John Lewis Mia Bed ouble King size Stock ode: 80/80 Stock ode: 80/80 Thank you for purchasing this Mia Bed. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. For product support or spare parts please call the John Lewis Helpline; T: 0 68999 E: mail@fwgroup-uk.com PRE-ASSEMBLY PREPARATION Please ensure instructions are read in full before attempting to assemble this product. Necessary Tools Please check the pack contents before attempting to assemble this product. A full checklist of components is given in this leaflet. If any components are missing, please contact your the John Lewis Helpline. This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE ARE WHEN LIFTING to avoid personal injury and (or) damage to the product. This product takes approximately 0 MINUTES to assemble with PEOPLE. The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG HILREN. Read this leaflet in full before commencing assembly. If you require any additional information or have any issues with this product please call the John Lewis Helpline on 0 68999 or email mail@fwgroup-uk.com
Fitting and parts checklist A M Allen Key x Side aps x 0 B M Allen Key x E M6 X mm Bolts x entre aps x F M6 X 0mm Bolts x 8 Headboard x Footboard x Side Rails x Slats x 0 entre Rail x 6 Legs x
Step by step assembly instructions Step One Place wooden legs (6) over the holes in the underside of the headboard () and foot board () as per below drawing. M6 x 0 bolt M6 x 0 bolt M6 x 0 bolt Allen Key M6 x 0 bolt Bed Leg Pre-inserted Nut Head/Foot Board M (A) (M6) x 8 (6) x Step Two Place brackets on side rails () over pre-inserted bolts in headboard () and foot board (). Tighten bolts using allen key M (B) to secure parts together. AN BRAKET SIE RAIL M AN BRAKET SIE RAIL M (B)
Step Three Insert centre rail () into the brackets in the centre of the headboard () and foot board (). Push down fully and secure in place using M6 x mm bolt (E) tighten using allen key M (A). STEP entre Rail STEP M6 x mm E. A. M M6 x mm M Step Four Push the centre plastic caps () into the holes along the centre rail (). Once in place, insert a slat () into the centre plastic cap followed by a side cap (). Finally push the side plastic cap into the holes on the side rail (). Repeat this process for all slats. x. x0. SlatS (0pcs) entre aps ( pcs). Side aps (0 pcs)
are and Maintenance This Mia bedstead should be cleaned using a soft damp cloth and dried immediately. o not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently damage the surface. o not use detergents and do not rub as this can cause permanent damage. Always protect your bed from direct sunlight as this may accelerate the natural on going discolouration process. Screws holding together the bed frame should be tightened regularly. Please retain this information leaflet for future reference. This product complies with BS 7:98 Safety Instructions Never drag furniture when moving it, always lift it. Periodically check all fixings to ensure none have come loose and re-tighten where necessary. Please take care when handling or moving the furniture as careless handling may cause damage or injury. Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by competent adults. No liability will be accepted for damage or injury caused by incorrectly insalled or assembled furniture. uring assembly children should be kept away from the product due to possible risk of injury. o not use this item if any components are missing or damaged. It is recommended that care is taken when moving heavy objects to a new location to avoid personal injury or damage to the furniture. Please be careful to retain all fitting when doing this. If you require any additional information or have any issues with this product please call the John Lewis Helpline on 0 68999 or email mail@fwgroup-uk.com John Lewis Partnership 7 Victoria Street, London, SWIE NN. www.johnlewis.com