FT- CAT OperATiOn reference BOOk YAESU MUSEN CO., LTD.
Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as dualchannel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated with single mouse clicks, or keystroke operations on the computer keyboard. Using the RS-C Cable (Refer to igure ) The FT- transceiver has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. When using the RS-C cable, set Menu item 0 GPS/C SELECT to RSC. You will need a serial cable for connection to the RS- C (serial or COM port) connector on your computer. Purchase a standard serial cable (not the so-called null modem type), ensuring it has the correct gender and number of pins (some serial COM port connectors use a -pin rather than -pin coniguration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. COnneCTiOn 7 6 Pin No. Pin Name I/O Function N/A --- --- SERIAL OUT Output SERIAL IN Input Outputs the Serial Data from the transceiver to the computer. Inputs the Serial Data from the computer to the transceiver. N/A --- --- GND --- Signal Ground N/A --- --- RTS --- --- CTS --- --- N/A --- --- Personal Computer Using the USB Cable (Refer to igure ) Note: A USB driver is required for remote control from a computer. Download the driver from the Yaesu website (http://www.yaesu.com). The FT- transceiver has a built-in USB to Dual UART Bridge, allowing direct connection from the rear-panel USB jack to the USB jack of your computer without the need of any external boxes. COM FT- GPS/CAT You will need a USB cable to connect to the USB jack on your computer. YAESU MUSEN does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs for your operating needs and utilize the full operating potential of this system. Personal Computer Figure RS-C Straight Cable FT- USB USB Figure USB Cable
COnTrOl COmmAnd A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: the VFO-A frequency to.0000 MHz. FA 00000 Command Parameter Terminator There are three commands for the FT- as shown below: command: a particular condition (to the FT-) command: s an answer (from the FT-) command: Transmits a condition (from the FT-) For example, note the following case of the FA command ( the VFO-A frequency): To set the VFO-A frequency to.0000 MHz, the following command is sent from the computer to the transceiver: FA00000 ( command) To read the VFO-A frequency, the following command is sent from the computer to the transceiver: FA ( command) When the command above has been sent, the following command is returned to the computer: FA00000 ( command) Alphabetical Commands A command consists of alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the PC Control Command Tables on the following pages. Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the Control Command List and the Control Command Tables to conigure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when the correct parameter is IS0+000 (IF SHIFT): IS0000 Not enough parameters speciied (No direction (+) given for the IF shift) IS0+00 Not enough digits (Only three frequency digits given) IS0_+_000 Unnecessary characters between parameters IS0+0000 Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FT-, the parameter digits should be illed using any character except the ASCII control codes (00 to Fh) and the terminator (). Terminator To signal the end of a command, it is necessary to use a semicolon (). The digit where this special character must appear differs depending on the command used.
Command Function Ans. AI AB VFO-A TO VFO-B O X X X AC ANTENNA TUNER CONTROL O O O O AG AF GAIN O O O O AI AUTO INFORMATION O O O X AM VFO-A TO MEMORY CHANNEL O X X X BA VFO-B TO VFO-A O X X X BC AUTO NOTCH O O O O BD BAND DOWN O X X X BI BREAK-IN O O O O BP MANUAL NOTCH O O O O BS BAND SELECT O X X X BU BAND UP O X X X BY BUSY X O O O CH CHANNEL UP/DOWN O X X X CN CTCSS NUMBER O O O O CO CONTOUR O O O O CS CW SPOT O O O O CT CTCSS O O O O DA DIMMER O O O X DN DOWN O X X X DT DATE AND TIME O O O X ED ENCORDER DOWN O X X X EK ENT KEY O X X X EU ENCORDER UP O X X X EX MENU O O O O FA FREQUENCY VFO-A O O O O FB FREQUENCY VFO-B O O O O FS FAST STEP O O O O FT FUNCTION TX O O O O GT AGC FUNCTION O O O O ID IDENTIFICATION X O O X IF INFORMATION X O O O IS IF-SHIFT O O O O KM KEYER MEMORY O O O X KP KEY PITCH O O O O KR KEYER O O O O KS KEY SPEED O O O O KY CW KEYING O X X X LK LOCK O O O O LM LOAD MESSEGE O O O X MA MEMORY CHANNEL TO VFO-A O X X X MC MEMORY CHANNEL O O O X MD MODE O O O O MG MIC GAIN O O O O ML MONITOR LEVEL O O O O MR MEMORY READ X O O X MS METER SW O O O O MW MEMORY WRITE O X X X MX MOX SET O O O O NA NARROW O O O O NB NOISE BLANKER O O O O NL NOISE BLANKER LEVEL O O O O NR NOISE REDUCTION O O O O OI OPPOSITE BAND NFORMATION X O O O OS OFFSET (Repeater Shift) O O O O PA PRE-AMP (IPO) O O O O PB PLAY BACK O O O X PC POWER CONTROL O O O O PL SPEECH PROCESSOR LEVEL O O O O Command Function Ans. AI PR SPEECH PROCESSOR O O O O PS POWER SWITCH O O O X QI QMB STORE O X X X QR QMB RECALL O X X X QS QUICK SPLIT O X X X RA RF ATTENUATOR O O O O RC CLAR CLEAR O X X X RD CLAR DOWN O X X X RG RF GAIN O O O O RI RADIO INFORMATION X O O O RL NOISE REDUCTION LEVEL O O O O RM READ METER X O O O RS RADIO STATUS X O O X RT CLAR O O O O RU CLAR UP O X X X SC SCAN O O O O SD SEMI BREAK-IN DELAY TIME O O O O SH WIDTH O O O O SM S METER X O O X SQ SQUELCH LEVEL O O O O SV SWAP VFO O X X X TS TXW O O O O TX TX SET O O O O UL UNLOCK X O O O UP UP O X X X VD VOX DELAY TIME O O O O VG VOX GAIN O O O O VM [V/M] KEY FUNCTION O X X X VX VOX O O O O XT TX CLAR O O O O ZI ZERO IN O X X X
