HA511 1MHz, Low Noise, Operational Amplifiers OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA2525, HA282 DATASHEET FN295 Rev 5. May 2 The HA511 is a dielectrically isolated operational amplifier featuring low noise, (.nv/ Hz at 1kHz). DC characteristics of the HA511 assure accurate performance. The.5mV offset voltage is externally adjustable and offset voltage drift is just V/ o C. An offset current of only na reduces input current errors and an open loop voltage gain of 1 x 1 6 V/V increases loop gain for low distortion amplification. The HA511 is ideal for audio applications, especially lowlevel signal amplifiers such as microphone, tape head and phono cartridge preamplifiers. Additionally, it is well suited for low distortion oscillators, low noise function generators and high Q filters. Pinout IN IN V 1 2 HA511(SOIC) TOP VIEW 8 COMP 7 6 5 V OUT Features Low Noise......................nV/ Hz at 1kHz Bandwidth............................... 1MHz Slew Rate................................ 1V/ s Low Offset Voltage Drift.................... V/ o C High Gain............................. 1 x 1 6 V/V High CMRR/PSRR......................... 1dB High Output Drive Capability.................. ma Applications High Quality Audio Preamplifiers High Q Active Filters Low Noise Function Generators Low Distortion Oscillators Low Noise Comparators For Further Design Ideas, See Application Note AN55 Part Number Information PART NUMBER (BRAND) HA9P5119 (H5119) TEMP. RANGE ( o C) PACKAGE PKG. NO. to 85 8 Ld SOIC M8.15 FN295 Rev 5. Page 1 of 1 May 2
HA511 Schematic IN IN V R 2 R 25 R 2 Q 2 R 26 Q 26 Q 7 R 6 R 28 Q 2 Q 28 R 5 Q 25 QL1 Q 5 Q L1 R Q L2 Q 1 Q15 Q 16 R 7 Q 7 Q 5 R 6 Q 6 R 22 Q 1 Q Q 1A Q 1B Q 29 Q 6 Q Q 1 Q 2 Q Q 8 Q Q 2B Q 2A Q 2 Q 1 R 15 OUTPUT R 17A Q 21 Q 17 R 2 Q 19B C 1 Q 2 Q 19A Q 11 Q 1 Q 27 Q 5 Q Q 9 Q Q 6 Q 7 C 2 Q 12 Q R 58 Q 8 Q 18 R A R A Q 9 Q 5 Q 9 Q 8 R 19A R 11 R 1 R 12 R27 R B R B Q 51 R 18 V R 19B FN295 Rev 5. Page 2 of 1 May 2
HA511 Absolute Maximum Ratings Voltage Between V and V Terminals................... V Differential Input Voltage............................... 7V Input Voltage V SUPPLY Output Current................... Full Short Circuit Protection Operating Conditions Temperature Range HA5119............................... o C to 85 o C Thermal Information Thermal Resistance (Typical, Note 2) JA ( o C/W) JC ( o C/W) SOIC Package................... 16 N/A Maximum Junction Temperature (Note 1).............. 15 o C Maximum Storage Temperature Range......... 65 o C to 15 o C Maximum Lead Temperature (Soldering 1s)............ o C (Lead Tips Only) CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain the maximum junction temperature below 15 o C for the plastic packages. 2. JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB79 for details. Electrical Specifications V SUPPLY = 15V, R S = 1 R L = C L = 5pF, Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP ( o C) MIN TYP MAX UNITS INPUT CHARACTERISTICS Offset Voltage 25.5 mv Full mv Offset Voltage Drift Full V/ o C Bias Current 25 1 2 na Full 25 na Offset Current 25 75 na Full 125 na Input Resistance 25 5 k Common Mode Range Full 12 V TRANSFER CHARACTERISTICS Large Signal Voltage Gain V OUT = 1V 25 1 kv/v Full 1 25 kv/v Common Mode Rejection Ratio V CM = 1V Full 8 1 db Small Signal Bandwidth A V = 1 25 1 MHz Minimum Stable Gain Full 1 V/V OUTPUT CHARACTERISTICS Output Voltage Swing R L = 1k Full 12 1 V R L = Full 12 1 V V S = 18V, R L = 6 25 15 V Output Current (Note ) 25 25 ma Full Power Bandwidth (Note ) 25 95 16 khz Output Resistance 25 11 Maximum Load Capacitance 25 8 pf TRANSIENT RESPONSE (Note 5) Rise Time 25 5 1 ns Overshoot 25 2 5 % FN295 Rev 5. Page of 1 May 2
