General Descripion GG64 is a primary side conrol SMPS wih an inegraed MOSFET. I feaures programmable cable drop compensaion and a peak curren compensaion funcion, PFM echnology, and a CV/CC conrol loop wih high reliabiliy and average efficiency. Wih he GG64, he opo-coupler and Y capacior, secondary feedback conrol, and he loop compensaion circui can be eliminaed o reduce cos. Oupu power range of he GG64 is 2~4W, and in his range, he oupu volage can be se hrough a feedback resisor, and he oupu curren also can be se hrough he peak curren sense resisor. Seing cable drop compensaion and peak curren compensaion are also opions for opimized oupu volage/curren regulaion. DIP-8A-3-2.54 Feaures Buil-in high volage MOSFET Primary side conrol Low sar-up curren Leading edge blanking Pulse-Frequency Modulaion (PFM) Overvolage proecion Undervolage lockou Over emperaure proecion Cycle by cycle curren limiing Open loop proecion Cable drop compensaion Peak curren compensaion Applicaions Mobile Charger Low Power Adapor Charger for MP3 and oher porable apparaus Sand-by power supply Golden Gae Inegraed Circuis, Inc. Page 1 of 9 REV: 1. 212.8.13
GG64 Block Diagram VCC UVLO Reference volage Bias curren Over volage proecion Open loop proecion Over emperaure proecion 5mV + - On conrol CC conrol TCC 2.1V + - Err Amp OSC CV conrol Tcv R Q DRV + - S LEB GND Pin Configuraion 1 8 GND VCC 2 3 SD6853 6 4 5 Pin Descripion Pin No Pin Name I/O Funcion descripion 1 I Peak curren sense pin 2 GND - Ground 3 VCC - Power supply 4 I Feedback volage inpu pin 5 I Cable drop compensaion resisor connec pin 6 I peak curren compensaion resisor connec pin 7 -- -- No pin 8 O pin of high volage MOSFET Golden Gae Inegraed Circuis, Inc. Page 2 of 9 REV: 1. 212.8.13
Absolue Maximum Raing (unless oherwise specified, T amb =25 C) Characerisics Symbol Raing Uni Supply volage V CC -.3~26 V Inernal volage reference V REF5V -.3~5.5 V Inpu volage V -3~3 V Inpu volage V -.3~8 V Inpu volage V -.3~8 V Inpu volage on oher pins V IN -.3~ 5.3 V Inpu curren I IN -1~1 ma -source breakdown volage BV DSS 65 V Gae-Source Volage V GS ±3 V Curren I D 1 A Curren Pulsed I DM 2.5 A Power Dissipaion P D 1.25 W Single Pulsed Avalanche Energy E AS 35 mj Operaing juncion Temperaure T J +16 C Operaing emperaure range T amb -2~85 C Sorage emperaure range T STG -4~125 C ESD(body mode) ESD 25 V Thermal Characerisics Characerisics Symbol Condiions Raing Uni Thermal Resisance, Juncion-o-Case R θjc 12 C/W Thermal Resisance, Juncion-o-Ambien R θja 74 C/W MOS Elecrical Characerisics (unless oherwise specified, Tamb=25 C) Characerisics Symbol Condiions Min Typ Max Uni -source breakdown volage B VDSS V GS =V, I D =5 A 65 -- -- V Saic -source on-sae resisance R DS(ON) V GS =1V, I D =.5A -- 9.6 11.5 Inpu Capaciance C iss -- 12 -- Oupu Capaciance C oss V GS =V, V DS =25V, f=1mhz -- 19 -- pf Reverse Transfer Capaciance C rss --.55 -- Turn-on Delay Time d(on) -- 5.8 -- Rise Time r -- 11 -- V DS =.5B VDSS, I D =25mA ns Turn-off Delay Time d(off) -- 8. -- Fall ime f -- 14.8 -- Golden Gae Inegraed Circuis, Inc. Page 3 of 9 REV: 1. 212.8.13
Elecrical Characerisics (unless oherwise specified, V CC =18V, T amb =25 C) Characerisics Symbol Condiions Min Typ Max Uni Supply Volage Sar-up curren I ST V CC =14V -- 3 1 µa Quiescen curren I OP 3 45 µa Sar hreshold volage V ST 15 16 17 V Shudown hreshold volage V SP 7. 8. 9. V Reference power supply V REF5V 4.75 5. 5.25 V VCC Overvolage proecion V CCOVP 24 25 26 V Feedback Enable urn on volage V EN 2 5 8 mv Over volage proecion V OVP 4.8 5. 5.2 V Loop open volage V BLANK -1.4-1.2-1. V Consan volage hreshold value V CV 2. 2.1 2.2 V Dynamic Characerisics Leading-edge blanking ime T LEB.3.6.9 µs CV loop conrol off ime T CVmin 1. 2.8 µs T CVmax V > V CV +.2V 12 18 24 ms Over volage recover ime T OVP 12 18 24 ms Curren Limi Peak curren deecing hreshold volage V PK I = 5 7 9 mv Peak curren compensaion I PK I =-1µA 2.2 2.5 2.8 ma Cable drop compensaion Cable drop compensaion volage V R =1k,D S=5% 18 2 22 mv Over Temperaure Proecion Over emperaure deecion T sd 125 14 -- C Over emperaure hyseresis T sdhys 2 35 55 C Golden Gae Inegraed Circuis, Inc. Page 4 of 9 REV: 1. 212.8.13