AB VFO-A TO VFO-B A B AC ANTENNA TUNER CONTROL 0: Fixed P 0: Tuner OFF A C P P P 0: Fixed : Tuner ON : Tuning Start A C A C P P AG AF GAIN 0: Fixed A G P P P P 000 - A G A G P P P AI AUTO INFORMATION 0: Auto Information OFF A I : Auto Information ON A I A I This parameter is set to 0 (OFF) automatically when the transceiver is turned OFF. AM VFO-A TO MEMORY CHANNEL A M BA VFO-B TO VFO-A B A BC AUTO NOTCH 0: Fixed B C P P 0: Auto Notch OFF : Auto Notch ON B C B C P BD BAND DOWN 0: Fixed B D
BI BREAK-IN 0: Break-in OFF B I : Break-in ON B I B I BP MANUAL NOTCH 0: Fixed P P=0 B P P P P P P 0: Manual NOTCH ON/OFF 000: OFF B P P 6 6 7 7 0 0 : Manual NOTCH LEVEL 00: ON P= 00-0 (NOTCH Frequency : x 0 Hz ) B P P P P P BS BAND SELECT 00:. MHz 06: MHz : MW B S 0:. MHz 07: MHz : - 0: - 0:. MHz : AIR 0: 7 MHz 0: MHz : MHz 0: 0 MHz 0: 0 MHz 6: 0 MHz 0: MHz : GEN BU BAND UP 0: Fixed B U BY BUSY 0: RX BUSY OFF : RX BUSY ON P 0: Fixed B Y B Y P CH CHANNEL UP/DOWN 0: Memory Channel UP C H : Memory Channel DOWN CN CTCSS TONE FREQUENCY 0: Fixed C N P P P 0 - : Tone Frequency Number (See Table ) C N C N P P CO CONTOUR 0: Fixed P P=0 0000: CONTOUR OFF C O P P P P P P 0: CONTOUR ON/OFF 000: CONTOUR ON : CONTOUR FREQ P= 000-00 : APF ON/OFF (CONTOUR Frequency:0-00Hz) C O P : APF FREQ P= 0000: APF OFF 000: APF ON P= 0000-000 (APF Frequency: -0-0 Hz ) C O P P P P P
CS CW SPOT 0: OFF C S : ON C S C S CT CTCSS 0: Fixed C C T T P 6 7 0 P 0: CTCSS OFF : CTCSS ENC/DEC ON : CTCSS ENC ON : DCS ON C T P Table (CTCSS Tone Chart) 00 67.0 Hz 0. Hz.0 Hz 7 6. Hz 6. Hz. Hz 0 6. Hz 0. Hz 7. Hz 6. Hz 7. Hz 6.6 Hz 0 7. Hz 7. Hz 0. Hz 67. Hz 6.6 Hz 7. Hz 0 7. Hz 00.0 Hz 6. Hz 0 7. Hz. Hz 0. Hz 0 77.0 Hz 0. Hz. Hz 7. Hz 0 0. Hz. Hz 0 7.7 Hz 07. Hz 6. Hz 77. Hz 06. Hz - - 06. Hz 0. Hz. Hz 7. Hz 0.7 Hz - - 07. Hz 6. Hz 6.7 Hz. Hz. Hz - - 0. Hz 7. Hz 6. Hz 6. Hz.7 Hz - - DA DIMMER 00: Fixed D A P P P P P 0-0: LED Indicators Brightness Level P 00 - : TFT Display Brightness Level D A D A P P P P DN MIC DWN D N DT DATE AND TIME 6 7 ~ n- n 0: Date D T P P P 6 P 7 ~ P 0 : Time (UTC) : Time differential (Time Zone) P =0 yyyymmdd (Year/Month/Date) D T = hhmmss (Hour/Minute/Second, hour time system) 6 7 ~ n- n = hhmm (Hour/Minute, 0 minute increments) D T P P P P ~ P ED ENCORDER DOWN 0: MAIN ENCORDER E D P P 6 7 0 : SUB ENCORDER : MULTI ENCORDER P 0 - : Steps EK ENT KEY E K 6
