. Bref descrpton 44 The HR9 radator controller s certfed by eu.bac.. Scope of delvery The radator controller packagng contans: Radator controller wth valve baseplate M x.5; batteres ncluded Dsplay support Valve adapter type Danfoss RA 4 Screws for securng radator controller and battery compartment WARNING TheraPro HR9 Electronc Radator Controller Danger of suffocaton! ffkeep packagng materals away from chldren. 4 Wth the electronc radator controller, you can set your room temperature exactly to your requrements whle addtonally savng energy. Please note: The HR9 radator controller does not drectly swtch your boler on/off. It provdes local room temperature control whlst the boler s runnng. The boler wll be swtched on/off by other controls such as tmer, thermostat, etc. User-frendly Large, adjustable dsplay wth backlght. Convenent programmng by removng the radator controller from the valve. Copy functon for transferrng the tme program to other HR9 radator controllers. Installaton The radator controller fts on the most common radator valves of the type M x.5. After mountng the radator controller operates mmedately to the factory set program. Features for your convenence Indvdual programs for each day of the week. Up to 6 setponts per day and dfferent temperatures. Holday, party and specal day operatng modes can be set easly. Parameters can be set ndvdually, see Secton 9. Operaton lock/chld-proofng to protect aganst unauthorzed operaton. Optonal connecton to external sensors and wndow poston contact Energy savng features Wth the wndow functon, the radator valve s closed when ventlatng the room. In ECO mode, the room temperature s lowered by C. Optmzed control of the room temperature. CAUTION Care of use s requred! ffuse the radator controller only n accordance wth these operatng nstructons. ffdo not let chldren play wth the radator controller.
. Devce overvew Operatng elements and dsplay 9 8 AUTO ECO MANU PROG Heatng perod/setback perod n hours Day of the week 7 (Monday Sunday). Dsplayed only whle the tme program s beng programmed Temperature dsplay: e.g. set pont temperature (factory settng) or measured temperature, f confgured n Parameter 9 4 Text dsplay wth 9 characters 5 Button : Confrm settngs 6 Button PROG: Select the operatng modes, set the tme program; Press button > seconds): access to the parameter menu; Programmng: Back to next level up 7 Adjustment dal: Change the set pont, navgate menu 8 Button AUTO/ECO/MANU: Change between automatc, ECO and manual mode In programmng mode: Ext (wthout storng) 9 Battery status Operaton lock Symbol for Comfort temperature, Comfort temperature, Setback temperature Battery dsplay Battery status Meanng Batteres fully charged Batteres half charged 4 5 6 Batteres have to be replaced soon 7 4. Installaton Ready to operate n three steps: Insert batteres Set the language, tme and date Mount on radator FINISHED Insertng/changng batteres The radator controller s set for the followng battery type: alkalne cells.5 V; type LR6, AA, AM You can nstead use the followng batteres or rechargeable batteres: Lthum.5 V; type LR6, AA, AM NMH. V; type LR6, AA, AM. If lthum or NMH batteres are used, Parameter 4 has to be adapted, see Secton 9. Always change batteres n pars. 5... 4. 6. 7. + Flashng dsplay: Batteres are dead and have to be replaced
. Pull off the adjustment dal. To do so, start at the notch on the bottom of the devce.. If used, unscrew any fastenng screws from the battery compartment.. Release the lock and fold out battery sprng. The battery compartment s now accessble. 4. Insert the batteres. Ensure that the polarty + and s correct. 5. Fold down the battery sprng and latch t n. 6. Opton: Screw the battery sprng to secure the batteres aganst removal. 7. Place the adjustment dal back on. Frst the software verson number and then the language deutsch (German) s dsplayed. 8. If desred, use the adjustment dal to select a dfferent language. 9. Confrm the selected language wth the button. hour s dsplayed. WARNING The language selecton s only dsplayed durng ntal commssonng. Durng future battery changes, settng of tme and date s prompted drectly. The battery lfe of new alkalne cells amounts to approx. years. The batteres need changng when the symbol flashes. All settngs are retaned when the batteres are changed. Exploson hazard! ffnever charge non rechargeable batteres. ffnever short-crcut batteres or throw them nto fre. ffdspose of used batteres ecologcally. Settng the tme and date. When hour s dsplayed, use the adjustment dal to set the current hour and confrm wth. mnute s dsplayed.. Use the adjustment dal to set the current mnute and confrm wth. year s dsplayed.. Use the adjustment dal to set the current year and confrm wth. month s dsplayed. 4. Use the adjustment dal to set the current month and confrm wth. day s dsplayed. 5. Use the adjustment dal to set the current day and confrm wth. The normal dsplay wth set temperature and selected operatng mode s dsplayed. Checkng/changng the tme and date Proceed as follows to check or to change the date and tme later on:. Press the PROG button.. Select tme date and confrm wth. hour s dsplayed.. Further checkng/changng s carred out as descrbed above. Mountng the radator controller The radator controller can be mounted on all common thermostatc valves wth an M x.5 connecton wthout dranng system. WARNING Prevent damage to the radator controller through humdty and mosture! ffmount the radator controller n dry, closed rooms only. ffprotect the radator controller aganst humdty, mosture, dust, drect sunlght or exposure to excessve heat. Removng the old thermostat head.. Turn the old thermostat head counter-clockwse untl t stops and loosen the mountng rng.. Remove the old thermostat head from the radator valve..
