KATHREIN SE P.O. Box 10 04 44 83004 Rosenheim Germany KATHREIN-erke KG ist jetzt KATHREIN SE KATHREIN-erke KG is now KATHREIN SE Rosenheim, 01.05.2018 KATHREIN SE Anton-Kathrein-Straße 1 3 83022 Rosenheim Germany Phone: +49 8031 184-0 Fax: +49 8031 184-306 Zum 1. Mai 2018 ist die KATHREIN-erke KG auf die KATHREIN SE, einer Europäischen Aktiengesellschaft (Societas Europaea), übergegangen. Die neuen Firmendaten lauten seither wie folgt: KATHREIN SE Anton-Kathrein-Str. 1 3 83022 Rosenheim, Deutschland Steuer-Nr.: 156/117/30745 UST-Ident-Nr.: DE 131 558 540 Registergericht: Traunstein, HRB 24848 On 1 st May 2018, KATHREIN-erke KG has been transferred to KATHREIN SE, a European stock corporation (Societas Europaea). Executive Board: Anton Kathrein (CEO), Joachim Döring, Elmar Geißinger, Jürgen alter, Hans-Joachim Ziems Supervisory Board: Dr. Michael F. Keppel (Chairman) VAT Reg. No.: DE 131 558 540 Tax ID No.: 156/117/30745 EEE Reg. No.: DE 38438502 GLN: 40 21121 00000 3 Registered Office: Rosenheim, DE Commercial Register: Traunstein, HRB 24848 Deutsche Bank AG IBAN: DE54 7007 0010 0833 7701 00 BIC: DEUTDEMMXXX Since then the company data is as follows: KATHREIN SE Anton-Kathrein-Str. 1 3 83022 Rosenheim, Deutschland Tax ID No.: 156/117/30745 VAT Reg. No.: DE 131 558 540 Commercial Register: Traunstein, HRB 24848 936.0000218a Page 1 of 1
4-Port Dual-Beam Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT Azimuth Beam Direction Optimized Horizontal Sidelobes 4-Port Dual-Beam Antenna 1710 2200/1710 2200 45 (+30 )/45 ( 30 ) 19.5/19.5dBi 0 10 /0 10 T Type No. 80010606V01 Left side, highband B1, connector 1 2 1710 2200 Frequency Range MHz 1710 1880 1850 1990 1920 2200 Gain at mid Tilt dbi 19.0 19.1 19.4 Gain over all Tilts dbi 18.9 ± 0.2 19.0 ± 0.2 19.2 ± 0.4 Horizontal Pattern: Azimuth Beamwidth 47 ± 1.1 46 ± 1.1 44 ± 2.7 Front-to-Back Ratio, Total Power, ± 30 db > 26 > 27 > 26 Cross Polar Discrimination over Sector db > 9.0 > 8.5 > 10.5 Azimuth Beam Squint 0.5 ± 1.2 0.0 ± 1.2 0.0 ± 0.9 Azimuth Beam Port-to-Port Tracking db < 1.0 < 1.5 < 1.5 Vertical Pattern: Elevation Beamwidth 7.2 ± 0.1 7.0 ± 0.1 6.7 ± 0.4 Electrical Downtilt continuously adjustable 0.0 10.0 Tilt Accuracy < 0.5 < 0.5 < 0.4 First Upper Side Lobe Suppression db > 19 > 22 > 19 B1 1710 2200 1710 2200 18dB 18dB Downtilt set by hand or by optional RCU (Remote Control Unit) Cross Polar Isolation db > 30 Port to Port Isolation db > 30 (B1 // B2) per Port 200 (at 50 C ambient temperature) Port 1 2 400 (at 50 C ambient temperature) Values based on NGMN-P-BASTA (version 9.6) requirements. X 45 0 10 (+30 ) B2 X 45 0 10 ( 30 ) 80010606V01 Page 1 of 5
4-Port Dual-Beam Antenna Right side, highband B2, connector 3 4 1710 2200 Frequency Range MHz 1710 1880 1850 1990 1920 2200 Gain at mid Tilt dbi 19.0 19.1 19.4 Gain over all Tilts dbi 18.9 ± 0.2 19.0 ± 0.2 19.2 ± 0.4 Horizontal Pattern: Azimuth Beamwidth 48 ± 1.6 47 ± 1.5 44 ± 2.6 Front-to-Back Ratio, Total Power, ± 30 db > 28 > 26 > 26 Cross Polar Discrimination over Sector db > 9.0 > 9.5 > 10.0 Azimuth Beam Squint 0.0 ± 1.4 0.5 ± 1.2 1.0 ± 0.8 Azimuth Beam Port-to-Port Tracking db < 2.0 < 2.0 < 2.5 Vertical Pattern: Elevation Beamwidth 7.2 ± 0.1 7.0 ± 0.1 6.7 ± 0.4 Electrical Downtilt continuously adjustable 0.0 10.0 Tilt Accuracy < 0.5 < 0.4 < 0.4 First Upper Side Lobe Suppression db > 18 > 22 > 20 Cross Polar Isolation db > 30 Port to Port Isolation db > 30 (B1 // B2) per Port 200 (at 50 C ambient temperature) Port 3 4 400 (at 50 C ambient temperature) Values based on NGMN-P-BASTA (version 9.6) requirements. Page 2 of 5 80010606V01
