R Long Range Metal Body Sensor 30 m Range With Advanced Fuzzy Logic H Mutual interference protection H NPN/PNP switch selectable output H M12 plug-in connector H Meets IP67 and NEMA 4X, 6P H Vibration resistance of 10 Hz to 2 khz and a shock resistance of 1,000 m/s 2 (approx. 100 G) Ordering Information J SENSORS Mounting Method of detection Sensing distance Part number Pre-leaded Connector Horizontal Through-beam 30 m (98.43 ft) T11 T16 Polarized retroreflective 3 m (9.84 ft) R11 R16 Diffuse reflective 70 cm (27.56 in) D11 D16 2 m (6.56 ft) D12 D17 Vertical Through-beam 30 m (98.43 ft) T61 T66 Polarized retroreflective 3 m (9.84 ft) R61 R66 Diffuse reflective 70 cm (27.56 in) D61 D66 2 m (6.56 ft) D62 D67 J ACCESSORIES Description Slits for E3S--CTjjsensors (4 pairs: 0.5 mm, 1.0 mm, 2 mm, and 4 mm wide, includes mounting hardware) Mounting bracket for E39-R1 reflector Part number E39-S61 E39-L7 J CONNECTOR CABLES Connector type Cable size Length Straight connector Right angle connector 3-wire DC 22 AWG 2 m (6.56 ft) Y96E-43SD2 Y96E-43RD2 MicroChange R 5 m (16.40 ft) Y96E-43SD5 Y96E-43RD5 10 m (32.8 ft) Y96E-43SD10 Y96E-43RD10
J REPLACEMENT PARTS Description Mounting bracket for E3S--Cj1j (horizontal) Mounting bracket for E3S--Cj6j (vertical) Reflector (supplied with retroreflective sensors) Part number E39-L102 E39-L103 E39-R1 Specifications Part number T11 T61 T16 T66 R11 R61 R16 R66 Method of detection Through-beam Polarized retroreflective Supply voltage 10 to 30 VDC, 10% Current consumption 50 ma max. (emitter and 40 ma max. receiver) Sensing distance White mat paper 0to30m (0 to 98.43 ft) With accessories 4-mm slit: 15 m 2-mm slit: 7 m 1-mm slit: 3.5 m 0.5-mm slit: 1.8 m Light source Minimum object size 4-mm slit: 2.6-mm dia. 2-mm slit: 2-mm dia. 1-mm slit: 1-mm dia. 0.5-mm slit: 0.5-mm dia. Pulse modulated infrared LED (880 nm) 0to3m (0 to 9.84 ft) E39-R2: 0 to 4 m E39-R3: 0 to 150 cm E39-R4: 0 to 75 cm E39-RSA: 5to 35cm E39-RSB: 5to 60cm E39-R1 Reflector: 13-mm dia. E39-R3: 8-mm dia. E39-R4: 4-mm dia. Pulse modulated red LED (700 nm) D11 D61 D16 D66 Diffuse reflective 0to70cm (0 to 27.56 in) D12 D62 D17 D67 0to2m (0 to 6.56 ft) Pulse modulated infrared LED (880 nm) Standard object Type Opaque materials Opaque materials Opaque and transparent materials Size 9 mm (3.54 in) min. 30 mm (1.18 in) min. 30 x 30cm (11.81x 11.81in) whitemat paper Operation mode Light-ON/Dark-ON operation, switch selectable Variation in sensing distance -- 10% max. Hysteresis -- 20% max. of sensing distance Variation in optical axis and mounting 2! max. direction Sensitivity Adjustable, 3/4 turn knob Adjustable, 2-1/2 turn knob with clutch and indicator Mutual interference protection Not provided Provided Control output Type NPN or PNP (selectable), open collector current output Max. load 100 ma max. Residual voltage NPN output: 1.2 V max., PNP output: 2.0 V max. Response time OFF 1ms max. 2ms max. ON 1ms max. 2ms max. Circuit protection Output short-circuit protection, reversed polarity protection Vibration resistance Destruction 10 to 2 khz, 1.5-mm double amplitude, or 300 m/s 2 (approx. 30G) 0.5 hrs each in X, Y, and Zaxes Shock resistance Destruction 1,000 m/s 2 (approx. 100G) 3 times each in X, Y, and Z axes (This table continues on the next page.) 2
