Power MOSFET PRODUCT SUMMARY V DS (V) 100 R DS(on) (Ω) = 10 V 0.54 Q g (Max.) (nc) 8.3 Q gs (nc) 2.3 Q gd (nc) 3.8 Configuration Single FEATURES Dynamic dv/dt Rating Repetitive Avalanche Rated 175 C Operating Temperature Fast Switching Ease of Paralleling Simple Drive Requirements Lead (Pb)-free Available Available RoHS* COMPLIANT TO-220 G DS G D S N-Channel MOSFET DESCRIPTION Third generation Power MOSFETs from Vishay provide the designer with the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness. The TO-220 package is universally preferred for all commercial-industrial applications at power dissipation levels to approximately 50 W. The low thermal resistance and low package cost of the TO-220 contribute to its wide acceptance throughout the industry. ORDERING INFORMATION Package Lead (Pb)-free SnPb TO-220 IRF510PbF SiHF510-E3 IRF510 SiHF510 ABSOLUTE MAXIMUM RATINGS T C = 25 C, unless otherwise noted PARAMETER SYMBOL LIMIT UNIT Drain-Source Voltage V DS 100 V Gate-Source Voltage ± 20 Continuous Drain Current at 10 V T C = 25 C 5.6 I D T C = 100 C 4.0 A Pulsed Drain Current a I DM 20 Linear Derating Factor 0.29 W/ C Single Pulse Avalanche Energy b E AS 100 mj Repetitive Avalanche Current a I AR 5.6 A Repetitive Avalanche Energy a E AR 4.3 mj Maximum Power Dissipation T C = 25 C P D 43 W Peak Diode Recovery dv/dt c dv/dt 5.5 V/ns Operating Junction and Storage Temperature Range T J, T stg - 55 to 175 Soldering Recommendations (Peak Temperature) for 10 s 300 d C Mounting Torque 6-32 or M3 screw Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. V DD = 25 V, starting T J = 25 C, L = 4.8 mh, R G = 25 Ω, I AS = 5.6 A (see fig. 12). c. I SD 5.6 A, di/dt 75 A/µs, V DD V DS, T J 175 C. d. 1.6 mm from case. * Pb containing terminations are not RoHS compliant, exemptions may apply 10 lbf in 1.1 N m Document Number: 91015 S-81377-Rev. A, 30-Jun-08 1
THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYP. MAX. UNIT Maximum Junction-to-Ambient R thja - 62 Case-to-Sink, Flat, Greased Surface R thcs 0.50 - C/W Maximum Junction-to-Case (Drain) R thjc - 3.5 SPECIFICATIONS T J = 25 C, unless otherwise noted PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Static Drain-Source Breakdown Voltage V DS = 0 V, I D = 250 µa 100 - - V V DS Temperature Coefficient ΔV DS /T J Reference to 25 C, I D = 1 ma - 0.12 - V/ C Gate-Source Threshold Voltage (th) V DS =, I D = 250 µa 2.0-4.0 V Gate-Source Leakage I GSS = ± 20 V - - ± 100 na V DS = 100 V, = 0 V - - 25 Zero Gate Voltage Drain Current I DSS V DS = 80 V, = 0 V, T J = 150 C - - 250 µa Drain-Source On-State Resistance R DS(on) = 10 V I D =3.4 A b - - 0.54 Ω Forward Transconductance g fs V DS = 50 V, I D = 3.4 A b 1.3 - - S Dynamic Input Capacitance C iss = 0 V, - 180 - Output Capacitance C oss V DS = 25 V, - 81 - pf Reverse Transfer Capacitance C rss f = 1.0 MHz, see fig. 5-15 - Total Gate Charge Q g I D = 5.6 A, V DS = 80 V - - 8.3 Gate-Source Charge Q gs = 10 V V DS = 10 V, - - 2.3 nc Gate-Drain Charge Q gd see fig. 6 and 13 b - - 3.8 Turn-On Delay Time t d(on) - 6.9 - Rise Time t r V DD = 50 V, I D = 5.6 A - 16 - Turn-Off Delay Time t d(off) R G = 24 Ω, R D = 8.4 Ω, see fig. 10 b - 15 - ns Fall Time t f - 9.4 - Between lead, D Internal Drain Inductance L D - 4.5-6 mm (0.25") from G package and center of Internal Source Inductance L S die contact - 7.5 - S nh Drain-Source Body Diode Characteristics