Installation instructions for part
|
|
- Ellen Cameron
- 6 years ago
- Views:
Transcription
1 Installation instructions for part KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Hyundai Table of Contents Dash Disassembly KIT COMPONENTS A) Radio housing B) Radio brackets C) Spacers, thick and thin D) (4) #10 x 3/4 Phillips screws E) Pocket F) (4) #8 x 3/8 Phillips screws A B C D E F. Hyundai Elantra (with double DIN radio) Hyundai Santa Fe Hyundai Sonata Hyundai Tiburon (with double DIN radio) Kit Assembly. ISO DIN radio provision with pocket ISO DDIN radio provision... 7 REV. 4/20/2016 INST WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: (Santa Fe with a Monsoon amp) Antenna Adapter: Not required 40-GM 10 (Santa Fe with a Monsoon amp) TOOLS REQUIRED Panel removal tool Phillips screwdriver thick thin CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. METRA. The World s best kits. metraonline.com COPYRIGHT METRA ELECTRONICS CORPORATION
2 Elantra (with double DIN radio) Unclip and remove the dimmer switch panel, and then remove (1) Phillips screw exposed behind the panel. (Figure A) 2. Unclip and remove the shifter trim panel. 3. Remove (1) Phillips screw at the bottom of the radio trim panel. (Figure C) 4. Unclip and remove the temperature control cable under the drivers side of the dash from the white plastic bracket. 5. Remove (4) Phillips screws securing the radio, and then remove the radio. (Figure A) Dash Disassembly (Figure C) 2
3 Dash Disassembly Santa Fe Remove the ashtray, and then remove (2) Phillips screws now exposed in the cavity. (Figure A) 2. Unclip and remove the climate control panel. 3. Remove (2) Phillips screws facing up at bottom of radio trim panel. (Figure C) 4. Unclip and remove the radio trim panel. (Figure D) 5. Remove (4) Phillips screws securing the radio, and then remove the radio. (Figure A) (Figure C) (Figure D) 3
4 Dash Disassembly Sonata Sonata Unclip and remove the trim panel around the shifter. (Figure A) 2. Remove (1) Phillips screw at the bottom of the radio trim panel. 3. Unclip and remove the radio trim panel. 4. Remove (4) Phillips screws securing the radio, and then remove the radio. (Figure A) 1. Unclip and remove the trim panel in front of the shift lever, and then remove (2) Phillips screws exposed underneath. (Figure A) 2. Unclip and remove the shift lever trim panel. (Figure A) 3. Remove (2) Phillips screws at the bottom of radio trim panel. 4. Unclip and remove the radio trim panel. 5. Remove (4) Phillips screws securing the radio, and then remove the radio. (Figure A) A B 4
5 Dash Disassembly Tiburon (with double DIN radio) Unclip and remove the panel surrounding the shift lever. (Figure A) 2. Unclip and remove the radio trim panel. 3. Remove (2) Phillips screws securing the radio, and then remove the radio. (Figure A) 5
6 Kit Assembly ISO DIN radio provision with pocket 1. Attach the appropriate spacer (see legend below) between the radio housing and the radio brackets, aligning the holes in the radio housing to the clips on the radio brackets. (Figure A) 2. Attach the pocket to the lower section of the radio brackets using the (4) #8 x 3/8 Phillips screws provided. 3. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 4. Slide the radio into the bracket/pocket assembly, and then secure using the screws supplied with the radio. 5. Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Test the radio for proper operation. 6. Reassemble the dash in reverse order of disassembly. (Figure A) Legend For the Hyundai Sonata , Hyundai Tiburon (with double DIN radio) , and the Hyundai Santa Fe vehicles, use the provided thick spacers. For the Elantra (with double DIN radio) vehicles, use the provided thin spacers. The spacers will need to be removed from the shipping bar. 6
