Remote I/O R9 Series MULTI POWER MOITORIG UIT (Clamp-on current sensor CLSE, CC-Link) Functions & Features Multi Power Monitoring Unit for CC-Link. By using clamp-on current sensors, there is no need of current transformers. Up to 8 circuits can be measured. (Common voltage measurement) Current sensors are easy to install in existing systems. Wide input range of 5 to 600 A is availabe. All measured values, counter values, display mode, setting data are stored in the non-volatile memory when power is off. By using SD card, data logging of current and power etc. with calendar is available. 5 (4.9) EXTESIO UIT : With connection AUXILIARY POWER SUPPLY AD4: universal 00 40 V AC (Operational range 85 64 V, 50 / 60 Hz) / 0 40 V DC (Operational range 99 64 V, ripple 0 %p-p max) [] OPTIOS /Q: With options (specify the specification) SPECIFICATIOS OF OPTIO: Q (multiple selections) COATIG (For the detail, refer to M-System's web site.) /C0: Silicone coating /C0: Polyurethane coating /C0: Rubber coating EX-FACTORY SETTIG /SET: Preset according to the Ordering Information Sheet (o. ESU-6) 40 (5.5) 80 (.5) mm (inch) MODEL: R9CWTU 00 AD4[] ORDERIG IFORMATIO Code number: R9CWTU-00-AD4[] Specify a code from below for []. (e.g. R9CWTU-00-AD4/Q) Specify the specification for option code /Q (e.g. /C0/SET) COFIGURATIO : Single-phase/-wire, -phase/-wire, single-phase/-wire; 8 circuits COECTIO 0: Terminal block I/O 0: Without RELATED PRODUCTS Discrete I/O Extension Unit (model; R9WTU-ED) Multi power Monitoring Extension Unit (model; R9WTU-EP) PC configurator software (model: PMCFG) Downable at M-System s web site. A dedicated cable is required to connect the module to the PC. Please refer to the internet software down site or the users manual for the PC configurator for applicable cable types. Clamp-on current sensor (model: CLSE) The clamp-on current sensors, not included in this product package, must be ordered separately. Required number depends upon the system configuration. SD card A SD card is required to store data in the unit. Use the specified model number of memory card. Available for purchase from M-System. Consult M-System. - Hagiwara Solutions SD6-004GH (S-004GT, S-004GL... discontinued) - Apacer Technology AP-ISD04GIS4B-T (AP-ISD04GIS4B-T... discontinued) GEERAL SPECIFICATIOS Construction: Stand-alone Degree of protection: IP0 Connection Auxiliary power or voltage input: M.5 screw terminals (torque 0.8 m) Current input: M screw terminals (torque 0.5 m) http://www.m-system.co.jp/ R9CWTU SPECIFICATIOS ES-6 Rev.5 Page /
etwork: M screw terminals (torque 0.5 m) Solderless terminal: Refer to the drawing at the end of the section. Recommended manufacturer: Japan Solderless Terminal MFG.Co.Ltd, ichifu Co.,ltd Applicable wire size M screw terminal: 0.5 to.65 mm (AWG to 6) M.5 screw terminal:.04 to.6 mm (AWG 6 to 4) Configuration: Single-phase/-wire, single-phase/-wire, - phase/-wire Screw terminal: ickel-plated steel Housing material: Flame-resistant resin (black) Isolation: Sensor core to sensor output or current input or voltage input to CC-Link to auxiliary power to FE Measured variables Voltage: R, S, T, R S, S T, T R Current: R, S, T, Active / reactive / apparent power: R, S, T, Σ Power factor: R, S, T, Σ Frequency Active energy: Incoming Reactive energy: Incoming lag Active / reactive / apparent power intervals (demand) Average (demand) current: R, S, T, Harmonic contents: Σ Voltage: