Electronically-Controlled Current-Mode Second Order Sinusoidal Oscillators Using MO-OTAs and Grounded Capacitors

Similar documents
Explicit-current-output sinusoidal oscillators employing only a single current-feedback op-amp

Third Op.amp. Abstract. 1. Introduction. Treatment. electronically. respect to the. aharashtra, India. responses, gains, tion. A S A 0.

Realization of current-mode KHN-equivalent biquad filter using ZC-CFTAs and grounded capacitors

Current differencing transconductance amplifier-based current-mode four-phase quadrature oscillator

Active-only current-mode first-order allpass filter and its application in quadrature oscillator

ELECTRONICALLY ADJUSTABLE TRIPLE-INPUT SINGLE-OUTPUT FILTER WITH VOLTAGE DIFFERENCING TRANSCONDUCTANCE AMPLIFIER

A Simple Current Mode Schmitt Trigger Circuit Based On Single CCDDCCTA without Employing Any Passive Components

Voltage-mode OTA-based active-c universal filter and its transformation into CFA-based RC-filter

VOLTAGE-MODE UNIVERSAL BIQUADRATIC FILTER USING TWO OTAs

Dual-mode Multiphase Sinusoidal Oscillator using CDBAs

CHAPTER 3 ACTIVE INDUCTANCE SIMULATION

New Simple CMOS Realization of Voltage Differencing Transconductance Amplifier and Its RF Filter Application

DESIGN OF SECOND ORDER BUTTERWORTH HIGHPASS FILTER USING CMOS TECHNOLOGY

CMOS realization of voltage differencing gain amplifier (VDGA) and its application to biquad filter

A Novel Equi-amplitude Quadrature Oscillator Based on CFOA

A CMOS Multi-Output Cross-Coupled Gain-Boosting Current- Mode Integrator

Table 1. Comparative study of the available nth order voltage mode filter. All passive elements are grounded. Number of resistors required

220 S. MAHESHWARI AND I. A. KHAN 2 DEVICE PROPOSED The already reported CDBA is characterized by the following port relationship [7]. V p V n 0, I z I

FULLY INTEGRATED MULTIFUNCTION TRANS-IMPEDANCE MODE BIQUAD FILTER

EE 435. Lecture 5 Spring Fully Differential Single-Stage Amplifier Design

EE 435. Lecture 5 Spring Fully Differential Single-Stage Amplifier Design

EE 435 Lecture 11. Current Mirror Op Amps -- Alternative perspective -- Loop phase-shift concerns. OTA circuits

EE 435 Lecture 12. OTA circuits. Cascaded Amplifiers. -- Stability Issues. -- Two-Stage Op Amp Design

Seventh-order elliptic video filter with 0.1 db pass band ripple employing CMOS CDTAs

Three Phase Inverter Simulation using Sinusoidal PWM Technique

DIGITALLY PROGRAMMABLE PARTIALLY ACTIVE-R SINUSOIDAL OSCILLATORS

CURRENT-MODE FOUR-PHASE QUADRATURE OSCILLATOR

Versatile universal electronically tunable current-mode filter using CCCIIs

Analog Integrated Circuits. Lecture 6: Noise Analysis

Differential Difference Current Conveyor Based Cascadable Voltage Mode First Order All Pass Filters

New Simple Square-Rooting Circuits Based on Translinear Current Conveyors

A High-Gain, Low-Noise GHz Ultra-Wideband LNA in a 0.18μm CMOS

Design of Positive Feedback Driven Current-Mode Amplifiers Z-Copy CDBA and CDTA, and Filter Applications

INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY

Copyright 2007 Year IEEE. Reprinted from ISCAS 2007 International Symposium on Circuits and Systems, May This material is posted here

Voltage Mode First Order All Pass Filter Design Using DX-MOCCII

PLEASE SCROLL DOWN FOR ARTICLE. Full terms and conditions of use:

Simulation of Soft-Switched Three-Phase Inverter for RL and Induction Motor Load

Inter-Ing INTERDISCIPLINARITY IN ENGINEERING SCIENTIFIC INTERNATIONAL CONFERENCE, TG. MUREŞ ROMÂNIA, November 2007.