7 Kit Assembly ISO DDIN radio provision 1. Attach the appropriate spacer (see legend below) between the radio housing and the radio brackets, aligning the holes in the radio housing to the clips on the radio brackets. (Figure A) 2. Slide the radio into the assembly and then secure using the screws supplied with the radio. 3. Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Test the radio for proper operation. 4. Reassemble the dash in reverse order of disassembly. (Figure A) Legend For the Hyundai Sonata , Hyundai Tiburon (with double DIN radio) , and the Hyundai Santa Fe vehicles, use the provided thick spacers. For the Elantra (with double DIN radio) vehicles, use the provided thin spacers. The spacers will need to be removed from the shipping bar. 7
8 Installation instructions for part IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. REV. 4/20/2016 INST KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World s best kits. metraonline.com COPYRIGHT METRA ELECTRONICS CORPORATION
Porsche 911 (996) Porsche Boxster (986) B
INSTALLATION INSTRUCTIONS FOR PART 99-9605B Porsche 911 (996) 1999-2005 Porsche Boxster (986) 1997-2004 99-9605B KIT FEATURES ISO DIN radio provision with pocket (NAV models only) ISO DDIN radio provision
More informationChevy Prizm / Toyota Corolla
99-3413 INSTALLATION INSTRUCTIONS KIT COMPONENTS A) Radio housing B) (2) #10 x 3/4 Phillips screws A B Chevy Prizm 1998-2003 / Toyota Corolla 1998-2002 KIT FEATURES DIN radio provision Retains the factory
More informationNissan Titan 2017-up, Titan XD 2016-up B
INSTALLATION INSTRUCTIONS FOR PART 95-7631B Nissan Titan 2017-up, Titan XD 2016-up 95-7631B Table of Contents Dash Disassembly...2-5 Kit Assembly. ISO DDIN radio provision... 6 KIT FEATURES ISO DDIN radio
More informationAcura/Honda/Isuzu
INSTALLATION INSTRUCTIONS FOR PART 95-7801 KIT FEATURES Double DIN radio provision Stacked ISO radio provision APPLICATIONS See application list inside Acura/Honda/Isuzu 1990-2006 95-7801 WIRING & ANTENNA
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS Toyota Matrix Pontiac Vibe
INSTLLTION INSTRUCTIONS FOR PRT 99-8205 KIT FETURES DIN head unit provision ISO DIN head unit provision DDIN head unit provision - Excluding 2005-2008 Matrix Stacked ISO DIN head unit provision - Excluding
More informationINSTALLATION INSTRUCTIONS
3b Fig. A Fig. C Fig. B Fig. D KIT FEATURES ISO and DIN unit provisions Pocket (holds jewel cases) KIT COMPONENTS Radio Housing 99-7898 INSTALLATION INSTRUCTIONS APPLICATIONS ACCORD 990-97, CIVIC 999-00,
More informationINSTALLATION INSTRUCTIONS FOR PART TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool Phillips Screwdriver Socket Set
INSTLLTION INSTRUCTIONS FOR PRT 99-65 PPLICTIONS Chrysler Sebring 007 Chrysler Town and Country 008 Dodge venger 007-008 Dodge Dakota 008 Dodge Grand Caravan 008 Dodge Nitro 007 Jeep Wrangler 007 (Modifications
More informationFord/Jeep/Lincoln/Mercury
Installation instructions for 99-5510 KIT FEATURES DIN radio provision APPLICATIONS See application list inside Ford/Jeep/Lincoln/Mercury 1975-2000 99-5510 WIRING & ANTENNA CONNECTIONS (sold separately)
More information16-pin harness with stripped leads Female 3.5mm connector with stripped leads
AX-HYKIA1-SWC INSTALLATION INSTRUCTIONS Hyundai/Kia Data Interface with SWC 2010-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications. INTERFACE FEATURES Provides NAV outputs (parking
More informationAX-HYKIA3-SWC. OPTIONAL ACCESSORIES (sold separately) SPDIF Interface: AX-HYKIA-SPDIF interface. APPLICATIONS See inside front cover
AX-HYKIA3-SWC INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-HYKIA3-SWC interface AX-HYKIA3-SWC harness AX-CAM6V 16-pin harness with stripped leads Female 3.5mm connector with stripped leads OPTIONAL
More informationINSTALLATION INSTRUCTIONS
KIT FEATURES ISO Stack and Double-DIN head unit provisions KIT COMPONENTS 99-780 INSTALLATION INSTRUCTIONS ACURA CL 997-99 Radio Housing Rear Support Tray Mounting Bracket (ACURA Legend) ISO Brackets ()
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. A) Radio Housing I B) ISO Snap-In Brackets I C) Trim Plates (upper & lower) TOOLS REQUIRED:
INSTLLTION INSTRUCTIONS FOR PRT 99-6507 99-6507 KIT FETURES DIN Radio Provision with Pocket ISO DIN Radio Provision with Pocket KIT COMPONENTS Dodge Caliber 007 Charger 005-007 Dakota 005-007 Durango 00-007
More informationAX-AM-GM91. GM HDMI and Camera Interface 2013-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
