echnical data sheet S--MF- Multifunctional rotary actuator for butterfly valves orque 00 Nm Nominal volta e V Control: ontrol configurable confi urable Position feedback: configurable Auxiliary u iliary switches State at loss of signal: closed echnical data Electrical data Nominal voltage AC V, 50/60 Hz AC/DC V, 50/60 Hz Power supply range AC/DC.6... 6. V Power consumption 80 W @ nominal torque Current consumption 6.0 A Auxiliary switch x EPU, 5 A, AC 30 V II Switching points: 90 Connection erminals, x.5 mm or x.5 mm Parallel connection Supply voltage Not possible Controller signals Only possible for -lead connection For 3-lead connection For -lead connection Functional data Variable Settings orque (nominal torque) Min. 00 Nm @ nominal voltage Control Control signal DC 0... 0 V, input impedance 00 k Starting point DC 0.5... 30 V Operating range DC 0.5... 0 V End point DC.5... 3 V... Control Control signal ma... 0 ma Non-variable Position feedback Measuring voltage U 5 DC 0... 0 V, max. 0.5 ma Starting point DC 0.5... 8 V DC... 0 V, max. 0.5 ma End point DC.5... 0 V... ma... 0 ma Non-variable Position accuracy ±5% absolute Manual override emporary with handwheel (not revolving) Angle of rotation 90 (internal limit switch) Angle of rotation limiting MAX (maximum position) = 00% MAX = (MIN + 3 )... 00% MIN (minimum position) = 0% MIN = 0%... (MAX 3 ) ZS (intermediate position) = 50% ZS = MIN... MAX... Running time 6 s Duty cycle 75% (e.g. 6s / 6s) Sound power level Max. 70 db (A) Position indication Mechanical (integrated) Safety Protection class III Safety extra-low voltage Degree of protection IP67 EMC Low-voltage directive CE according to 00/08/EC CE according to 006/95/EC Certification ested in accordance with EN 6000-6- : 005 EN 6000-6- : 007 Mode of operation ype (EN 60730-) Rated impulse voltage 500 V (EN 60730-) Control pollution degree (EN 60730-) Ambient temperature 0... +60 C Medium temperature 0... +0 C (in the butterfly valve) max. 30 C / h Non-operating temperature 30... +80 C Ambient humidity 95% r.h., non-condensating (EN 60730-) Maintenance Maintenance-free www.belimo.com 5-S--MF- en v.0 0.009 Subject to changes / 7
S--MF- AC/DC V, 00 Nm echnical data Mechanical data Connection flange Housing material (continued) ISO 5 / F0 Cast aluminium Dimensions / Weight Dimensions See «Dimensions» on page 6 Weight Approx. kg Safety notes! he actuator has been designed for use in stationary heating, ventilation and air conditioning systems and is not allowed to be used outside the specified field of application, especially in aircraft or in any other airborne means of transport. It may only be installed by suitably trained personnel. Any legal regulations or regulations issued by government agency authorities must be observed during assembly. he device does not contain any parts that can be replaced or repaired by the user. he device contains electrical and electronic components and is not allowed to be disposed of as household refuse. All locally valid regulations and requirements must be observed. Product features Mode of operation he actuator is controlled with a standard modulating signal and travels to the position defined by the control signal. he measuring voltage U serves for the electrical display of the actuator position 0... 00% and as slave control signal for other actuators. Parameterisable actuators Simple direct mounting Manual override Internal heating Input and output signals and other parameters can be altered with the BELIMO Service ool, MF-P. Simple direct mounting on the butterfly valve. he mounting position in relation to the butterfly valve can be selected in 90 steps. he butterfly valve can be closed (turn clockwise) and opened (turn counterclockwise) with the handwheel. he handwheel does not move while the motor is running. An internal heater prevents condensation buildup. High functional reliability Mechanical stops limit the actuator to and 9. he internal limit switches interrupt the voltage supply to the motor. In addition, a motor thermostat provides overload protection because at 35 C it interrupts the voltage supply. Combination butterfly valve actuators For suitable butterfly valves, their permitted media temperatures and closing pressures are refered to the butterfly valve documentation. Accessories Description Electrical accessories PC-ool MF-P, beginning with v3.3 Cable ZK6-EN Cable ZK-EN / 7 5-S--MF- en v.0 0.009 Subject to changes www.belimo.com