EU ENCORDER UP 0: MAIN ENCORDER E U P P 6 7 0 : SUB ENCORDER : MULTI ENCORDER P 0 - : Steps EX MENU 6 7 ~ n- n : 00 - (MENU Number) E X P P ~ P P : Parameter (See Table) E X 6 7 ~ n- n E X P P ~ P Function P Digits 00 AGC FAST DELAY 0 ~ 000 msec (P= 000 ~ 000, 0 msec/step) 00 AGC MID DELAY 0 ~ 000 msec (P= 000 ~ 000, 0 msec/step) 00 AGC SLOW DELAY 0 ~ 000 msec (P= 000 ~ 000, 0 msec/step) 00 HOME FUNCTION 0: SCOPE : FUNCTION 00 MY CALL INDICATION 0 ~ sec 006 DISPLAY COLOR 0: BLUE : GRAY : GREEN : ORANGE : PURPLE : RED 6: SKY BLUE 007 DIMMER LED 0: : 00 DIMMER TFT 00 ~ 00 BAR MTR PEAK HOLD 0: OFF : 0. sec :.0 sec :.0 sec 00 DVS RX OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 DVS TX OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 KEYER TYPE 0: OFF : BUG : ELEKEY-A : ELEKEY-B : ELEKEY-Y : ACS 0 KEYER DOT/DASH 0: NORNAL : REVERSE 0 CW WEIGHT. ~. (P = ~ ) 0 BEACON INTERVAL OFF / ~ 60 sec (P = 000 ~ 60, 000: OFF) 06 NUMBER STYLE 0: 0 : AUNO : AUNT : ANO : ANT : NO 6: NT 07 CONTEST NUMBER 0000 ~ 0 CW MEMORY 0: TEXT : MESSAGE 0 CW MEMORY 0: TEXT : MESSAGE 00 CW MEMORY 0: TEXT : MESSAGE 0 CW MEMORY 0: TEXT : MESSAGE 0 CW MEMORY 0: TEXT : MESSAGE 0 NB WIDTH 0: ms : ms : 0 ms 0 NB REJECTION 0: 0 db : 0 db : 0 db 0 NB LEVEL 0 ~ 0 (P = 00 ~ 0) 06 BEEP LEVEL 0 ~ 00 (P = 000 ~ 00) 07 TIME ZONE UTC :00 ~ +:00 0 GPS/C SELECT 0: GPS : RSC 0 C RATE 0: 00 bps : 600 bps : 00 bps : 00 bps 00 C TOT 0: 0 msec : 00 msec : 000 msec : 000 msec 0 CAT RATE 0: 00 bps : 600 bps : 00 bps : 00 bps 0 CAT TOT 0: 0 msec : 00 msec : 000 msec : 000 msec 0 CAT RTS 0: DISABLE : ENABLE 0 MEM GROUP 0: DISABLE : ENABLE 0 QUICK SPLIT FREQ 0 khz ~ +00 (or 00) ~ +0 khz (P= 0 ~ +00 or 00 ~ +0) 06 TX TOT 0 (OFF) ~ 0 min (P= 00 ~ 0) 07 MIC SCAN 0: DISABLE : ENABLE 0 MIC SCAN RESUME 0: PAUSE : TIME 0 REF FREQ ADJ ~ +00 (or 00) ~ + (P= ~ +00 or 00 ~ +) 00 CLAR MODE SELECT 0: RX : TX : TRX 0 AM LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 0 AM LCUT SLOPE 0: 6 db/oct : db/oct 0 AM HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 0 AM HCUT SLOPE 0: 6 db/oct : db/oct 0 AM MIC SELECT 0: MIC : REAR 06 AM OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 07 AM PTT SELECT 0: DAKY : RTS : DTR 0 AM PORT SELECT 0: DATA : USB 0 AM DATA GAIN 0 ~ 00 (P = 000 ~ 00) 00 CW LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 0 CW LCUT SLOPE 0: 6 db/oct : db/oct 0 CW HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 0 CW HCUT SLOPE 0: 6 db/oct : db/oct 0 CW OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 CW AUTO MODE 0: OFF : 0 MHz : ON 06 CW BK-IN TYPE 0: SEMI BREAK-IN : FULL BREAK-IN 07 CW BK-IN DELAY 0 ~ 000 msec (P = 000 ~ 000, 0 msec/step) 0 CW WAVE SHAPE 0: msec : msec : msec : 6 msec 0 CW FREQ DISPLAY 0: DIRECT FREQ : PITCH OFFSET 060 PC KEYING 0: OFF : DAKY : RTS : DTR 06 QSK DELAY TIME 0: msec : 0 msec : mesc : 0 msec 7