Funcional Descripion GG64 is an off-line SMPS conroller. I feaures a buil-in MOSFET, cable drop compensaion, and peak curren compensaion. CV/CC is obained based on oupu volage/curren conrolled hrough deecing he feedback volage of he auxiliary winding and peak curren of he primary winding. The whole operaing period consiss of peak curren deecion and feedback volage deecion. When he MOSFET is on, he primary curren is deeced by a sense resisor and he volage a pin is negaive, he load is powered by he oupu capacior and he oupu volage Vo decreases. When he primary curren exceeds he limi, he MOSFET is off and he volage a pin is deeced. The oupu capacior and he load are powered by a secondary curren and Vo increases. The ransisor is on again afer sopping for TCV and holding for TCC and hen i comes o peak curren deec again. Sar-up and under volage lockou A he beginning, he capacior conneced o pin V CC is charged via he sar resisor by he high volage DC bus and he circui sars o work if volage a V CC is 14.5V. The circui is powered by he sar resisor and he auxiliary winding for normal operaion. The whole conrol circui eners undervolage lockou if V CC is decreased o 6.5V, hen he capacior conneced o pin V CC is charged hrough he sar resisor and he IC only resars when V CC =14.5V. VCC V ST V SP ICC Sar-up Consan volage Consan curren Shor-circui proecion Powered by sarup resisor Powered by sar-up resisor and auxiliary winding Powered by sarup resisor 1. Peak curren deecion When V DRIVE =1, he MOSFET is on and he linearly increased primary curren is deeced by he sense resisor. When his curren increases o he hreshold value (peak value), he MOSFET is off and he driving volage V DRIVE =. There is a burr when he MOSFET is on, and he MOSFET will be off by error if is volage is up o he hreshold value V PK for he peak curren. So he leading edge blanking ime T LEB =.6 s is se o avoid his error. 2. Peak curren compensaion The deeced peak curren value will be increased following he inpu AC volage due o he off delay. The oupu curren is grealy affeced by he peak curren, herefore he volage regulaion is worse wihou peak curren compensaion. Peak curren compensaion is available in he GG64 hrough pin by AC inpu volage deecion. Wih he compensaion, he deeced peak curren is hold wih differen inpu AC volages for beer line regulaion. The hreshold value V PK =.7V is se by he circui, where his value can be adjused by R SEN. The peak curren compensaion abiliy is decided by R, he lower he resisance, he higher he compensaion. Golden Gae Inegraed Circuis, Inc. Page 5 of 9 REV: 1. 212.8.13
Vin R F1 L S2 I P L P L S1 I S + Vou R R F2 V CE R SEN 3. Feedback Volage Deecion When he MOSFET is off, he volage a pin is posiive and volage is sensed a 2/3 duraion of his posiive volage, his sensed volage is used for T CV conrol afer compared wih V CV, amplified, and held. CV is available by conrolling T CV. Wihou consideraion of volage drop on he cable and recifier diode, he equaion is shown as: V OUT n n S2 S1 RF2 R R T OFF1, T OFF2 and T ON are couned a he same ime which indicaes duraions of posiive volage, damping oscillaion and negaive volage respecively. Posiive volage indicaes here is curren delivered o he secondary side of ransformer, while negaive and damping oscillaion indicae here is no curren delivered o he secondary side of ransformer. The duy facor is expressed as: D S F1 F2 V CV TOFF1 TOFF1 T T T T ; OFF1 OFF2 ON Oupu curren, also he average curren in secondary winding: I OUT I SP T 2T OFF1 nd 2 S I PK ; I SP peak curren in secondary winding, I PK peak curren in primary winding, n urns raio of primary/secondary windings. Hence, wih consan peak curren, T OFF1 =T OFF2 +T ON is guaraneed for CC oupu. Golden Gae Inegraed Circuis, Inc. Page 6 of 9 REV: 1. 212.8.13
