REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/ PREPRED BY RICK OFFICER DL LND ND MRITIME 43218-3990 http://www.dla.mil/landandmaritime Original date of drawing YY-MM-DD CHECKED BY RJESH PITHDI 17-12-01 PPROVED BY CHRLES F. SFFLE TITLE MICROCIRCUIT, LINER, 0.1 GHz to 3.0 GHz, 1 db LSB, 5 BIT, Gas DIGITL STEP TTENUTOR, MONOLITHIC SILICON CODE IDENT. NO. REV PGE 1 OF 14 DISTRIBUTION STTEMENT. pproved for public release. Distribution is unlimited. MSC N/ 5962-V012-18
1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 0.1 GHz to 3.0 GHz, 1 db least significant bit (LSB), 5 bit, gallium arsenide (Gas) digital step attenuator microcircuit, with an operating temperature range of -55 C to +125 C. 1.2 Vendor Item Drawing dministrative Control Number. The manufacturer s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: 1.2.1 Device type(s). - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) Device type Generic Circuit function 01 HMC470-EP 0.1 GHz to 3.0 GHz, 1 LSB, 5 bit, Gas digital step attenuator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 16 MO-220-VEED-4 Lead frame chip scale package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator B C D E F Z Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Tin-lead alloy (BG/CG) Other DL LND ND MRITIME REV PGE 2
1.3 bsolute maximum ratings. 1/ Supply voltage (VDD)... 7 V Digital control input voltage... -1 V to VDD + 1 V RF input power 2/: (ll attenuation states, f = 250 MHz to 3 MHz, TCSE = 85 C) VDD = 3 V... 25 dbm VDD = 5 V... 27 dbm Continuous power dissipation (PD) : 3/ TCSE = 85 C... 0.5 W TCSE = 125 C... 0.19 W Junction temperature range (TJ)... 150 C Storage temperature range (TSTG)... -65 C to +150 C Reflow 4/ (moisture sensitivity level 3 (MSL3) rating)... 260 C Thermal resistance, junction to case ( JC)... 130 C/W 5/ 6/ Thermal resistance, junction to ambient ( J)... 297 C/W 5/ Electrostatic discharge (ESD) rating: Human body model (HDM)... 250 V (class 1) 1.4 Recommended operating conditions. 7/ Supply voltage range (VDD)... 3 V to 5 V Operating case temperature range (TC)... -55 C to +125 C 1/ Stresses beyond those listed under absolute maximum rating may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ For power derating at frequencies less than 250 MHz, see figure 3. 3/ See figure 4. 4/ See the ordering guide in the manufacturer s datasheet for more information. 5/ Thermal impedance simulated values are based on a JEDEC 2S2P thermal test board with five thermal vias. See JEDEC JESD-51. 6/ The device is set to maximum attenuation state. 7/ Use of this product beyond the manufacturers design rules or stated parameters is done at the user s risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. DL LND ND MRITIME REV PGE 3
2. PPLICBLE DOCUMENTS JEDEC Solid State Technology ssociation JEDEC JESD51 Methodology for the Thermal Measurement of Component Packages (Single Semiconductor Device) JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (pplications for copies should be addressed to the Electronic Industries lliance, 2500 Wilson Boulevard, rlington, V 22201-3834 or online at https://www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer s part number as shown in 6.3 herein and as follows:. Manufacturer s name, CGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer s part number and with items and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Truth table. The truth table shall be as shown in figure 3. 3.5.4 Power derating at frequencies less than 250 MHz graph. The power derating at frequencies less than 250 MHz graph shall be as shown in figure 4. 3.5.5 Maximum power dissipation versus case temperature graph. The maximum power dissipation versus case temperature graph shall be as shown in figure 5. 