SHD TO REMOVE HOOD (SHD) ) LOOSEN (4) SOCKET HEAD SCREWS AND RETAINING RINGS FROM HOOD (SHD). ) REMOVE HOOD AND. 3) DISCONNECT WIRES. 3 4) REMOVE REFLECTOR BY LOOSENING (4) PHILIPS HEAD SCREWS. 5) PLEASE PROCEED TO INSTALLATION INSTRUCTION OF FOR SYMMETRICAL REFLECTOR & INSTALLATION. RETAINER HOOD 3 4X /4-0 X /" SOCKET HEAD CAP SCREW S/S 4X RETAINING RING E-STYLE 7/3" S/S 4X /4-0 X 3/8" PHILIPS HEAD SCREW OF
SYM SYMMETRIC REFLECTOR & INSTALLATION ) SEE INSTRUCTION OF BEFORE PROCEEDING. ) CONNECT WIRES, WHITE TO WHITE AND BLACK TO BLACK WITH BUTT CONNECTORS. SECURE SYMMETRIC REFLECTOR WITH (4) PHILIPS HEAD SCREWS. ( PLEASE BE CAREFUL NOT TO PINCH WIRES WHEN INSTALLING SYMMETRICAL REFLECTOR. 3) INSTALL LAMP. 4) INSTALL SYMMETRIC TO SYMMETRIC REFLECTOR. SECURE SYMMETRIC WITH (4) CLIPS. 5) INSTALL TO ITS ORIGINAL POSITION AND SECURE WITH (4) BUTTON HEAD SCREWS. 6) INSTALLATION COMPLETE. (4) RETAINING RING SYMMETRIC (4) /4-0 BUTTON HEAD SCREWS (4) CLIPS (4) /4-0 X 3/8" PHILIPS HEAD SCREW SYMMETRIC REFLECTOR (REFERENCE) LAMP HOUSING SYMMETRIC (4) CLIPS OF
ASH ) REMOVE (4) SOCKET HEAD SCREW AND RETAINING RING FROM ORIGINAL. ) RE-ALIGN HOOD AND AS SHOWN. (BE SURE LAMP IS IN THE OPEN HOOD SIDE). 3) SECURE HOOD TO HOUSING WITH (4) SOCKET HEAD CAP SCREWS AND (4) RETAINING RINGS. RETAINER BARN DOORS HOOD 4X /4-0 X /" SOCKET HEAD CAP SCREW S/S BARN DOORS (ASH) 4X RETAINING RING E-STYLE 7/3" S/S 9/05/008 A963
CFH ) ASSEMBLE FRAME AS SHOWN IN "FIGURE A". (TAKE CARE NOT TO OVER TIGHTEN (4) 8-3 SCREWS). GLASS WILL BREAK. ) REMOVE (4) SOCKET HEAD SCREW AND RETAINING RING FROM ORIGINAL. 3) RE-ALIGN HOOD AND AS SHOWN. (BE SURE LAMP IS IN THE OPEN HOOD SIDE). 4) SECURE HOOD TO HOUSING WITH (4) SOCKET HEAD CAP SCREWS AND (4) RETAINING RINGS. RETAINER COLOR FILTER HOOD COLOR FILTER HOOD (CFH) "FIGURE A" COLOR FILTER COVER FRAME ASS'Y HOOD FRAME ASS'Y 4X /4-0 X /" SOCKET HEAD CAP SCREW S/S 4X RETAINING RING E-STYLE 7/3" S/S (4) 8-3 SCREWS A9633
PRF ) REMOVE (4) SOCKET HEAD SCREW AND RETAINING RING FROM ORIGINAL. ) RE-ALIGN FASCIA AND AS SHOWN. (BE SURE LAMP IS IN THE OPEN FASCIA SIDE). 3) SECURE HOOD TO HOUSING WITH (4) SOCKET HEAD CAP SCREWS AND (4) RETAINING RINGS. RETAINER FASCIA FASCIA (PRF) 4X /4-0 X /" SOCKET HEAD CAP SCREW S/S 4X RETAINING RING E-STYLE 7/3" S/S A9634
RCK ) REMOVE (4) SOCKET HEAD SCREW AND RETAINING RING FROM ORIGINAL. ) RE-ALIGN ROCK GUARD HOOD AND AS SHOWN. (BE SURE LAMP IS IN THE OPEN ROCK GUARD HOOD SIDE). 3) SECURE HOOD TO HOUSING WITH (4) SOCKET HEAD CAP SCREWS AND (4) RETAINING RINGS. RETAINER ROCK GUARD HOOD 4X /4-0 X /" SOCKET HEAD CAP SCREW S/S ROCK GUARD (RCK) 4X RETAINING RING E-STYLE 7/3" S/S A9635
