HA523 Data Sheet September 3, 215 FN3393.9 Dual 125MHz Video Current Feedback Amplifier The HA523 is a wide bandwidth high slew rate dual amplifier optimized for video applications and gains between 1 and 1. It is a current feedback amplifier and thus yields less bandwidth degradation at high closed loop gains than voltage feedback amplifiers. The low differential gain and phase,.1db gain flatness, and ability to drive two back terminated 75 cables, make this amplifier ideal for demanding video applications. The current feedback design allows the user to take advantage of the amplifier s bandwidth dependency on the feedback resistor. By reducing R F, the bandwidth can be increased to compensate for decreases at higher closed loop gains or heavy output loads. The performance of the HA523 is very similar to the popular Intersil HA-52. Ordering Information PART NUMBER HA523IPZ (Note) (No longer available, recommended replacement: HA523IBZ) PART MARKING TEMP. RANGE ( C) PACKAGE HA523IPZ -4 to 85 8 Ld PDIP* (Pb-free) PKG. DWG. # E8.3 Features Wide Unity Gain Bandwidth................. 125MHz Slew Rate............................... 475V/ s Input Offset Voltage........................ 8 V Differential Gain............................3% Differential Phase............................3 Supply Current (per Amplifier)................ 7.5mA ESD Protection............................ 4V Guaranteed Specifications at 5V Supplies Pb-Free Plus Anneal Available (RoHS Compliant) Applications Video Gain Block Video Distribution Amplifier/RGB Amplifier Flash A/D Driver Current to Voltage Converter Medical Imaging Radar and Imaging Systems Video Switching and Routing Pinout HA523 (PDIP, SOIC) TOP VIEW HA523IBZ (Note) 523IBZ -4 to 85 8 Ld SOIC (Pb-free) M8.15 OUT1 1 8 V+ HA523IBZ96 (Note) 523IBZ -4 to 85 8 Ld SOIC Tape and Reel (Pb-free) M8.15 *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 1% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-2. -IN1 +IN1 V- 2 3 4 - + + - 7 6 5 OUT2 -IN2 +IN2 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 Intersil (and design) is a registered trademark of Intersil Americas LLC Copyright Intersil Americas LLC 1998, 25-26, 215. All Rights Reserved All other trademarks mentioned are the property of their respective owners.
HA523 Absolute Maximum Ratings Voltage Between V+ and V- Terminals.....................36V DC Input Voltage (Note 3)........................ V SUPPLY Differential Input Voltage...............................1V Output Current (Note 4).................Short Circuit Protected ESD Rating (Note 3) Human Body Model (Per MIL-STD-883 Method 315.7)... 2V Operating Conditions Temperature Range...........................-4 C to 85 C Supply Voltage Range (Typical)................. 4.5V to 15V Thermal Information Thermal Resistance (Typical, Note 2) JA ( C/W) PDIP Package*............................ 13 SOIC Package............................. 16 Maximum Junction Temperature (Note 1)................. 175 C Maximum Junction Temperature (Plastic Package, Note 1).. 15 C Maximum Storage Temperature Range.......... -65 C to 15 C Maximum Lead Temperature (Soldering 1s)............ 