MANUAL SETTING TYPE RECK/RECL/RECM FEATURES mm square compact size Excellent click & switch feelings Long life of million cycles RoHS compliant PART NUMBER DESIGNATION R E C K 5-0 Series name With click Push switch function and shaft Single shaft without push switch Single shaft with push switch Double shaft with push switch Output interface Voltage Open collector Output A & B Resolution (P/R) 5 LIST OF PART NUMBERS Resolution Click Push switch function Shaft Output interface Part number 5 (P/R) With Click No Yes Single Shaft Double Shaft Voltage (PIN HEADER Type) Open Collector (SCOKET Type) RECM5-0 RECK5-0 A RECK5-05-B A RECL5-05-B The products indicated by A mark are manufactured upon receipt of order basis.
RECK/RECL/RECM STANDARD SPECIFICATIONS Electrical characteristics Mechanical characteristics Input voltage Input current DC5 ± 5 % 30 ma maximum Click torque 7.35 mn m ±.5 maximum (75 ± 5 gf cm) With click Output wave form Square wave Click number 5 Output phases A, B Shaft loading (Pull-push) 9. N maximum ( kgf) Resolution 5 operation force.45 ±.47 N (50 ± 50 gf) Phase difference of outputs A & B 90 ± 45 stroke 0.3 ± 0. mm Maximum frequency response 00 Hz Rotational life (Mechanical) million cycles Output signal Light source (High) 0 (Low) + 4.5 V minimum + 0.5 V maximum LED ing life Shaft loading (When mounting) Radial Axial million cycles 4.90 N maximum (500 gf).94 N maximum (300 gf) Net weight Approx. g characteristics Strength of tighten screw N m {0. kgf cm} maximum Maximum contact rating Contact resistance Note) Manual setting only. DC5 V, 0 ma Ω maximum Initial value Environmental characteristics Operating temp. range 0 ~ 50 C Storage temp. range Protection grade 0 ~ 80 C IP40 OUTPUT Click spot for 5P/R Output A Output B a b c a, b, c, d 00 s d Click spot CW The click spot is located somewhere outputs A & B are at Lo level.
RECK/RECL/RECM RELIABILITY TEST The output shall satisfy the criteria below after the following tests. Test item Test conditions Vibration Amplitude :.5 mm or 98. m/s (0 G) whichever is smaller. 0 ~ 500 Hz excursion 5 min/cycle, 8 cycles each for X, Z, directions. Shock High temperature exposure Low temperature exposure Humidity Thermal shock Power ON Power ON 3 times each in directions (X, Z) at 490 m/s (50 G), ms. 80 C 9 h 50 C 9 h 0 C 9 h (To be measured after leaving samples for h at normal temperature and humidity after the test.) 0 C 9 h C Relative humidity (To be measured after wiping out moisture and leaving samples for h at normal temperature and humidity after the test.) To be done 0 cycles with the following condition (To be measured after leaving samples for h at normal temperature and humidity after the test.) C C OUTLINE DIMENSIONS Unless otherwise specified, tolerance: ± 0.4 (Unit: mm) Single shaft and PIN HEADER Accessories M9P = 0.5-0.5 ± 0.5 5.5 ± 0. 3 0.5 MAX 4.5 3 M9 P = 0.75 9.4.9 0.5 4 4. Nut. Washer 9. 9. 4.9-0.5 5 4 3 5 -.54 PIN ( 7. ) ( 9.4 ) (. ) PIN HEADER : Made by IRISO ELECTRONICS CO., LTD 908B - - Z03 - PT 8. (Locking type) PIN ASSIGNMENT Pin No. Without switch With switch Power 0 (V) Power 0 (V) N C For switch 3 N C For switch 4 Output B Output B 5 Output A Output A Power 5V Power 5V OUTPUT CIRCUITRY AND RECEIVING CIRCUITRY 4.7k Output Circuitry Transistor RN707JE eqivalent Schmitt IC TC7W4FK eqivalent Vcc (5V) Output "A", "B" GND (OV) Receiving Circuitry
RECK/RECL/RECM OUTLINE DIMENSIONS Unless otherwise specified, tolerance: 0.4 (Unit: mm) Single shaft and SOCKET Accessories - 0.5 ( 7.4 ).35.5 0.5 MAX 4.9 5 4 3.54-3 4 4 M9P = 0.75.35 ±0.05 5. ( 3. ) (.9 ) ( 7.5 ) SOCKET (SAMTEC) CES-0-0-S-S M9 P = 0.75. Nut 9.4 0.5.9. Washer Double shaft and SOCKET Option 4.9 5 4 3-0.5.54.35 ±0.05-3 M9P = 0.75 4 4 5. 3.8 ±0.05.4 ( 9.5 ).35 ( 7.4 ).35.5 ( 3. ) 0.5 MAX (.9 ) ( 7.5 ) SOCKET (SAMTEC) CES-0-0-S-S. +0.5 0 3.05 ±0.08. 3.3 90 9. 0.8 ±0.05 3. ±0.5 Locking Ring OUTPUT CIRCUITRY AND RECEIVING CIRCUITRY PIN ASSIGNMENT Pin No. Function Power 0 (V) For switch 3 For switch 4 Output B 5 Output A Power +5 V Output Circuitry.k Receiving Circuitry Transistor RN707JE eqivalent Schmitt IC TC7W4FK eqivalent Vcc (5V) Output "A", "B" GND (OV)
RECK/RECL/RECM Option Available mounting on PC board with Snap-in Holder as an optional item separately. 5. 0 3.5 4-.8 3 3. - 0.5. ±0. 3 With Snap-in Holder 4-.8 0 0.3.4 0.3 5.8-0. 3 4 5-.54 5 PIN No..5.3.4 5-.54-0.8 Mounting hole dimentions Tolerance : ±0. Thickness : t =.