Modulock Rised Deck Supports - Introduction Hrmer Roof Dringe The Modulock Rised Deck Support Rnges Fully engineered, verstile, rised deck product rnges, Modulock Pedestl nd Modulock Uni-Ring, re idel for conceled dringe nd the support of pving slbs, timber or sheet decking t vrying heights from the sub-structure. 76 www.hrmerdringe.co.uk
Modulock Rised Deck Supports - Benefits The Modulock Pedestl nd Modulock Uni-Ring rised deck supports re designed for use in terrces, wlkwys, blconies nd bllsted flt roof constructions. Reinforced djustment key Modulock Pedestl - Adjustble Height Wide rnge of height djustment from.5mm - 550mm Fine djustment for both height nd level re possible Self-Levelling Hed The Modulock Pedestl self-levelling hed compenstes for grdients up to 5º Mde of polypropylene nd rubber to provide n nti-noise nd nti-slip bedding surfce Self-Locting Locting bldes on Modulock Pedestl self-levelling hed ssist positioning of slbs nd mintining open joints when required Locting bldes cn be removed if required Comptibility Hrmer Modulock Pedestl nd Uni-Ring product rnges re fully comptible with the Modulock Chnnel Drin rnge Locting tbs for esy removl if required Self-levelling hed Coupling hed Robust Resistnt to tempertures from -40º to +120ºC UV stble nd resistnt to cids Instlltion Modulock Pedestl nd Modulock Uni-Ring re quick nd esy to instll, nd provide fst, efficient dringe through the open joints of the slbs to the conceled dringe wy below. Modulock Uni-Ring/Uni-Plus - Height Supports Uni-Ring gives fixed height of 16mm. Shims offer fine djustment in increments of 3mm Uni-Plus provides djustment of 25-40mm Screw coupling extension component Supporting bse with dringe holes Uni-Ring Uni-Plus Hrmer Technicl Helpline +44 (0) 1744 648400 77
Modulock Rised Deck Supports - Product Rnge Summry Modulock Pedestl Adjustble Height Supports MB1 MB2 MB3 MB4 Modulock Pedestl comprises bsic modules, ech with supporting hed nd bse component, llowing wide rnge of void heights. Modules re used either individully or in combintion to give floor voids rnging from.5mm to 550mm. A stble sub-bse nd n dequte mens of surfce wter dringe re virtully the only prerequisites for the use of the Modulock Pedestl system. Irregulr, stepped, uneven or sloping sub-bses cn usully be esily surmounted by the system resulting in new level rised floor. See pge 80. MB5 MB6 MB7 MB8 MB9 MB10 MB11 MB12 MB13 MB Modulock Uni-Ring Height Supports Uni-Ring Uni-Plus A verstile nd economic rnge for conceled dringe beneth pving slbs. The bsic Modulock Uni-Ring system within the rnge is bsed on shllow injection moulded polyethylene rings tht re positioned to support djoining slbs t ech corner whilst mintining open joints for dringe. It includes shims for fine height djustment. Modulock Uni-Plus is prt of the Uni-Ring system nd provides djustment of between 25-40mm. See pge 81. 78 www.hrmerdringe.co.uk
Modulock Rised Deck Supports - Product Rnge Summry Hrmer Technicl Helpline +44 (0) 1744 648400 79
Modulock Rised Deck Supports - Pedestl The Pedestl rnge of deck supports provides comprehensive rnge of djustment from.5mm to 550mm. The system fetures self-levelling heds with vriety of dividers for preset dringe gps in supported pving s well s heds without dividers for screw fixing decking bttens. An extended key llows for fine djustment of supports fter slb lying. 4 12 Self-levelling Hed with 12mm x 4mm Tbs MB1 MB2 MB3 MB4 MB5 Ech module hs 205mm di bse 4 12 Self-levelling Hed with 12mm x 4mm Tbs Module Combintion Height Adjustment Product Type (mm) Code Module without extension coupler.5-50 MB1 Module without extension coupler 50-75 MB2 Module without extension coupler 75-120 MB3 Module without extension coupler 120-170 MB4 Module without extension coupler 170-215 MB5 4 12 Self-levelling Hed with 12mm x 4mm Tbs MB6 MB7 MB8 Ech module hs 205mm di bse Module Combintion Height Adjustment Product Type (mm) Code Module with 1 extension coupler 0-230 MB6 Module with 1 extension