2.5V/3., High Bandwidth, Hot Insertion Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High Bandwidth (>400 MHz) Permits Hot Insertion. Rail-to-Rail, 3. or 2.5V ing 5V I/O Tolerant 2.5V Supply Voltage Operation Packaging (Pb-free & Green): 24-pin 50-mil wide plastic QSOP (Q) Description Pericom Semiconductor s PI3C3384 is a 2.5V or 3., high bandwidth 0-bit, 2-port bus switches designed with a low On- Resistance allowing inputs to be connected directly to outputs. The bus switch creates no additional propagational delay or additional ground bounce noise. The switches are turned ON by the Bus Enable (BE) input signal. Two bus enable signals are provided, one for each of the upper and lower five bits of the two 0-bit buses. Applications High Bandwidth Data switching Hot Docking Block Diagram Pin Configuration A0 B0 A4 A5 A9 BEA BEB B4 B5 B9 BEA B0 A0 A B B2 A2 A3 B3 B4 A4 2 3 4 5 6 7 8 9 0 2 24 23 22 2 20 9 8 7 6 5 4 3 VCC B9 A9 A8 B8 B7 A7 A6 B6 B5 A5 BEB Truth Table () Function BE A BE B B0-B4 B5-B9 Disconnect H H Hi-Z Hi-Z Connect L H A0-A4 Hi-Z Connect H L Hi-Z A5-A9 Connect L L A0-A4 A5-A9. High Voltage Level, X = Don't Care, L =- Low Voltage Level, Hi-Z = High Impedance Pin Description Pin Name BE A, BE B A0 - A9 B0 - B9 V CC Description Bus Enable Inputs (Active LOW) Bus A Bus B Ground Power
2.5V/3., High Bandwidth, Hot Insertion Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature... 65 C to +50 C Ambient Temperature with Power Applied... 40 C to +85 C Supply Voltage to Ground Potential (Input & V CC Only)... 0.5V to +4. Supply Voltage to Ground Potential (s & D/O Only)... 0.5V to +4. DC Input Voltage... 0.5V to +5.5V DC Current... 20mA Power Dissipation....0W Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. R ON On Resistance (3) DC Electrical Characteristics (Over Operating Range, T A = 40 C to +85 C, V CC = 3. ± 0%) Parameters Description Test Conditions () Min Typ. (2) Max Units V IH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 V V IL Input LOW Voltage Guaranteed Logic Low Level 0.5 0.8 I IH Input HIGH Current V CC = Max, V IN = V CC ± I IL Input LOW Current V CC = Max, V IN = ± I OZH High-Impedance Current 0 A, B V CC ± µa V IK Clamp Diode Voltage V CC = Min, I IN = 8mA 0.73.2 V I ON = 48mA or 64mA Ω V CC = Min, V IN = 0. 8 5 V CC = Min, V IN = 0. 5 7 I ON = 48mA or 64mA Capacitance (T A = 25 C, f = MHz) Parameters (4) Description Test Conditions Typ. Units CIN Input Capacitance 3.5 COFF A/B Capacitance, Off V IN = 5.0 pf CON A/B Capacitance, On 0.0. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3., TA = 25 C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 4. This parameter is determined by device characterization but is not production tested. 2
2.5V/3., High Bandwidth, Hot Insertion Power Supply Characteristics Parameters Description Test Conditions () Min. Typ. (2) Max. Units ICC DICC Quiescent Power Supply Current Supply Current per Input @ TTL HIGH V CC = Max, V IN = or V CC 260 500 µa V CC = Max, 750 V IN = 3. (3). For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3., +25 C ambient. 3. Per TTL driven input (control inputs only); A and B pins do not contribute to ICC. ing Characteristics over 3. Operating Range Parameters Description Conditions () Com. Units Min Max tplh Propogation Delay (2,3) 0.25 tphl Ax to Bx, Bx to Ax tpzh Bus Enable Time.5 6.5 ns tpzl tphz tplz Bus Disable Time R = 500-ohm.5 5.5 ing Characteristics over 2.5V Operating Range Parameters Description Conditions () Com. Units Min Max tplh Propogation Delay (2,3) 0.25 tphl Ax to Bx, Bx to Ax tpzh Bus Enable Time.5 9.8 ns tpzl tphz tplz Bus Disable Time R = 500-ohm.5 8.3. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 3
2.5V/3., High Bandwidth, Hot Insertion 4.0 V CC = 3. 3.V 2.9V 2.7V 2.5V 2. 3.8V 3. 3.4V 3.2V 3. 2.8V V OUT, (V) 2.0 0.0 0.0.0 2.0 3.0 4.0 5.0 V IN, (V) Voltage vs. Input Voltage over Various Supply Voltages Test Circuit Position Pulse Generator VIN RT VCC D.U.T. VOUT 500Ω 50pF CL 500Ω Open Test Disable LOW Enable LOW Disable HIGH Enable HIGH t PD Open Definitions: C L = Load capacitance (includes jig and probe capacitance) R T = Termination resistance (should be equal to Z OUT of the pulse generator) Enable and Disable Timing Control Input Normally Low Normally High Enable t PZL t PZH. Disable t PLZ t PZH. Input Control Enable = Low Input Control Device = High 2. Pulse Generator total pulses Rate.0 MHz; Z OUT 50-Ohms; tf, tr 2.5ns 0. 0. V OL V OH Propagation Delay Same Phase Input Transisiton Opposite Phase Input Transisiton t PLH t PLH t PHL t PHL V OH V OL 4
2.5V/3., High Bandwidth, Hot Insertion 24.50.57 3.8 3.99 Guage Plane 0.20 MIN..03 0.20 0.33 DOCUMENT CONTROL NO. PD - 203 REVISION: H DATE: 0/22/07.337.344 8.56 8.74.00 Detail A.06.035 0.4 0.89.04.04 REF 0-6.033 0.84.053.069.35.75 SEATING PLANE.05 x 45 0.38 Detail A.007.00 0.78.025 typical 0.635.02 0.203 0.305.004.00 0.0.228.244 5.79 6.20 X.XX X.XX DENOTES DIMENSIONS IN MILLIMETERS Pericom Semiconductor Corporation 3545 N. st Street, San Jose, CA 9534-800-435-2335 www.pericom.com ) Controlling dimensions in millimeters 2) Ref: JEDEC MO-37B/AE 3) Dimensions do not include mold flash, protrusions or gate burrs DESCRIPTION: 24-Pin, 50-Mil Wide, QSOP PACKAGE CODE: Q 07-0475 Ordering Information Ordering Code Package Code Package Description PI3C3384QE Q Pb-Free & Green, 24-pin QSOP. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. E = Pb-free and Green 3. Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation -800-435-2336 www.pericom.com 5