3 C (SOIC - Lead Tips Only) *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175 C for die, and below 15 C for plastic packages. See Application Information section for safe operating area information. 2. JA is measured with the component mounted on an evaluation PC board in free air. 3. The non-inverting input of unused amplifiers must be connected to GND. 4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (1% duty cycle) output current should not exceed 15mA for maximum reliability. Electrical Specifications V SUPPLY = 5V, R F = 1k A V = +1, R L = 4 C L 1pF, Unless Otherwise Specified PARAMETER TEST CONDITIONS (NOTE 9) TEST LEVEL TEMP. ( C) MIN TYP MAX UNITS INPUT CHARACTERISTICS Input Offset Voltage (V IO ) A 25 -.8 3 mv A Full - - 5 mv Delta V IO Between Channels A Full - 1.2 3.5 mv Average Input Offset Voltage Drift B Full - 5 - V/ C V IO Common Mode Rejection Ratio Note 5 A 25 53 - - db A Full 5 - - db V IO Power Supply Rejection Ratio 3.5V V S 6.5V A 25 6 - - db A Full 55 - - db Input Common Mode Range Note 5 A Full 2.5 - - V Non-Inverting Input (+IN) Current A 25-3 8 A A Full - - 2 A +IN Common Mode Rejection 1 (+I BCMR = ) +R IN Note 5 A 25 - -.15 A/V A Full - -.5 A/V +IN Power Supply Rejection 3.5V V S 6.5V A 25 - -.1 A/V A Full - -.3 A/V Inverting Input (-IN) Current A 25, 85-4 12 A A -4-1 3 A Delta -IN BIAS Current Between Channels A 25, 85-6 15 A A -4-1 3 A 2 FN3393.9 September 3, 215
HA523 Electrical Specifications V SUPPLY = 5V, R F = 1k A V = +1, R L = 4 C L 1pF, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS (NOTE 9) TEST LEVEL TEMP. ( C) MIN TYP MAX UNITS -IN Common Mode Rejection Note 5 A 25 - -.4 A/V A Full - - 1. A/V -IN Power Supply Rejection 3.5V V S 6.5V A 25 - -.2 A/V A Full - -.5 A/V Input Noise Voltage f = 1kHz B 25-4.5 - nv/ Hz +Input Noise Current f = 1kHz B 25-2.5 - pa/ Hz -Input Noise Current f = 1kHz B 25-25. - pa/ Hz TRANSFER CHARACTERISTICS Transimpedence Note 11 A 25 1. - - M A Full.85 - - M Open Loop DC Voltage Gain R L = 4, V OUT = 2.5V A 25 7 - - db A Full 65 - - db Open Loop DC Voltage Gain R L = 1, V OUT = 2.5V A 25 5 - - db A Full 45 - - db OUTPUT CHARACTERISTICS Output Voltage Swing R L = 15 A 25 2.5 3. - V A Full 2.5 3. - V Output Current R L = 15 B Full 16.6 2. - ma Output Current, Short Circuit V IN = 2.5V, V OUT = V A Full 4 6 - ma POWER SUPPLY CHARACTERISTICS Supply Voltage Range A 25 5-15 V Quiescent Supply Current A Full - 7.5 1 ma/op Amp AC CHARACTERISTICS (A V = +1) Slew Rate Note 6 B 25 275 35 - V/ s Full Power Bandwidth Note 7 B 25 22 28 - MHz Rise Time Note 8 B 25-6 - ns Fall Time Note 8 B 25-6 - ns Propagation Delay Note 8 B 25-6 - ns Overshoot B 25-4.5 - % -3dB Bandwidth V OUT = 1mV B 25-125 - MHz Settling Time to 1% 2V Output Step B 25-5 - ns Settling Time to.25% 2V Output Step B 25-75 - ns 3 FN3393.9 September 3, 215