3.5.6 Digital control input interface circuit. The digital control input interface circuit shall be as shown in figure 6. 3.5.7 RF1, RF2 interface circuit. The RF1, RF2 interface circuit shall be as shown in figure 7. 3.5.8 Input P0.1 db versus frequency at minimum attenuation state for various temperatures graph with supply voltage at 5 V. The input P0.1 db versus frequency at minimum attenuation state for various temperatures graph with supply voltage at 5 V shall be as shown in figure 8. 3.5.9 Input P0.1 db versus frequency at minimum attenuation state for various temperatures graph with supply voltage at 3 V. The input P0.1 db versus frequency at minimum attenuation state for various temperatures graph with supply voltage at 3 V shall be as shown in figure 9. DL LND ND MRITIME REV PGE 4
TBLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/ Temperature, T Device type Limits Min Max Unit Frequency range 25 C 01 0.1 3.0 GHz Insertion loss 0.1 GHz to 1.5 GHz 25 C 01 1.3 typical db 1.6 1.5 GHz to 2.3 GHz 1.5 typical 1.8 2.3 GHz to 3.0 GHz 1.7 typical 2.0 ttenuation control range ttenuation step size ttenuation step error Between minimum and maximum attenuation states, 0.1 GHz to 3.0 GHz Between any successive attenuation states, 0.1 GHz to 3.0 GHz Between any successive attenuation states, 0.1 GHz to 33 GHz 25 C 01 31 typical db 25 C 01 1 typical db 25 C 01 0.2 typical db ttenuation state error Referenced to insertion loss state, all attenuation states, 0.1 GHz to 2.3 GHz 25 C 01 -(0.3 + 2% of attenuation state) +(0.3 + 2% of attenuation state) db Referenced to insertion loss state, 1 db to 15 db attenuation states, 2.3 GHz to 3.0 GHz -(0.3 + 3% of attenuation state) +(0.3 + 3% of attenuation state) Referenced to insertion loss state, 16 db to 31 db attenuation states, 2.3 GHz to 3.0 GHz -(0.3 + 6% of attenuation state) +(0.3 + 6% of attenuation state) Return loss Relative phase RF1 and RF2 pins, all attenuation states, 0.1 GHz to 3.0 GHz Between minimum and maximum states, 0.1 GHz to 1.5 GHz Between minimum and maximum states, 1.5 GHz to 3.0 GHz 25 C 01 14 typical db 25 C 01 12 typical Degrees 27 typical See footnotes at end of table. DL LND ND MRITIME REV PGE 5
TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/ Temperature, T Device type Limits Unit Min Max Switching characteristics. Between all attenuation states. Rise and fall time On and off time trise, tfll ton, toff 10% to 90% of RF output 25 C 01 50 typical ns 50% VCTL to 90% of RF output 25 C 01 70 typical ns Input linearity, 3/ 0.1 db compression P0.1dB ll attenuation states, 250 MHz to 3.0 GHz, VDD = 3 V 25 C 01 25 typical dbm ll attenuation states, 27 typical 250 MHz to 3.0 GHz, VDD = 5 V Input linearity, 3/ third order intercept IP3 10 dbm per tone, 1 MHz spacing 25 C 01 50 typical dbm Supply current IDD 25 C 01 1.7 typical m Digital control inputs. V1 to V5 pins Low voltage VINL 25 C 01 0 0.8 V High voltage VINH 25 C 01 2.0 VDD V Low current IINL 25 C 01 1 typical High current IINH 25 C 01 40 typical 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, VDD = 3 V to 5 V, V1 to V5 control pins voltage (VCTL) = 0 V or VDD, TCSE = 25 C, 50 system. 3/ Input linearity performance degrades at frequencies less than 250 MHz; see figure 8 and figure 9. DL LND ND MRITIME REV PGE 6
Case X FIGURE 1. Case outline. DL LND ND MRITIME REV PGE 7
Case X - continued Dimensions Symbol Inches Millimeters Minimum Nominal Maximum Minimum Nominal Maximum.0314.0334.0354 0.80 0.85 0.90 1.0031 COPLNRITY.0007.0019 0.08 COPLNRITY 0.02 0.05 2.0079 REF 0.203 REF b.0078.0098.0118 0.20 0.25 0.30 D/E.1141.1181.1220 2.90 3.00 3.10 D1/E1.0629.0669.0708 1.60 1.70 1.80 e.0196 BSC 0.50 BSC L.0137.0157.0177 0.35 0.40 0.45 S.0078 --- --- 0.20 --- --- NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. For proper connection of the exposed pad, refer to the pin configuration and function descriptions section of the manufacturer s datasheet. 3. Falls within reference to JEDEC MO-220-VEED-4. FIGURE 1. Case outline - Continued. DL LND ND MRITIME REV PGE 8