AX-AM-GM91 INSTALLATION INSTRUCTIONS GM HDMI and Camera Interface 2013-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications. INTERFACE FEATURES Provides front and rear camera inputs
More informationInstallation instructions for part AX-MB1-SWC
Installation instructions for part REV. 11/18/2016 INST Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory power) Provides NAV outputs (parking brake, reverse, and speed sense)
More informationAW-200GM APPLICATIONS GM MULTI KIT KIT FEATURES KIT COMPONENTS A B C TOOLS REQUIRED:
APPLICATIONS GM MULTI KIT 99-2001 AW-200GM KIT FEATURES DIN Head Unit w/ Equalizer Provision KIT COMPONENTS A) Radio Housing B) Spacer C) Equalizer Dummy Plate D) Shaft Masks A B C D TOOLS REQUIRED: Phillips
More informationAX-HYKIA4-SWC. Retains the factory AUX-IN jack Retains the factory backup camera Retains balance Micro-B USB updatable
AX-HYKIA4-SWC INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS AX-HYKIA4-SWC interface AX-HYKIA4-SWC harness AX-HYKIA-SPDIF interface 16-pin harness with stripped leads Female 3.5mm connector with stripped
More informationAX-TYAMP2-SWC. Toyota Amp Interface with SWC 2012-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
AX-TYAMP2-SWC INSTALLATION INSTRUCTIONS Toyota Amp Interface with SWC 2012-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications. INTERFACE FEATURES Retains audio controls on the
More informationAxxess Steering Wheel Control interface for select Toyota and Lexus vehicles
INSTALLATION INSTRUCTIONS FOR PART ASWC-TOY-LEX ASWC-TOY-LEX Axxess Steering Wheel Control interface for select Toyota and Lexus vehicles INTERFACE COMPONENTS ASWC-TOY-LEX interface 12-pin harness with
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Chrysler Multi Kit. Chrysler/Dodge/Eagle/Jeep/Plymouth TOOLS REQUIRED:
INSTALLATION INSTRUCTIONS FOR PART 99-9 KIT FEATURES DIN Mount Radio Provision APPLICATIONS Chrysler Multi Kit Chrysler/Dodge/Eagle/Jeep/Plymouth 9-00 NOTE: It may be necessary to modify the back of the
More informationMITSUBISHI DATA BUS INTERFACE MITO-01 INSTALLATION INSTRUCTIONS
MITSUBISHI DATA BUS INTERFACE INSTALLATION INSTRUCTIONS * READ IMPORTANT WARNING ON PAGE 2 BEFORE ATTEMPTING ANY INSTALLATION The is designed to be used in vehicles listed in the applications that have
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,,1999,2000. & nstall Factory Radio
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print options
More informationWildcat XX Stage 1 Audio Kit
2436-466 Wildcat XX Stage 1 Audio Kit WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: Factory Radio with dash radio installation kit 1) Select FLE then PRNT
More information1997 I Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws.,1998,1999,2000. Factory Radio
More informationGMC - Jimmy Chevy - S-10 / S-15 Series Olds - Bravado
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationInstallation Instructions
86-95 Samurai Blower Motor Switch (SKU# SIB-HBS) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and equipment. Suggested Tools:
More informationAX-TYAMP1-SWC Lexus/Toyota Amp Interface with SWC
Installation instructions for part Lexus/Toyota Amp Interface with SWC 2002-2015 Provides accessory power (12-volt 10-amp) Retains audio controls on the steering wheel Provides NAV outputs (parking brake
More informationF-Series Trucks - Ford Full Size Bronco - Ford
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationBMW E90 Android Touch Screen Radio Installation Instructions
BMW E90 Android Touch Screen Radio Installation Instructions Enjoy your new Android Radio from Bremmen Parts, we appreciate your business. Vibrant Touch Display This radio features a responsive 9 touch
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More informationI Click on a link tab to jump to that page. Cover Page
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print options
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationREMOVAL/INSTALL INSTRUCTIONS: REPLACEMENT RADIO BUTTONS