Function P Digits 06 DATA MODE 0: PSK : OTHER 06 PSK TONE 0: 000 Hz : 00 Hz : 000 Hz 06 OTHER DISP (SSB) 000 Hz ~ 0 ~ +000 Hz (P = 000 ~ 0000 or +0000 ~ +000, 0 Hz steps) 06 OTHER SHIFT (SSB) 000 Hz ~ 0 ~ +000 Hz (P = 000 ~ 0000 or +0000 ~ +000, 0 Hz steps) 066 DATA LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 067 DATA LCUT SLOPE 0: 6 db/oct : db/oct 06 DATA HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 06 DATA HCUT SLOPE 0: 6 db/oct : db/oct 070 DATA IN SELECT 0: MIC : REAR 07 DATA PTT SELECT 0: DAKY : RTS : DTR 07 DATA PORT SELECT : DATA : USB 07 DATA OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 07 FM MIC SELECT 0: MIC : REAR 07 FM OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 076 FM PKT PTT SELECT 0: DAKY : RTS : DTR 077 FM PKT PORT SELECT : DATA : USB 07 FM PKT TX GAIN 0 ~ 00 (P = 000 ~ 00) 07 FM PKT MODE 0: 00 : 600 00 RPT SHIFT MHz 0 ~ 000 khz (P = 0000 ~ 000, 0 khz/step) 0 RPT SHIFT 0MHz 0 ~ 000 khz (P = 0000 ~ 000, 0 khz/step) 0 RPT SHIFT MHz 0 ~ 000 khz (P = 0000 ~ 000, 0 khz/step) 0 RPT SHIFT 0MHz 0 ~ 0000 khz (P = 0000 ~ 0000, 0 khz/step) 0 ARS MHz 0: OFF : ON 0 ARS 0MHz 0: OFF : ON 06 DCS POLARITY 0: Tn-Rn : Tn-Riv : Tiv-Rn : Tiv-Riv 07 RADIO ID - - - - - - - - - - - 0 DIGITAL SQL TYPE 0: OFF : CODE : BREAK 0 DIGITAL SQL CODE 00 ~ 6 00 GM DISPLY 0: DISTANCE : STRENGTH 0 DISTANCE 0: km : mile 0 AMS TX MODE 0: AUTO : MANUAL : DN : VW : ANALOG 0 STANDBY BEEP 0: OFF : ON 0 RTTY LCUT FREQ 00: OFF 0: 00 Hz ~ : 000Hz (0 Hz steps) 0 RTTY LCUT SLOPE 0: 6 db/oct : db/oct 06 RTTY HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000Hz (0 Hz steps) 07 RTTY HCUT SLOPE 0: 6 db/oct : db/oct 0 RTTY SHIFT PORT 0: SHIFT : DTR : RTS 0 RTTY POLARITY-RX 0: NORNAL : REVERSE 00 RTTY POLARITY-TX 0: NORNAL : REVERSE 0 RTTY OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 RTTY SHIFT FREQ : 70 Hz : 00 Hz : Hz : 0 Hz 0 RTTY MARK FREQ : 7 Hz : Hz 0 SSB LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 0 SSB LCUT SLOPE 0: 6 db/oct : db/oct 06 SSB HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 07 SSB HCUT SLOPE 0: 6 db/oct : db/oct 0 SSB MIC SELECT 0: MIC : REAR 0 SSB OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 SSB PTT SELECT 0: DAKY : RTS : DTR SSB PORT SELECT 0: DATA : USB SSB TX BPF 0: 0 ~ 000 : 00 ~ 00 : 00 ~ 00 : 00 ~ 700 : 00 ~ 600 APF WIDTH 0: NARROW : MEDIUM : WIDE CONTOUR LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) CONTOUR WIDTH 0 ~ 6 IF NOTCH WIDTH 0: NARROW : WIDE 7 SCP DISPLAY MODE 0: SPECTRAM : WATER FALL SCP START CYCLE 0: OFF : sec : sec : 0 sec ASC DIAL SPEED 0: 0. khz/sec : 0. khz/sec : khz/sec : khz/sec : khz/sec : DISABLE 0 SCP SPAN FREQ 0: 0 khz 0: 00 khz 0: 00 khz 06: 00 khz 07: 000 khz PRMTRC EQ FREQ 00 : OFF 0: 00 0: 00 0: 00 0: 00 0: 00 06: 600 07: 700 Hz PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) PRMTRC EQ BWTH 0 ~ 0 PRMTRC EQ FREQ 00: OFF 0: 700 0: 00 0: 00 0: 000 0: 00 06: 00 07: 00 0: 00 0: 00 Hz PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) 6 PRMTRC EQ BWTH 0 ~ 0 7 PRMTRC