MOSFET symbol Continuous Source-Drain Diode Current I S showing the - - 5.6 D integral reverse G Pulsed Diode Forward Current a I SM p - n junction diode - - 20 S A Body Diode Voltage V SD T J = 25 C, I S = 5.6 A, = 0 V b - - 2.5 V Body Diode Reverse Recovery Time t rr - T J = 25 C, I F = 5.6 A, di/dt = 100 A/µs b 100 200 ns Body Diode Reverse Recovery Charge Q rr - 0.44 0.88 µc Forward Turn-On Time t on Intrinsic turn-on time is negligible (turn-on is dominated by L S and L D ) Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. Pulse width 300 µs; duty cycle 2 %. Document Number: 91015 2 S-81377-Rev. A, 30-Jun-08
TYPICAL CHARACTERISTICS 25 C, unless otherwise noted I D, Drain Current (A) 10 1 10 0 Top 15 V 10 V 8.0 V 7.0 V 6.0 V 5.5 V 5.0 V Bottom 4.5 V 4.5 V I D, Drain Current (A) 10 1 10 0 25 C 175 C 20 µs Pulse Width T C = 25 C 10-1 20 µs Pulse Width V DS = 50 V 10-1 10 0 10 1 4 5 6 7 8 9 10 91015_01 V DS, Drain-to-Source Voltage (V) 91015_03, Gate-to-Source Voltage (V) Fig. 1 - Typical Output Characteristics, T C = 25 C Fig. 3 - Typical Transfer Characteristics I D, Drain Current (A) 91015_02 10 1 10 0 Top Bottom 15 V 10 V 8.0 V 7.0 V 6.0 V 5.5 V 5.0 V 4.5 V 4.5 V 20 µs Pulse Width T C = 175 C 10-1 10 0 10 1 V DS, Drain-to-Source Voltage (V) R DS(on), Drain-to-Source On Resistance (Normalized) 91015_04 3.0 2.5 2.0 1.5 1.0 0.5 I D = 5.6 A = 10 V 0.0-60 - 40-20 0 20 40 60 80 100 120 140160 180 T J, Junction Temperature ( C) Fig. 2 - Typical Output Characteristics, T C = 175 C Fig. 4 - Normalized On-Resistance vs. Temperature Document Number: 91015 S-81377-Rev. A, 30-Jun-08 3
Capacitance (pf) 91015_05 400 320 240 160 80 0 10 0 10 1 = 0 V, f = 1 MHz C iss = C gs C gd, C ds Shorted C rss = C gd C oss = C ds C gd C iss C oss C rss V DS, Drain-to-Source Voltage (V) I SD, Reverse Drain Current (A) 91015_07 10 0 10-1 175 C 25 C = 0 V 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 V SD, Source-to-Drain Voltage (V) Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage Fig. 7 - Typical Source-Drain Diode Forward Voltage, Gate-to-Source Voltage (V) 91015_06 20 16 12 8 4 0 I D = 5.6 A V DS = 20 V V DS = 50 V V DS = 80 V 0 2 4 6 8 Q G, Total Gate Charge (nc) For test circuit see figure 13 10 I D, Drain Current (A) 91015_08 10 2 5 2 10 5 2 1 5 2 0.1 2 5 1 10 Operation in this area limited by R DS(on) T C = 25 C T J = 175 C Single Pulse 2 5 100 µs 1 ms 10 ms 10 2 2 5 V DS, Drain-to-Source Voltage (V) 10 3 Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage Fig. 8 - Maximum Safe Operating Area Document Number: 91015 4 S-81377-Rev. A, 30-Jun-08
V DS R D I D, Drain Current (A) 6.0 5.0 4.0 3.0 2.0 1.0 Fig. 10a - Switching Time Test Circuit V DS 90 % R G 10 V Pulse width 1 µs Duty factor 0.1 % D.U.T. - V DD 91015_09 0.0 25 50 75 100 125 150 T C, Case Temperature ( C) 175 10 % t d(on) t r t d(off) t f Fig. 9 - Maximum Drain Current vs. Case Temperature Fig. 10b - Switching Time Waveforms 10 Thermal Response (Z thjc ) 1 0.1 0-0.5 0.2 0.1 0.05 0.02 0.01 Single Pulse (Thermal Response) 10-2 10-5 10-4 10-3 10-2 0.1 1 10 P DM t 1 t 2 Notes: 1. Duty Factor, D = t 1 /t 2 2. Peak T j = P DM x Z thjc T C 91015_11 t 1, Rectangular Pulse Duration (s) Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case Vary t p to obtain required I AS R G V DS L D.U.T I AS - V DD V DS t p V DS V DD 10 V t p 0.01 Ω A I AS Fig. 12a - Unclamped Inductive Test Circuit Fig. 12b - Unclamped Inductive Waveforms Document Number: 91015 S-81377-Rev. A, 30-Jun-08 5