REMOVAL/INSTALL OF RADIO BUTTONS (Part# 76822) GM Vehicles 2003-2007 General Tech Tips: Work in a location that is clean & static-free (static discharge has the potential to permanently damage electrical
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: Factory Radio with dash radio installation kit 1) Select FLE then PRNT
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationFull Size Pick Ups - GM Suburban/Yukon/Tahoe - GM Escalade - Cadillac Click on a link tab to jump to that page.
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford Explorer 1996-2001, Ford Explorer SportTrac 2001, Ford Ranger 1996-2001, Mazda B-2500\B-3000\B-4000 1998-2001, Mercury Mountaineer 1997-2001 THE safety accessory
More informationTOYOTA TACOMA BED EXTENDER Preparation. Part Number: PT
Preparation Part Number: PT392-35120 Kit Contents 1 1 Curved Tube Assembly - Right 2 1 Curved Tube Assembly - Left 3 3 Center Tube 4 1 Hardware Bag 5 1 Installation Instructions 6 1 Care Card Hardware
More informationTOYOTA COROLLA EC REARVIEW MIRROR Section I Installation Preparation
Section I Installation Preparation Part Number: PT374-02030 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass & Maplights 2 1 Hardware Bag
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationWritten By: Walter Galan
Replace the small antenna attached to the headphone jack of your iphone 4S. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION Use this guide to replace your iphone's
More informationWritten By: Walter Galan
iphone 4S Logic Board Replacement Replace a dead logic board in your iphone 4S. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Use this guide to replace your iphone's
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Toyota RAV4 1996-2000 THE safety accessory of the 21 st Century. P/N 210-0034-0 Rev B1 (11-19-02), GG 2002 Muth Co. LLC. Note: Professional Installation Recommended
More informationWritten By: Walter Galan
iphone 4 Logic Board Replacement Replace a dead logic board in your iphone 4. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION Use this guide to replace your iphone
More informationTOYOTA TACOMA BED EXTENDER Preparation. Part Number: PT General Applicability All 2012 and newer Tacoma models
Preparation Part Number: PT392-35120 Kit Contents 1 1 Curved Tube Assembly - Right 2 1 Curved Tube Assembly - Left 3 3 Center Tube 4 1 Hardware Bag 5 1 Installation Instructions 6 1 Care Card Hardware
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More information1999 I Click on a link tab to jump to that page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,,2000. Factory Radio
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationRef Qty Part Description Part Number 1 1 Headlight-LED Nylon Tie Strap Instructions
LED LIGHTS KIT P/N 2880289; 2880621 APPLICATION MY15-16 INDIAN MOTORCYCLES WITH THUNDERSTROKE 111 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationWritten By: Walter Galan
iphone 4 Vibrate Ring Switch Replacement Replace the metal portion of the vibrate/ring switch on your iphone 4. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION Use
More informationDoor window. Front door window, assembly overview
64-50 Door window Front door window, assembly overview 1 - Window channel Pushed onto flange 2 - Door window Removing Page 64-52 Adjusting Page 64-53 3 - Door 4 - Outer window channel Pushed onto flange
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationSB-F-MUSCPE/12TW3 SKU# Up Ford Mustang Coupe
If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly
More informationProduct: GenX Mobile 5p Device
Product: GenX Mobile 5p Device Installation Guide Version 2.1 Date: October 24, 2016 Distribution: GPS Customers Page 1 of 11 Contents Installation Guide... 1 Introduction... 3 Antenna Options... 3 Device
More informationAUGMENT THE WEIGHT STACK SELECTION PRO SELECTION PRO MED INSTALLATION MANUAL
AUGMENT THE WEIGHT STACK SELECTION PRO SELECTION PRO MED INSTALLATION MANUAL REV 1.0 LANG: ENG DATE: 2016.06.03 1/33 SOMMARIO 1 INFORMATION NOTE... 4 2 TOOLS... 4 3 PERSONAL PROTECTIVE EQUIPMENT... 4 4
More informationSIGNATURE FRONT BUMPER INSTALL
