Z-E3756 INSTALLATION MANUAL EN
COMPATIBILITY LIST Model Model Version Model Year FIAT Ducato III 250/251 2006 2011 FIAT Ducato III 250/251 2011 2014 FIAT Ducato III 250/251 from 2014 Citroën Jumper II 250/250D/250L from 2006 Peugeot Boxer II 250/251 from 2006 CAUTION The installation of the ZENEC system should be carried out by an authorized installer. Specific knowledge and tools are required to do the installation. Incorrect installation can cause damage to the vehicle and the ZENEC system. Correct functioning can only be guaranteed when you use the ZENEC original accessories included in the kit or optionally available. The ZENEC system and the original accessories must under no circumstance be modified or altered. Inappropriate actions can cause damage to the vehicle and the ZENEC system. NOTE The target vehicle must offer factory provision for the installation of a radio. The ZENEC system is not compatible with vehicles that are equipped with an OE radio or OE navigation system ex works. This device installation manual applies to vehicle platforms appearing in the above compatibility list, and in a condition as offered by the respective vehicle manufacturer. Other differing configurations and installations of motorhome manufacturers are not covered by this installation manual. If you have questions or vehicle-specific problems please contact the relevant motorhome manufacturer. The ZENEC system is equipped with an integrated DAB+ receiver. To make use of this tuner system you will need a suitable DAB antenna (not included in kit) that must be connected to the ZENEC system. If the target vehicle is equipped with a multifunction steering wheel, in order to support the steering wheel remote functions a stalk interface is required (separate accessory). Software updates to the ZENEC system are installed with a USB memory device. Therefore when fitting the system make sure that the USB connection of the ZENEC system will still be accessible later (installation of USB extension cable or USB hub). If you have questions or problems relating to the ZENEC system, please contact the dealer from whom you purchased it. THE KIT INCLUDES No. Article Qty 1 ZENEC system 1 2 Mounting frame 1 3 Phillips screws 4 4 Remote control 2 5 microsd card with adapter 1 6 GPS antenna 1 7 Bluetooth microphone 1 8 Antenna adapter ISO/DIN 1 9 Main connection cable 1 10 USB extension cable 2 11 24-pin connection cable (4.2, MZone, AV-IN) 1 12 20-pin connection cable (Mic, Cam, IR-IN) 1 13 Connection cable parking brake 1 14 Metal plate for GPS antenna 1 15 Double-sided adhesive pad 1 TOOLS REQUIRED Torx screwdriver T25 Phillips screwdriver Release tool made of plastic Hand saw or equivalent File Insulating tape 2
REMOVAL WORK AND PREPARATION: 1 1. Remove both storage compartments in accordance with the manufacturer s information. 2.a 2.a Cut off the left and right plastic holders for the storage compartments as flush as possible. 2.b 2.b Use a suitable saw to do this, and then a file to remove any protrusions still present. INSTALLATION: 3 3. Remove the two original Torx screws at the top (T25). 3
4 4. Before installing the ZENEC system (No. 1) remove the two transport securing screws of the loader mechanism. 5.a 5.a Insert the mounting frame (No. 2) at an angle from above into the radio slot. 5.b 5.b Screw down the mounting frame at the top and bottom with the four Phillips screws (No. 3) supplied with the ZENEC system kit. 6. (No picture) Fit the GPS antenna (No. 6) at a suitable place, and make sure that the GPS reception is not adversely affected due to shadowing by metallic vehicle parts (thermal glazing etc.). Use the metal plate supplied as a base for the GPS antenna to improve its reception, depending on the situation. Next, run the connecting cable to the radio slot. 7. (No picture) If you wish to use it, fit the external Bluetooth microphone (No. 7) in a suitable location, and run the connecting cable to the radio slot. Depending on your choice of an external or device-internal microphone, the microphone source for the Bluetooth mode must be correspondingly changed in the device menu. 8. (No picture) Run the USB extension cable (No. 10) from the radio slot to the position you want. 4
9 9. Connect the main cable (No. 9) of the ZENEC system (No. 1) to the ISO plug connectors of the vehicle. 10 10. Connect all the cables to the ZENEC system (No. 1): those previously run in the radio slot, and the original antenna cable. If necessary, use the ISO DIN antenna adapter (No. 8) included in the kit. Next slide the ZENEC system carefully into the radio slot until it locks in place. NOTE Make sure that all connectors at the rear of the unit have sufficient room and are not bent. For vehicles with an original FIAT active antenna, it is necessary to ensure a power supply for the antenna. Pay particular attention that the plug connectors of the P.ANT lead of the main connection cable (No. 9) are connected together. Connectors without a retaining mechanism must be secured with insulating tape. COMMISSIONING Make sure that the vehicle is outside, and that the GPS reception is not adversely affected by any shadowing (trees, high buildings etc.). Now insert the navigation software SD card (No. 5) supplied into the SD card slot of the ZENEC system, and start it in order to establish a sat fix. Make sure that the vehicle is not moved until the sat fix is established. Now press the NAV button to start the navigation mode, and choose map view. Once your present location is shown means, the sat fix has been established sucessfully. This can take 3 to 5 minutes. You can now use the ZENEC system. Finally carry out a general functional test, and make the basic settings. Also ensure that no fault warnings appear on the vehicle side. 5
CONNECTION DIAGRAM D GPS Bluetooth Antenna A DAB FM (see note on DAB antenna page 2) C E HDMI USB 1/2 A1 A3 A5 A7 A2 A4 A6 A8 A9 A11 A13 A15 A10 A12 A14 A16 A1 KL 31 / Power GND A2 KL 30 / Permanent +12V PWR A3 KL 15 / Switched +12V PWR A4 Illumination A5 Switched +12V amp PWR* A6 Parking A7 Switched +12V antenna PWR A8 Reverse gear A9 Loudspeaker rear right (+) A10 Loudspeaker front right (+) A11 Loudspeaker right (-) A12 Loudspeaker front right (-) A13 Loudspeaker rear left (+) A14 Loudspeaker front left (+) A15 Loudspeaker rear left (-) A16 Loudspeaker front left (-) *300mA max. B2 B1 B4 B3 B6 B5 B8 B7 B9 B10 B11 B12 B13 B14 B15 B16 B1 N.A. B2 N.A. B3 KL 30 / Permanent +12V PWR B4 N.A. B5 Illumination B6 Switched +12V antenna PWR B7 KL 31 / Power GND B8 KL 15 / Switched +12V PWR B9 Loudspeaker rear right (-) B10 Loudspeaker rear right (+) B11 Loudspeaker front right (-) B12 Loudspeaker front right (+) B13 Loudspeaker front left (-) B14 Loudspeaker front left (+) B15 Loudspeaker rear left (-) B16 Loudspeaker rear left (+) A E C C D A B B P. CNTR Parking Reverse ext. Mic Speed In IR In CAM 1 Power 300mA GND CAM 2 Power 300mA GND CAM 3 Power 300mA GND CAM Audio In CAM 1 CVBS In Camera CAM 2 CVBS In CAM 3 CVBS In Line In R Line In L A/V In Video In Front Out R Front Out L Rear Out R Line Out Rear Out L Subwoofer Out Subwoofer Out Video Out 1 Video Out 2 Line Out R Line Out L ZENEC Bohrturmweg 1 CH-5330 Bad Zurzach Schweiz/Switzerland Mail: support@zenec.com www.zenec.com M-Zone Input (reserved for Schaudt) Technical modifications excepted. No liability granted for printing errors. Copyright 2018 RevA / copy deadline: Q1-2018 English