HA511 Electrical Specifications V SUPPLY = 15V, R S = 1 R L = C L = 5pF, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS TEMP ( o C) MIN TYP MAX UNITS Slew Rate 25 6 1 V/ s Settling Time (Note 6).1% 2.6 s NOISE CHARACTERISTICS (Note 7) Input Noise Voltage f = 1Hz 25 5 7 nv/ Hz f = 1kHz 25.. nv/ Hz Input Noise Current f = 1Hz 25. 9 pa/ Hz f = 1kHz.6 2.5 pa/ Hz Broadband Noise Voltage f = DC To khz 25.87 V RMS POWER SUPPLY CHARACTERISTICS Supply Current Full 7 ma Power Supply Rejection Ratio V S = 5V Full 8 1 db NOTES:. Output current is measured with V OUT = 15V with V SUPPLY = 18V. Slew Rate. Full power bandwidth is guaranteed by equation: Full power bandwidth =,V. 2 V PEAK = 1V 5. Refer to Test Circuits section of the data sheet. PEAK 6. Settling time is measured to.1% of final value for a 1V output step, and A V = 1. 7. The limits for these parameters are guaranteed based on lab characterization, and reflect lottolot variation. Test Circuits and Waveforms IN IN OUT 5pF OUT 1k 5pF FIGURE 1. LARGE SIGNAL RESPONSE CIRCUIT FIGURE 2. SMALL SIGNAL RESPONSE CIRCUIT FN295 Rev 5. Page of 1 May 2
HA511 Test Circuits and Waveforms (Continued) 5V 1mV V V 5V 1mV Ch. 1 = 2.5V/Div. Timebase = 1. s/div. FIGURE. LARGE SIGNAL TRANSIENT RESPONSE Ch. 1 = 5mV/Div. Timebase = 1ns/Div. FIGURE. SMALL SIGNAL TRANSIENT RESPONSE 5k (NOTE 9) 2N16 5k 15V TO OSCILLOSCOPE V IN (NOTE 9) 15V 15V 5pF V OUT NOTES: 8. A V = 1. 9. Feedback and summing resistors should be.1% matched. 1. Clipping diodes are optional, HP582281 recommended. FIGURE 5. SETTLING TIME CIRCUIT Application Information Operation At 5V Supply The HA511 performs well at V S = 5V exhibiting typical characteristics as listed below: I CC..............................7mA V IO..............................5mV I BIAS............................ 56nA A VOL (V O = V).................. 16kV/V V OUT............................7V I OUT............................ 1mA CMRR ( V CM = 2.5V)............. 9dB PSRR ( V S =.5V)................ 9dB Unity Gain Bandwidth.............. 1MHz Slew Rate........................ 7V/ s Offset Adjustment The following is the recommended V IO adjust configuration: (NOTE) 2 15V 7 1 15V RP (NOTE) NOTE: Proper decoupling is always recommended,.1 F high quality capacitor should be at or very near the device s supply pins. Input Protection The HA511 has builtin backtoback protection diodes which will limit the differential input voltage to approximately 7V. If the 5 6 R P = 1k FN295 Rev 5. Page 5 of 1 May 2