S--MF- AC/DC V, 00 Nm Restrictions for 3-lead (and -lead) connector technologies Description he following overview shows the differences between the V actuator wiring options. he same PCB (Print) can be used for both wirings. 3-lead connection Signal and connection to power supply have the same ground connection Supply voltage AC only AC / DC Maximum cable length* he maximum cable length is defined in the following connection diagram: -lead connection Wire cross-section 0.75 mm.00 mm.50 mm.50 mm No limitation S m 7 m m 3 m No limitation S 3 m 7 m m 3 m No limitation S 5 m 7 m 0 m 7 m No limitation S 5 5 m 7 m 0 m 7 m No limitation Measuring voltage is stable as soon as the actuator stops No limitation Signal and connection to power supply have different ground connections Control signal ma Not possible he ground connection must be wired to the actuator with ma control signal * he limitation regarding cable length is because of the large amounts of current required by the S actuator. A high level of current will in turn have an influence on the signals. 3-lead system connection Measuring voltage U 5 Control signal (-) of the control signal, (-) of the measuring voltage U 5 and can be connected together. Maximum cable length Measuring voltage U 5 Control signal Maximum cable length Electrical installation for 3-lead connection Wiring diagrams AC V U 5 Control signal Measuring voltage A B C D E F 00% 0% Actuator Butterfly valve A AB = 00% A AB = 0% Auxiliary Position Butterfly valve switch 00% open 0% closed www.belimo.com 5-S--MF- en v.0 0.009 Subject to changes 3 / 7
S--MF- AC/DC V, 00 Nm Functions with basic values - 3-lead connection technology Override control with AC V with relay contacts Override control with AC V with rotary control switch a b c e.g. N 007 (DC 0... 0 V) From controller Functions a b c Loss of control signal CLOSED 0% ZS 50% (intermediate position) 3 (DC 0... 0 V) From controller e.g. N 007 Pos Functions Loss of control signal CLOSED 0% ZS 50% (intermediate position) 00% 3 00% Control mode in acc. with Control mode in acc. with Remote control 0... 00% Minimum limit 3 Z SA SF SE Positioner 3 Z SA SF SE Positioner [ ] DIP switch on = V DIP switch on = V (DC 0... 0 V) From controller 0 min 0 [%] 0 00 Master/Slave control (position-dependent) ZAD Adapting the direction of rotation + 3 Control with... 0 ma via external resistance 500 ( )... 0 ma (+) U DC... 0 V he 500 resistor converts the... 0 ma current signal to a voltage signal DC... 0 V Functions for MF actuators with specific parameters - 3-lead connection technology 3-point control Open-close control + a b Direction of rotation switch U a b U Stop Stop / 7 5-S--MF- en v.0 0.009 Subject to changes www.belimo.com
S--MF- AC/DC V, 00 Nm Restrictions for -lead (and 3-lead) connector technologies Description he following overview shows the differences between the V actuator wiring options. he same PCB (Print) can be used for both wirings. 3-lead connection Signal and connection to power supply have the same ground connection Supply voltage AC only AC / DC Maximum cable length* he maximum cable length is defined in the following connection diagram: -lead connection Wire cross-section 0.75 mm.00 mm.50 mm.50 mm No limitation S m 7 m m 3 m No limitation S 3 m 7 m m 3 m No limitation S 5 m 7 m 0 m 7 m No limitation S 5 5 m 7 m 0 m 7 m No limitation Measuring voltage is stable as soon as the actuator stops No limitation Signal and connection to power supply have different ground connections Control signal ma Not possible he ground connection must be wired to the actuator with ma control signal * he limitation regarding cable length is because of the large amounts of current required by the S actuator. A high level of current will in turn have an influence on the signals. -lead system connection Measuring voltage U 5 Control signal (-) of the control signal and (-) of the measuring voltage U 5 can also be connected together. Electrical installation for -lead connection Wiring diagrams AC/DC V U 5 Control signal Measuring voltage A B C D E F 00% 0% Actuator Butterfly valve A AB = 00% A AB = 0% Auxiliary Position Butterfly valve switch 00% open 0% closed www.belimo.com 5-S--MF- en v.0 0.009 Subject to changes 5 / 7