SIGNATURE FRONT BUMPER INSTALL JL **PLEASE READ THROUGH THE INSTRUCTIONS BEFORE BEGINNING ANY PART OF THE INSTALLATION PROCESS** 1. You can now remove the trim strip (2 vertical clips, 4 horizontal, 2
More informationPreference Collection 5543 Central Console INSTALLATION GUIDE
Preference Collection 5543 Central Console INSTALLATION GUIDE WARNING Failure to install the 5543 as described in this installation guide may cause the unit to collapse, resulting in serious injury to
More informationUniden CB Radio PRO 510XL (87-18 Wrangler YJ, TJ, JK & JL)
Installation Time: 60-90 Minutes Tools Required: Phillips Screw Driver Drill (with drill bit set) Multimeter Tester Electrician s Stripper/Cutter Uniden CB Radio PRO 510XL (87-18 Wrangler YJ, TJ, JK &
More informationiphone 4S Dismantling Instructions
iphone 4S Dismantling Instructions These instructions will show you how to open the iphone to replace the digitizer, LCD screen and other internal parts. Opening your iphone will void your warrantee, and
More informationSimply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware.
2 Simply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware. Apply masking tape to the top of the bumper cover underneath
More informationAssembly Instructions for Laser Sailboat Dolly (with Beach Wheels for 1 Axle & Ramp Wheels with Reversible Axle)
Assembly Instructions for Laser Sailboat Dolly (with Beach Wheels for 1 Axle & Ramp Wheels with Reversible Axle)! IMPORTANT: Before you begin, please read these instructions and check to be sure that all
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationWritten By: Jeff Suovanen
iphone 8 Battery Replacement Replace the battery in your iphone 8 if it has failed, swollen, or no longer holds sufficient charge. Written By: Jeff Suovanen ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More information1 of 2 3/3/2017 4:49 PM
1 of 2 3/3/2017 4:49 PM Front Door Window, Assembly Overview 1 - Window guide - Inserted on flange 2 - Door 3 - Inner window recess seal - Inserted on flange 4 - Bolt - 20 Nm 5 - Carrier assembly - Window
More informationREMOVAL/INSTALL INSTRUCTIONS: REPLACEMENT RADIO BUTTONS
REMOVAL/INSTALL OF RADIO BUTTONS (Part# 76824) GM Vehicles 2003-2007 General Tech Tips: Work in a location that is clean & static-free (static discharge has the potential to permanently damage electrical
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-845) Chevrolet S10 Blazer/Pickup, GMC S15 Jimmy/Pickup 1995 2004, Oldsmobile Bravada 1996 2001, GMC Envoy 1998 2000, Isuzu Hombre 1998 2000 General Tech Tips: Use
More informationRMD5000 Rackmount Kit Instructions
xx ZZZ RMD5000 Rackmount Kit Instructions www.tektronix.com *P075102000* 075-1020-00 Copyright Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers,
More informationTaurus - Ford Sable - Mercury
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationWritten By: Arthur Shi
iphone 8 Taptic Engine Replacement Replace the Taptic Engine in an iphone 8. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION The Taptic Engine produces your iphone's
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationUnder Seat Storage Drawer Installation Instructions
Under Seat Storage Drawer Installation Instructions Parts List: 1) Drawer Assembly 8) Self Tapping Screws 1) Instructions 1) Template Tools Needed: Drill and/or Bit Driver Tape Measure Jigsaw or metal
More informationReplacing the PCM Instruction Sheet
Replacing the PCM Instruction Sheet INTRODUCTION Use the following instructions when replacing or upgrading a Processor Control Module (PCM) in CP2000-ZX and CP2000-M/MR projectors. The entire procedure
More informationWritten By: Andrew Optimus Goldberg
Replace the screen your GSM/AT&T iphone 4. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION [video: http://www.youtube.com/watch?v=obpfpfx5abw] Use this guide
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationRugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)
Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7
More informationMANUAL INSTALLATION. Linear Bar Grille - Heavy Duty LBPH/LBMH. v000 Issue Date: 09/17/ Price Industries Limited. All rights reserved.