Part number T11 T61 T16 T66 R11 R61 R16 R66 D11 D61 D16 D66 D12 D62 D17 D67 Indicators Emitter Power ON (red) Stability indicator (green), Light Incident (red) Receiver Stability indicator (green), Light Incident (red) Materials Lens Acrylic Case Zinc die-cast Operation panel Sulfonated polyether Bracket Stainless steel Mounting Either side surface with two threaded holes. Bracket for horizontal (E39-L102) or vertical (E39-L103) sensors and hardware included. Connections Emitters 2-conductor cable, 3-conductor cable, 2 m (6.56 ft) length (for prewired types) 2 m (6.56 ft) length or 4 pin, 12 mm connector Receiver 3-conductor cable, 2 m (6.56 ft) length or 4 pin, 12 mm connector Weight Horizontal model 110 g (3.88 oz.) Vertical model 115 g (4.06 oz.) Enclosure ratings IEC 144 IP67 NEMA 1, 4X, 6P, 12, 13 Ambient Operating -25!C to55!c (-13!F to 131!F) temperature Storage -40!C to70!c (-40!F to 158!F) J OUTPUT CIRCUIT DIAGRAMS Output configuration Mode switch Output transistor Output circuits NPN Light-ON ON when light is Light received. indi- Dark-ON ON when light is not received. cator (Red) Stability indicator PNP output transistor NPN and PNP output selector (See Note.) Brown Black Load 10 to 30 VDC Load current Control output NPN output transistor Blue 0V PNP Light-ON ON when light is Dark-ON ZD : V Z =39 V Note: Photo- (Green) electric sensor main circuit received. Light Stability indi- indicator cator Photo- (Red) (Green) electric sensor main circuit ON when light is not received. Set the NPN and PNP output selector to NPN. PNP output transistor Brown 10 to 30 VDC NPN and PNP Black Control output output selector (See Load Load NPN output Note.) current transistor Blue 0V ZD : V Z =39 V Note: Set the NPN and PNP output selector to PNP. 3
Engineering Data EXCESS GAIN RATIO Tj6 Rj6 (E39-R1 Reflector) Dj6 Excess gain ratio Excess gain ratio Excess gain ratio Distance (m) Distance (m) Distance (cm) Dj2 Dj7 Excess gain ratio Distance (m) OPERATING RANGE Parallel Operating Range (Typical) Tj6 Operating Range (Typical) Dj6 (Left and Right) Dj7 and Dj2 (Left and Right) Parallel operating range Y (cm) Y X Set distance x (cm) Operating position Y (mm) Set distance x (cm) Sensing object Y X Operating position Y (mm) Set distance x (cm) Sensing object X Y Detecting distance X (m) Detecting distance X (cm) Detecting distance X (cm) 4
J SENSING DISTANCE VS. OBJECT SIZE (TYPICAL) Dj6 Dj7 Dj2 Sensing object: White paper Sensing object: White paper Sensing distance (m) OFF ON Sensing distance (m) OFF ON Size of object (cm) Size of object (cm) J REFLECTOR PARALLEL MOVEMENT (TYPICAL) Rj6 Dj7 and Dj2 (Up and Down) Parallel operating range Y (cm) E39-R1 Reflector X Y Set distance X (cm) Operating position Y (mm) Set distance X (cm) Sensing object Y X Detecting distance X (cm) 5
Dimensions Unit: mm (inch) J SENSORS T11, R11 D11, D12 18.5 50 (1.97) Light indicator (red) (0.73) M3 x 5 Vinyl-insulated cord with three conductors, 4 mm OD; standard length: 2 m (6.56 ft.) 20 (0.79) 20.4 Mounting holes 22.2 (0.87) Two, M4 Stability indicator (green) 12 (0.47) 4.2 (0.17) 20 9.2 25.4 4.2 (0.17) (0.79) (0.36) (1.00) Lens (17 x 11) Receiver** 4.2 (0.17) Two mounting holes 8.3 6.2 (0.24) (0.33) 25.4 (1.00) 38.2 (1.50) Optical axis Emitter 2.2 (0.09) 11.5 (0.45) 20.2 Two, M4 23 7.7 (0.30) 29.5 (1.16) 17.3 (0.68) 9.3 (0.37) * The mounting bracket can 20.8 25.4 be attached to side A. 1.5 (0.82) (1.00) (0.06) ** For T11, optical viewing for the emitter and the receiver are from the top portion of the sensor. 6
T61, R61 57 (2.24) Vinyl-insulated cord with three conductors, 4 mm OD; standard length: 2 m (6.56 ft.) D61, D62 20.8 (0.82) Receiver** Emitter Optical Lens (17 x 11) 4 (0.16) dia. 22.2 (0.87) 20 (0.79) 6.1 (0.24) dia. 20.4 Mounting holes axis 12 (0.47) 20 Two, M4 (0.79) 9.2 (0.36) 4.2 (0.17) 25.4 (1.00) Two mounting holes 4.2 (0.17) 5.6 (0.22) 14.4 14.4 (0.57) (0.57) 25.4 (1.00) Stability 31 (1.22) indicator 43.8 (1.72) (green) Light indicator 7.2 (0.28) (red) 2.2 5.8 (0.23) (0.09) 20.2 (0.79) Two, M4 32.2 (1.27) 11.5 (0.45) 23 M3 x 5 12 (0.47) 23.2 * The mounting bracket can 31 be attached to side A. (1.22) ** For T61, optical viewing for the emitter and the receiver are from the top portion of the sensor. 1.5 (0.06) 7