E AS, Single Pulse Energy (mj) 91015_12c 300 250 200 150 100 50 Top Bottom V DD = 25 V 0 25 50 75 100 125 150 I D 2.3 A 4.0 A 5.6 A Starting T J, Junction Temperature ( C) 175 Fig. 12c - Maximum Avalanche Energy vs. Drain Current Current regulator Same type as D.U.T. 10 V Q G 12 V 0.2 µf 50 kω 0.3 µf Q GS Q GD D.U.T. V - DS V G Charge Fig. 13a - Basic Gate Charge Waveform 3 ma Fig. 13b - Gate Charge Test Circuit I G I D Current sampling resistors Document Number: 91015 6 S-81377-Rev. A, 30-Jun-08
Peak Diode Recovery dv/dt Test Circuit D.U.T. - Circuit layout considerations Low stray inductance Ground plane Low leakage inductance current transformer - - R G dv/dt controlled by R G Driver same type as D.U.T. I SD controlled by duty factor "D" D.U.T. - device under test - V DD Driver gate drive P.W. Period D = P.W. Period = 10 V* D.U.T. I SD waveform Reverse recovery current Re-applied voltage Body diode forward current di/dt D.U.T. V DS waveform Diode recovery dv/dt Inductor current Body diode forward drop V DD Ripple 5 % I SD * = 5 V for logic level devices Fig. 14 - For N-Channel maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see http:///ppg?91015. Document Number: 91015 S-81377-Rev. A, 30-Jun-08 7
Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 1
R-C Thermal Model Parameters IRF510_RC, SiHF510_RC DESCRIPTION The parametric values in the R-C thermal model have been derived using curve-fitting techniques. R-C values for the electrical circuit in the Foster/tank and Cauer/filter configurations are included. When implemented in P-SPICE, these values have matching characteristic curves to the single-pulse transient thermal impedance curves for the MOSFET. These RC values can be used in the P-SPICE simulation to evaluate the thermal behavior of the MOSFET junction temperature under a defined power profile. These techniques are described in application note AN609, Thermal Simulation of Power MOSFETs on the P-SPICE Platform. R-C THERMAL MODEL FOR TANK CONFIGURATION T (Junction) RT1 RT2 RT3 RT4 T (Ambient) CT1 CT2 CT3 CT4 R-C VALUES FOR TANK CONFIGURATION THERMAL RESISTANCE ( C/W) Junction to Ambient Case Foot RT1 N/A 917.7500 m N/A RT2 N/A 598.2000 m N/A RT3 N/A 1.8542 N/A RT4 N/A 129.9000 m N/A THERMAL CAPACITANCE (Joules/ C) Junction to Ambient Case Foot CT1 N/A 118.7943 m N/A CT2 N/A 2.1686 m N/A CT3 N/A 9.6739 m N/A CT4 N/A 251.2953 u N/A Note N/A indicates not applicable This document is intended as a SPICE modeling guideline and does not constitute a commercial product datasheet. Designers should refer to the appropriate datasheet of the same number for guaranteed specification limits. Document Number: 90234 Revision: 25-Feb-10 1
IRF510_RC, SiHF510_RC R-C THERMAL MODEL FOR FILTER CONFIGURATION T (Junction) RF1 RF2 RF3 RF4 T (Ambient) CF1 CF2 CF3 CF4 GND R-C VALUES FOR FILTER CONFIGURATION THERMAL RESISTANCE ( C/W) Junction to Ambient Case Foot RF1 N/A 368.9562 m N/A RF2 N/A 845.9403 m N/A RF3 N/A 1.7024 N/A RF4 N/A 582.7035 m N/A THERMAL CAPACITANCE (Joules/ C) Junction to Ambient Case Foot CF1 N/A 494.4644 u N/A CF2 N/A 2.4212 m N/A CF3 N/A 8.3073 m N/A CF4 N/A 165.3498 m N/A Note N/A indicates not applicable Document Number: 90234 2 Revision: 25-Feb-10
IRF510_RC, SiHF510_RC Document Number: 90234 Revision: 25-Feb-10 3