P83-6 Thyristors type P83 are of modern design with pressure contacts, high alumina ceramic insulator and cold-welding encapsulation. Designed for use in power electronic circuits and equipment under normal operating conditions. KEY PARAMETERS U DRM, U RRM I TSM du/dt* di/dt up to 14 V 6 A 96 A 1 V/ s 4 A/ s * maximum (non standard) value FEATURES all diffused design high current capabilities high surge current capabilities low turn-off time values guaranteed di/dt high rates voltages high du/dt low gate current interdigitated dynamic gate low thermal impedance tested according to IEC standards compact size and small weight APPLICATION High Frequency Inverters Induction Heating Inverters Uninterruptable Power Supplies Outline type code: JEDEC TO-2AC See package details for further information Designed for use in high power industrial and commercial electronic circuits and equipment where high currents are encoutered and high reliability is essential. 1/8
P83-6 ORDERING INFORMATION When ordering please refer to device code builder presented below. Please use the complete part number when ordering, quote or in any future correspondence relating to your order. P83-6- voltage class (hundreds of volts) This is standard device, with no dynamic parameters specified and standard accessory set. Please refer to Electrical Parameters if specific dynamic demands have to be met. Those information, as well as any other concerning non-standard accessories e.g. custom leads lenght or lead terminal connector type should be included in the order. ELECTRICAL PARAMETERS Voltage ratings Voltage class U DRM, U RRM U DSM, U RSM I DRM, I RRM V V ma 8 8 9 1 1 11 5 12 12 13 14 14 15 du/dt group codes du/dt Group code V/ s no specified value 5 32 6 5 7 1 2/8
P83-6 Electrical properties Average on-state current @ case temperature Parameter Unit Test conditions Value ) A 6 T c C 75 RMS on-state current I T(RMS) A 94 Surge current I TSM A =125 C, U R=,8U RRM, t p=1ms I 2 t value I 2 t ka 2 s 46 On-state voltage drop max. U TM V =25 C, I TM=15A 2, Treshold voltage U T(T) V 1,2 Slope resistance r T mω,52 Latching current I l ma =25 C, U D=12V 1 Holding current I H ma =25 C, U D=12V 3 Circuit commutated turn-off time t q s =125 C, I TM=25A, di R/dt=25A/ s, du/dt=2v/ s, U D=,67U DRM, U RM=1V 96 2 for voltage class up to 12 32 for voltage class 14 Turn-n time (typical) t on s I TM=1A, U DM=1V 4 Rate of rise of on-state currentrepetitive Critical rate of raise of off-state voltage di/dt A/ s =125 C, I TM=3, U D=,67U DRM, f=5hz, I GM=1A, di G/dt=1A/ s du/dt V/ s =125 C, U D=,67U DRM, 32 1 (see du/dt group codes) Gate current to trigger I GT ma =25 C, U D=12V 2 Gate voltage to trigger U GT V =25 C, U D=12V 3 Termal properties Thermal resistance, junction to case Thermal resistance, case to heatsink Parameter Unit Test conditions Value R thjc C/W two sided, DC,37 R thcs C/W two sided,2 Operating junction temperature min...max C -4...+125 Storage temperature T stg C -4...+125 Mechanical properties Parameter Unit Value Clamping force F M kn 12,... 14, Weight m g 26 4 3/8
P83-6 Package details For further package information, please contact Sales & Marketing Department. All dimensions in mm, unless stated otherwise. Do not scale. 4/8
9 o 12 o 18 o P83-6 CHARACTERISTICS P T(AV), [W] P T(AV), [W] 12 1 8 3 o 6 o 9 o 12 o 18 o 16 14 12 1 6 o 9 o o 18 12 o DC 6 8 3 o 4 6 4 2 Q 2 Q 1 2 3 4 5 6 7, [A] Power loss characteristics. Sinus wave form. 1 2 3 4 5 6 7 8 9 1, [A] Power loss characteristics. Square wave form. 13 T C, [ o C] 13 T C, [ o C] 12 12 11 11 1 Q 1 Q 9 9 8 3 o 6 o 8 3 o 6 o 7 6 1 2 3 4 5 6 7, [A] Case temperature ratings. Sinus wave form. 9 o 12 o 7 18 o DC 6 1 2 3 4 5 6 7 8 9 1, [A] Case temperature ratings. Square wave form. 5/8
P83-6 I TSM, [ka] U TM, V 1 5 9 =max 4 =max 8 U R =,8U RRM 3 7 2 6 5 1 4 1 1 1 Non-repetitive surge current rating n 1 1 1 I TM, A On-state characteristic Z th(t), o C/W,1,1,1,1,1,1 1 1 Transient thermal impedance t, s 6/8
P83-6 Frequency characteristics 7/8
6 i G, ma 5 P83-6 Gate characteristics 4 = -4 o C 3 2 = +125 o C = +25 o C 1 u G, V 1 2 3 4 5 U GD =,25V Gate characteristic. Possible trigger area. 6 i G, ma 5 4 = -4 o C 3 2 = +125 o C = +25 o C 1 u G, V 1 2 3 4 5 U GD =,25V Gate characteristic. Possible trigger area. 4 3 2 i G, A B U FGM = 2V I FGM = 4A P GM = 16W 1 R A u G, V 5 1 15 2 Gate characteristic. A - possible trigger area B - permitted gate pulse forcing area R - recommended gate drive load line HEATSINKS LAMINA S.I. has its own proprietary range of extruded aluminium heatsinks designed to optimise the performance of our semiconductors with natural and forced air flow. High efficiency water cooled copper heatsinks are also available. DEVICE CLAMPS Disc devices require the correct clamping force to ensure their best operation. LAMINA S.I. offers a wide selection of clamps to suit all of our manufactured devices. POWER ASSEMBLY CAPABILITY LAMINA S.I. provides a support for those customers requiring more than a basic semiconductor and offers precisely assembled Power Blocks according to factory or customer standards. 8/8