R -, S -, T -, R - S, S - T, T - R Current: R, S, T, Max. and min. values Calendar log (inserting SD card): Voltage, Current, power, electric energy, power factor Operating mode setting: Connection, clamp-on sensor selection Status indicators: Power, SD Card Recommended solderless terminal size - M 6 (.4) max. (.) max mm (inch) Recommended solderless terminal size - M.5 etwork cable: CC-Link cable designated by Mitsubishi Electric Station number: - 64 (rotary switch) Station Type: Remote device Data allocation: Baud rate setting: 56 kbps (default), 65 kbps,.5 Mbps, 5 Mbps, 0 Mbps (rotary switch) Baud rate setting: Rotary switch 56kbps, 65kbps,.5Mbps, 5Mbps, 0Mbps CC-Link LED: Run, RD, SD, ERR IPUT SPECIFICATIOS Frequency: 50 / 60 Hz (45 65 Hz) Voltage Input Rated voltage Between lines: 400 V AC Line-neutral (phase voltage): 0 V (single-phase / -wire and -wire) Input burden: UL / 00 kω / phase Over capacity: 00 % of rating for 0 sec., 0 % continuous Selectable primary voltage range: 50 400 000 V Current Input CLSE-R5: 0 5 A AC CLSE-05: 0 50 A AC CLSE-0: 0 00 A AC CLSE-0: 0 00 A AC CLSE-40: 0 400 A AC CLSE-60: 0 600 A AC Over capacity: 0 % continous, 500 % for 0 sec. Selectable primary current range: 0 000 A (Using CLSE- R5 the unit is configurable only with configurator software.) Operational range Current: 0 0 % of the rating Voltage: 0 0 % of the rating Apparent power: 0 % of the rating Active/reactive power: ±0 % of the rating Frequency: 45 65 Hz Power factor: ± (. ) max. (. ) max mm (inch) CC-Link COMMUICATIO CC-Link: Ver..0 Station Type: Remote device Connector: M screw terminal ISTALLATIO Auxiliary power supply AC: < 9 VA DC: < W Operating temperature: -0 to +55 C (4 to F) Operating humidity: 0 to 90 %RH (non-condensing) Atmosphere: o corrosive gas or heavy dust Mounting: Surface or DI rail Weight: 500 g (. lb) http://www.m-system.co.jp/ R9CWTU SPECIFICATIOS ES-6 Rev.5 Page /
PERFORMACE Accuracy (at 0-5 C or 50-95 F, 45 65 Hz) * Add the accuracy of the current sensor for overall values. Voltage: ±0.5 % of the rating * Current: ±0.5 % of the rating * Power: ±0.5 % of the rating * Power factor: ±.5 % Frequency: ±0. % of the rating * Energy: ± % Harmonic contents: ± % of the rating * *. Sensor error margin not included *. The described accuracy levels are ensured at the input % or more for phase current with -phase/-wire unbalanced, for neutral current with -phase/4-wire unbalanced, and neutral current with -phase/-wire. Data update period: Harmonic contents and frequency: sec. Other: 500 msec. Calendar clock: (with battery backup) Accuracy: Monthly deviation minutes at 5 C Back up period: Approx. years at 5 C without power With the power on, no battery drain Battery: Primary lithium battery (non-removable) Insulation resistance: 00 MΩ with 500 V DC Dielectric strength: 000 V AC @ minute (current input or voltage input to CC-Link to auxiliary power to FE) EXTERAL VIEW FROT VIEW CC-Link Terminals Terminating Resistor SW 6 5 4 C C FE 9 8ch 8 8ch ch 6 ch 5 6ch 4 6ch 5ch 5ch T 8 8ch 8ch 6 ch 5 ch 4 6ch 6ch 5ch 5ch 0 T Term on Terminal Block, Current Input Station Address Setting Rotary SW STATIO SD Card Slot Baud Rate Setting Rotary SW Operating Mode Setting DIP SW (SW) Terminal Block, Voltage Input / Auxiliary Power Supply 4 5 6 0 ch ch ch ch 4 ch 5 ch 6 4ch 4ch 8 P P C ch ch ch 4 ch 5 ch 6 ch 4ch 8 4ch 9 U(+) V(-) FE C PC Configurator Connection Jack Status Indicator / CC-Link LED Terminal Block, Current Input http://www.m-system.co.jp/ R9CWTU SPECIFICATIOS ES-6 Rev.5 Page /