MANUAL INSTALLATION Linear Bar Grille - Heavy Duty LBPH/LBMH v000 Issue Date: 09/17/18 2018 Price Industries Limited. All rights reserved. TABLE OF CONTENTS Product Overview Overview...1 Before You Start...2
More informationINSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series
INSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories The KTP-Series is a free standing, pole mount solution for multiple displays. KTP-320 KTP-220 / KTP-225 KTP-440 / KTP-445
More informationMODULAR BUMPER INSTALLATION MANUAL
MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationNAVIGATION SYSTEM INSTALLATION INSTRUCTIONS
NAVIGATION SYSTEM INSTALLATION INSTRUCTIONS These instructions along with the pictures were performed in a 2008 Yukon. Please use them only as a reference since they might not exactly match your vehicle
More informationWARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD!
WARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD! THIS KIT INCLUDES: 4 M8-1.25X30MM BOLTS WITH WASHERS 12 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOULDER BOLTS WITH RIGHT AND
More informationRM4000 Tektronix 4000 Series Rackmount Kit
Instructions RM4000 Tektronix 4000 Series Rackmount Kit 071-2134-01 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless
More informationWritten By: Jeff Suovanen
iphone 8 Plus Taptic Engine Replacement Replace the Taptic Engine (haptic vibration motor) in an iphone 8 Plus. Written By: Jeff Suovanen ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION The
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2005-2010 Chevy Corvette C6 THE safety accessory of the 21 st Century. P/N 210-0144-0 Rev. A3 (9/29/2011), BTV 2007 Muth Mirror Systems, LLC Page 3 of 10PplPage
More informationFerrari 348 GTS Door Mirror Removal and Disassembly
Ferrari 348 GTS Door Mirror Removal and Disassembly Removing the mirror Remove the triangular trim plate from inside the door (3 self-tappers). Be careful not to damage the rubber coating - this trim is
More informationMicro Channel. Shorten the Fixture (optional) Installation Instructions for 700UMCD_ UNILUME. This product is suitable for damp locations.
Installation Instructions for Micro Channel 700UMCD_ 90MICRO. UNILUME GENERAL PRODUCT I NFORMATION: This product is suitable for damp locations. This product can be dimmed with a low-voltage electronic
More informationBX-GM6 GM LAN-11 Data Interface
Installation instructions for BX-GM6 REV. 3/2/2016 INSTBX-GM6 BX-GM6 GM LAN-11 Data Interface 2006-2012 FEATURES Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory power) Retains
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSuggested Instructions for: , , , C5 Emergency Brake Boot
Suggested Instructions for: 608-348, 608-349, 614-653, 619-200 C5 Emergency Brake Boot Tools Ratchet, 10mm socket, extension #15 Torx screwdriver Needle nose pliers Masking Tape Very small flat head screwdriver
More informationASSEMBLY & INSTALLATION MANUAL Trim Kit for Evo Affinity 30G
the natural way to cook ASSEMBLY & INSTALLATION MANUAL ( Shown installed to granite topped cabinet ) Copyright 2013 THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND, AND FOLLOW THE INSTRUCTIONS
More information