IP FITTINGS FOR LUPLST NORD-LINE /S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ 9, DK-9240 NIE TEL: (+4) 98 3 1 00
3 FITTINGS FOR LUPLST NORD-LINE Table of Contents Profile - luplast Nord-Line 4 FITTINGS IP No. 6174 90 mm Window hinge IP No. 6198 120 mm Door hinge 6 PGE IP No. 6269 Fitting for side swing window 7-8 IP No. 6244-2 Reversible Projecting Gears 9-10 IP No. 6262 Safety Restrictor 9-10 IP No. 6270-7 Canopy Stay 11-12 IP No. 6286-87 djustable Canopy Stay 13-14 IP No. 6288 djustable Canopy Stay - djustable Friction 1-16 IP No. 6236 Safety Restrictor 17-18 IP No. 6227 Friction Stay for windows 19 IP No. 6311 Friction Stay for doors 20 IP No. 62222 Support Fitting 21 IP No. 63230 Guide lock 21 IP No. 6308-09 Flush olt 21 IP No. 21371 Casement Hook 22-23 IP No. 21379 Casement Hook 22-23 IP No. 21382 Hook Catch 22-23 IP No. 21383-86 Casement Fasteners 22-23 IP No. 21393-96 Casement Fasteners 22-23 Lubrication Instructions 24-2 Espagnolettes 26
4 FITTING INSTRUCTIONS LUPLST NORD-LINE PROFILE 2,6 12,2 2,6 12,2 11,7 12,2 11,7 11,7 2,4 2,4 2,4 2,6
WINDOW HINGE IP No. 6174 C IP NO. MTERIL STEEL FIXED STEEL PIN STEEL FIXED RSS PIN SQURE EDGES LEFT SQURE EDGES RIGHT SURFCE GLVNIZED INDUSTRY PCKING IN OXES OF 100 PIECES MM MM C MM MTERIL MM PIN MM SCREW PPROX. WEIGHT KG / PC. 6174 2 3 3 4 87 2 90 38. 38. 2. 8 4.0 0.17 IP No. 6174 FITTING INSTRUCTIONS 2,6 LUPLST NORD-LINE PROFILE 11,7 2,4 12,2 FIG. 1 FIG. 2 USE SCREW NO. 4.0. MINTENNCE: TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWICE YER. SEE LSO INSTRUCTIONS ON PGE 24-2.
6 DOOR HINGE IP No. 6198 C MTERIL SURFCE IP NO. STEEL FIXED STEEL PIN STEEL FIXED RSS PIN SQURE EDGES LEFT 6198 2 3 3 4 87 2 120 49 41 4.0 9..0 0.43 FITTING INSTRUCTIONS 2,6 11,7 2,4 SQURE EDGES RIGHT GLVNIZED INDUSTRY PCKING IN OXES OF 0 PIECES MM MM C MM MTERIL MM PIN MM SCREW PPROX. WEIGHT KG / PC. IP No. 6198 LUPLST NORD-LINE PROFILE 12,2 FIG. 1 FIG. 2 USE SCREW NO..0. MINTENNCE: TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWICE YER. SEE LSO INSTRUCTIONS ON PGE 24-2.