SHD ) REMOVE (4) SOCKET HEAD SCREW AND RETAINING RING FROM ORIGINAL. ) RE-ALIGN HOOD AND AS SHOWN. (BE SURE LAMP IS IN THE OPEN HOOD SIDE). 3) SECURE HOOD TO HOUSING WITH (4) SOCKET HEAD CAP SCREWS AND (4) RETAINING RINGS. RETAINER HOOD 4X /4-0 X /" SOCKET HEAD CAP SCREW S/S HOOD (SHD) 4X RETAINING RING E-STYLE 7/3" S/S A9636
MST-3D 6X SET SCREWS (/4-0 X 3/8") ) TURN OFF POWER. ) INSTALL STANCHION ALUMINUM POST AS SHOWN. 3) MAKE WIRE CONNECTION FROM FIXTURE TO POLE. ( MUST BE GROUNDED TO INCOMING EQUIPTMENT 4) SLIP FITTER OVER ALUMINUM POST SECURE FITTER WITH (6) STAINLESS SET SCREWS. POST TOP FITTER WIRE CONNECTORS STANCHION 4" O.D. X 8" LONG ALUMINUM POST CONDUIT 0" MAX. 5" MINIMUM CONCRETE STANCHION MOUNT (MST) A9637
MST (6) SET SCREWS (/4-0 X 3/8") WIRE CONNECTORS 0.00" MAX. 5.00" MINIMUM STANCHION 4" O.D. X 8" LONG ALUMINUM POST ) TURN OFF POWER. ) INSTALL STANCHION ALUMINUM POST AS SHOWN. 3) MAKE WIRE CONNECTION FROM FIXTURE TO POLE. ( MUST BE GROUNDED TO INCOMING GROUND SUPPLY.) 4) SLIP FITTER OVER ALUMINUM POST. SECURE FITTER WITH (6) STAINLESS SET SCREWS. CONCRETE CONDUIT STANCHION MOUNT (MST) A9637
CPH-YK ) TURN OFF POWER. () O.50 O.843 ) SECURE FIXTURE TO CONCRETE. 3) MOUNT /" NPT CONNECTOR TO COUPLING. 4) RUN WIRE TO BALLAST. MAKE WIRE CONNECTION. ( MUST BE GROUNDED TO INCOMING LINE). 3.30" 5.55" YOKE HOLES DETAILS USE WEATHER PROOF J-BOX IF CONDUIT IS NOT APPLICABLE X NUT X WASHER X ANCHOR BOLT /" NPT (MALE) CONDUIT CONCRETE YOKE MOUNT (YK) A9638
CPH 90 90 80 0 "FIGURE A" MOUNTING ORIENTATION SILICONE GASKET 5.54 (REF.) (4) /4-0 BUTTON HEAD SCREWS LAMP HOUSING CAST NUTS.50 3.00 6.5 (REF.) BALLAST O.75 4.5 (4) /4-0 HOUSING WIREWAY 8.50 BUTTON HEAD SCREWS "FIGURE C" MOUNTING DETAIL MOUNTING PLATE "FIGURE B" FIXTURE INSTALLATION ) LOOSEN (4) /4-0 BUTTON HEAD SCREWS AT BALLAST HOUSING AND REMOVE FIXTURE (SEE "FIGURE B"). ) REMOVE BALLAST FROM MOUNTING PLATE. 3) SECURE MOUNTING PLATE TO DESIRE LOCATION. PLEASE SEE "FIGURE C" FOR MOUNTING DETAILS. 4) SECURE BALLAST TO MOUNTING PLATE AND MAKE WIRE CONNECTIONS. 5) "FIGURE A" DISPLAY POSSIBLE MOUNTING ORIENTATIONS. TO CHANGE ORIENTATION, LOOSEN CAST NUTS, ROTATE TO THE DESIRE LOCATION AND TIGHTEN CAST NUTS. 6) REMOVE YELLOW NYLON PROTECTOR. 7) INSTALLATION COMPLETE. RELAMP ) LOOSEN (4) /4-0 BUTTON HEAD SCREWS AT LAMP HOUSING. REMOVE. ) INSTALL LAMP. FOR SYMMETRICAL DISTRIBUTION, PLEASE SEE DRAWING # A96343. 3) RETURN TO ITS ORIGINAL POSITION AND SECURE SCREWS. SILICONE GASKET ADHERE TO MOUNTING PLATE TO PREVENT WATER LEAKAGE. NO SILICONE REQUIRED. (4) O.406 MOUNTING HOLES A9639
SPN SET SCREW MOUNTING BRACKET TO BE MOUNTED TO THE J-BOX WIRE LEADS CANOPY STEM (REFERENCE) COUPLING SAFETY CABLE MUST BE SECURE TO SUPER STRUCTURE OF BUILDING. FIXTURE INSTALLATION ) TURN OFF ALL POWER. ) RUN WIRES LEADS AND SAFETY CABLE FROM COUPLING THROUGH STEM. SECURE THE THREADED END OF THE STEM TO THE COUPLING. SCREWS SET SCREWS AT COUPLING. 3) SECURE MOUNTING BRACKET TO J-BOX. 4) SLIP CANOPY OVER STEM. HANG STEM TO THE MOUNTING BRACKET. MAKE WIRE CONNECTIONS FROM J-BOX TO STEM. SECURE SAFETY CABLE TO SUPER STRUCTURE OF BUILDING. 5) SLIDE CANOPY UP, LOCK IT INTO THE MOUNTING BRACKET. 6) INSTALLATION COMPLETE. FIXTURE (REFERENCE) MEANS OF MOUNTING AND MOUNTING HARDWARE. SINGLE PENDANT MOUNT (SPN) A96330