Research Article Current Mode Full-Wave Rectifier Based on a Single MZC-CDTA

Research Article Quadrature Oscillators Using Operational Amplifiers

SOLIMAN A. MAHMOUD Department of Electrical Engineering, Faculty of Engineering, Cairo University, Fayoum, Egypt

Analysis of Active Feedback and its Influence on UWB Low Noise Amplifier

REALIZATION OF A HIGH OUTPUT EMPEDANCE CMOS DO-OTA WITH EXTENDED LINEARITY RANGE

Generation of Voltage-Mode OTRA-Based Multifunction Biquad Filter

NEW ELECTRONICALLY TUNABLE GROUNDED INDUCTOR SIMULATOR EMPLOYING SINGLE VDTA AND ONE GROUNDED CAPACITOR

Research Article Active Comb Filter Using Operational Transconductance Amplifier

PLEASE SCROLL DOWN FOR ARTICLE. Full terms and conditions of use:

CURRENT-MODE CCII+ BASED OSCILLATOR CIRCUITS USING A CONVENTIONAL AND MODIFIED WIEN-BRIDGE WITH ALL CAPACITORS GROUNDED

Research Article Electronically Controllable Sinusoidal Oscillator Employing CMOS VD-DIBAs

PROGRAMMABLE CURRENT-CONVEYOR-BASED OSCILLATOR EMPLOYING GROUNDED

Research Article Single-Input Four-Output Current Mode Filter Using Operational Floating Current Conveyor

Supplementary First-Order All-Pass Filters with Two Grounded Passive Elements Using FDCCII

Research Article Sinusoidal Generator with π/4-shifted Four/Eight Voltage Outputs Employing Four Grounded Components and Two/Six Active Elements

Novel MOS-C oscillators using the current feedback op-amp

AND LOWPASS FILTERS CURRENT-MODE GROUNDED-CAPACITOR SINGLE-ELEMENT-CONTROLLED BANDPASS

Quadrature Oscillator: A New Simple Configuration based on 45nm 2 nd Generation CMOS Current Controlled Current Conveyor

High Q Active Inductors Apply in A 2.4GHz Bandpass Filter

A Modified Bipolar Translinear Cell with Improved Linear Range and Its Applications

A New Design Technique of CMOS Current Feed Back Operational Amplifier (CFOA)

AND DIFFERENTIATOR DIGITALLY PROGRAMMABLE INTEGRATOR

Research Article Third-Order Quadrature Oscillator Circuit with Current and Voltage Outputs

Current Controlled Current Conveyor (CCCII) and Application using 65nm CMOS Technology

Design Of The Miller Opamp

Wien oscillators using current conveyors

Tunable Gm-C Floating Capacitance Multiplier

Transconductance Amplifier Structures With Very Small Transconductances: A Comparative Design Approach

A CURRENT MIRROR BASED TWO STAGE CMOS CASCODE OP-AMP FOR HIGH FREQUENCY APPLICATION

A Novel Continuous-Time Common-Mode Feedback for Low-Voltage Switched-OPAMP

CURRENT-CONTROLLED SAWTOOTH GENERATOR

Constant-Power CMOS LC Oscillators Using High-Q Active Inductors

A New Architecture for Rail-to-Rail Input Constant-g m CMOS Operational Transconductance Amplifiers

Low-Voltage Wide Linear Range Tunable Operational Transconductance Amplifier

A new high frequency realization of Chua s chaotic circuit using current feedback operational amplifiers (CFOA s)

Improved Linearity CMOS Multifunctional Structure for VLSI Applications

Improved Implementation of Sprott s Chaotic Oscillators Based on Current-Feedback Op Amps

PDm200B High Performance Piezo Driver

A Novel Design Based Approach of High Performance CMOS Based Comparator Using PSpice

Design methodology of Miller frequency compensation with current buffer/amplifier

A Gate-Leakage Insensitive 0.7-V 233-nW ECG Amplifier using Non-Feedback PMOS Pseudo-Resistors in m N-well CMOS