Selectng the adapter The radator controller fts on common radator valves of the type M x.5. Adapters are requred for some valve types.. Check whether an adapter s requred and, f necessary, select the approprate adapter. Brand Illustraton Adapter Honeywell- Braukmann, MNG, Hemeer, Oventrop valves M x.5 Danfoss RA Not requred Suppled... Turn the adjustment dal of the valve baseplate antclockwse untl t stops.. Put the valve baseplate onto the radator valve or the adapter and tghten by hand (wthout tools!). Mountng the radator controller.. Danfoss RAV. Danfoss RAVL. Slde the adapter onto the radator valve and turn t untl you feel t clck nto place.. If necessary, screw the adapter tght wth a screw. Mountng the valve baseplate. Ensure that the slde on the radator controller s n the open poston.. Put the radator controller onto the valve baseplate so that the ndentaton latches n and s no longer vsble.. Lock the radator controller n the end poston. To do so, push the slde towards. After approx. mnute cycl (self-test) s dsplayed. Afterwards the radator controller changes to automatc mode. a b. Separate the valve baseplate from the radator controller. To do so, push the slde towards. The radator controller only operates f t s locked correctly n the end poston. FINISHED! After mountng, the radator controller operates mmedately n the factory settng (standard tme program), see Secton 5. 4
Securng the radator controller The radator controller and the batteres can be secured aganst removal by usng the suppled screws. Settng the poston of the dsplay In order to mprove the legblty the dsplay of the radator controller can be tlted to dfferent postons (,,, 4 ). The angle of 4 can be fxed wth the suppled dsplay support... Mountng. Lft the dsplay and set t to the desred angle.. If desred, tlt the dsplay by 4 and slde the dsplay support from above between the dsplay and the housng untl t latches n. Unmountng fpress f the dsplay support n at the back and remove t upwards. Connectng optonal sensors and wndow contact The followng external sensors and wndow contacts can be connected to the HR9 radator controller: HCW setpont adjuster RF room sensor HCA floatng wndow contact The ACS9 cable s requred to connect external sensors and the wndow contact. Mcro B mn-plug / open ends m long Not ncluded n the scope of delvery Operaton wth HCW setpont adjuster The room temperature s measured by the HCW setpont adjuster. The HR9 nternal room temperature sensor s not used n ths partcular applcaton. The adjustment dal of the HCW can be used to change the room temperature ± K as an offset to the temperature set/programmed at the HR9. The offset settng remans vald untl t s changed agan. Operaton wth RF room sensor The room temperature s measured by the external RF room sensor. The HR9 nternal room temperature sensor s not used n ths partcular applcaton. Operaton wth wndow contact When the wndow s opened, the wndow contact s opened and the radator valve closes. When the wndow s closed agan, the radator controller returns to normal operaton. The frost-protecton functon ensures that the radator valve opens when the temperature drops below 5 C. When de-nstallng a connected room sensor RF or room unt HCW, remove the batteres and nsert them agan to avod error messages. When de-nstallng the wndow contact, change parameter 7 to or, see secton 9. 5
Cable connecton For further nformaton also refer to the documentaton for HCW, RF and HCA. fconnect f the ACS9 cable as follows to the external sensor and wndow contact: HCW setpont adjuster ACS9 RF room sensor ACS9 whte NTC green TW/F black GND whte NTC black GND green TW/F HCW RF room sensor and floatng HCA wndow contact ACS9 whte NTC black GND green TW/F HCA floatng wndow contact ACS9 whte NTC black GND green TW/F Connectng the cable wth the HR9 radator controller.. ϑ ϑ 5. Operaton Standard tme program (factory settng) In automatc mode, the radator controller automatcally controls the room temperature n accordance wth the stored tme program. Week program : At home all day Factory preset tme program s set for each day of the week Mo Su ( 7): C 6 C Lowerng/ Savng Heatng Setpont Tme Temperature Setpont Setpont 6: : C (Comfort temperature ) : 6: 6 C (Setback temperature) Two further week programs are stored n the radator controller. Further nformaton s avalable n Secton 9. You can also adapt one of the stored week programs to your ndvdual requrements, see Secton 8. Adaptng the temperature temporarly If you want to change the temperature specfed by the tme program temporarly: fset f your desred temperature usng the adjustment dal. The change remans n effect untl the next setpont. The process of changng the temperatures permanently s descrbed n Secton 7.. Remove the sde cover from the radator controller.. Insert the cable ACS9 nto the HR9 radator controller. The radator controller recognzes the connected sensor / wndow contact automatcally. 6