TPN FIXTURE INSTALLATION ) TURN OFF ALL POWER. ) RUN WIRE LEADS AND SAFETY CABLE FROM WIRE HOUSING THROUGH STEM. SECURE THE THREADED END OF THE STEM TO THE COUPLING. SCREW SET SCREW AT COUPLING. 3) SECURE MOUNTING BRACKET TO CEILING. MAKE SURE MOUNTING IS INDEPENDANT OF J-BOX. 4) SLIP CANOPY OVER STEM. HANG STEM TO THE MOUNTING BRACKET. MAKE WIRE CONNECTION FROM J-BOX TO STEM. SECURE SAFETY CABLE TO SUPER STRUCTURE OF BUILDING. SAFETY CABLE MUST BE SECURE TO SUPER STRUCTURE OF BUILDING MOUNTING BRACKET TO BE MOUNTED INDEPENDANT OF J-BOX WIRE LEADS CANOPY STEM (REFERENCE) COUPLING WIRE HOUSING 5) SLIDE CANOPY UP. LOCK IT INTO THE MOUNTING BRACKET. 6) INSTALLATION COMPLETE. SET SCREW FIXTURE (REFERENCE) MEANS OF MOUNTING AND MOUNTING HARDWARE. DUAL PENDANT MOUNT (TPN) A9633
TPN FIXTURE INSTALLATION ) TURN OFF ALL POWER. ) RUN WIRE LEADS AND SAFETY CABLE FROM HOUSING SUPPORT THROUGH STEM. SECURE THE THREADED END OF THE STEM TO THE HOUSING SUPPORT. 3) SECURE MOUNTING BRACKET TO CEILING. MAKE SURE MOUNTING IS INDEPENDANT OF J-BOX. 4) SLIP CANOPY OVER STEM. HANG STEM TO THE MOUNTING BRACKET. MAKE WIRE CONNECTION FROM J-BOX TO STEM. SECURE SAFETY CABLE TO SUPER STRUCTURE OF BUILDING. SAFETY CABLE MUST BE SECURE TO SUPER STRUCTURE OF BUILDING MOUNTING BRACKET TO BE MOUNTED INDEPENDANT OF J-BOX WIRE LEADS CANOPY STEM (REFERENCE) HOUSING SUPPORT 5) SLIDE CANOPY UP. LOCK IT INTO THE MOUNTING BRACKET. 6) INSTALLATION COMPLETE. FIXTURE (REFERENCE) MEANS OF MOUNTING AND MOUNTING HARDWARE. DUAL PENDANT MOUNT (TPN) A9633
SYM SYMMETRIC INSTALLATION ) LOOSEN (4) /4-0 BUTTON HEAD SCREWS AT LAMP HOUSING. ) REMOVE. 3) INSTALL LAMP. 4) INSERT SYMMETRIC TO SYMMETRIC REFLECTOR SECURE SYMMETRIC WITH (4) CLIPS. 5) RETURN TO ITS ORIGINAL POSITION AND SECURE WITH (4) BUTTON HEAD SCREWS. 6) INSTALLATION COMPLETE. (4) /4-0 BUTTON HEAD SCREWS SYMMETRIC (4) CLIPS FOR FIXTURE ORIENTATION AND MOUNTING ORIENTATION PLEASE SEE DRAWING # A9639. SYMMETRIC REFLECTOR (REFERENCE) LAMP HOUSING A96343
SYM SYMMETRIC INSTALLATION ) LOOSEN (4) /4-0 BUTTON HEAD SCREWS AT LAMP HOUSING. ) REMOVE. 3) INSTALL LAMP. 4) INSERT SYMMETRIC TO SYMMETRIC REFLECTOR SECURE SYMMETRIC WITH (4) CLIPS. 5) RETURN TO ITS ORIGINAL POSITION AND SECURE WITH (4) BUTTON HEAD SCREWS. 6) INSTALLATION COMPLETE. FOR FIXTURE ORIENTATION AND MOUNTING ORIENTATION PLEASE SEE DRAWING # A9639. (4) /4-0 BUTTON HEAD SCREWS 4 SYMMETRIC (4) CLIPS SYMMETRIC REFLECTOR (REFERENCE) LAMP HOUSING SYMMETRIC (4) CLIPS A96343