SIDE SWING WINDOW 90 0 WITH FRICTION IP No. 6269 7 MTERIL SURFCE IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRDPCKING IN OXES OF SETS MM MM C MM SCREW PPROX. WEIGHT KG / SET 6269 1 7 8 21 1 23 29. 32 4.0 0.44 DJUSTLE FRICTION CONVENIENT FOR CLENING SWINGS 90 OPENS CLER FROM CURTINS ND WINDOW FRME MX. VENTILTION CONCELED FITTINGS NODIZED LUMINIUM RILS C TOP FITTING OTTOM FITTING 1 SET RIGHT HND FIRE-ESCPE OPENING: 00 MM FROM SSH HEIGHT 726 MM
8 IP No. 6269 FITTING INSTRUCTIONS 16.2 LUPLST NORD-LINE PROFILE 16.2 2.4 FIG. 2 HORIZONTL PLN HINGE SIDE FITTING SHOWN ON FRME CILL RIGHT HND ILLUSTRTION IP NO. 6269 MX. WEIGHT OF SSH KGS 40 MIN. WIDTH OF SSH MM 31 FIG. 1 VERTICL PLN MX. WIDTH OF SSH MM 820 USE SCREW NO. 4,0 FIG. 3 FITTING: 1. THE FITTING SHOULD E POSITIONED IN THE GROOVES T HED ND CILL OF FRME ND SCREWED ON (FIGURE 1 ND 2) 2. NOW PUSH THE WINDOW SSH INTO POSITION Y SSH SLOTS ND FSTEN THE SCREWS. 3. THE FRICTION CN NOW E DJUSTED ON THE TOP FITTING. IF LRGER OPENING IS WNTED THEN JUST MOVE THE DJUSTLE STOP FITTING IN THE TOP FRME LUMINIUM RIL. MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE 24-2.
REVERSILE PROJECTING GERS IP No.s 6244-2 & IP No. 6262 9 IP NO. MTERIL STEEL W/O SPECIFICTIONS SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 1 SET MM MM FRME DIMENSIONS INSIDE MM SCREW PPROX. WEIGHT KG / SET 6244 1 0 21 1 18 44 44-643 4.0 1.08 624 1 0 21 1 18 644 644-743 4.0 1.26 6246 1 0 21 1 18 744 744-843 4.0 1.44 6247 1 0 21 1 18 844 844-943 4.0 1.62 1/2 SET 6248 1 0 21 1 18 944 944-1043 4.0 1.80 6249 1 0 21 1 18 1044 1044-1143 4.0 1.98 620 1 0 21 1 18 1144 1144-1243 4.0 2.16 621 1 0 21 1 18 1244 1244-1343 4.0 2.34 622 1 0 21 1 18 1344 1344-1443 4.0 2.2 CONSELED FITTING DJUSTLE FRICTION FULLY REVERSILE 170 0 OPENS CLER OF CURTINS ND WINDOW FRME NODIZED LUMINIUM RILS FIRE-ESCPE OPENING: 00 MM FROM IP No. 6247 600 MM FROM IP No. 6249 MTERIL SURFCE IP NO. STEEL LEFT ELECTROPLTED STNDRD PCKING IN OXES OF 20 PCS. MM SCREW PPROX. WEIGHT KG / PC. 6262 1 7 21 1 170 3. 0.08 SFETY RESTRICTOR IP NO. 6262
10 IP No.s 6244-2 FITTING INSTRUCTIONS LUPLST NORD-LINE PROFILE 2.6 FIG. 2 FIG. 3 TOP FRME 16.2 FRME SIDE 11.7 16.2 16.2 2.4 SSH SIDE TOP SSH 12.2 12.2 16.2 SSH IP NO. 6262 FITTING ON FRME FIG. 1 11.7 2.4 FITTING: 1. PLCE FITTING INTO OTH SIDES OF THE FRME. 2. POSITION FITTING GINST TOP FRME ND FSTEN. 8, - 9 3. PLCE THE ERING PLTE GINST THE TOP ND GINST THE LUMINIUM RIL ND FSTEN. 4. INSERT THE SSH ETWEEN HINGE RMS ND PUSH THE SSH GINST THE STOP RCKET. FSTEN THE SSH STRTING WITH THE SCREW IN THE STOP RCKET.. NOW THE FRICTION CN E DJUSTED Y MENS OF THE SCREWS T THE OTTOM OF THE LU-RILS. THE FRICTION HS TO E THE SME ON OTH SIDES. IP N0. FITTING LENGTH MM MX. WEIGHT KGS. 6244 44 4 624 644 4 6246 744 4 6247 844 4 6248 944 4 6249 1044 4 620 1144 4 621 1244 4 622 1344 4 USE THE LRGEST POSSILE FITTING 6. FIT THE RESTRICTOR IP NO. 6262 ON THE LEFT SIDE, SEE FIG. 1. USE SCREW NO. 4.0. OPERTION INSTRUCTIONS: 1. OPEN THE WINDOW - THE RESTRICTOR WILL UTOMTICLLY RESTRICT THE WINDOW. 2. PULL THE SSH 20 MM - PRESS THE RESTRICTOR IN THE DIRECTION OF THE RROW ND OPEN THE WINDOW. 3. WHEN THE WINDOW IS REVERSED FOR CLENING, THE RESTRICTOR WITH LOCK UTOMTICLLY. DISENGGE S MENTIONED IN POINT 2. MINTENNCE: THE FITTINGS RE NOT TO E PINTED. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HERFTER LIRICTE MINIMUM TWICE YER. DO NOT GRESE THE LUMINIUM RILS. TEST THE OPERTION FROM TIME TO TIME. SEE LSO INSTRUCTIONS ON PGE 24-2.