Savng energy n ECO mode In ECO mode, the room temperature n automatc mode specfed by the tme program s lowered by C. fto f actvate ECO mode, press the button AUTO/ ECO/MANU untl economy s dsplayed. The dsplayed temperature s reduced by C. ECO mode runs untl you press the button AUTO/ ECO/MANU agan and select a dfferent operatng mode. Manual mode In manual mode, the radator controller operates at the (manually) set temperature untl you change the temperature or change to a dfferent operatng mode. fto f actvate the manual mode. press the button AUTO/ECO/MANU untl manual s dsplayed. The temperature can be adjusted manually usng the adjustment dal. Manual mode runs untl you press the button AUTO/ ECO/MANU agan and select a dfferent operatng mode. 6. Programmng Operatng modes Overvew of the operatng modes "Party" operatng mode: In ths operatng mode, you can specfy a temperature for a number of hours. After the set perod has expred, the radator controller changes back to automatc mode. "Day off" operatng mode: If, for example, a publc holday durng the week, the automatc mode settngs may not meet your requrements on these days. In such cases you can actvate a dfferent tme program for one or more days. After the set perod has expred, the radator controller changes back to automatc mode. "Holday" operatng mode: In ths operatng mode you can specfy a temperature for a specfc number of days. After the set perod has expred, the radator controller changes back to automatc mode. Selectng operatng modes Selectng the "Party" or "Holday" operatng mode. Press the PROG button and turn the adjustment dal to the left untl party or holday s dsplayed.. Confrm the selected operatng mode wth the button. Hours or Days flashes.. Use the adjustment dal to set the desred number of hours or days and confrm wth. The temperature dsplay flashes. 4. Use the adjustment dal to set the desred temperature and confrm wth. The selected operatng mode and the set temperature are dsplayed. Selectng the "Day off" operatng mode. Press the PROG button and turn the adjustment dal to the left untl day off s dsplayed.. Confrm the selected operatng mode wth the button. days flashes.. Use the adjustment dal to set the desred number of days and confrm wth. The selected operatng mode s dsplayed. The procedure of creatng the tme program for specal days s descrbed n Secton 8. When you enter the number of days for holdays/ specal day the current day counts as the frst day. An overvew of the program structure s shown on the last page of these nstructons. 7
7. Programmng Temperatures Three preset temperatures can be assgned to the set ponts n the tme program: Comfort temperature Factory settng C Comfort temperature Factory settng C Setback temperature Factory settng 6 C Settng the temperatures. Press the PROG button. comfort s dsplayed.. Press the button, use the adjustment dal to set the Comfort temperature and confrm wth. saved s dsplayed brefly and then agan comfort.. Turn the adjustment dal clockwse untl the next temperature s dsplayed. 4. Repeat Steps and for the Comfort temperature and the Setback temperature. 5. Use the AUTO button to ext programmng. The three preset temperatures (Comfort temperature, and Setback temperature) can be changed at any tme. Durng programmng the PROG button can be used to return to the next level up. You can abort programmng at any tme by usng the AUTO button. An overvew of the program structure s shown on the last page of these nstructons. Operatng hnts Operatng the radator controller comfortably The radator controller can be removed from the radator to facltate programmng.... Unlock the radator controller. To do so, push the slde at the radator controller towards.. Pull the radator controller off the valve baseplate. Lost your way n the program? fpress f the button AUTO/ECO/MANU automatc s dsplayed. The last entry s rejected. 8. Programmng Tme program Plannng the tme program You can specfy up to 6 setponts per day. The followng has to be assgned to each setpont: One of the three preset temperatures (Comfort temperature, and Setback temperature). Begnnng of the Heatng/Setback perod End of the Heatng/Setback perod Example Comfort Comfort Savng Lowerng/ Savng Heatng Heatng Heatng Setponts 4 5 6 8