HA523 Electrical Specifications V SUPPLY = 5V, R F = 1k A V = +1, R L = 4 C L 1pF, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS (NOTE 9) TEST LEVEL TEMP. ( C) MIN TYP MAX UNITS AC CHARACTERISTICS (A V = +2, R F = 681 Slew Rate Note 6 B 25-475 - V/ s Full Power Bandwidth Note 7 B 25-26 - MHz Rise Time Note 8 B 25-6 - ns Fall Time Note 8 B 25-6 - ns Propagation Delay Note 8 B 25-6 - ns Overshoot B 25-12 - % -3dB Bandwidth V OUT = 1mV B 25-95 - MHz Settling Time to 1% 2V Output Step B 25-5 - ns Settling Time to.25% 2V Output Step B 25-1 - ns Gain Flatness 5MHz B 25 -.2 - db 2MHz B 25 -.7 - db AC CHARACTERISTICS (A V = +1, R F = 383 ) Slew Rate Note 6 B 25 35 475 - V/ s Full Power Bandwidth Note 7 B 25 28 38 - MHz Rise Time Note 8 B 25-8 - ns Fall Time Note 8 B 25-9 - ns Propagation Delay Note 8 B 25-9 - ns Overshoot B 25-1.8 - % -3dB Bandwidth V OUT = 1mV B 25-65 - MHz Settling Time to 1% 2V Output Step B 25-75 - ns Settling Time to.1% 2V Output Step B 25-13 - ns VIDEO CHARACTERISTICS Differential Gain (Note 1) R L = 15 B 25 -.3 - % Differential Phase (Note 1) R L = 15 B 25 -.3 - NOTES: 5. V CM = 2.5V. At -4 C Product is tested at V CM = 2.25V because Short Test Duration does not allow self heating. 6. V OUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points. Slew Rate 7. FPBW = ----------------------------; V. 2 V PEAK = 2V PEAK 8. R L = 1, V OUT = 1V. Measured from 1% to 9% points for rise/fall times; from 5% points of input and output for propagation delay. 9. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only. 1. Measured with a VM7A video tester using an NTC-7 composite VITS. 11. V OUT = 2.5V. At -4 C Product is tested at V OUT = 2.25V because Short Test Duration does not allow self heating. 4 FN3393.9 September 3, 215
HA523 Test Circuits and Waveforms + - DUT 5 HP4195 NETWORK ANALYZER 5 FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS V IN (NOTE 12) 1 5 + - DUT R F, 1k R L 1 V OUT V IN (NOTE 12) 1 5 R I 681 + - DUT R F, 681 R L 4 V OUT FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT NOTE: 12. A series input resistor of 1 is recommended to limit input currents in case input signals are present before the HA523 is powered up. Vertical Scale: V IN = 1mV/Div., V OUT = 1mV/Div. Horizontal Scale: 2ns/Div. Vertical Scale: V IN = 1V/Div., V OUT = 1V/Div. Horizontal Scale: 5ns/Div. FIGURE 4. SMALL SIGNAL RESPONSE FIGURE 5. LARGE SIGNAL RESPONSE 5 FN3393.9 September 3, 215
Schematic Diagram (One Amplifier of Two) V+ R 2 8 R 5 2.5K R 1 82 Q P8 Q P9 Q P11 R 15 4 R 19 4 Q P14 R 27 2 Q P19 R 29 9.5 6 FN3393.9 September 3, 215 V- R 1 6K D 1 Q P1 Q N3 Q N1 R 3 6K Q N2 R 4 8 Q N4 R 33 8 Q P2 Q N5 Q N6 Q P4 Q N7 R 9 82 Q P7 Q P5 Q N8 Q P6 Q N9 R 12 28 R 13 1K +IN R 11 1K Q N1 Q N11 Q P1 R 14 28 Q N14 Q N12 Q P12 Q N13 R 16 4 R 17 28 -IN R 22 28 R 18 28 Q P15 C 1 1.4pF Q P13 C 2 1.4pF Q N16 R 25 14 R 24 14 R 2 14 Q N15 R 21 14 R 23 4 Q P16 Q N17 R 25 2 Q N18 R 26 2 R 28 2 Q P17 Q N19 R 31 5 Q P2 R 3 7 Q N21 R 32 5 OUT HA523