VOLTAGE DIFFERENCING TRANSCONDUCTANCE AMPLIFIERS BASED MIXED-MODE QUADRATURE OSCILLATOR

Designing CMOS folded-cascode operational amplifier with flicker noise minimisation

Low Power Analog Multiplier Using Mifgmos

Advanced Materials Manufacturing & Characterization. Active Filter Design using Bulk Driven Operational Transconductance Amplifier Topology

REALIZATION OF SOME NOVEL ACTIVE CIRCUITS SYNOPSIS

NOVEL OSCILLATORS IN SUBTHRESHOLD REGIME

An Analog Phase-Locked Loop

Research Article A New Translinear-Based Dual-Output Square-Rooting Circuit

A Pedagogical Approach for Modeling and Simulation of Switching Mode DC-DC Converters for Power Electronics Course

A new class AB folded-cascode operational amplifier

New Four-Quadrant CMOS Current-Mode and Voltage-Mode Multipliers

A NEW CMOS DESIGN AND ANALYSIS OF CURRENT CONVEYOR SECOND GENERATION (CCII)

GBM8320 Dispositifs Médicaux Intelligents

PDm200 High Performance Piezo Driver

Cascode Configuration

ECEN474/704: (Analog) VLSI Circuit Design Spring 2018

NEW CFOA-BASED GROUNDED-CAPACITOR SINGLE-ELEMENT-CONTROLLED

Sigma-Delta A/D Modulator Design in a Pre-Diffused Digital Array Using the Principle of Trapezoidal Association of Transistors

GBM8320 Dispositifs Médicaux Intelligents

PARTIALLY ACTIVE-R GROUNDED-CAPACITOR

Transcription:

Circuits and Systems, 20, 2, 6573 doi:0.4236/cs.20.220 Published Online April 20 (http://www.scirp.or/journal/cs) ElectronicallyControlled CurrentMode Second Order Sinusoidal Oscillators Usin MOOTAs and Grounded Capacitors Data Ram Bhaskar, Kasim Karam Abdalla, Raj Senani 2 Department of Electronics and Communication Enineerin, Faculty of Enineerin and Technoloy, Jamia Millia Islmia, New Delhi, India 2 Division of Electronics and Communication Enineerin, Netaji Subhas Institute of Technoloy, Delhi, India Email: senani@nsit.ac.in Received December 7, 200; revised February 9, 20; accepted February 2, 20 Abstract Five new electronicallycontrollable second order currentmode sinusoidal oscillators usin three multioutput operational transconductance amplifiers (MOOTAs) and two rounded capacitors (GC) have been presented. Simulation results are included to confirm the theoretical analysis based upon CMOS OTAs implementable in 0.5 µm technoloy. Keywords: Oscillators, Analo Electronics, Current Mode Circuits, Operational Transconductance Amplifiers. Introduction Recently, Tsukutani, Sumi and Fukui [] presented two currentmode OTAC sinusoidal oscillators each of which employs three MOOTAs and three rounded capacitors (GC) and provides three explicit current outputs. However, whereas one of the circuits of [] does not have independent controllability of the condition of oscillation (CO) and the frequency of oscillation (FO) throuh different transconductances (which is not only a desirable but also an expected property which one likes to see in any OTAC oscillator), on the other hand, both the circuits employ three GCs and hence, are not canonic. The main objective of this paper is to present five new currentmode electronicallycontrollable second order sinusoidal oscillators which use only three MOOTAs like the circuits of [] but in contrast to the circuits of [], the proposed circuits use no more than two GCs and are capable of providin a noninteractin and independent control of both CO and FO and in addition also provide quadrature outputs which find numerous applications (for instance, in communications for quadrature mixers and sinlesideband enerators and in instrumentation for vector enerator or selective voltmeters [2] etc.). 2. The Proposed Circuits The proposed circuits are shown in Fiure. For an ideal MOOTA with transconductance m, the current output I o is iven by I o = m (V V ), where V and V are the input voltaes at noninvertin input terminal and invertin input terminal respectively. Routine analysis yields, the condition of oscillation (CO) and the frequency of oscillation (FO) for all circuits as summarized in Table, which also shows the relevant modes of availability of quadrature outputs in all cases. From the expressions of FO iven in Table, it can be easily deduced that manitude of all active and passive sensitivities of FO, in all the five circuits, would be in the rane of 0 to /2 and circuits thus, enjoy low sensitivity properties. 3. Simulation Results To verify the validity of the proposed confiurations, circuit simulation of the oscillators has been carried out usin the CMOS MOOTA circuit from [] (presented here as Fiure 2). In PSPICE simulation, implementation was based upon a CMOS OTA in 0.5 µm technoloy. The aspect ratios of the MOSFETs were taken as shown in Table 2. The CMOS OTAs were biased with DC power supply voltaes V DD = 2.5 V, V SS = 2.5 V. The enerated waveforms, transient and the frequency spectrum for the proposed circuits obtained from simulations are shown in Fiure 3, Fiure 4 and Fiure 5,