coupler 185-275 MB7 Module with 1 extension coupler 235-325 MB8 4 12 Self-levelling Hed with 12mm x 4mm Tbs MB9 MB10 MB11 Ech module hs 205mm di bse Module Combintion Height Adjustment Product Type (mm) Code Module with 2 extension couplers 205-345 MB9 Module with 2 extension couplers 250-385 MB10 Module with 2 extension couplers 300-400 MB11 MB12 MB13 MB Ech module hs 205mm di bse Module Combintion Height Adjustment Product Type (mm) Code Module with 3 extension couplers 270-455 MB12 Module with 3 extension couplers 315-500 MB13 Module with 3 extension couplers 365-550 MB Optionl Accessories 2/3 C1 12 125 KEY 2/3/4 97 Ø 162 H12/2, 3 HF FH/2, 3, 4 Component Options Product Code Extension Coupler C1 Self-levelling Hed with 20mm x 2mm Tbs H20/2 Self-levelling Hed with 20mm x 3mm Tbs H20/3 Self-levelling Hed with 20mm x 4mm Tbs H20/4 Self-levelling Hed with 12mm x 2mm Tbs H12/2 Self-levelling Hed with 12mm x 3mm Tbs H12/3 Self-levelling Flt Hed H/F Fixed Hed with 23m x 2mm Tbs FH/2 Fixed Hed with 23m x 3mm Tbs FH/3 Fixed Hed with 23m x 4mm Tbs FH/4 Adjustment Key KEY 20 20 H20/2, 3, 4 2/3/4 66 23 18 80 www.hrmerdringe.co.uk
Modulock Rised Deck Supports - Uni-Ring nd Uni-Plus Uni-Ring nd Uni-Plus re verstile nd economic pving supports. Uni-Ring supports provide 16mm deck void nd cn be stcked in combintion with 3mm Uni-Shims for dditionl height correction. Uni-Plus is low level height djustble system providing 25mm to 40mm of djustment. Uni-Ring Hrmer Uni-Ring is quick nd esy to instll, nd provides fst, efficient dringe through the open joints of the slbs to the conceled dringe below. The system is idel for ny wterproofed substructure nd especilly for inverted roof constructions where bllsted insultion is lid onto the wterproofing lyer of the flt roof. Trditionl bedding nd grouting mterils re not required, nd once instlled, the pving slbs cn be esily lifted for simple inspection of the dringe outlets nd for substructure mintennce. Ring with collpsible spcers Height djustment shims Product b c (mm) (mm) (mm) Code Uni-Ring 176 25 16 uni-ring c b A mximum of two Uni-Shims cn be used per Uni-Ring b Product b (mm) (mm) Code Uni-Shim 110 3 uni-shim Uni-Plus Hrmer Uni-Plus is n economicl low level height djustble system tht is djusted on screw mechnism to provide height djustments of 25mm to 40mm. The hed fetures collpsible spcers for ese of instlltion in corners nd perimeter wll situtions. Uni-Plus is suitble for use where the floting deck is to be lid prllel to the roof deck i.e. does not hve ny slope correcting fetures. b c d Product b c d (mm) (mm) (mm) (mm) Code Uni-Plus 205 110 25-40 25 uni-plus Hrmer Technicl Helpline +44 (0) 1744 648400 81
Modulock Rised Deck Supports - NBS Specifiction A typicl NBS Specifiction for Hrmer Modulock rised deck supports. A full rnge of NBS specifictions re vilble vi the Hrmer online NBS Specifiction Builder t www.hrmerdringe.co.uk. For project specific specifiction dvice, contct Hrmer Technicl Services. J41 Reinforced Bitumen Membrne Roof Coverings GENERAL 110 REINFORCED BITUMEN MEMBRANE ROOF COVERINGS ALUMASC WATERPROOFING MEMBRANE SYSTEM SYSTEM PERFORMANCE 210 GENERAL Secure, free drining nd wethertight PRODUCTS 467 SUPPORT SYSTEMS FOR PRECAST CONCRETE PAVING SLABS Mnufcturer: Alumsc Exterior Building Products Ltd, White House Works, Bold Rod, Sutton St Helens, Merseyside WA9 4JG Tel: 01744 648400, Fx: 01744 648401. Emil: info@lumsc-exteriors.co.uk Type: Size: Adjustble deck supports MB1: 32 50 mm high/mb2: 50 75 mm high/mb3: 75 120 mm high /MB4: 120 200 mm high/mb5: 190 270 mm Product Code: MB1 MB5 Reference: Accessories: Hrmer Deck Modulock Levelers Crete Hrmer Modulock NBS specifictions by selecting the required product rnge, profile, size nd finish by visiting: www.hrmerdringe.co.uk Design Support Hrmer hs developed dedicted design softwre to ssist rchitects, specifiers nd contrct engineers to quntify the exct specifiction nd detiled lyout of Modulock Pedestls on project. Complex roof lyouts