4-Port Dual-Beam Antenna Electrical specifications, all systems Impedance Ω 50 VSR < 1.5 Return Loss db > 14 Interband Isolation db > 30 Passive Intermodulation dbc < 150 (2 x 43 dbm carrier) Polarization +45, 45 800 (at 50 C ambient for the Antenna temperature) Values based on NGMN-P-BASTA (version 9.6) requirements. Mechanical specifications Input Connector Position Adjustment Mechanism 4 x 7-16 female bottom 2x, Position bottom continuously adjustable ind load (at Rated N lbf Frontal: 385 87 ind Speed: 150 km/h) Maximal: 420 94 Max. ind Velocity Height / idth / Depth Category of Mounting Hardware eight Packing Size Scope of Supply km/h mph mm inches kg lb mm inches 200 124 1314 / 381 / 151 51.7 / 15.0 / 5.9 M (Medium) 19.0 / 21.2 (clamps incl.) 41.9 / 46.7 (clamps incl.) 1696 / 402 / 172 66.8 / 15.8 / 6.8 Panel and 2 units of clamps for 42 115 mm 1.7 4.5 inches diameter Accessories (order separately if required) Type No. Description Remarks mm inches eight approx. kg lb Units per antenna 1) 2) 1) 9 0.4 2) 64 2.5 731651 1 clamp Mast diameter: 28 60 1.1 2.4 0.8 1.8 2 85010002 1 clamp Mast diameter: 110 220 4.3 8.7 2.7 6.0 2 85010003 1 clamp Mast diameter: 210 380 8.3 15.0 4.8 10.6 2 Accessories (included in the scope of supply) 738546 1 clamp Mast diameter: 42 115 1.7 4.5 1.1 2.4 2 For wall mounting: Azimuth Adjustment Kit 85010016. For 3 Panel Arrangement: 3 Sector Clamp Kit 742034. Please note: The dual-beam antenna must not be used in combination with any downtilt kit. Material: Grounding: Reflector screen: Tin-plated copper. Radiator: Tin-plated zinc. Fiberglass radome: The grey fiberglass radomes of these antennas are very stable and extraordinarily stiff. They are resistant to ultraviolet radiation and can also be painted to match their surroundings. All screws and nuts: Stainless steel. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. Adjustment mechanism with integrated scale 1314 51.7 1484 58.4 1514 59.6 All dimensions in mm inches 80010606V01 Page 3 of 5
4-Port Dual-Beam Antenna Layout of interface: 120 4.7 50 2.0 57 2.2 135 5.3 151 5.9 381 15.0 Bottom view All dimensions in mm inches Correlation Table Frequency range Array Connector 1710 2200 MHz B1 1 2 1710 2200 MHz B2 3 4 B1 B2 Left Right Page 4 of 5 80010606V01
Proposal for 6 Sector Deployment Example of 6 Sectors by using 3x 80010606V01 and 3 Sector Clamp Kit 742034 Antenna I Right 330 0 0 30 Antenna I Left 3 300 6 60 10 20 270 90 Antenna II Left Antenna III Right 240 120 Antenna II Right 210 150 180 Horizontal Patterns (top view) Antenna III Left Antenna I D out 470 mm Antenna III Antenna II Bottom view For the above 3 Panel Arrangement please use the 3 Sector Clamp Kit 742034 (order separately). 3 Panel Arrangement with 3x 80010606V01 Mechanical specifications eight ind load (at Rated ind Speed: 150 km/h) Max. ind Velocity kg lb 60 132.3 N lbf Frontal: 950 214 Maximal: 950 214 km/h mph 200 124 Any previous data sheet issues have now become invalid. 80010606V01 Page 5 of 5