HA523 Application Information Optimum Feedback Resistor The plots of inverting and non-inverting frequency response, see Figure 8 and Figure 9 in the typical performance section, illustrate the performance of the HA523 in various closed loop gain configurations. Although the bandwidth dependency on closed loop gain isn t as severe as that of a voltage feedback amplifier, there can be an appreciable decrease in bandwidth at higher gains. This decrease may be minimized by taking advantage of the current feedback amplifier s unique relationship between bandwidth and R F. All current feedback amplifiers require a feedback resistor, even for unity gain applications, and R F, in conjunction with the internal compensation capacitor, sets the dominant pole of the frequency response. Thus, the amplifier s bandwidth is inversely proportional to R F. The HA523 design is optimized for a 1 R F at a gain of +1. Decreasing R F in a unity gain application decreases stability, resulting in excessive peaking and overshoot. At higher gains the amplifier is more stable, so R F can be decreased in a tradeoff of stability for bandwidth. The table below lists recommended R F values for various gains, and the expected bandwidth. GAIN (A CL ) R F ( ) PC Board Layout BANDWIDTH (MHz) -1 75 1 +1 1 125 +2 681 95 +5 1 52 +1 383 65-1 75 22 The frequency response of this amplifier depends greatly on the amount of care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended. If leaded components are used the leads must be kept short especially for the power supply decoupling components and those components connected to the inverting input. Attention must be given to decoupling the power supplies. A large value (1 F) tantalum or electrolytic capacitor in parallel with a small value (.1 F) chip capacitor works well in most cases. A ground plane is strongly recommended to control noise. Care must also be taken to minimize the capacitance to ground seen by the amplifier s inverting input (-IN). The larger this capacitance, the worse the gain peaking, resulting in pulse overshoot and possible instability. It is recommended that the ground plane be removed under traces connected to -IN, and that connections to -IN be kept as short as possible to minimize the capacitance from this node to ground. Driving Capacitive Loads Capacitive loads will degrade the amplifier s phase margin resulting in frequency response peaking and possible oscillations. In most cases the oscillation can be avoided by placing an isolation resistor (R) in series with the output as shown in Figure 6. V IN 1 R T R I The selection criteria for the isolation resistor is highly dependent on the load, but 27 has been determined to be a good starting value. Power Dissipation Considerations + - V OUT FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION RESISTOR, R Due to the high supply current inherent in dual amplifiers, care must be taken to insure that the maximum junction temperature (T J, see Absolute Maximum Ratings) is not exceeded. Figure 7 shows the maximum ambient temperature versus supply voltage for the available package styles (Plastic DIP, SOIC). At 5V DC quiescent operation both package styles may be operated over the full industrial range of -4 C to 85 C. It is recommended that thermal calculations, which take into account output power, be performed by the designer. MAX AMBIENT 14 13 12 11 1 9 8 7 6 5 SOIC R F R 5 7 9 11 13 15 SUPPLY VOLTAGE ( V) C L PDIP FIGURE 7. MAXIMUM OPERATING AMBIENT TEMPERATURE vs SUPPLY VOLTAGE 7 FN3393.9 September 3, 215