66 D. R. BHASKAR ET AL. m2 m2 I o2 02 m3 m3 m m I o3 03 C I o0 C 2 2 m2 I o202 C I o0 m C 2 2 m3 I o303 m m I o I 0 m2 I o2 02 C I o2 02 m3 C I o2 02 I o 0 C (2) () m3 m3 m2 (3) m2 I o3 03 (4) I o303 C 2 2 C 2 m I o3 03 C 2 m I o 0 (5) Fiure. Proposed confiurations. respectively. The element values used in the simulations alon with the theoretical and practical output frequency and total harmonic distortions (THD) for the proposed circuits are summarized in Table 3. All the proposed oscillators have been checked for robustness usin MonteCarlo simulations, however, to conserve space, a sample result has been shown in Fiure 6 for the oscillator (5) of Fiure, which confirms that for 5% variations in the value of m3, the value of oscillation frequency remains close to its normal value of.996 MHz and hence almost unaffected by chane in m3 (which should be the case since m3 does not feature in the expression of FO). In all cases, a very ood correspondence between desined values and those observed from PSPICE simulations has been obtained. The simulation results, thus, confirm the workability of the proposed confiurations. 4. Comparison with Other Previously Known OTABased Oscillators It is now useful to compare the proposed new circuits with some of the earlier proposed OTAbased oscillators. Recently, Kamat, Anand Mohan and Prabhu [3] presented a quadrature oscillator employin two MOOTAs, two sinle output OTAs and two GCs. The circuit does not have independent controllability of CO and FO. It may also be recalled in this context that much earlier, in reference [4], two minimumcomponent electronicallytunable sinusoidal oscillators usin two OTAs and two GCs had been presented however, these circuits too did not have independent controllability of CO and FO. Furthermore, there is another class of OTAbased RC oscillators known earlier [59] which employ one or two OTAs alon with a number of resistors and two capacitors. However, when these OTARC oscillators from [59] can be transformed into OTAC oscillators, by simulatin the resistors with OTAs, the resultin entirelyotabased oscillators will