Mounting Hardware Clamp Included in the Scope of Supply Suitable for mast diameter Antenna mast distance Material of clamp and screws eight mm inches mm inches kg lb 42 115 1.65 4.53 20 25 0.79 0.98 Hot-dip galvanized steel / stainless steel 1.1 2.43 152 5.98 100 3.94 72 2.8 20 25 0.79 0.98 40 1.57 936.3920e Subject to alteration. 40 1.57 42 115 1.65 4.53 M10 M A = 25 Nm 35 1.38 M8 M A = 12 Nm 64 2.52 125 4.92 20 25 0.79 0.98 Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares. All dimensions in mm inches Any previous data sheet issues have now become invalid. 738546 Page 1 of 1 KATHREIN SE Anton-Kathrein-Straße 1 3 83022 Rosenheim, Germany Phone +49 8031 184-0 mobilcom@kathrein.de
General Instructions for Adjustment Mechanism Description of the adjustment mechanism (protective cap removed): 1 1 2 2 Twist protection. Downtilt spindle with integrated scale. Thread for fixing the pro tective cap or the RCU (Remote Control Unit). Gearwheel for RCU power drive. To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: 0 max. 0 max. Remove the protective cap and the twist protection completely. Set downtilt angle by rotating the gearwheel. Screw on the twist protection and the protective cap again. Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment: 936.4037b Subject to alteration. For a description of RCU installation please refer to the respective data sheet. Page 1 of 2 KATHREIN SE Anton-Kathrein-Straße 1 3 83022 Rosenheim, Germany Phone +49 8031 184-0 mobilcom@kathrein.de
General Instructions for Feederline and RCU Installation for Antennas Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width. Description of bottom end cap (exemplary picture): Adjustment mechanism (protective cap removed) Ventilation hole Spindle with tilting scale 7-16 female (long neck) Colour coding: Correlation of each RF input to: the corresponding adjustment mechanism the frequency range the polarization Installation of the feederline connector and RCU (optional): In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation! Kathrein installation set: Type No. 85010077 Set has to be ordered separately! Set consists of three spanners of divers width 27, 32 and 41 mm 1.1, 1.3 and 1.6 inches 1/2 square actuation according to DIN 3120 Form C 32 1.3 Carefully place the connector and fix the nut using a torque-wrench (according to the manufacturers guidelines). After feederline installation, the optional remote control units (RCUs) can be mounted. 27 1.1 All dimensions in mm inches 41 1.6 These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm 1.6 inches. 936.4037b Subject to alteration. Tighten nuts within a torque range of 25 33 Nm depending on connector manufacturers specifications, respectively the RCU nut with a torque range of 15 18 Nm. Page 2 of 2 Any previous data sheet issues have now become invalid. KATHREIN SE Anton-Kathrein-Straße 1 3 83022 Rosenheim, Germany Phone +49 8031 184-0 mobilcom@kathrein.de