CNOPY STY WITH FRICTION IP No.s 6270-7 11 MTERIL SURFCE IP NO. STEEL W/O SPECIFICTION ELECTROPLTED STNDRDPCKING IN OXES OF SETS INDUSTRY PCKING IN OXES OF 2 SETS MM MM SCREW PPROX. WEIGHT KG / SET 6270 1 0 21-2 23 2 4.0 0.44 6273 1 0 21-2 23 44 4.0 0.64 6274 1 0 21 1-23 703 4.0 1.02 627 1 0 21 1-23 12 4.0 0.26 CONCELED FITTINGS DJUSTLE FRICTION NODIZED LUMINIUM RILS THE MOVEMENT GEOMETRY ENSURES MXIMUM SELING 1/2 SET FIRE-ESCPE OPENING: IP NO. 6270 00 MM FROM SSH HEIGHT 826 MM IP NO. 6273 00 MM FROM SSH HEIGHT 926 MM 600 MM FROM SSH HEIGHT 1026 MM IP NO. 6274 00 MM FROM SSH HEIGHT 1126 MM 600 MM FROM SSH HEIGHT 1326 MM 627 6270-74
12 IP No. 6270-7 FITTING INSTRUCTIONS LUPLST NORD-LINE PROFILE 2,6 11,7 2,4 FIG. 1 12,2 FIG. 2 IP NO. 6270 6273 6274 627 MX. SSH WEIGHT KGS 40 0 70 20 MX. SSH HEIGHT MM 840 1340 140 300 SCREW 4.0 4.0 4.0 4.0 FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE OTTOM HOLE OF THE FITTING. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. ON IP NO. 6274 MOUNT THE STOPPLTE THROUGH THE UPPER SCREWHOLE UNDER THE SLIDDING ELEMENT. 2. PUSH THE SSH INTO ITS PLCE Y INSERTING IT ETWEEN THE FITTINGS, GUIDED Y THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. THESE STOPS WILL GURNTEE MM G ETWEEN FRME ND SSH. FSTEN THE FITTING STRTING WITH THE SCREW IN THE STOP RCKET (IP NO. 6270-74). 3. NOW THE FRICTION MY E DJUSTED Y MENS OF THE SCREWS IN THE SLIDES. THE EST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED Y EQUL FRICTION T EITHER SIDE. MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE 24-2. FIG. 3
DJUSTLE CNOPY STY WITH FRICTION IP No.s 6286-87 13 MTERIL SURFCE IP NO. STEEL W/O SPECIFICTION ELECTROPLTED INDUSTRY PCKING IN OXES OF 2 SETS MM MM SCREW PPROX. WEIGHT KG / SET 6286 1 0 21 2 23 306 4.0 0.3 6287 1 0 21 2 23 496 4.0 0.74 1/2 SET CONCELED FITTINGS DJUSTLE FRICTION VERTICLLY DJUSTLE ± 1. MM NODIZED LUMINIUM RILS THE MOVEMENT GEOMETRY ENSURES MXIMUM SELING FIRE-ESCPE OPENING: IP NO. 6286 00 MM FROM SSH HEIGHT 826 MM IP NO. 6287 00 MM FROM SSH HEIGHT 926 MM 600 MM FROM SSH HEIGHT 1026 MM
14 IP No. 6286-87 FITTING INSTRUCTIONS 2,6 LUPLST NORD-LINE PROFILE 11,7 2,4 FIG. 1 12,2 FIG. 2 IP NO. 6286 6287 MX. SSH WEIGHT KGS 40 0 MX. SSH HEIGHT MM 840 1340 SCREW 4.0 4.0 FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE OTTOM HOLE OF THE FITTING. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. 