Report No R-RFCEP02V01-A. Test Report. Model No. MS-1223, MS-1331 Transmitter Module. MSI / MS Date of Receipt Apr.

Test Report Product Name Notebook Model No. MS-1223, MS-1331 Transmitter Module. MSI / MS-6890 Applicant Address MICRO-STAR INT L Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. Date of Receipt Apr. 16, 2008 Issued Date July 01, 2008 Report No. 084271R-RFCEP02V01-A Version V1.0 The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Page: 1 of 48

Test Report Certification Issued Date: July 01, 2008 Report No.: 084271R-RFCEP02V01-A Accredited by DNV, Nemko and NIST (NVLAP) Product Name Applicant Address Manufacturer Model No. Rated Voltage Working Voltage Trade Name Notebook MICRO-STAR INT L Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. MICRO-STAR INT L Co., LTD. MS-1223, MS-1331 AC 230V/50Hz AC 230V/50Hz MSI Applicable Standard ETSI EN 301 489-17:V1.2.1 (2002-08) ETSI EN 301 489-1: V1.6.1 (2005-09) Test Result Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : Tested By : (Senior Engineering Adm. Specialist / Anita Chou) ( Assistant Engineer / Dino Chen ) Approved By : ( Deputy Manager /Vincent Lin ) Page: 2 of 48

TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION...5 1.1. EUT Description...5 1.2. Tested System Details...7 1.3. Configuration of Test System...8 1.4. EUT Exercise Software...8 1.5. Test Facility...9 2. Conducted Emission...10 2.1. Test Equipmen...10 2.2. Test Setup...10 2.3. Limits...11 2.4. Test Procedure...12 2.5. Test Specification...12 2.6. Uncertainty...12 2.7. Test Result...12 3. Radiated Emission...13 3.1. Test Equipment...13 3.2. Test Setup...13 3.3. Limits...14 3.4. Test Procedure...14 3.5. Test Specification...14 3.6. Uncertainty...14 3.7. Test Result...14 4. Power Harmonics, Voltage Fluctuation and Flicker...15 4.1. Test Equipment...15 4.2. Test Setup...15 4.3. Limits...15 4.4. Test Procedure...16 4.5. Test Specification...16 4.6. Uncertainty...16 4.7. Test Result...16 5. Electrostatic Discharge (ESD)...17 5.1. Test Equipment...17 5.2. Test Setup...17 5.3. Test Level...17 5.4. Test Procedure...18 5.5. Test Specification...18 5.6. Uncertainty...18 5.7. Test Result...18 6. Radiated Susceptibility (RS)...19 6.1. Test Equipment...19 6.2. Test Setup...19 6.3. Test Level...19 6.4. Test Procedure...20 6.5. Test Specification...20 6.6. Uncertainty...20 6.7. Test Result...20 7. Electrical Fast Transient/Burst (EFT/B)...21 7.1. Test Equipment...21 Page: 3 of 48

7.2. Test Setup...21 7.3. Test Level...22 7.4. Test Procedure...22 7.5. Test Specification...22 7.6. Uncertainty...22 7.7. Test Result...22 8. Surge...23 8.1. Test Equipment...23 8.2. Test Setup...23 8.3. Test Level...23 8.4. Test Procedure...24 8.5. Test Specification...24 8.6. Uncertainty...24 8.7. Test Result...24 9. Conducted Susceptibility (CS)...25 9.1. Test Equipment...25 9.2. Test Setup...25 9.3. Test Level...25 9.4. Test Procedure...26 9.5. Test Specification...26 9.6. Uncertainty...26 9.7. Test Result...26 10. Voltage Dips and Interruption...27 10.1. Test Equipment...27 10.2. Test Setup...27 10.3. Test Level...27 10.4. Test Procedure...28 10.5. Test Specification...28 10.6. Uncertainty...28 10.7. Test Result...28 11. EMC Reduction Method During Compliance Testing...29 12. Test Result...30 12.1. Test Data of Conducted Emission...31 12.2. Test Data of Radiated Emission...37 12.3. Test Data of Power Harmonics, Voltage Flucturation and Flicker...38 12.4. Test Data of Electrostatic Discharge...41 12.5. Test Data of Radiated Susceptibility...42 12.6. Test Data of Electrical Fast Transient...43 12.7. Test Data of Surge...44 12.8. Test Data of Conducted Susceptibility...45 12.9. Test Data of Voltage Dips and Interruption...46 Attachment 1: EUT Test Photographs Attachment 2: EUT Detailed Photographs Page: 4 of 48

