origin Test and finishing plant Assembly year Assembly week 14/16 DocID7193 Rev 14
Revision history 7 Revision history Table 13. Document revision history Date Revision Changes 30-Jul-2004 9 22-Sep-2011 10 Inserted Section 6: Marking, packing and shipping specifications. Updated EAS in Table 2: Absolute maximum ratings. Minor text changes to improve readability. 03-Oct-2011 11 Updated parameter Z IN in Table 7: Impedance data. 17-Nov-2011 12 Inserted Figure 7: Transient thermal impedance and Figure 8: Transient thermal impedance model. 10-Jan-2012 13 Updated Figure 7: Transient thermal impedance. 30-Sep-2013 14 Added row for Avalanche energy, repetitive and footnote to Table 2: Absolute maximum ratings Minor text and formatting changes DocID7193 Rev 14 15/16 16
Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16 DocID7193 Rev 14