2. PUSH THE SSH INTO ITS PLCE Y INSERTING IT ETWEEN THE FITTINGS, GUIDED Y THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. THESE STOPS WILL GURNTEE MM G ETWEEN FRME ND SSH. FSTEN THE FITTING STRTING WITH THE SCREW IN THE STOP RCKET ECCENTRIC SCREW 3. NOW THE FRICTION MY E DJUSTED Y MENS OF THE SCREWS IN THE SLIDES. THE EST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED Y EQUL FRICTION T EITHER SIDE. 4. THE SSH CN E DJUSTED ±1. MM UP OR DOWN. EFORE NY DJUSTMENT THE MOUNTING SCREWS IN THE OTTOM IN ECH SIDE OF THE FRME HVE TO E LOOSENED. THEN DJUST Y USING TORX-20 KEY TO TURN THE ECCENTRIC SCREW. Y DELIVERY THE MRK ON THE ECCENTRIC SCREW IS IN VERTICL PERSITION INDICTING THE 0-POSITION. WHEN THE MRK IS IN HORIZONTL POSTION IN EITHER TOP OR OTTOM, THE FITTING IS DJUSTED TO IT S MX OF ±1. MM. FTER THE DJUSTMENT THE MOUNTINGSCREWS IN THE OTTOM OF ECH SIDE RE FSTENED. MRK FIG. 3 MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE 24-2.
DJUSTLE CNOPY STY WITH DJUSTLE FRICTION IP No. 6288 1 MTERIL SURFCE IP NO. STEEL W/O SPECIFICTION ELECTROPLTED STNDRD PCKING IN OXES OF SETS MM MM SCREW PPROX. WEIGHT KG / SET 6288 1 0 21 1 23 37 4.0 0.76 1/2 SÆT VERTICLLY DJUSTLE ± 1. MM DJUSTLE FRICTION CONCELED FITTINGS NODIZED LUMINIUM RILS THE MOVEMENT GEOMETRY ENSURES MXIMUM SELING FIRE-ESCPE OPENING: IP NO. 6288 00 MM FROM SSH HEIGHT 626 MM 600 MM FROM SSH HEIGHT 726 MM
16 IP No. 6288 FITTING INSTRUCTIONS 2,6 LUPLST NORD-LINE PROFILE 11,7 2,4 FIG. 1 12,2 FIG. 2 IP NO. 6288 FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE OTTOM HOLE OF THE FITTING. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. MX. SSH WEIGHT KGS 0 MX. SSH HEIGHT MM 940 SCREW 4.0 2 PUSH THE SSH INTO ITS PLCE Y INSERTING IT ETWEEN THE FITTINGS, GUIDED Y THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. THESE STOPS WILL GURNTEE MM G ETWEEN FRME ND SSH. FSTEN THE FITTING STRTING WITH THE SCREW IN THE STOP RCKET 3. NOW THE FRICTION MY E DJUSTED Y MENS OF THE SCREWS IN THE SLIDES. WHEN DJUSTING LET THE TOP GLIDER MOVE DOWN TO THE STOP. THE EST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED Y EQUL FRICTION T EITHER SIDE. 4. THE SSH CN E DJUSTED ±1. MM UP OR DOWN. EFORE NY DJUSTMENT THE MOUNTING SCREWS IN THE OTTOM IN ECH SIDE OF THE FRME HVE TO E LOOSENED. THEN DJUST Y USING TORX-20 KEY TO TURN THE ECCENTRIC SCREW. Y DELIVERY THE MRK ON THE ECCENTRIC SCREW IS IN VERTICL PERSITION INDICTING THE 0-POSITION. WHEN THE MRK IS IN HORIZONTL POSTION IN EITHER TOP OR OTTOM, THE FITTING IS DJUSTED TO IT S MX OF ±1. MM. FTER THE DJUSTMENT THE MOUNTINGSCREWS IN THE OTTOM OF ECH SIDE RE FSTENED. ECCENTRIC SCREW MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE 24-2. MRK FIG. 3