The example shows the followng tme program: Setpont Tme Temperature 6: 9: C (Comfort temperature ) 9: : 6 C (Setback temperature) : 4: C (Comfort temperature ) 4 4: 7: 6 C (Setback temperature) 5 7: : C (Comfort temperature ) 6 : 6: 6 C (Setback temperature) An overvew of the program structure s shown on the last page of these nstructons. Week program You can adjust the tme program to your personal weekly routne. You have the followng optons to ths purpose: Separate tme programs for weekdays Mo Fr ( 5) and weekend Sa Su (6 7) One tme program for the days of the week Mo Su ( 7) A dfferent tme program for each day of the week Mo, Tu, We, Th, Fr, Sa, Su (,,, 4, 5, 6, 7) We recommend that you wrte down your tme program before begnnng programmng. Settng the tme program Selectng weekdays. Press the PROG button. comfort s dsplayed.. Turn the adjustment dal clockwse untl program s dsplayed.. Press the button and use the adjustment dal to select the desred weekdays for your tme program: mo - fr, sa - su, mo - su, mo, tu,, su or day off 4. Confrm the selected weekdays wth the button. The temperature as well as the begnnng and end of the frst setpont, e.g.: The end of a setpont s also the begnnng of the next setpont. You can use the adjustment dal to change from one setpont to another and thus vew the settng of all the programmed setponts. Only the programmed setponts are dsplayed. Edtng setponts. In order to edt the dsplayed setpont press the button. The temperature dsplay flashes.. Use the adjustment dal to select the desred temperature (Comfort temperature, or Setback temperature) for the selected setpont and confrm wth. The begnnng of the selected setpont flashes. The tme scale for programmng of the setponts begns at : n the mornng and ends at :5 on the followng day.. Use the adjustment dal to set the desred begnnng for the selected setpont and confrm wth. The end of the selected setpont flashes. 4. Use the adjustment dal to set the desred end of the selected setpont and confrm wth. saved s dsplayed brefly. Subsequently the temperature as well as the begnnng and end of the setpont are dsplayed. 5. For the further setponts also select the temperature as well as the begnnng and end of the setpont as descrbed n Steps to 5. A setpont s not saved untl the temperature, begnnng and end have been confrmed wth the button. If a setpont s not requred, select the settng --.-. Edtng further weekdays. When all the setponts have been edted, use the PROG button to select the weekdays.. Edt the setponts for the next weekdays.. After all the requred weekdays have been set, ext programmng wth the AUTO button. The radator controller operates mmedately n automatc mode wth the set tme program. 9
Deletng a setpont fwhen f a setpont s not requred, select the temperature settng --.- and confrm wth. The frst setpont cannot be deleted. Addng a setpont. Turn the adjustment dal untl add new s dsplayed and confrm wth. The temperature dsplay flashes.. Use the adjustment dal to select the desred temperature (Comfort temperature, or Setback temperature) for the new setpont and confrm wth. The begnnng of the new setpont flashes.. Use the adjustment dal to set the desred begnnng for the new setpont and confrm wth. The end of the desred setpont flashes. 4. Use the adjustment dal to set the desred end of the new setpont and confrm wth. add new s only dsplayed when less than 6 setponts are programmed. Copyng the tme program If several HR9 radator controllers are to operate wth the same tme program, the tme program only has to be created at one devce (master) and can then be coped to further radator controllers. The ACC9 cable s requred to copy the tme program. x Mcro B mn-plugs.5 m long Not ncluded n the scope of delvery. Remove the sde cover from all the radator controllers.. Connect the master (wth tme program) and a further HR9 radator controller usng the ACC9 cable.. Press the buttons AUTO and at both devces smultaneously for 4 seconds. com mode s dsplayed n the dsplay of both devces. 4. Press the PROG button at the master. master s dsplayed on the master and then trams,mt. com mode s dsplayed on the other devce and then receve. The tme program s coped. 5. The copyng process s completed when fnshed s dsplayed at both devces. 6. After seconds the devce wth the coped tme program changes to the automatc mode, com mode s dsplayed agan at the master. 7. Dsconnect the ACC9 cable from the devce wth the coped tme program. If there are no actvtes at one of the two radator controllers for 4 mnutes, they change automatcally to automatc mode. Copyng to further devces. Insert the ACC9 cable nto the next devce.. Press the buttons AUTO and at the next devce smultaneously for 4 seconds. com mode s dsplayed at ths devce. com mode s dsplayed at the master.. Press the PROG button at the master. The further copyng procedure s the same as descrbed at the frst copyng process. Termnatng copyng After the last copyng process has been completed:. Press the AUTO button at the master n order to change to the automatc mode.. Remove the ACC9 cable and put the sde cover back on at all the devces....