TERMIAL COECTIOS Use the model CLSE clamp sensor for current inputs. The figure below shows only one circuit. At the maximum of eight (8) current sensor inputs are available (ch through 8ch). Grounding is not required for low voltage circuits. System / Application Terminal System / Application Terminal P P Single-phase / -wire Three-phase / -wire balanced L P P u v u v v u U V k K l L L U V V U k K l L P P P Single-phase / -wire P Three-phase / -wire unbalanced L P P k l K L u v v u U V V U u v v u U V V U L COECTIO DIAGRAMS MASTER COECTIO Master Unit TERMIATOR blue white yellow FG Remote Unit FE Remote Unit TERMIATOR FE Be sure to connect the terminating resistor across and at both ends of communication line. When this unit is located at an end, turn the terminating resistor SW O. The Master Unit can be located at not only both ends but also any node of the of communication line. http://www.m-system.co.jp/ R9CWTU SPECIFICATIOS ES-6 Rev.5 Page 4/
TERMIAL ASSIGMETS CC-Link 6 5 4 C C FE Current Input 9 8ch 8 8ch ch 6 ch 5 6ch 4 6ch 5ch 5ch T 8 8ch 8ch 6 ch 5 ch 4 6ch 6ch 5ch 5ch 0 T o. ID FUCTIO 4 FE CC-Link ground 5 Shield 6 C Unused C Unused Auxiliary Power Supply, Voltage Input 4 5 6 P P U(+) V( ) FE o. ID FUCTIO U(+) Auxiliary power (+) V( ) Auxiliary power ( ) FE Power ground 4 Voltage input 5 P Voltage input P 6 P Voltage input P Voltage input o. ID FUCTIO o. ID FUCTIO 5ch Ch.5, Current input 0 5ch Ch.5, Current input 5ch Ch.5, Current input 5ch Ch.5, Current input 6ch Ch.6, Current input 6ch Ch.6, Current input 4 6ch Ch.6, Current input 6ch Ch.6, Current input 5 ch Ch., Current input 4 ch Ch., Current input 6 ch Ch., Current input 5 ch Ch., Current input 8ch Ch.8, Current input 6 8ch Ch.8, Current input 8 8ch Ch.8, Current input 8ch Ch.8, Current input 9 T Unused 8 T Unused Current Input 0 ch ch ch ch 4 ch 5 ch 6 4ch 4ch 8 C ch ch ch 4 ch 5 ch 6 ch 4ch 8 4ch 9 C o. ID FUCTIO o. ID FUCTIO C Unused 0 C Unused ch Ch., Current input ch Ch., Current input ch Ch., Current input ch Ch., Current input 4 ch Ch., Current input ch Ch., Current input 5 ch Ch., Current input 4 ch Ch., Current input 6 ch Ch., Current input 5 ch Ch., Current input ch Ch., Current input 6 ch Ch., Current input 8 4ch Ch.4, Current input 4ch Ch.4, Current input 9 4ch Ch.4, Current input 8 4ch Ch.4, Current input http://www.m-system.co.jp/ R9CWTU SPECIFICATIOS ES-6 Rev.5 Page 5/
DIMESIOS unit: mm (inch) 6 (.4) 4 M SCREW TERMIAL 4 4.5 (.8) dia. MTG HOLE DI RAIL 5 mm wide 40 (5.5) 6 (4.96) 5 (4.5) (DI RAIL MOUT) 5 (.95) 5 (4.9) 80 (.5) 6.5 (.5) [4 (.6)]. (.9) M.5 SCREW TERMIALS MOUTIG REQUIREMETS unit: mm (inch) SIGLE MOUTIG 5 (.95) 4 M4 6 (4.96) Pitch 0 (5.) min. BASIC + EXTESIO UIT 5 (.95) 0.5 (.8) 6 M4 6 (4.96) Pitch (8.8) min. http://www.m-system.co.jp/ R9CWTU SPECIFICATIOS ES-6 Rev.5 Page 6/
SCHEMATIC CIRCUITRY & COECTIO DIAGRAM AUX. POWER SUPPLY VOLTAGE IPUT U AUXILIARY POWER SUPPLY V FE 4 P 5 VOLTAGE P 6 Isolation Comm. Circuit 5 4 6 FE C To other CC-Link devices COMMUICATIO C 0 Ch. CURRET Ch. 5 CURRET CURRET IPUT Ch. CURRET 4 4 Control Circuit Ch. 6 CURRET 5 5 4 4 CURRET IPUT Ch. CURRET 6 6 5 5 Ch. CURRET 6 6 Ch. 4 CURRET 8 8 Ch. 8 CURRET 9 8 C 9 T C 0 8 T EXTESIO COECTOR Specifications are subject to change without notice. http://www.m-system.co.jp/ R9CWTU SPECIFICATIOS ES-6 Rev.5 Page /