17 SFETY CTCH IP No. 6236 MTERIL SURFCE IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRDPCKING IN OXES OF SETS MM SCREW PPROX. WEIGHT KG / SET 1 SET RIGHT 6236 1 7 8 21 1 92 4.0 0.06
18 IP No. 6236 FITTING INSTRUCTIONS LUPLST NORD-LINE PROFILE MRK SIDE FRME X + 86 SSH X 12,2 2,6 11,7 OTTOM FRME 2,4 FIG. 1 RIGHT HND ILLUSTRTION FIG. 2 THE FITTING CN E USED ON OTH TOPHUNG/TOPGUIDED S WELL S SIDEHUNG/SIDEGUIDED WINDOWS. ON TOPHUNG/TOPGUIDED WINDOWS THE RESTRICTOR IS PLCED IN THE OTTOM OF THE SIDE FRME ND THE RECEIVER IS PLCED IN THE OTTOM OF THE SIDE SSH. ON THE SIDEHUNG/SIDEGUIDED WINDOWS THE RESTRICTOR IS PLCED IN TOP/OTTOM FRME ON THE OPPOSITE SIDE OF THE HINGES ND THE RECEIVER IS PLCED IN THE TOP/OTTOM SSH OPPOSITE THE HINGES. X-DIMENSION IS OPTIONL. ON TOPHUNG/TOPGUIDED WINDOWS X MUST MINIMUM E 7 MM. Y USING LRGER X-DIMENSION THE VENTILTION OPENING WILL E EXTENDED. IMPORTNT: THE RECEIVER MUST E MOUNTED SO THT IT HITS THE MRK ON THE RESTRICTOR RM WHEN THE WINDOW IS CLOSED. SEE FIG. 1 OPERTING INSTRUCTIONS: 1. OPEN THE WINDOW UNTIL THE RESTRICTOR ENGGES. 2 PULL THE SSH PPROXIMTELY 20 MM CKWRDS. 3. PRESS THE RESTRICTOR OUTWRDS S YOU OPEN THE WINDOW. 4. WHEN THE WINDOW IS CLOSED THE RESTRICTOR RE-ENGGES UTOMTICLLY. USE SCREW NO. 4.0 MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE 24-2.
19 FRICTION STY for windows IP No. 6227 IP NO. MTERIL STEEL W/O SPECIFICTION SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 2 PCS. MM MM MTERIL MM SCREW PPROX. WEIGHT KG / PC. 6227 1 0 21 1 19 274 17X3 4.0 0.14 CONCELED FITTING OPENS UP TILL 100 FRICTION IN LL POSITIONS DJUSTLE FRICTION NODIZED LUMINIUM RIL IP No. 6227 FITTING INSTRUCTIONS 100 274 LUPLST NORD-LINE PROFILE 2.6 16.2 TOP FRME FIG. 2 11.7 13 30 FIG. 1 DJUSTLE FRICTION TOP SSH 12.2 16.2 MINTENNCE: THE FITTING RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN MOUNTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HERFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RIL. SEE LSO INSTRUCTIONS ON PGE 24-2. FIG. 3
20 FRICTION STY for doors IP No. 6311 IP NO. MTERIL STEEL W/O SPECIFICTIONS SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 10 PCS. PPROX. WEIGHT KG / PCS. 6311 1 0 21 1 19 414 17X3 4.0 0.22 MM MM MTERIL MM SCREW CONCELED FITTING OPENS UP TILL 100 FRICTION IN LL POSITIONS DJUSTLE FRICTION NODIZED LUMINIUM RIL IP No. 6311 FITTING INSTRUCTIONS 20 414 LUPLST NORD-LINE PROFILE TOP FRME 2.6 16.2 200 30 FIG. 1 DJUSTLE FRICTION FIG. 2 TOP SSH 12.2 16.2 11.7 MINTENNCE: THE FITTING RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN MOUNTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HERFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RIL. SEE LSO INSTRUCTIONS ON PGE 24-2. FIG. 3