EQ FREQ 00 : OFF 0: 00 0: 600 0: 700 0: 00 0: 00 06: 000 ~ : 00 Hz PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) PRMTRC EQ BWTH 0 ~ 0 0 P-PRMTRC EQ FREQ 00 : OFF 0: 00 0: 00 0: 00 0: 00 0: 00 06: 600 07: 700 Hz P-PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) P-PRMTRC EQ BWTH 0 ~ 0 P-PRMTRC EQ FREQ 00: OFF 0: 700 0: 00 0: 00 0: 000 0: 00 06: 00 07: 00 0: 00 0: 00 Hz P-PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) P-PRMTRC EQ BWTH 0 ~ 0 6 P-PRMTRC EQ FREQ 00 : OFF 0: 00 0: 600 0: 700 0: 00 0: 00 06: 000 ~ : 00 Hz 7 P-PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) P-PRMTRC EQ BWTH 0 ~ 0 HF TX MAX POWER ~ 00 (P = 00 ~ 00) 0 0M TX MAX POWER ~ 00 (P = 00 ~ 00) M TX MAX POWER ~ 0 (P = 00 ~ 00) 0M TX MAX POWER ~ 0 (P = 00 ~ 00) TUNER SELECT 0: OFF : INTERNAL : EXTERNAL : ATAS : LAMP
Function P Digits VOX SELECT 0: MIC : DATA VOX GAIN 000 ~ 00 6 VOX DELAY 0 ~ 000 msec (P = 000 ~ 000, 0 msec/step) 7 ANTI VOX GAIN 000 ~ 00 DATA VOX GAIN 000 ~ 00 DATA VOX DELAY 0 ~ 000 msec (P = 000 ~ 000) 0 ANTI DVOX GAIN 000 ~ 00 EMERGENCY FREQ TX 0: DISABLE : ENABLE FA FREQUENCY VFO-A 00000000-70000000 (Hz) F A 6 7 0 F A F A 6 7 0 FB FREQUENCY VFO-B 00000000-70000000 (Hz) F B 6 7 0 F B F B 6 7 0 FS FAST STEP 0: VFO-A FAST Key OFF F S : VFO-A FAST Key ON F S F S FT FUNCTION TX : VFO-A Band Transmitter: TX F F T T 6 7 0 : VFO-B Band Transmitter: TX P 0: VFO-A Band Transmitter: TX : VFO-B Band Transmitter: TX F T P GT AGC FUNCTION 0: Fixed P 0: AGC OFF G T P P 0: AGC OFF : AGC FAST : AGC FAST : AGC MID : AGC MID : AGC SLOW G T : AGC SLOW : AGC AUTO-FAST : AGC AUTO : AGC AUTO-MID 6: AGC AUTO-SLOW G T P ID IDENTIFICATION 070: FT- I D I D
IF INFORMATION 000-7 (Memory Channel) P VFO-A Frequency (Hz) P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: 0000 - (Hz) P 0: RX CLAR OFF : RX CLAR ON I F P 0: TX CLAR OFF : TX CLAR ON P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB I F P P P P P D: AM-N E: CFM 6 7 0 P7 0: VFO : Memory : Memory Tune : Quick Memory Bank (QMB) : QMB-MT : PMS 6: HOME P P P P P P P P P P P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC 6 7 0 P 00: (Fixed) P P6 P7 P P P 0 0 0: Simplex : Plus Shift : Minus Shift IS IF-SHIFT 0:Fixed I S -/+ P P P P P -000 ~ +000 Hz (0 Hz steps) I S I S -/+ P P P P KM KEYER MEMORY 6 7 ~ n - : Keyer Memory Channel Number K M P P P P ~ P P Message Characters (up to 0 characters) K M 6 7 ~ n- n K M P P P P ~ P KP KEY PITCH 00: 00 Hz - 7: 00 Hz (0Hz steps) K P K P K P KR KEYER 0: KEYER OFF K R : KEYER ON K R K R KS KEY SPEED 00-060 (WPM) K S K S K S KY CW KEYING : Keyer Memory Playback 6: Message Keyer Playback K Y : Keyer Memory Playback 7: Message Keyer Playback : Keyer Memory Playback : Message Keyer Playback : Keyer Memory Playback : Message Keyer Playback : Keyer Memory Playback A: Message Keyer Playback 0