I SEN V DRIVE T OFF1 sample V CV T OFF2 T ON T CC T ON T CV 4. Cable Drop Compensaion In he acual design, he cable volage drop V CAB should be aken ino consideraion: V D is almos consan wih differen currens, and cable volage drop V CAB is proporional o oupu curren, and V CV is needed o be compensaed o ge beer volage regulaion. For cable compensaion, R is used for equivalen cable resisor and differen R is needed for differen cable. Vin R F1 L S2 C R R F2 I P Lp I S L S1 + Vou V CE R SEN 5. Over volage proecion The oupu is shudown if volage a exceeds he hreshold V OVP and if his sae is kep for 18ms, hen he circui resars. VDRIVE V OVP V CV T OVP Golden Gae Inegraed Circuis, Inc. Page 7 of 9 REV: 1. 212.8.13
6. Over Temperaure Proecion GG64 If he circui is over emperaure, he oupu is shu down o preven he circui from damage. The hyseresis of over emperaure proecion is used o avoid frequenly change beween normal and proecion modes. The over proecion hreshold value is 14 C and hyseresis value is abou 35 C. Hence, he circui is only funcions normally when he emperaure is 15 C below. 7. Open Loop Proecion When he MOSFET is on, if V >-1V, he loop is open and open loop proecion is acive o shudown he oupu, his is kep for 18ms and hen he circui resars. Typical Applicaion Circui Vin V OUT R ST R F2 R F1 R VCC Conrol IC MOS GND C R R SEN Noe: The circui and parameers are for reference only; please se he parameers of he real applicaion circui based on he acual esing. Ordering Informaion Par No Package Marking Maerial Packing GG64 DIP-8A-3-2.54 GG64 Pb free Tube GG64G DIP-8A-3-2.54 GG64G Pb free Tube Golden Gae Inegraed Circuis, Inc. Page 8 of 9 REV: 1. 212.8.13
Package Ouline DIP-8A-3-2.54 UNIT: mm 8 1.52TYP 5 6.35 1 2.54TYP 4 3.MIN 4.36MAX ±.3 7.62 TYP.25~.35 7.62~9.5 9.25±.3.5MIN.4~.55 MOS Devices Operaion Noes: Elecrosaic charges may exis in many hings. Please ake he following prevenive measures o preven effecively he MOS elecric circui as a resul of he damage which is caused by discharge: The operaor mus pu on wris srap which should be earhed o agains elecrosaic. Equipmen cases should be grounded. All ools used during assembly, including soldering ools and solder bahs, mus be grounded. MOS devices should be packed in anisaic/conducive conainers for ransporaion. Disclaimer: The informaion furnished in his daa shee is believed o be accurae and reliable. However, no responsibiliy is assumed by Golden Gae Inegraed Circuis (GGIC) for is use. GGIC reserves he righ o change circuiry and specificaions a any ime wihou noificaion o he cusomer. Golden Gae Inegraed Circuis reserves he righ o make changes o he informaion herein for he improvemen of he design and performance wihou furher noice! Cusomers should obain he laes relevan informaion before placing orders and should verify ha such informaion is complee and curren. All semiconducor producs malfuncion or fail wih some probabiliy under special condiions. When using Golden Gae Inegraed Circuis producs in sysem design or complee machine manufacuring, i is he responsibiliy of he buyer o comply wih he safey sandards sricly and ake essenial measures o avoid siuaions in which a malfuncion or failure of such Golden Gae Inegraed Circuis producs could cause loss of body injury or damage o propery. Golden Gae Inegraed Circuis (GGIC) Producs are no designed or auhorized for use as componens in life suppor appliances, devices or sysems where malfuncion of a produc can reasonably be expeced o resul in personal injury. Life suppor devices or sysems are devices or sysems ha (a) are inended for surgical implan ino he body or (b) suppor or susain life, and whose failure o perform can be reasonably expeced o resul in a significan injury o he user. A Purchaser's use or sale of GGIC Producs for use in life suppor appliances, devices or sysems is a Purchaser's own risk and Purchaser agrees o fully indemnify GGIC for any damages resuling from such use or sale. Golden Gae Inegraed Circuis, Inc. Page 9 of 9 REV: 1. 212.8.13