1. GENERAL INFORMATION 1.1. EUT Description Product Name Trade Name Model No. Working Voltage Frequency Range Antenna List Notebook MSI MS-1223, MS-1331 AC 230V/50Hz 2412-2472MHz, 5180-5320MHz and 5500-5700MHz Number of Channels 802.11b/g/n-20MHz/n-40MHz: 13, 802.11a/n-20MHz: 19 802.11n-40MHz: 4 Data Speed 802.11b: 11Mbps, 802.11a/g: 54Mbps, 802.11n: 300Mbps Channel separation 802.11b/g/n-20MHz: 5 MHz, 802.11a/n-20MHz: 20MHz 802.11n-40MHz: 40MHz Type of Modulation DSSS/OFDM Channel Control Auto Antenna Gain Refer to the table Antenna List Antenna type PIFA Power Adapter#1 MFR: LI SHIN, M/N: 0335A1965 Input: AC 100-240V, 50-60Hz 1.7A Output: DC 19V, 3.42A Cable out: Shielded, 1.7m with one ferrite core bonded. Power Adapter#2 MFR: DELTA, M/N: ADP-65HB BB Input: AC 100-240V, 50-60Hz 1.5A Output: DC 19V, 3.42A Cable out: Shielded, 1.7m with one ferrite core bonded. No. Manufacturer Part No. Peak Gain 1 VSO S79-1800570-V03 (Main) S79-1800580-V03 (Aux-L) S79-1800590-V03 (Aux-R) -0.21dBi for 2.4GHz 1.03dBi for 5GHz 2 VSO S79-1800580-V03 (Main-L) S79-1800590-V03 (Aux-R) S79-1800680-V03 (Aux) 1.00dBi for 2.4GHz 2.06dBi for 5GHz Page: 5 of 48

802.11b/g/n-20MHz Center Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 01: 2412 MHz Channel 02: 2417 MHz Channel 03: 2422 MHz Channel 04: 2427 MHz Channel 05: 2432 MHz Channel 06: 2437 MHz Channel 07: 2442 MHz Channel 08: 2447 MHz Channel 09: 2452 MHz Channel 10: 2457 MHz Channel 11: 2462 MHz Channel 12: 2467 MHz Channel 13: 2472 MHz 802.11a/n-20MHz Center Working Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 1: 5180 MHz Channel 2: 5200 MHz Channel 3: 5220 MHz Channel 4: 5240 MHz Channel 5: 5260 MHz Channel 6: 5280 MHz Channel 7: 5300 MHz Channel 8: 5320 MHz Channel 9: 5500 MHz Channel 10: 5520 MHz Channel 11: 5540 MHz Channel 12: 5560 MHz Channel 13: 5580 MHz Channel 14: 5600 MHz Channel 15: 5620 MHz Channel 16: 5640 MHz Channel 17: 5660 MHz Channel 18: 5680 MHz Channel 19: 5700 MHz 802.11n-40MHz Center Working Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 1: 5190 MHz Channel 2: 5310 MHz Channel 3: 5510 MHz Channel 4: 5670 MHz Note: 1. The EUT is including two models, The MS-1223 for 12 Panel and the MS-1331 for 13 Panel different marketing requirement. 2. QuieTek verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: EMI Mode EMS Mode Mode1: Normal Operation (MSI / MS-6890) Mode1: Normal Operation (MSI / MS-6890) Page: 6 of 48

1.2. Tested System Details The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord 1 TS-9980 R&S N/A N/A N/A 2 LCD Monitor CMV CT-730D FNC122F57BA1655 Non-Shielded, 1.8m 3 Printer EPSON StyLus C63 FAPY093590 Non-Shielded, 1.9m 4 Microphone & PCHOME N/A N/A N/A Earphone 5 TV VIZIO N/A N/A Non-Shielded, 1.8m 6 USB Mouse Logitech M-BE58 HCA30103299 N/A 7 IPod nano Apple A1199 7R649LBKVQ5 N/A 8 Notebook PC DELL PPT N/A Non-Shielded, 0.8m 9 Exchange Network Sun Moon Star PX-4 95170087 Non-Shielded, 1.8m Signal Cable Type Signal cable Description A LAN Cable Non-Shielded, 3.0m B D-SUB Cable Shielded, 1.8m, with two ferrite cores bonded C USB Cable Shielded, 1.5m D Earphone & Microphone Cable Non-Shielded, 1.5m E USB Cable Shielded, 1.5m F HDMI Cable Shielded, 1.0m G USB Cable Shielded, 1.5m H Telecom Cable Non-Shielded, 1.5m two PCS I Coaxial Cable Shielded, 1.8m Page: 7 of 48

1.3. Configuration of Test System 1.4. EUT Exercise Software (1) Setup the EUT and peripherals as shown in section 1.3. (2) Turn on the power of all equipments. (3) Boot the EUT. (4) The EUT reads test software from the hard disk. The EUT, the monitor, and the notebook will show the transmitting and receiving characteristics when (5) the communication is success. (6) The wireless LAN function is used to perform the wireless data transmission. (7) Repeat the step 5 and 6. Page: 8 of 48