LK LOCK 0: VFO-A DIAL Lock OFF L K : VFO-A DIAL Lock ON L K L K LM LOAD MESSEGE 0: DVS P 0: DVS (Recording Stop) L L M M P 6 6 7 7 0 0 : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) L M P MA MEMORY CHANNEL TO VFO-A M A MC MEMORY CHANNEL 000-7: Memory Channel Number M C 000-0: Regular Memory Channel 00: P-L 0: P-U ~ 6: P-L 7: P-U M C M C MD OPERATING MODE 0: MAIN RX M D P P MODE : LSB : USB : CW-U : FM : AM 6: RTTY-LSB 7: CW-L : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM M D M D P MG MIC GAIN 000-00 M G M G M G ML MONITOR LEVEL 0: MONI ON/OFF M L P P P : MONI Level P =0 000: MONI OFF M L 00: MONI ON = 000-00 M L P P P
MR MEMORY CHANNEL READ P0/ 000-7 (Memory Channel) P VFO-A Frequency (Hz) P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: 0000 - (Hz) P 0: RX CLAR OFF : RX CLAR ON M R P0 P0 P0 P 0: TX CLAR OFF : TX CLAR ON P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R M R P P P P P : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM 6 7 0 P7 0: VFO : Memory P P P P P P P P P P P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC 6 7 0 P 00: (Fixed) P P6 P7 P P P 0 0 0: Simplex : Plus Shift : Minus Shift MS METER SW 0: COMP M M S S 6 6 7 7 0 0 : ALC : PO : SWR : ID : VDD M S MW MEMORY CHANNEL WRITE 000-7 (Memory Channel) P Frequency (Hz) M W P P P P P P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: 0000 - (Hz) 6 7 0 P 0: RX CLAR OFF : RX CLAR ON P P P P P P P P P P P 0: TX CLAR OFF : TX CLAR ON 6 7 0 P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R P P6 P7 P P P 0 : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM P7 00: (Fixed) P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) 0 0: Simplex : Plus Shift : Minus Shift MX MOX SET 0: MOX OFF M X : MOX ON M X M X NA NARROW 0: Fixed M A P P 0: OFF : ON M A M A P NB NOISE BLANKER STATUS 0: Fixed N B P P 0: Noise Blanker OFF : Noise Blanker ON N B N B P NL NOISE BLANKER LEVEL 0: Fixed N L P P P P 000-00 N L N L P P P
NR NOISE REDUCTION 0: Fixed N R P P 0: Noise Reduction OFF : Noise Reduction ON N R N R P OI OPPOSITE BAND INFORMATION 000-7 (Memory Channel) P VFO-B Frequency (Hz) P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: 0000 - (Hz) P 0: RX CLAR OFF : RX CLAR ON O I P 0: TX CLAR OFF : TX CLAR ON P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R O I P P P P P : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM 6 7 0 P7 0: VFO : Memory P P P P P P P P P P P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC 6 7 0 P 00: (Fixed) P P6 P7 P P P 0 0 0: Simplex : Plus Shift : Minus Shift OS OFFSET (REPEATER SHIFT) 0: Fixed O O S S P 6 7 0 P 0: Simplex : Plus Shift : Minus Shift *: This command can be activated only with an FM mode. O S P PA PRE-AMP (IPO) 0:Fixed P P A A P 6 7 0 P 0: IPO : AMP : AMP P A P PB PLAY BACK 0: DVS P 0: DVS (Playback Stop) P P B B P 6 6 7 7 0 0 : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) P B P PC POWER CONTROL 00-00 P C P C P C PL SPEECH PROCESSOR LEVEL 000-00 P L P L P L