HA523 Typical Performance Curves V SUPPLY = 5V, A V = +1, R F = 1k R L = 4 T A = 25 C, Unless Otherwise Specified NORMALIZED GAIN (db) 5 4 3 2 1-1 -2-3 -4 V OUT =.2V P-P C L = 1pF A V = 2, R F = 681 A V = 5, R F = 1k A V = 1, R F = 383 A V = +1, R F = 1k -5 2 1 1 2 FIGURE 8. NON-INVERTING FREQENCY RESPONSE NORMALIZED GAIN (db) 5 4 3 2 1-1 -2-3 -4 V OUT =.2V P-P C L = 1pF R F = 75 A V = -1 A V = -1 A V = -5-5 2 1 1 2 FIGURE 9. INVERTING FREQUENCY RESPONSE A V = -2 NONINVERTING PHASE ( ) -45-9 -135-1 -225-27 -315-36 A V = -1, R F = 75 V OUT =.2V P-P C L = 1pF A V = +1, R F = 383 A V = -1, R F = 75 2 1 1 2 A V = +1, R F = 1k 18 135 9 45-45 -9-135 -18 INVERTING PHASE ( ) -3dB BANDWIDTH (MHz) 14 V OUT =.2V P-P C L = 1pF A V = +1 13 12-3dB BANDWIDTH 1 5 GAIN PEAKING 5 7 9 11 13 15 FEEDBACK RESISTOR ( ) GAIN PEAKING (db) FIGURE 1. PHASE RESPONSE AS A FUNCTION OF FREQUENCY FIGURE 11. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE -3dB BANDWIDTH (MHz) 1 95 9-3dB BANDWIDTH V OUT =.2V P-P C L = 1pF A V = +2 GAIN PEAKING 35 5 65 8 95 11 FEEDBACK RESISTOR ( ) 1 5 GAIN PEAKING (db) -3dB BANDWIDTH (MHz) 13 12-3dB BANDWIDTH 11 6 1 4 9 V OUT =.2V 2 GAIN PEAKING P-P C L = 1pF A V = +1 8 2 4 6 8 1 LOAD RESISTOR ( ) GAIN PEAKING (db) FIGURE 12. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE FIGURE 13. BANDWIDTH AND GAIN PEAKING vs LOAD RESISTANCE 8 FN3393.9 September 3, 215
HA523 Typical Performance Curves V SUPPLY = 5V, A V = +1, R F = 1k R L = 4 T A = 25 C, Unless Otherwise Specified (Continued) -3dB BANDWIDTH (MHz) 8 6 4 2 V OUT =.2V P-P C L = 1pF A V = +1 OVERSHOOT (%) 16 12 6 V OUT =.1V P-P C L = 1pF V SUPPLY = 5V, A V = +2 V SUPPLY = 5V, A V = +1 V SUPPLY = 15V, A V = +2 2 35 5 65 8 95 FEEDBACK RESISTOR ( ) V SUPPLY = 15V, A V = +1 2 4 6 8 1 LOAD RESISTANCE ( ) FIGURE 14. BANDWIDTH vs FEEDBACK RESISTANCE FIGURE 15. SMALL SIGNAL OVERSHOOT vs LOAD RESISTANCE.1 FREQUENCY = 3.58MHz.8 FREQUENCY = 3.58MHz DIFFERENTIAL GAIN (%).8 R L = 75.6 R L = 15.4.2 R L = 1k. 3 5 7 9 11 13 15 SUPPLY VOLTAGE ( V) DIFFERENTIAL PHASE ( ).6.4.2 R L = 15 R L = 1k R L = 75. 3 5 7 9 11 13 15 SUPPLY VOLTAGE ( V) FIGURE 16. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE FIGURE 17. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE DISTORTION (dbc) -4-5 -6-7 -8 V OUT = 2.V P-P C L = 3pF HD2 3RD ORDER IMD HD 2 HD 3 REJECTION RATIO (db) -1-2 -3-4 -5-6 -7 A V = +1 CMRR NEGATIVE PSRR HD 3-8 POSITIVE PSRR -9.3 1 1 FIGURE 18. DISTORTION vs FREQUENCY.1.1.1 1 1 3 FIGURE 19. REJECTION RATIOS vs FREQUENCY 9 FN3393.9 September 3, 215
HA523 Typical Performance Curves V SUPPLY = 5V, A V = +1, R F = 1k R L = 4 T A = 25 C, Unless Otherwise Specified (Continued) PROPAGATION DELAY (ns) 8. 7.5 7. 6.5 R L = 1 V OUT = 1.V P-P A V = +1 PROPAGATION DELAY (ns) 12 1 8 6 R LOAD = 1 V OUT = 1.V P-P A V = +1, R F = 1k A V = +1, R F = 383 A V = +2, R F = 681 6. -5-25 25 5 75 1 125 TEMPERATURE (C) 4 3 5 7 9 11 13 15 SUPPLY VOLTAGE ( V) FIGURE 2. PROPAGATION DELAY vs TEMPERATURE FIGURE 21. PROPAGATION DELAY vs SUPPLY VOLTAGE SLEW RATE (V/ s) 5 45 4 35 3 25 2 15 1 V OUT = 2V P-P + SLEW RATE - SLEW RATE -5-25 25 5 75 1 125 NORMALIZED GAIN (db).8.6.4.2 -.2 -.4 -.6 -.8 V OUT =.2V