E3S -CT16 74 (2.91) 18.5 (0.73) 50 (1.97) Stability indicator (receiver) (green) M3 x 5 20 (0.79) 20.4 Lens (17 x 11) Optical axis Light indicator (receiver) (red) Power indicator (emitter) (red) 9.2 (0.36) 4.2 Two, Mounting holes 4.2 6.2 25.4 (1.00) 38.2 (1.50) 8.3 (0.33) Mounting holes 22.2 (0.87) 12 Two, M4 (0.47) 42 20 (0.17) (0.79) 25.4 (1.00) 12.7 (0.50) 20.2 2.2 (0.09) 9.3 (A) (See Note.) (0.37) 29.5 (1.16) 17.3 (0.68) Two, M4 11.5 (0.45) 23 Note: Mounting bracket can be attached to side A. 1.5 20.8 (0.06) (0.82) 25.4 (1.00) E3S -CT66 15.8 (0.62) 57 (2.24) Optical axis 74 (2.91) M12 20 20.4 (0.79) Stability indicator (receiver) (green) 7.2 4.4 Lens (17 x 11) Light indicator (receiver) (red) Power indicator (emitter) (red) 2.2 (0.09) Two, Mounting holes 4.2 5.6 14.4 (0.57) 4.2 14.4 (0.57) 25.4 (1.00) 31 (1.22) 43.8 (1.72) 22.2 (0.87) 12 (0.47) 4.2 20 9.2 (0.79) (0.36) Mounting holes Two, M4 25.4 (1.00) Mounting screw holes 5.8 20.2 32.2 (1.27) Two, M4 11.5 (0.45) 23 (A) (See Note.) Note: M3 x 5 Mounting bracket can be attached to side A. 23.2 31 (1.22) 12 (0.47) 1.5 (0.06) 8
R16/-CD16/-CD17 74 (2.91) 50 (1.94) 18.5 (0.73) Stability indicator (green) M3 x 5 20 (0.79) 20.4 Light indicator (red) 22.2 (0.87) 12 (0.47) 9.2 4.2 20 (0.36) 4.2 (0.17) (0.79) Mounting holes Two, M4 25.4 (1.00) Lens (17 x 11) Receiver Two, Mounting holes 4.2 8.3 6.2 25.4 (1.00) 38.2 (1.50) 2.2 20.2 (0.09) Two, M4 29.5 7.7 (1.16) 9.3 (A) (See Optical Emitter (0.37) note) axis 1.5 20.8 25.4 (0.06) (0.82) (1.00) Note: Mounting bracket can be attached to side A. 17.3 (0.68) 11.5 (0.45) 23 R66/-CD66/-CD67 74 (2.91) 57 (2.24) 20.8 (0.82) 9 Optical axis Emitter (0.35) 20 (0.79) 20.4 Receiver 22.2 12 Lens (17 " 11) (0.87) (0.47)20 Mounting holes Two, M4 9.2 4.2 (0.79) 25.4 (1.00) Stability indicator (green) 7.2 4.4 Light indicator (red) Two, Mounting holes 4.2 4.2 5.6 14.4 14.4 (0.57) (0.57) 25.4 (1.00) 31 (1.22) 43.8 (1.72) 2.2 (0.09) 5.8 20.2 32.2 (1.27) Two, M4 11.5 (0.45) 23 (A) (See note) Note: M3 x 5 Mounting bracket can be attached to side A. 12 (0.47) 23.2 31 1.5 (1.22) (0.06) 9
J CORNER CUBE REFLECTORS E39-R1 Retroreflector 40.3 (Included with E3S- CR11/CR61) Two, 3.5 dia. 7 (1.59) 34 (1.34) 7.5 (0.30) 59.9 52 (2.36) (2.05) 62.1 (2.46) 8(0.31) 1.6 2.7 (0.06) (0.11) E39-S61 Slit Kit for See note 0.2 (0.01) 11 (0.43) 20 (0.79) 6.2 11.8 (0.24) (0.46) 6.5 (0.26) 20.1 (0.79) Note: 3.8 (0.15) This size is 0.5 mm, 1 mm, 2 mm, or 4 mm depending on the type. 10
Nomenclature J OPERATION PANEL Use the NPN and PNP output selector on the operation panel to select the type of output transistor. Use the Light-ON and Dark-ON selector on the operation panel to select the operation mode of the. Horizontal Model Vertical Model Stability indicator (green) Light incident indicator (red) Stability indicator (green) Light incident indicator (red) Sensitivity adjuster L-ON and D-ON selector Sensitivity adjuster Model Number NPN and PNP output selector NPN and PNP output selector L-ON and D-ON selector 11
Operation J FUZZY LOGIC MUTUAL INTERFERENCE PREVENTION FUNCTION (FOR Rjj AND Djj ONLY) When the risk is high, the emits light between each light interference moment. If photoelectric sensors are installed side by side, each Sensor may be influenced (or malfunction) by the light emitted from the other sensors. This is known as mutual interference. The fuzzy logic mutual interference prevention function of the enables the to monitor light interference over a certain period of time. Before the starts emitting light, the retrieves the intensity and frequency of surrounding light interfer- ence as data. Using this data, the calculates, with fuzzy inference, the risk of the malfunctioning and controls the timing of the s light emission. When the risk is low, the waits until there is no light interference and emits light. J SENSITIVITY ADJUSTMENT (REFLECTIVE SENSORS) Light interference Emission pattern Light interference Emission pattern