HA511 511 will be used in conditions where that voltage may be exceeded, then current limiting resistors must be used. No more than 25mA should be allowed to flow in the HA511 s input. If saturation cannot be avoided the HA511 recovers from a 25% overdrive in about 6.5 s (see photos). Comparator Circuit V IN R V LIM IN 2 7 6 VIN R LIM OUT V V Choose R LIM Such That: INMAX 7V 2R 25mA LIM Output Saturation When an op amp is overdriven, output devices can saturate and sometimes take a long time to recover. Saturation can be avoided (sometimes) by using circuits such as: Top: Input Bottom: Output, 5V/Div., 2 s/div. Output is overdriven negative and recovers in 6 s. V R 1 R 2 R V SOURCE R V Typical Performance Curves 8 15 INPUT NOISE VOLTAGE (nv/ Hz) 7 6 5 2 1 VOLTAGE CURRENT INPUT NOISE CURRENT (pa/ Hz) OFFSET VOLTAGE ( V) 1 5 1 1 1K 1K 1K FREQUENCY (Hz) 5 25 25 5 75 TEMPERATURE ( o C) 1 125 FIGURE 6. NOISE SPECTRUM FIGURE 7. OFFSET VOLTAGE vs TEMPERATURE FN295 Rev 5. Page 6 of 1 May 2
HA511 Typical Performance Curves (Continued) A V = 25 V S = 15V (2.25 V PP RTO) PEAKTOPEAK NOISE.1Hz TO 1Hz A V = 25, V S = 15V (12.89mV PP RTO) PEAKTOPEAK TOTAL NOISE.1Hz TO 1MHz 2 25 INPUT OFFSET CURRENT (na) 2 BIAS CURRENT (na) 2 15 1 5 6 55 25 25 5 75 1 125 TEMPERATURE ( o C) FIGURE 8. INPUT OFFSET CURRENT vs TEMPERATURE 55 25 25 5 75 1 125 TEMPERATURE ( o C) FIGURE 9. INPUT BIAS CURRENT vs TEMPERATURE 1.1 1.1 1 SLEW RATE (NORMALIZED) 1..9.8.7 RISE TIME SLEW RATE R L =, C L = 5pF V S = 15V 1..9.8.7 RISE TIME (NORMALIZED) VOLTAGE GAIN (db) 12 1 8 6 2 PHASE GAIN 5 9 15 18 PHASE SHIFT (DEGREES).6 6 2 2 6 8 1 12 TEMPERATURE ( o C).6 1 1 1K 1K 1K FREQUENCY (Hz) 1M 1M 1M FIGURE 1. SLEW RATE/RISE TIME vs TEMPERATURE FIGURE 11. OPENLOOP GAIN/PHASE vs FREQUENCY FN295 Rev 5. Page 7 of 1 May 2
HA511 Typical Performance Curves (Continued) T A = 25 o C, V S = 15V 5 T A = 25 o C MAXIMUM 2 OFFSET CHANGE ( V) 1 1 2 SUPPLY CURRENT (ma) 2 1 TYPICAL MINIMUM 5 1 15 2 25 5 TIME (SECONDS) 5 5 2 6 8 1 12 1 SUPPLY VOLTAGE ( V) 16 18 2 FIGURE 12. INPUT OFFSET WARMUP DRIFT vs TIME (NORMALIZED TO ZERO FINAL VALUE) (SIX REPRESENTATIVE UNITS) FIGURE 1. SUPPLY CURRENT vs SUPPLY VOLTAGE V/V 1M (db) (1) OPEN LOOP VOLTAGE GAIN 1M (12) 1K (1) 1K (8) 5 1 15 18 SUPPLY VOLTAGE ( V) OUTPUT CURRENT (ma) 6 5 2 1 2 D B C A V IN V OUT A 15mV 15V B 15mV 15V C 15mV V D 15mV V 6 8 TIME (S) T A = 25 o C, V S = 15V 1 12 1 16 FIGURE 1. DC OPENLOOP VOLTAGE GAIN vs SUPPLY VOLTAGE FIGURE 15. SHORT CIRCUIT CURRENT vs TIME FN295 Rev 5. Page 8 of 1 May 2
HA511 Typical Performance Curves (Continued) 6 CLOSED LOOP VOLTAGE GAIN (db) 6 9 12 1K V s = 15V, A V = 1V/V R L =, C L = 5pF 1K 125 o C PHASE 1M FREQUENCY (Hz) 125 o C GAIN 1M 55 o C GAIN 55 o C PHASE FIGURE 16. FREQUENCY RESPONSE 5 9 15 18 225 1M PHASE SHIFT (DEGREES) V ERROR 1mV 2.65 S FIGURE 17. SETTLING WAVEFORM 1.5 s/div. A V = 1 T A = 25 o C, V s = 15V GAIN (db) 2 1 1 2 A V = 1 A V = 1 REJECTION RATIO (db) 6 8 1 PSRR/CMRR PSRR T A = 25 o C, V S = 15V R L =, C L = 5pF 1K 1K 1M FREQUENCY (Hz) 1M 1M 12 1 1K 1K 1K 1M FREQUENCY (Hz) FIGURE 18. CLOSEDLOOP GAIN vs FREQUENCY FIGURE 19. REJECTION RATIOS vs FREQUENCY V OUT (V) 1 1 12 11 1 V SUPPLY = 15V 55 o C 25 o C.2V 125 o C 1 1k V OUT R LOAD V OUT (V) 7 8 9 1 11 12 1 55 o C 25 o C.2V 1 125 o C 1k V OUT R LOAD V SUPPLY = 15V 9 1 2 R LOAD ( ) 5 6 1 1 2 R LOAD ( ) 5 6 FIGURE 2. V OUT vs R L FIGURE 21. V OUT vs R L FN295 Rev 5. Page 9 of 1 May 2
HA511 Die Characteristics SUBSTRATE POTENTIAL (Powered Up): V TRANSISTOR COUNT: 5 PROCESS: Bipolar Dielectric Isolation Metallization Mask Layout HA511 NC IN V IN OUT V Copyright Intersil Americas LLC 2. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO91 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN295 Rev 5. Page 1 of 1 May 2