C / C (ccw) S--MF- AC/DC V, 00 Nm Dimensions [mm] Dimensional drawings 39 7 0 90 37 9 SW 35 F0 ( 0) x M0 Settings Setting cam Important! Settings are only allowed to be made by authorised specialist personnel. he setting cams for limit and auxiliary switches can be accessed by removing the housing cover. Optionally, auxiliary switches / can be connected for signaling. Limit switches LS/LS interrupt the voltage to the motor and are controlled by setting cams C... he setting cams turn with the spindle. he butterfly valve closes when the stem is turning clockwise (cw) and opens when the stem is turning counterclockwise (ccw). Stem LS LS C C3 C C Settings of setting cams C.. C for auxiliary switch position closed (factory setting 3 ). C3 for auxiliary switch position open (factory setting 87 ). C for limit switch closed (factory setting 0 ). C for limit switch open (factory setting 90 ). Adjusting setting cams Use a.5 mm Allen key to unscrew the corresponding setting cams C.. urn the setting cam using the Allen key 3 Set as shown in the illustration below Use the Allen key to tighten the setting cams C3 / C (cw) C3 / C (ccw) C / C (cw) CLOSED Current position Desired position Adaptation An adaptation must take place after the C and C have been adjusted. 6 / 7 5-S--MF- en v.0 0.009 Subject to changes www.belimo.com
S--MF- AC/DC V, 00 Nm Settings (continued) Mechanical angle of rotation limitation he mechanical angle of rotation is set at the factory to 9 and cannot be changed. he handwheel is rotated by means of a worm gear in a planetary gear unit. he gearing is stopped mechanically by means of two setscrews and (½ rotations of the setscrews correspond to ). Both limit switches LS /LS are set to 90 and must always switch off the motor before the mechanical angle of rotation limitation. A B C A Angle of rotation limiting (90 ) B Angle of rotation limiting CLOSED (0 ) C Connection of handwheel for angle of rotation limiting Relationship between mechanical angle of rotation limiting, limit and auxiliary switches 0 3 87 90 9 3 Auxiliary switch C3 / C Limit switch C / C 3 Mechanical angle of rotation limitation (A + B) Connection and function elements A B C D E F F3 C C S S reen LED ellow LED Further documentation / Power supply voltage Direction of rotation switch Actuator rotates counterclockwise (ccw), valve opens Direction of rotation switch Actuator rotates clockwise (cw) valve closes Control signal Position feedback / 0-lead (ground) F3 PC-tool connection S Adaptation button Adaptation procedures is started (press S for 3 s) Adaptation must take place after the C and C have been adjusted. ellow LED On Adaptation procedure activated Off Standard operation reen LED On In operation Off No voltage supply or fault Plug-in fuse ype 0A50V Auxiliary switch Factory setting 87 Auxiliary switch Factory setting 3 C / C Not used S Not used Complete overview «he complete range of water solutions» Data sheets, butterfly valves Installation instructions for actuators and/or butterfly valves, respectively Notes for project planning (hydraulic characteristic curves and circuits, installation regulations, commissioning, maintenance. etc.) 7 / 7 5-S--MF- en v.0 0.009 Subject to changes www.belimo.com
S..--..- 7098-0000.A 00% SW DN5... DN00 = SW 7 DN50... DN350 = SW ± 3 5 6 OPE N CLOSED CLOSED CLOSED CLOSED x M8 3 0 Nm S... S3 = SW 3 x M0 3 0 Nm S... S5 = SW 7 www.belimo.com M5-S..--..- v.0 0.009 / 3
S..--..- 5mm A B C D E F F3 C C S S S..--SR- / S..--MF- / S..--MP- S..--SR- / S..--MF- ( ) ( ) ( ) AC V U 5 AC/DC V U 5 A B C D E F A B C D E F 00% 0% 00% 0% A AB = 00% A AB = 0% A AB = 00% A AB = 0% / 3 M5-S..--..- v.0 0.009 www.belimo.com
S..--..- S..--MP- L max. MP Master AC V AC V AC V 8 AC/DC V / AC/DC V / MP MP AC/DC V / AC/DC V p / MP MP U 5 A B C D E F 00% 0% www.belimo.com M5-S..--..- v.0 0.009 3 / 3