21 CCESSORIES IP No.s 62222, 63230 & 6308-09 C SUPPORT FITTING IP NO. 62222 C GUIDE LOCK IP NO. 63230 IP N0. MTERIL LUMINIUM PLSTIC W/O SPECIFICTION SURFCE NODIZED GREY STNDRD PCKING IN OXES OF 20 PCS. STNDRD PCKING IN OXES OF 2 PCS. MM MM C MM SCREW HOLES MM SCREW PPROX. WEIGHT KG / PC. 62222 0-0 00 - - 1 70 16 12.0-0.0 63230-9 0-4 1-42 20 10-4.0 0.04 FLUSH OLT IP NO. 6308 FLUSH OLT IP NO. 6309 IP NO. MTERIL STEEL SQURE EDGES SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 10 PCS. MM MM THICKNESS MM OLT MM LENGTH OLT MM SCREW PPROX. WEIGHT KG / PC. 6308 1 21 1 128 19 6 8.X2. 1 3. 0.04 6309 1 21 1 128 19 6 8.X2. 20 3. 0.04
22 CSEMENT HOOKS, HOOK CTCH & CSEMENT FSTENERS FITTING INSTRUCTIONS MTERIL SURFCE IP NO. ZINK LLOY WITHOUT SPECIFICTION ELECTROPLTED / WHITE ELECTROPLTED ELECTROPLTED YELLOW STNDRDPCKING IN OXES OF 0 PIECES INDUSTRY PCKING IN OXES OF 20 PIECES MM MM HOLE FOR PIN MM PPROX. WEIGHT KG / 100 PIECES 21371 0 0 06 21 2-2 130 9 6 6.0 21379 0 0 - - 2 1-120 93 6.6 21371 21379 21386 21393 21394 21396 IP NO. MTERIL STEEL RSS W/O SPECIFICTION ELECTROPLTED / WHITE PHOSPH. ROWN SURFCE ELECTROPLTED ELECTROPLTED YELLOW POLISHED STNDRD PCKING IN OXES OF 2 PIECES STNDRD PCKING IN OXES OF 0 PIECES INDUSTRY PCKING IN OXES OF 200 PIECES INDUSTRY PCKING IN OXES OF 20 PIECES INDUSTRY PCKING IN OXES OF 00 PIECES MM MM RING SCREW THRED MM PIN MM SCREW PPROX. WEIGHT KG/100 PCS. 21383 21382 21382 1-0 - - 21 2 - - 1-2 - 13.3 34 -,6 3. 0.7 21383 1-0 - - 21 2 - - - - - 2 0 20-3. 4.0 21386 1-0 06-21 2 - - 1 - - 2 4 0 1-3..0 1-0 - 12 - - - - 1 - - - 21393 1-0 06-21 2 - - 1 - - 2 9 0 20-3. 4.4-6 0 - - - - 8-1 2 - - 21394 1-0 - - 21 2-1 - - - - 9 0 20-3..0 21396 1-0 - - 21 2 - - - - - 2 0 20-3..0
23 FITTING INSTRUCTIONS IP NO.S 21371 + 21379 + 21382 DRILL MM HOLE FOR RING SCREW 3. 13 13 13 28, 28 22 13 IP NO. 21382 IP NO.S 21386 + 21393-94 SSH FRME 18 FRME 12 10 28 22 7 28, SSH MONTERUNG: 1. MOUNT THE RECEIVER IN THE WNTED HEIGHT ON THE SIDEFRME. 2. IP NO. 21386 + 21393-94: FOR CSEMENT FSTENERS WITH SCREW PLTE MESURE PRECISELY ON THE SSH ND DRILL MM HOLE FOR THE RING SCREW. MRK UP THE 2 SCREW HOLES ON THE SCREW PLTE ND FSTEN THE CSEMENT FSTENER..