9. Controller operatng parameters Overvew If requred, the 9 basc settngs (parameters) can be adjusted. Factory settngs have a grey background. Parameters marked wth an * are descrbed n more detal below. Par. Settng Meanng 4 5 6 7 8 9 4 5 6 9.... Language settng German Englsh Dansh Swedsh Norwegan Fnnsh Preset tme programs * Week program "At home all day" Week program "Lunch break at home" Week program "Part-tme work" Backlght * Deactvated Actvated Summer/wnter tme changeover No automatc changeover Automatc changeover Duraton of the wndow functon * Wndow functon not actve Valve opens at the latest after mnutes Valve opens at the latest after 9 mnutes Senstvty of the wndow functon durng droppng room temperature *. (senstve). (less senstve) Factory settng:.4 Senstvty of the wndow functon durng rsng room temperature *. (senstve). (less senstve) Factory settng:. Settng the valve stroke * Standard valve stroke Full-stroke mode Temperature representaton n the dsplay * Set/programmed temperature (setpont temperature) Measured room temperature Par. Settng Meanng 4 5 6 7 8 9 6 7 5 6 5-4 5 6 7 Upper temperature lmt The room temperature cannot be set hgher than the specfed upper temperature lmt (Max Lmt). Factory settng: C Lower temperature lmt The room temperature cannot be set lower than the specfed lower temperature lmt (Mn Lmt). Factory settng: 5 C Optmzaton functon * No optmzaton Optmum start Optmum start/stop Temperature offset * To adjust the temperatures measured by the radator controller and n the room Factory settng: C Battery type Alkalne Lthum NMH (rechargeable batteres) Dsplay valve poston * No dsplay of the valve poston Momentary dsplay of the valve poston Valve exercse day * Monday Tuesday Wednesday Thursday Frday Saturday Sunday Off Wndow open functon * Off (no wndow functon) Auto (correspondng to Parameters 5-7) Cabled (wth floatng wndow contact) Temperature unt Celsus Fahrenhet Restore to factory settng No reset Reset only the basc settngs Reset only the tme program Reset all
Changng parameters. Keep the PROG button pressed for at least seconds untl Parameter flashes (left-hand dgt). Setpont Tme Temperature 6: 9: C (Comfort temperature ) 9: : 6 C (Setback temperature) : : C (Comfort temperature ) 4 : 7: 6 C (Setback temperature) The rght-hand dgt shows the current settng. The parameter s dsplayed addtonally n plan text. For example, the dsplay stands for Parameter (language) wth Settng (German).. Use the adjustment dal to select the desred parameter (left-hand dgt).. Press the button to edt the parameter. The current settng of the parameter flashes (rght hand dgt). 4. Use the adjustment dal to set the desred settng (rght-hand dgt) and confrm wth. The parameter beng edted flashes (left-hand dgt). 5. For the further parameters repeat Steps to 4. 6. Use the AUTO button to return to automatc mode. Descrpton of the parameters Parameter Selectng the preset tme programs Week program (factory settng, setponts): Mo Su ( 7) at home all day Ths tme program s descrbed n Secton 8. Week program (6 setponts): Mo Fr ( 5) lunch break at home Sa Su (6 7) lke Week program C 5 7: : C (Comfort temperature ) 6 : 6: 6 C (Setback temperature) Week program (4 setponts): Mo Fr ( 5) part-tme work Sa Su (6 7) lke Week program C C 6 C Lowerng/ Savng Setponts Heatng Setpont Tme Temperature Heatng. 6: to 9: C (Comfort temperature ). 9: to : 6 C (Setback temperature). : to : C (Comfort temperature ) 4. : to 6: 6 C (Setback temperature) Parameter Backlght The dsplay has a backlght for readng the nformaton. The backlght s ON when the adjustment dal s turned or a button s pressed. The backlght swtches OFF f no acton s carred out at the radator controller for approx. 7 seconds n order to save battery power. 4 C 6 C Lowerng/ Savng Setponts Heatng Heatng 4 5 6
