4 Lindapter s support fixing range offers a series of ideal solutions for all building services. This includes the suspension of HVAC equipment, pipe work, fire protection/sprinkler systems, suspended ceilings and all manner of electrical equipment such as cable tray and ladder. These products have all been designed to give speed and ease of installation to reduce time and keep costs under control. Where necessary support products have been tested, and approved, by the relevant bodies such as those which oversee and insure fire protection installations. For the installation of heavy duty service equipment such as pipe supports used in the petro chemical industry the steelwork fixings in section 1 of this catalogue are more suitable. 54
4 High Grade Alloy Steel, bright zinc plated Setscrew Locknut Nut Basket T Swivel Unit W U R 360º Beam flange clamp with swivel unit. For parallel and sloping flanges. Supplied with grade 8.8 setscrew for secure grip. (4:1 Factor of Safety) Torque Product Thread Tensile/ 25º Tensile/> 25º to 45 Clamping Thickness Setscrew Setscrew Nut Dimensions Code W N R T U Width kn kn mm Nm Nm mm mm mm mm mm FLS08 M8 2.5 1.5 3-17 M10 18 18 55 53 58 27 28 FLS10 M10 2.5 1.5 3-17 M10 18 18 55 53 58 27 28 Order example: FLS08 Installation Approved Applications N M 1. 2. 3. 4. S 25 25 25 1. Locate FLS onto flange. 2. Ensuring lug on locknut locates into main body, tighten down setscrew (), and then tighten upper locknut (N). 3. Install threaded rod by screwing into nut located in nut basket (S). Ensure full thread capture. 4. Secure assembly in nut basket (S) from beneath using a locknut (not supplied). General Applications Parallel Flanges only 90 Ensure that the cup point setscrew always grips on the tapered side of the flange. 45 45 55
4 Malleable iron, bright zinc plated Hexagon Setscrew Square Head Setscrew Rear Hole (Tapped / Clear) Locknut Main Body T N V W U Beam Clamp suitable for use with parallel or tapered flange beams, supplied with the back hole drilled or tapped. The type FL uses a grade 8.8 cup point setscrew for secure grip. Supplied with square or alternatively hexagon head setscrews. Can be used with type SW Swivel Unit (see page 57) when connecting to inclined sections. Torque (4:1 Factor Clamping Set- Set- Lock- Product Code Hole Ø Thread of Safety) Thickness screw screw nut Dimensions Clear Tapped Tensile W N T U Width V mm kn mm Nm Nm mm mm mm mm FL106D FL106T 7 M6 1.1 3-17 M8 8 11 36 35 20 19 FL108D FL108T 9 M8 1.1 3-17 M8 8 11 36 35 20 19 FL210D FL210T 11 M10 2.4 3-19 M10 8 22 45 40 22 22 FL312D FL312T 13 M12 3.1 3-23 M10 8 22 50 46 28 25 FL412D FL410T 13 M10 3.1 3-28 M10 8 22 53 51 27 26 Order example: FL210D with Hex Setscrew FL210D with Square Head Setscrew and SW10 Installation 1. Slide FL onto beam flange and tighten setscrew to recommended torque. Guideline: tighten the setscrew finger tight and then apply a further quarter turn (90 ) with spanner. 2. Tighten the locknut (N) to the recommended torque. On tapered flanges the cup point setscrew has to grip on the inside of the flange. 56
4 Malleable iron, bright zinc plated Setscrew Locknut Main Body T N V W U Beam clamp with tapped holes in position and to accept threaded rod or cable clips. For parallel or tapered flanges. Supplied with grade 8.8 cup point setscrew. Installation see page 56 type FL Torque Product Thread (4:1 Factor of Safety) Clamping Thickness Setscrew Setscrew Locknut Dimensions Code Tensile / in Pos. Tensile / in Pos. W N T U Width V kn kn mm Nm Nm mm mm mm LC06 M6 M6 0.18 0.59 3-20 M6 4 4 25 36 21 LC08 M8 M8 0.18 0.59 3-20 M6 4 4 25 36 21 Order example: LC06 High Grade Alloy Steel, bright zinc plated Type FL Type 10 U R V Swivel unit for applications on inclined beams. Can be used with type FL or type 10. Supplied complete with grade 8.8 M10 x 90 setscrew and nut. Dimensions Product (4:1 Factor of Safety) Max. With Bolt Code Rod Tensile Inclination Rotation Torque U R Width V kn Nm mm mm mm SW10 M10 2.4 18 360 11 45 25 35 Order example: SW10 57