Device type 01 Case outline Terminal number Terminal symbol X Description 1 VDD Power supply. See figure 6 for the interface schematic. 2 RF1 RF input or output of the attenuator. The RF1 pin is dc coupled to VDD and ac matched to 50. n external dc blocking capacitor is required. Select the capacitor value for the lowest frequency of operation. See figure 7 for the interface schematic. 3 NIC Not internally connected. These pins are not internally connected; however, all data shown herein was measured when these pins were connected to the RF/dc ground of the evaluation board. 4 CG1 C grounding capacitor pins. Leave these pins not connected when 5 CG2 operating above 700 MHz. For frequencies less than 700 MHz, connect capacitors larger than 100 pf as close to the CGx pins as 6 CG3 possible. 7 CG4 8 CG5 9 CG6 10 NIC Not internally connected. These pins are not internally connected; however, all data shown herein was measured when these pins were connected to the RF/dc ground of the evaluation board. 11 RF2 RF input or output of the attenuator. The RF2 pin is dc coupled to VDD and ac matched to 50. n external dc blocking capacitor is required. Select the capacitor value for the lowest frequency of operation. See figure 7 for the interface schematic. 12 V1 Parallel control voltage inputs. These pins select the required 13 V2 attenuation see figure 3. See figure 6 for the interface schematic. 14 V3 15 V4 16 V5 EPD Exposed pad. The exposed pad must be connected to ground for proper operation. FIGURE 2. Terminal connections. DL LND ND MRITIME REV PGE 9
Digital control input SEE NOTE 1 ttenuation state (db) V1 V2 V3 V4 V5 High High High High High 0 (reference) High High High High Low 1 High High High Low High 2 High High Low High High 4 High Low High High High 8 Low High High High High 16 Low Low Low Low Low 31 SEE NOTE 2 NOTES: 1. ny combination of the control input states shown in figure 3 provides an attenuation equal to the sum of the bits selected. 2. 31 represents the sum total of all low logic states of the attenuator. 1 + 2 + 4 + 8 + 16 = 31 FIGURE 3. Truth table. FIGURE 4. Power derating at frequencies less than 250 MHz. DL LND ND MRITIME REV PGE 10
FIGURE 5. Maximum power dissipation versus case temperature graph. FIGURE 6. Digital control input interface circuit. DL LND ND MRITIME REV PGE 11
FIGURE 7. RF1, RF2 interface schematic. FIGURE 8. Input P0.1 db versus frequency at minimum attenuation state for various temperatures graph with supply voltage at 5 V. DL LND ND MRITIME REV PGE 12
FIGURE 9. Input P0.1 db versus frequency at minimum attenuation state for various temperatures graph with supply voltage at 3 V. DL LND ND MRITIME REV PGE 13
4. VERIFICTION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPRTION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DL Land and Maritime maintains an online database of all current sources of supply at https://landandmaritimeapps.dla.mil/programs/smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CGE code Mode of transportation and quantity Top side marking Vendor part number -01XE 24355 Reel, 50 units Y6U HMC470TCPZ-EP-PT -01XE 24355 Reel, 500 units Y6U HMC470TCPZ-EP-RL7 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CGE code Source of supply 24355 nalog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, M 02062 Point of contact: Raheen Business Park Limerick, Ireland DL LND ND MRITIME REV PGE 14