with multiple flls nd wkwrd detiling cn lso be clculted. Simply send through your CAD drwings to Hrmer s Technicl Deprtment nd we will do the rest. Key Fetures Design softwre is AutoCAD-comptible llowing semless interprettion of project design Multiple roof res nd complex roof lyouts cn be mpped using colour-coded lyout to show the exct specifiction nd height requirement of ech Modulock Pedestl Assists specifiction by ccurtely quntifying the exct number nd type of Modulock Pedestls required on project Improves the interfce between designers nd instller through ccurte specifiction nd product selection Contct: modulock@lumsc-exteriors.co.uk 82 www.hrmerdringe.co.uk
Modulock Rised Deck Supports - Instlltion Hrmer Pedestl A stble sub-bse nd, in the cse of exposed externl use, n dequte mens of surfce wter dringe re virtully the only prerequisites for the use of the Hrmer Modulock system. Irregulr, stepped, uneven or sloping sub-bses cn usully be esily surmounted by the system resulting in new level rised floor. The brod sequences of instlltion re illustrted in reltion to typicl pved pedestrin deck erected over n existing drined sub-bse. Alterntive Edge Detils 1. With wide open joint t perimeter. Pedestl with ll locting bldes removed Instlltion Sequence 1. Check condition of sub-bse, wterproofing nd dringe points. Rectify ny defects nd cler dringe outlets s preliminry mesure. Pedestl with two locting bldes removed 2. Set out pttern of pedestl supports, selected to suit new deck height nd pving modules. 3. Use supporting heds with liner blde configurtions t edges of deck nd t ny intermedite surfce interruptions. 4. Adjust pedestl screwjcks to the pproximte height required, checking for level nd lignment. 5. Finlise the lyout of the pedestls. For convenience, use lightweight templte for checking positions nd to void undue lifting of hevy pving slbs. 6. Proceed to ly the pving slbs, ensuring tht ech slb corner is firmly seted on the pedestl hed nd butted up to the locting bldes. 7. Finl djustment to level cn be mde by using the djustment key. Pedestl with ll four locting bldes retined 2. With nrrow open joint t perimeter. Pedestl with flnge cut wy on two sides nd ll locting bldes removed Pedestl with flnge cut wy on one side nd two locting bldes removed Pedestl with ll four locting bldes retined Hrmer Uni-Ring 1. All four optionl spcers hmmered down flush with ring t perimeter of enclosing wll or prpet. 2. Two optionl spcers hmmered down t junction of two slbs. 1 3. One optionl spcer hmmered down t junction of three slbs. 4. All four optionl spcers left upstnding t junction of four slbs. Hrmer Uni-Ring cn ccommodte vriety of pving slb thicknesses. The unit sizes, spnning cpcity nd loding of the slbs will determine the spcing nd lyout pttern of pving slb support system. 3 4 2 Hrmer Technicl Helpline +44 (0) 1744 648400 83
Modulock Rised Deck Supports - Appliction Detils Pving Slbs with Open Joints on Hrmer Modulock Pedestl Cement-bsed pving slbs with open drin joints Hrmer Modulock Pedestl deck support Rigid insultion nd wterproofing over concrete deck Sheet Decking on Hrmer Modulock Pedestl Continuous flexible sheet deck covering Floor deck screw-fixed to Hrmer Modulock Pedestl deck support heds Hrmer Modulock Pedestl deck support Concrete sub-bse Timber Slts on Bttens on Hrmer Modulock Pedestl Treted timber slts screwed to cross bttens Cross bttens mechniclly fixed to Hrmer Modulock deck support heds Hrmer Modulock Pedestl deck support Concrete sub-bse 84 www.hrmerdringe.co.uk
Modulock Rised Deck Supports - Appliction Detils Open Jointed Bords on Bttens on Hrmer Modulock Pedestl Treted timber bords screwed to cross bttens Cross bttens mechniclly fixed to Hrmer Modulock deck support heds Hrmer Modulock Pedestl deck support Concrete sub-bse Pving Slbs on Hrmer Modulock Uni-Ring Pving slbs Hrmer Modulock Uni-Ring pving support Rigid insultion Asphlt on isolting membrne Screed Concrete deck Hrmer Technicl Helpline +44 (0) 1744 648400 85