4 Malleable iron, hot dip galvanised Nut Single Leg Bolt Double Leg T V R S W V A two part flange clamp with large clamping range.the bolt can be substituted with either drop rod or J bolts. For parallel flanges only. Product Code Clamping with without Bolt 4.6 (4:1 Factor of Safety) Thickness Dimensions Bolt Bolt Tensile W Torque S T V Width R kn mm Nm mm mm mm mm mm F308NC F308NB M8 0.9 0-25 6 19 6 8 20 33 F310NC F310NB M10 1.2 0-30 20 22 7 10 25 38 F312NC F312NB M12 2.0 0-40 39 29 9 12 35 49 F316NC F316NB M16 4.0 0-55 93 36 12 16 46 60 F320NC F320NB M20 6.0 0-70 177 44 15 19 55 76 Order example: F308NC Malleable iron, hot dip galvanised T S V 1 W V 2 A two part flange clamp which fixes claw type cable cleats directly beneath the flange. Supplied with grade 4.6 bolt. Clamping Product Bolt 4.6 (4:1 Factor of Safety) Thickness Thread Dimensions Code Tensile W Torque T V 1 V 2 Width S kn mm Nm mm mm mm mm mm F310BICCA M10 1.2 0-30 M10 20 6.5 10 16 30 40 Order example: F310BICCA 58
4 Pre-galvanised strip Hanger Nut A With special nut C B With standard nut The strap hanger carries FM approval for use in fire sprinkler installations. Supplied with or without a hanger nut. Product Code with without Pipe Nuts Hole Ø Dimensions Nut Nut Bore Tapped A B C mm mm mm mm SH025N SH025 25 M8 or M10 11 22 75 58 SH032N SH032 32 M8 or M10 11 22 86 64 SH040N SH040 40 M8 or M10 11 22 99 74 SH050N SH050 50 M8 or M10 11 22 116 85 SH065N SH065 65 M8 or M10 11 22 135 97 Product Code with without Pipe Nuts Hole Ø Dimensions Nut Nut Bore Tapped A B C mm mm mm mm SH080N SH080 80 M8 or M10 11 22 159 114 SH100N SH100 100 M8 or M10 11 22 219 161 SH125N SH125 125 M12 13 27 247 177 SH150N SH150 150 M12 13 27 284 200 SH200N SH200 200 M16 18 24 373 261 Order example: SH025N with M10 hanger nut Malleable iron, bright zinc plated / hot dip galvanised Hemispherical Washer R W2 W1 L 10 Hemispherical Cup For vertical suspension on angled surface of up to 10 swing either side of the vertical. The hemispherical washer (HW) can be used without the cup. Loads are subject to applications, please contact Lindapter. Dimensions Product Code Hemispherical Washer Hemispherical Cup Hemispherical Washer & Cup Hemispherical Washer Hemispherical Cup W 1 W 2 R L mm mm mm mm mm mm HW06-19 9 - - - - HW08-22 10 - - - - HW10 HC10 25 12 32 12 13 14 HW12 HC12 29 12 35 12 14 16 HW16 HC16 34 16 41 16 17 19 HW20 HC20 44 19 54 19 22 24 HW24 HC24 57 25 67 25 29 32 Order example: HC10 BP 59
4 Mild steel - bright zinc plated A purlin clip to suit a large range of purlin sections. Can be used with type SW Swivel Unit (see page 57) for use on inclined purlins. Product (3:1 Factor of Safety) Code Purlins Rod Tensile Torque kn Nm 10 Kingspan M10 0.2 8 Multibeam 2 & 3 10 Metsec M10 0.1-0.2 8 10 eta M10 0.15 8 Order example: 10 10 with SW10 Pre-galvanised strip Installation 1. 2. 3. The purlin clip HCW30 is suitable for horizontal purlins. Can be used with type SW-Swivel Unit (see page 57) for use on inclined purlins. Installation Product (3:1 Factor of Safety) Code Purlins Rod Tensile Torque kn Nm HCW30 Kingspan M10 0.2 8 Multibeam 3 Order example: HCW30 1. 2. 60
4 Pre-galvanised strip A universal purlin clip suitable for multiple different applications. Product (3:1 Factor of Safety) Code Purlin Tensile kn HCW31 Kingspan Multibeam 3 0.2 Order example: HCW31 Mild Steel, bright zinc plated The Webfix WF for a quick installation directly from the web of ed purlins. Max. Distance Product (5:1 Factor of Safety) Max. Hole at Angle of Code Rod Tensile Purlin Thickness Ø 10º 20º 30º kn mm mm mm mm mm WF10 M10 1.0 4 18 103 94 74 Order example: WF10 Installation Squeeze legs of WF together and push through hole until it snaps into place. 1. 2. Assemble with nut and ensure full thread capture. Hole position for angled purlins Canted Purlins: As the angle of backwards cant increases, the maximum allowable distance (hole centre to bottom edge of purlin) must 1. decrease. 2. Inclined Purlin: The WF adjusts to whatever angle is required. Hole position is not a limiting factor on product installation. 61
4 Pre-galvanised strip A one-piece wrap around purlin hanger. The HCW34 can be used to suspend from canted purlins at up to 15 from the vertical. H Purlin Kingspan Multibeam 3 (3:1 Factor of Safety) Product Code Purlin Height Total Height H Rod Tensile mm mm kn HCW34/145 145 210 M10 0.75 HCW34/175 175 240 M10 0.75 HCW34/205 205 270 M10 0.75 HCW34/235 235 300 M10 0.75 HCW34/265 265 330 M10 0.75 Order example: HCW34/145 Multichannel Lipped C Section Swagebeam Multibeam ed Section SFS C Section UltraBEAM eta Section Ultrazed Section 62
4 Type F3 Type WF Type FLS 1 2 3 Type HCW31 Type HCW30 Type 10 Type SH Type SH 4 63