D. R. BHASKAR ET AL. 67 V DD V DD M 9 M M 3 M 4 5 M 6 M 0 I I o V in M M V in 2 in in I o o I I bias M 7 M 8 M M 2 Fiure 2. MOOTA. V SS SS Table. Condition of oscillation and frequency of oscillation for the proposed circuits. Circuit No. Condition of Oscillation (CO) ( m3 m ) 0 2 ( m2 m ) 0 3 ( m m2 ) 0 4 (C 2 m3 C m ) 0 5 ( m2 m3 ) 0 Frequency of Oscillation (FO) mm2 CC 2 m2m3 CC 2 m2m3 CC 2 mm2 CC 2 mm2 CC 2 Availability of Quadrature Outputs Io2 s m2 Io2 s m m2, Io s sc2 Io3 s m3sc2 Io3 s m3 Io3 s m3, for m = m2 Io s sc Ios sc Io3 s m3 Io3, s m3 for m = m2 Io s sc Ios sc Io s m Ios sc Io s m2m Io s m, Io3 s m3sc Ios sc Table 2. Aspect ratios of MOSFETs used in the MOOTA implementation. MOSFET W(µm) L(µm) M, M 2 20.8 M 3, M 4, M 5, M 6, M 9, M 0 43 0.5 M 7, M 8, M, M 2 43.25 not remain as efficient and practically viable due to the requirement of an excessive number of OTAs. In comparison, the new circuits are free from above mentioned deficiencies of the circuits presented earlier in [39]. 5. Concludin Remarks Five new currentmode electronically controllable OTAC sinusoidal oscillators have been presented. Like the recently proposed circuits of [], the proposed circuits also employ only three MOOTAs and rounded capacitors as preferred for IC fabrication [0] and []. However, by contrast to the circuits presented in [] both of which require three capacitors and hence are noncanonic, the proposed circuits require only two capacitors and hence, are canonic. All the proposed circuits enjoy the feature of independent controllability of oscillation frequency and condition of oscillation, which is not available in one of the circuits presented in []. The new circuits are also free from the drawbacks of the circuits presented earlier in [39]. Also, all the proposed circuits provide quadrature outputs as an additional feature not available in the circuits of []. The active and passivesensitivities of all the circuits are very low. The workability

68 D. R. BHASKAR ET AL. (a) (b) (c) (d)

D. R. BHASKAR ET AL. 69 (e) Fiure 3. Output waveforms of (a) circuit (b) circuit 2 (c) circuit 3 (d) circuit 4 (e) circuit 5. (a) (b) (c)

70 D. R. BHASKAR ET AL. (d) (e) Fiure 4. Output transient of (a) circuit (b) circuit 2 (c) circuit 3 (d) circuit 4 (e) circuit 5. (a) (b)

D. R. BHASKAR ET AL. 7 (c) (d) (e) Fiure 5. Frequency spectrum of (a) circuit (b) circuit 2 (c) circuit 3 (d) circuit 4 (e) circuit 5. of the proposed circuits has been demonstrated by SPICE simulation results. The transconductance of an OTA is temperature dependent this calls for appropriate temperature compensation for which numbers of schemes are known in the literature [24]. However, the study of modified versions of the proposed circuits incorporatin temperature compensation would require considerable additional work; therefore, it was considered to be outside the scope of present work. Lastly, it may be mentioned that the