24 MINTENNCE FITTING INSTRUCTIONS LURICTION INSTRUCTIONS IP NO. 6244-2 IP NO. 6270-7 IP NO. 6286-88 IP NO. 6269 IP NR. 6174 IP NR. 6198 GENERLLY all parts of a building have to be looked after and maintained from time to time. This of course also applies for fittings in windows and doors. How often fittings in windows and doors should be maintained depends to a large extent on how they are used, how often they are operated, and not least on the environment the fittings are exposed to. Corrosion may also be caused by other factors, such as corrosive liquids, air pollution etc. Special attention should be given to fittings used in windows and doors in urban and industrial areas or other areas with a high traffic intensity as well as coastal areas. Fittings in such environments should be checked and greased more often than fittings used in areas with less corrosive effects. HINGES ND FITTINGS should be lubricated when necessary, or at the minimum twice a year. SLIDING ELEMENTS S WELL S LL LURILS with sliding surfaces are to be kept clean and free from dust and dirt to ensure a smooth sliding function. Stearin wax or a clean lubricating film (but no oil and no grease!) can be applied onto the alluminium rails. ESPGNOLETTES ND OTHER LOCKING FITTINGS should be greased or lubricated with acid free grease or acid free oil on spray. The grease/oil should be applied into the mechanism box as well as on the joints of the side bolts, the roller bolts, or the mushroom head bolts while activating the mechanism repeatedly. Grease or lubricate when necessary or at the minimum twice a year. Continues...
2 MINTENNCE LURICTION INSTRUCTIONS RSS will sooner or later get some discoloration in a brownish tone depending on the environment in which it is placed. The original brass surface can be maintained by polishing from time to time. STINLESS STEEL can get some discoloration, although this rarely happens. Different chemical influences like acid fumes, contamination from wood preservation treatments, or air pollution may cause discoloration of the metal, sometimes to a reddish tone which could look like rust. Thin discoloration can be removed just by using common cleaner or polish. PINTED FITTINGS will from time to time need repainting. efore painting all parts should be cleaned carefully. When choosing type of paint and when applying the paint remember to follow the instructions from the paint manufacturer very carefully. When painting a wooden window in a house, it is a good idea also to paint the visible parts of the fittings (please note: No alurails nor sliding parts should ever be painted!). The painting of the fitting will minimize corrosion and add to the lifetime of the fitting. lways make sure that the proper function of a fitting is not affected by the painting. NODIZED LUMINIUM should be cleaned from time to time, depending on the surroundings in which it is placed. Cleaning of the surface with a cloth or sponge is recommended. Eventually a neutral solvent can be used. Emery cloth, steel wool, sodium carbonate, and other cleansers or abrasives containing alkalies or acid should never be used. ON THE WINDOW ND DOOR FCTORY SITE all fittings should be lubricated or greased before shipment. Hinges should be lubricated with acidfree oil while activating repeatedly, an acidfree grease can also be used. When using grease it should be applied directly onto the pin of the hinges. It may be necessary to dismantle the sash before greasing. Especially hinges with a brass pin should be greased. When mounting fittings, please make sure that the tools do not damage the original surface treatment. When original surface has been damaged make sure that remedial take place as soon as possible. WHEN IN DOUT PLESE CONTCT YOUR LOCL SUPPLIER OR /S J. PETERSENS ESLGFRIK.
26 FITTING PSKVILER INSTRUCTIONS IP HS LRGE PROGRMME OF ESPGNOLETTE OLTS WHICH SLIGHTLY MODIFIED CN E USED IN THE LUPLST NORD-LINE PROFILE. EXMPLE IP NO.S 23701-10 RECEIVER IP NO. 6322 HNDLE IP NO. 23228 SK YOUR DELER OR CONTCT IP DIRECTLY FOR MORE INFORMTION.
/S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ 9, DK-9240 NIE TEL.: (+4) 98 3 1 00 www.ipafittings.com ipa@ipafittings.com Printed 03/2011