Parameters 5 to 7 Wndow functon In order to save energy, the radator controller closes the radator valve when you open a wndow resultng n a large drop of the temperature. When you close the wndow so that the temperature rses the radator controller opens the radator valve agan. If you should ever forget to close the wndow, the radator controller opens automatcally after the set tme n order to ensure frost protecton. Parameter 8 Valve stroke The radator controller operates wth the optmum valve stroke set n the factory. If the entre valve stroke s to be used or f the valve does not open completely, actvate the full-stroke mode. Parameter 9 Temperature representaton n the dsplay In the factory settng the set or programmed temperature (Comfort temperature, or the Setback temperature) s dsplayed. Wth the settng "measured temperature" the measured room temperature s dsplayed. A changeover to the set temperature s carred out by turnng the adjustment dal or pressng a button. If requred, the temperature can now be reset. The dsplay returns to the measured temperature after approx. seconds. Due to the heat nfluence of the radator the "measured temperature" dsplayed at the radator controller can dffer from the temperature measured at another pont n the room. Parameter Optmzaton functon Wthout optmzaton (factory settng) the radator controller begns to heat up the room or lower the temperature at the programmed tme. For example, n order to have a warm bathroom at 7:, the setpont has to be brought forward. Otherwse the room only starts heatng at 7:. However, the advanced setpont may le too early so that heatng s started far earler than necessary. Wth optmzaton the radator controller calculates when to open the valve n order to acheve the desred temperature at the set tme. Optmum start The room s heated up at the optmum moment n order to reach the programmed temperature. Optmum start/stop: The room s heated up at the optmum moment and cooled down at an earler moment. C Optmum Start Wthout Optmzaton Setpont Optmum Stop Setpont Wthout Optmzaton Parameter Temperature offset Snce the radator controller measures the room temperature n the area of the radator, t s possble that ths temperature devates from the temperature measured at a dfferent pont n the room. If, for example, C s measured n the room and. C at the radator, ths effect can be compensated by an offset of. C. Parameter 5 Dsplay of the valve poston When ths parameter s actvated (settng ""), the calculated valve poston ( to % opened) s dsplayed momentarly. The man dsplay s shown agan after approx. mnutes or when the AUTO button s pressed. Parameter 6 Valve exercse day If the radator valve has not been opened once completely wthn the perod of weeks, a self-test (forced operaton) s carred out. The radator controller opens the radator valve brefly on the subsequent Monday (factory settng) n order to prevent sezng. The weekday for valve protecton can be selected freely Parameter 7 Wndow open functon If a wndow contact s connected, the parameter s set automatcally to "" (cabled). The wndow functon s controlled by the wndow contact. If no wndow contact st present, the parameter must be set to or.