72 D. R. BHASKAR ET AL. Fiure 6. Result of the MonteCarlo Simulation of oscillator circuit (5) of Fiure. Circuit No. m (ma/v) Table 3. The values of the capacitors and transconductances for various oscillators. I b (ma) m2 (ma/v) I b2 (ma) m3 (ma/v) I b3 (ma) C (nf) C 2 (nf) F Theoretical (MHz) F Practical (MHz) 0.7954 2.8 0.7954 2.8 0.72.47 0. 0..26598.277 2.6% 2 0.793 2.73 0.75.5 0.804 3.4 0.2 0..0566.803 5.2% 3 0.7523.95 0.794 2.75 0.778 2.26 0.07 0.07.732487.734.6% 4 0.7954 2.8 0.7046.4 0.788 2.6 0. 0..08357.54 2.3% 5 0.785 2.53 0.75.5 0.777 2.36 0. 0..9236.996 % THD circuits proposed in this paper are inspired by the ideas contained in [59]. 6. References [] T. Tsukutani, Y. Sumi and Y. Fukui, Electronically Controlled CurrentMode Oscillators Usin MOOTAs and Grounded Capacitors, Frequenz, Vol. 60, No. 2, 2006, pp. 220223. doi:0.55/freq.2006.60.2.220 [2] W. Tansrirat, Current Differencin Transconductance AmplifierBased CurrentMode FourPhase Quadrature Oscillator, Indian Journal of Enineerin and Material Sciences, Vol. 4, No. 4, 2007, pp. 289294. [3] D. V. Kamat, P. V. A. Mohan and K. G. Prabhu, Novel FirstOrder and SecondOrder CurrentMode Filters Usin MultipleOutput Operational Amplifiers, Circuits Syst Sinal Process, Vol. 29, No. 3, 200, pp. 553576. doi:0.007/s0003400963y [4] M. T. Abuelma atti, New Minimum Componet Electronically Tunable OTAC Sinusoidal Oscillators, Electronics Letters, Vol. 25, No. 7,989, pp. 45. doi:0.049/el:9890747 [5] M. T. Abuelma atti and M. H. Khan, Grounded Capacitor Oscillators Usin a Sinle Operationl Transconductance Amplifier, Active and Passive Electronic Components, Vol. 9, No. 2, 996, pp. 998. [6] Y. Tao and J. K. Fidler, Generation of SecondOrder SinleOTA RC Oscillators, IEE Proceedins of Circuits Devices Systems, Vol. 45, No. 4, 998, pp. 27277. doi:0.049/ipcds:998872 [7] Y. Tao and J. K. Fidler, Electronically Tunable DualOTA SecondOrder Sinusoidal Oscillator/Filters with Noninteractin Controls: A Systematic Synthesis Approach, IEEE Transactions on Circuits Systems I, Vol. 47, No. 2, 2000, pp. 729. [8] V. Sinh, Equivalent Forms of DualOTA RC Oscillators with Application to GroundedCapacitor Oscillators, IEE Proceedins of Circuits Devices Systems, Vol. 53, No. 2, 2006, pp. 9599. doi:0.049/ipcds:20050099 [9] V. Sinh, Equivalent Forms of SinleOperational Transconductance Amplifier RC Oscillators with Application to GroundedCapacitor Oscillators, IET Circuits Devices Systems, Vol. 4, No. 2, 200, pp. 2330. doi:0.049/ietcds.2009.046 [0] B. Bhushan and R. W. Newcomb, Groundin of Capacitors in Interated Circuits, Electronics Letters, Vol. 3, No. 4, 967, pp.4849. doi:0.049/el:96704 [] R. Senani, Realization of a Class of Analo Sinal Processin/Sinal Generation Circuits: Novel Confiura

D. R. BHASKAR ET AL. 73 tion Usin CurrentFeedback OpAmps, Frequenz, Vol. 52, No. 90, 998, pp. 96206. doi:0.55/freq.998.52.90.96 [2] H. S. Malvar and M. Luetten, Temperature Compensation of OTABased Filters and Multipliers, Electronics Letters, Vol. 23, No. 7, 987, pp. 89089. doi:0.049/el:9870629 [3] W.S. Chun, H.W. Cha and K.H. Kim, Temperature Stable VCO Based on Operational Transconductance Amplifiers, Electronics Letters, Vol. 26, No. 22, 990, pp. 90090. doi:0.049/el:990223 [4] C. A. Karybakas, C. Kosmatopoulos and T. Laopoulos, Improved Temperature Compensation of OTAs, Electronics Letters, Vol. 28, No. 8, 992, pp. 763764. doi:0.049/el:9920482 [5] R. Senani, M. P. Tripathi, D. R. Bhaskar and A. K. Banerjee, Systematic Generation of OTAC Sinusoidal Oscillators, Electronics Letters, Vol. 26, No. 8, 990, pp. 457459. doi:0.049/el:9900935 [6] D. R. Bhaskar, M. P. Tripathi and R. Senani, A Class of ThreeOTATwoCapacitor Oscillators with Noninteractin Controls, International Journal of Electronics, Vol. 74, No. 3, 993, pp. 459463. doi:0.080/0020729308925849 [7] D. R. Bhaskar, M. P. Tripathi and R. Senani, Systematic Derivation of All Possible Canonic OTAC Sinusoidal Oscillators, Journal of the Franklin Institute, Vol. 330, No. 5, 993, pp. 885903. doi:0.06/0060032(93)900837 [8] R. Senani, New Electronically Tunable OTAC Sinusoidal Oscillator, Electronics Letters, Vol. 25, No. 4, 989, pp. 286287. doi:0.049/el:989099 [9] M. T. Abuelma atti, Two New Interable ActiveC OTABased Voltae (Current) Controlled Oscillators, International Journal of Electronics, Vol. 66, No., 989, pp. 3538. doi:0.080/0020728908925369