P-P C L = 1pF A V = +1, R F = 1k A V = +2, R F = 681 A V = +5, R F = 1k -1. A V = +1, R F = 383-1.2 5 1 15 2 25 3 FIGURE 22. FIGURE 22. SLEW RATE vs TEMPERATURE FIGURE 23. NON-INVERTING GAIN FLATNESS vs FREQUENCY NORMALIZED GAIN (db).8.6.4 V OUT =.2V P-P C L = 1pF R F = 75.2 A V = -1 -.2 -.4 -.6 A V = -5 -.8-1. -1.2 A V = -1 A V = -2 5 1 15 2 25 3 VOLTAGE NOISE (nv/ Hz) 1 8 6 4 2 1 A V = +1, R F = 383 -INPUT NOISE CURRENT +INPUT NOISE CURRENT INPUT NOISE VOLTAGE.1.1 1 1 1 FREQUENCY (khz) 8 6 4 2 CURRENT NOISE (pa/ Hz) FIGURE 24. INVERTING GAIN FLATNESS vs FREQUENCY FIGURE 25. INPUT NOISE CHARACTERISTICS 1 FN3393.9 September 3, 215
HA523 Typical Performance Curves V SUPPLY = 5V, A V = +1, R F = 1k R L = 4 T A = 25 C, Unless Otherwise Specified (Continued) 1.5 2 V IO (mv) 1..5 BIAS CURRENT ( A) -2. -6-4 -2 2 4 6 8 1 12 14-4 -6-4 -2 2 4 6 8 1 12 14 FIGURE 26. INPUT OFFSET VOLTAGE vs TEMPERATURE FIGURE 27. +INPUT BIAS CURRENT vs TEMPERATURE 22 4 BIAS CURRENT ( A) 2 18 TRANSIMPEDANCE (k ) 3 2 16-6 -4-2 2 4 6 8 1 12 14 1-6 -4-2 2 4 6 8 1 12 14 FIGURE 28. -INPUT BIAS CURRENT vs TEMPERATURE FIGURE 29. TRANSIMPEDANCE vs TEMPERATURE 25 74 I CC (ma) 2 15 1 55 C 125 C REJECTION RATIO (db) 72 7 68 66 64 62 +PSRR -PSRR 25 C 6 CMRR 5 3 4 5 6 7 8 9 1 11 12 13 14 15 SUPPLY VOLTAGE ( V) 58-1 -5 5 1 15 2 25 FIGURE 3. SUPPLY CURRENT vs SUPPLY VOLTAGE FIGURE 31. REJECTION RATIO vs TEMPERATURE 11 FN3393.9 September 3, 215
HA523 Typical Performance Curves V SUPPLY = 5V, A V = +1, R F = 1k R L = 4 T A = 25 C, Unless Otherwise Specified (Continued) 4 4. SUPPLY CURRENT (ma) 3 2 1 +5V +1V +15V OUTPUT SWING (V) 3.8 1 2 3 4 5 6 7 8 9 1 11 12 13 14 15 DISABLE INPUT VOLTAGE (V) FIGURE 32. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE 3.6-6 -4-2 2 4 6 8 1 12 14 FIGURE 33. OUTPUT SWING vs TEMPERATURE 3 1.2 2 V CC = 15V 1.1 V OUT (V P-P ) 1 V CC = 1V V IO (mv) 1..9 V CC = 4.5V.1.1 1. 1. LOAD RESISTANCE (k ) FIGURE 34. OUTPUT SWING vs LOAD RESISTANCE.8-6 -4-2 2 4 6 8 1 12 14 FIGURE 35. INPUT OFFSET VOLTAGE CHANGE BETWEEN CHANNELS vs TEMPERATURE 1.5-3 -4 A V = +1 V OUT = 2V P-P BIAS CURRENT ( A) 1..5 SEPARATION (db) -5-6 -7. -6-4 -2 2 4 6 8 1 12 14-8.1 1 1 3 FIGURE 36. INPUT BIAS CURRENT CHANGE BETWEEN CHANNELS vs TEMPERATURE FIGURE 37. CHANNEL SEPARATION vs FREQUENCY 12 FN3393.9 September 3, 215
HA523 Typical Performance Curves V SUPPLY = 5V, A V = +1, R F = 1k R L = 4 T A = 25 C, Unless Otherwise Specified (Continued) FEEDTHROUGH (db) -1-2 -3-4 -5-6 -7-8 DISABLE = V V IN = 5V P-P R F = 75.1 1 1 2 FIGURE 38. DISABLE FEEDTHROUGH vs FREQUENCY TRANSIMPEDANCE (M ) 1 1 R L = 1.1.1 18.1 135 9 45-45 -9-135.1.1.1 1 1 1 FIGURE 39. TRANSIMPEDANCE vs FREQUENCY PHASE ANGLE ( ) TRANSIMPEDANCE (M ) 1 1 R L = 4.1.1.1.1.1.1 1 1 1 18 135 9 45-45 -9-135 PHASE ANGLE ( ) FIGURE 4. TRANSIMPEDENCE vs FREQUENCY 13 FN3393.9 September 3, 215
HA523 Die Characteristics DIE DIMENSIONS: 165 m x 254 m x 483 m METALLIZATION: Type: Metal 1: AlCu (1%) Thickness: Metal 1: 8kÅ.4kÅ Type: Metal 2: AlCu (1%) Thickness: Metal 2: 16kÅ.8kÅ SUBSTRATE POTENTIAL (Powered Up): V- PASSIVATION: Type: Nitride Thickness: 4kÅ.4kÅ TRANSISTOR COUNT: 124 PROCESS: High Frequency Bipolar Dielectric Isolation Metallization Mask Layout HA523 OUT NC V+ -IN1 +IN1 NC OUT2 NC V- +IN -IN 14 FN3393.9 September 3, 215