Steps Step 1 Step 2 Step 3 Function Determine position A Determine position B Adjust to optimum setting Sensing Photoelectric sensor Photoelectric sensor Photoelectric sensor condition Sensitivity adjustor Sensing object Sensing object A A B B Sensing object Min. Max. Min. Max. Min. Max. Indicators OFF ON STABILITY (green) LIGHT (red) OFF STABILITY (green) OFF LIGHT (red) OFF STABILITY (green) ON LIGHT (red) Procedure Place target at the desired sensing distance. Set sensitivity adjuster to the minimum scale position, and gradually increase sensitivity by turning the sensitivity adjuster clockwise until the Light Incident indicator (red LED) turns ON. Position A designates the point at which the LED has turned on. Remove the target. Starting from the maximum scale position, gradually decrease sensitivity by turning the sensitivity adjuster counterclockwise until the Light Incident indicator (red LED) turns OFF. Position B designates the point at which the LED has turned OFF. Set the sensitivity indicator to the position between Positions A and B (in some cases, Positions A and B are opposite of the above example). The photoelectric sensor will then work normally if the stability indicator (green) is lit with and without the target. If it is not lit, stable operation cannot be guaranteed,in which case a different detection method should be applied. Unlike conventional photoelectric sensors, the variation in the sensitivity among several photoelectric sensors is minimal. This means the sensitivity can be adjusted on only a single photoelectric sensor, and then the adjusters on the other photoelectric sensors can be set to the same scale position. There should be no need to adjust the sensitivity of each photoelectric sensor individually. 12
Precautions J CONNECTION If the input/output lines of the photoelectric sensor are placed in the same conduit or duct as power lines or high-voltage lines, the photoelectric sensor could be induced to malfunction, or be damaged, by the electrical noise. Either separate the wiring, or use shielded lines as input/output lines to the photoelectric sensor. The cord connected to the can be extended up to 100 m provided that the diameter of each wire of the cord is 0.3 mm 2 minimum. J WATER RESISTANCE To ensure the water resistance of the, tighten the screws of the operation panel cover to a torque of 3.5 to 5.5 kgf S cm (0.34 N S m to0.54n S m). J POWER SUPPLY If the standard switching regulator is used as a power supply, the frame ground (FG) terminal and the ground (G) terminal, on the power supply, must be grounded. If this is not done the may malfunction, due to the switching noise of the power supply. If an inverter motor or servomotor is used with the, the frame ground (FG) terminal and the ground (G) terminal, on the motor, must be grounded, otherwise the may malfunction. Installation J MOUNTING Use M4 screws to mount the. The tightening torque of each screw must be 12 kgf S m (1.18 N S m) maximum. J DIRECT MOUNTING Mount the as shown in the following illustrations. J OPTICAL AXIS OF THROUGH-BEAM SENSOR The through-beam models incorporate two lenses, one of which will be used as shown in the following illustration. When using a slit, the slit must be on the side where the lens is located. Lens in use. The slit must be on this side. Two, 4.5 dia. through holes M4 Lens not in use. M4 hole M4 hole Two, M3 M4 hole M4 hole M3 13
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4. R OMRON ELECTRONICS LLC OMRON ON -LINE OMRON CANADA, INC. One East Commerce Drive Global -- http://www.omron.com 885 Milner Avenue Schaumburg, IL 60173 USA -- http://www.omron.com/oei Scarborough, Ontario M1B 5V8 1-800-55-OMRON Canada -- http://www.omron.com/oci 416-286-6465 Cat. No. CEDSAX4 11/01 Specifications subject to change without notice. Printed in U.S.A.