PR SPEECH PROCESSOR LEVEL 0: Speech Processor P P R R P 6 7 0 : Parametric Microphone Equalizer P : OFF : ON P R P PS POWER SWITCH 0: POWER OFF P S : POWER ON P S P S This command requires dummy data be initially sent. Then after one second and before two seconds the command is sent. QI QMB STORE Q I QR QMB RECALL Q R QS QUICK SPLIT Q S RA RF ATTENUATOR 0: Fixed R A P P 0: OFF : ON R A R A P RC CLAR CLEAR R C RD CLAR DOWN 0000 - (Hz) R D
RG RF GAIN 0: Fixed R G P P P P 000 - R G R G P P P RI RADIO INFORMATION 0: Hi-SWR A: TX LED P 0: OFF : REC : ON : PLAY : VFO-A TX R I 6: VFO-B TX 7: VFO-A RX R I P RL NOISE REDUCTION LEVEL 0: Fixed R L P P P 0 - R L R L P P RM READ METER 0: Depends on the front panel METER : ALC : S : PO : Depends on the front panel METER 6: SWR (PO / COMP / ALC / SWR / ID / VDD) 7: ID R M : COMP : VDD P 0 - R M P P P RS RADIO STATUS 0: NORMAL MODE : MENU MODE R S R S RT CLAR 0: RX Clariier OFF R T : RX Clariier ON R T R T RU RX CLARIFIER PLUS OFFSET 0000 - (Hz) R U SC SCAN 0: Scan OFF S C : Scan ON (UP ward) : Scan ON (DOWN ward) S C S C
SD CW BREAK-IN DELAY TIME 000-000 msec S D S D S D SH WIDTH 0: Fixed S H P P P 00 (See Table) S H S H P P Command Bandwidth P SSB (Narrow) SSB (Wide) CW (Narrow) CW (Wide) RTTY/PSK (Narrow) RTTY/PSK (Wide) 00 (Default) 00 Hz 00 Hz 00 Hz 00 Hz 00 Hz 00 Hz 0 00 Hz - 0 Hz - 0 Hz - 0 00 Hz - 00 Hz - 00 Hz - 0 600 Hz - 0 Hz - 0 Hz - 0 0 Hz - 00 Hz - 00 Hz - 0 00 Hz - 0 Hz - 0 Hz - 06 0 Hz - 00 Hz - 00 Hz - 07 00 Hz - 0 Hz - 0 Hz - 0 60 Hz - 00 Hz - 00 Hz - 0 00 Hz 00 Hz 0 Hz - 0 Hz - 0-0 Hz 00 Hz 00 Hz 00 Hz 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 700 Hz - 700 Hz - 00 Hz - 000 Hz - 000 Hz 6-600 Hz - 00 Hz - 00 Hz 7-700 Hz - 000 Hz - 000 Hz - 00 Hz - - - - - 00 Hz - - - - 0-000 Hz - - - - - 00 Hz - - - - SM S-METER READING 0: Fixed P 000 - S M S M P P P SQ SQUELCLH LEVEL 0: Fixed S Q P P P P 000-00 S Q S Q P P P SV SWAP VFO S V 6
TS TXW 0: TXW OFF T S : TXW ON T S T S TX TX SET 0: RADIO TX OFF CAT TX OFF T X : RADIO TX OFF CAT TX ON : RADIO TX ON CAT TX OFF () T X T X UL PLL UNLOCK STATUS 0: PLL Lock : PLL Unlock U L U L UP UP U P VD VOX DELAY TIME 000-000 msec (0 msec multiples) V D V D V D VG VOX GAIN 000-00 V G V G V G VM VFO-A TO MEMORY CHANNEL V M VX VOX STATUS 0: VOX OFF V X : VOX ON V X V X 7
XT TX CLAR 0: TX CLAR OFF X T : TX CLAR ON X T X T ZI ZERO IN (CW AUTO ZERO IN Function) Z I
Copyright 0 YAESU MUSEN CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. 0-A0