Revision History HA523 The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION CHANGE September 3, 215 FN3393.9 - Updated Ordering Information Table on page 1. - Added Revision History. - Added About Intersil Verbiage. - Updated POD M8.15 to latest revision changes are as follow: -Revision 1 to Revision 2 Changes: Updated to new POD format by removing table and moving dimensions onto drawing and adding land pattern -Revision 2 to Revision 3 Changes: Changed in Typical Recommended Land Pattern the following: 2.41(.95) to 2.2(.87).76 (.3) to.6(.23).2 to 5.2(.25) -Revision 3 to Revision 4 Changes: Changed Note 1 "1982" to "1994" About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO91 quality systems. Intersil Corporation s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 FN3393.9 September 3, 215
HA523 Dual-In-Line Plastic Packages (PDIP) INDEX AREA BASE PLANE SEATING PLANE D1 B1 -C- -A- N 1 2 3 N/2 B D e D1 E1 -B- A 1.1 (.25) M C A A2 L B S NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the MO Series Symbol List in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed.1 inch (.25mm). 6. E and e A are measured with the leads constrained to be perpendicular to datum -C-. 7. e B and e C are measured at the lead tips with the leads unconstrained. e C must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed.1 inch (.25mm). 9. N is the maximum number of terminal positions. 1. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of.3 -.45 inch (.76-1.14mm). A e C E C L e A C e B E8.3 (JEDEC MS-1-BA ISSUE D) 8 LEAD DUAL-IN-LINE PLASTIC PACKAGE INCHES MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A -.21-5.33 4 A1.15 -.39-4 A2.115.195 2.93 4.95 - B.14.22.356.558 - B1.45.7 1.15 1.77 8, 1 C.8.14.24.355 - D.355.4 9.1 1.16 5 D1.5 -.13-5 E.3.325 7.62 8.25 6 E1.24.28 6.1 7.11 5 e.1 BSC 2.54 BSC - e A.3 BSC 7.62 BSC 6 e B -.43-1.92 7 L.115.15 2.93 3.81 4 N 8 8 9 Rev. 12/93 16 FN3393.9 September 3, 215
HA523 Package Outline Drawing M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 4, 1/12 DETAIL "A" 1.27 (.5).4 (.16) INDEX AREA 4. (.157) 3.8 (.15) 6.2 (.244) 5.8 (.228).5 (.2).25 (.1) x 45 1 2 3 TOP VIEW 8 SIDE VIEW B.25 (.1).19 (.8) 2.2 (.87) SEATING PLANE 1 8 5. (.197) 4.8 (.189) 1.75 (.69) 1.35 (.53) 2 7.6 (.23) 1.27 (.5) 3 6 -C- 1.27 (.5).51(.2).33(.13).25(.1).1(.4) 4 5 5.2(.25) SIDE VIEW A TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensioning and tolerancing per ANSI Y14.5M-1994. 2. Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed.15mm (.6 inch) per side. 3. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed.25mm (.1 inch) per side. 4. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 5. Terminal numbers are shown for reference only. 6. The lead width as measured.36mm (.14 inch) or greater above the seating plane, shall not exceed a maximum value of.61mm (.24 inch). 7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 8. This outline conforms to JEDEC publication MS-12-AA ISSUE C. 17 FN3393.9 September 3, 215