. Further functons Montorng functons Wndow functon If you open a wndow causng the temperature to drop, the radator controller closes the radator valve n order to save energy. wndow s dsplayed. When the temperature rses agan, but at the latest after the set perod (factory settng: mnutes), the radator controller opens the radator valve agan. You can also open the radator valve beforehand by pressng the AUTO button or turnng the adjustment dal. The senstvty of the radator controller to a temperature drop or temperature rse can be set, see Secton 9, Parameters 5 to 7. If a wndow contact s connected, the wndow functon reacts drectly to the openng and closng of the wndow, see Parameter 7. Valve protecton If the radator valve has not been opened once completely wthn a perod of weeks, a self-test (forced operaton) s carred out. The radator controller opens the radator valve brefly on the subsequent Monday (factory settng) n order to prevent sezng. cycl s dsplayed. The day for the valve protecton can be set n Parameter 6. Frost protecton If the temperature drops below 5 C, the radator controller opens the radator valve untl the temperature rses above 6 C agan. Ths prevents the heatng system from freezng up. frost s dsplayed. The heatng must be swtched on to ensure the frost protecton functon. Manual overrde If you have swtched off the central heatng system n summer and do not want to waste the batteres of the radator controller, you can close the radator valve contnuously. Closng the valve. Press the button AUTO/ECO/MANU untl manual s dsplayed.. Turn the adjustment dal counter-clockwse untl off s dsplayed. The radator valve now remans closed. The valve and frost protecton functons contnue to be actve. Openng the valve fuse f the AUTO/ECO/MANU button to change to automatc mode. or fset f the desred temperature n manual operaton. Chld-proofng / Operaton lock You can block the radator controller to protect t aganst unauthorzed operaton: fkeep f the AUTO/ECO/MANU and PROG buttons pressed smultaneously for at least seconds. The symbol s dsplayed. The same key combnaton s used to release the radator controller agan for operaton. 4
. Help wth problems Error table Problem/ Dsplay e sensor e valve The radator stays hot The room does not heat up durng optmzaton Motor does not move Cause Remedy flashes Batteres flat Replace the batteres. Devce defectve Motor can not be moved. The radator valve does not close fully. Heatng s not swtched on n tme Valve baseplate not nterlocked Replace the devce. Check the nstallaton. Check the nstallaton. If approprate, change to full-stroke mode (Parameter 8). Ensure that the precontroller swtches on the heatng. Synchronze the on/ off tmes of boler control and radator controller. Set the slder to the poston. Emergency operaton when batteres are flat. Unlock the radator controller. To do so, push the slde at the radator controller towards.. Pull the radator controller off the valve baseplate.. Operate the radator valve by hand usng the adjustment dal on the valve baseplate. + Restorng the factory settng. Keep the PROG button pressed for approxmately seconds untl Parameter flashes (left-hand dgt).. Use the adjustment dal to select Parameter 9 (lefthand dgt) and Settng (rght-hand dgt).. Press the button to restore the factory settng.. Techncal data Type Protecton class Supply voltage Power consumpton HR9 IP Control accuracy (CA).5 C Connecton to the radator M x.5 Ambent temperature 5 C Transport and storage temperature Dmensons Weght Ambent condtons Humdty Standards. Dsposal Battery type LR6, AA, AM Alkalne: x.5 V Lthum: x.5 V NMH: x. V Standby: typ. 65 mw Control: typ. 4 mw C 65 C 96 x 54 x 6 mm 85 g (wth batteres) For lvng area, busness and trade sectons as well as small busnesses 9 % rel. humdty EN554-:6 +A: EN554-:997 +A:8 EN67-: EN67--9: RoHS /65/EC CE The radator controller has to be dsposed of n accordance wth WEEE drectve /9/EC Waste Electrcal and Electronc Equpment drectve. ffat the end of the product lfe dspose of the packagng and product n a correspondng recyclng centre. ffdo not dspose of the unt wth the usual domestc refuse. ffdo not burn the product. ffremove the batteres. ffdspose of the batteres accordng to the local statutory requrements and not wth the used domestc refuse. 5
4. Programmng Overvew Temperatures and operatng modes Button PROG (turn adjustment dal counter-clockwse) tme date holday day off party Hours Days Days (turn adjustment dal clockwse) comfort comfort setback program Hours Mnute Edt tme program, see below Year Month Day Tme program program (turn adjustment dal) mo - fr sa - su mo - su mo tu su day off SP SP 6 (turn adjustment dal) Begnnng End Begnnng End New setpont: End Begnnng add new Delete a setpont: SP x --:--. (Delete) Begnnng End Manufactured for and on behalf of the Envronmental and Combuston Controls Dvson of Honeywell Technologes Sàrl, ACS-ECC EMEA, Z.A. La Pèce 6, 8 Rolle, Swtzerland by ts Authorzed Representatve Honeywell Honeywell House Skmped Hll Lane Bracknell Berkshre RG EB Unted Kngdom The rght s reserved to make modfcatons that serve mprovement. 58-C www.hr9.nfo