1.5. Test Facility Ambient conditions in the laboratory: Items Test Item Required (IEC 68-1) Actual Temperature ( C) 15-35 20-35 Humidity (%RH) IEC 61000-4-2 30-60 50-55 Barometric pressure (mbar) 860-1060 950-1000 Temperature ( C) 15-35 20-35 Humidity (%RH) IEC 61000-4-5 10-75 50-65 Barometric pressure (mbar) 860-1060 950-1000 Temperature ( C) IEC 61000-4-4 15-35 20-35 Barometric pressure (mbar) IEC 61000-4-11 860-1060 950-1000 Site Description: Accredited by NVLAP NVLAP Lab Code: 200533-0 Accredited by DNV Statement No. : 413-99-LAB11 Accredited by Nemko Certificate No.: ELA 165 Accredited by TUV Rheinland Certificate No.: 10011438-1-2007 Site Name: Site Address: Quietek Corporation No. 5-22, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : service@quietek.com Page: 9 of 48

2. Conducted Emission 2.1. Test Equipmen The following test equipment are used during the conducted emission test: Item Equipment Manufacturer Model No. / Serial No. Last Cal. Remark 1 Test Receiver R & S ESCS 30 / 825442/018 Sep., 2007 2 Artificial Mains Network R & S ENV4200 / 848411/10 Feb., 2008 Peripherals 3 LISN R & S ESH3-Z5 / 825562/002 Feb., 2008 EUT 4 Pulse Limiter R & S ESH3-Z2 / 357.8810.52 Feb., 2008 5 4-wire ISN R & S ENY41 / 837032/001 Feb., 2008 6 Double 2-Wire ISN R & S ENY22 / 835354/008 Feb., 2008 7 No.1 Shielded Room Note: All equipment upon which need to calibrated are with calibration period of 1 year. 2.2. Test Setup Shielded Room 0.8m Peripheral ( EUT ) 40cm 80cm AMN for Peripheral AMN for EUT 50 ohm Terminator Test Receiver Page: 10 of 48

2.3. Limits (1) Mains terminal Frequency MHz Limits (dbuv) Limit for conducted emissions of equipment intended to be used in Limit for conducted emissions telecommunication centers only QP AV QP AV 0.15-0.50 79 66 66-56 56-46 0.50-5.0 73 60 56 46 5.0-30 73 60 60 50 Remarks: The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz ~ 0.50 MHz. (2) Telecommunication ports Limits (dbuv) Frequency MHz Limit for conducted emissions from telecommunication ports of equipment intended for use in telecommunication centers only Limit for conducted emissions from telecommunication ports QP AV QP AV 0.15 0.50 97-87 84-74 84-74 74-64 5.0 30 87 74 74 64 Remarks: In the above table, the tighter limit applies at the band edges. Page: 11 of 48

2.4. Test Procedure AC Mains: The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm /50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of AC line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ETSI EN 301489-1: V1.6.1 (2005-09) on conducted measurement. The bandwidth of the field strength meter (R & S Test Receiver ESCS 30) is set at 9kHz. Telecommunication Port: The mains voltage shall be supplied to the EUT via the LISN when the measurement of telecommunication port is performed. The common mode disturbances at the telecommunication port shall be connected to the ISN, which is 150ohm impedance. Both alternative cables are tested related to the LCL requested. The measurement range is from 150kHz to 30MHz. The bandwidth of measurement is set to 9kHz. The 60dB LCL ISN is used for cat. 5 cable, 50dB LCL ISN is used for cat. 3 and 80dB LCL is wed for alternative one. 2.5. Test Specification According to ETSI EN 301489-1: V1.6.1 (2005-09) EN 55022: 2006 2.6. Uncertainty ± 2.26 db 2.7. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 12 of 48

3. Radiated Emission 3.1. Test Equipment The following test equipment are used during the Radiated emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 1 Test Receiver R & S ESVS 10 / 834468/003 July, 2008 Spectrum Analyzer Advantest R3162/ 00803480 May, 2008 Pre-Amplifier Advantest BB525C/ 3307A01812 May, 2008 Bilog Antenna SCHAFFNER CBL6112B / 2697 Nov., 2007 Site # 2 Test Receiver R & S ESCS 30 / 836858 / 022 Nov., 2007 Spectrum Analyzer Advantest R3162 / 100803466 May, 2008 Pre-Amplifier Advantest BB525C/3307A01814 May, 2008 Bilog Antenna SCHAFFNER CBL6112B / 2705 Oct., 2007 Horn Antenna ETS 3115 / 0005-6160 July, 2008 Pre-Amplifier QTK QTK-AMP-01/ 0001 July, 2008 Site # 3 Test Receiver R & S ESI 26 / 838786 / 004 May, 2008 Spectrum Analyzer Advantest R3162 / 100803480 May, 2008 Pre-Amplifier QTK QTK-AMP-03 / 0003 May, 2008 Bilog Antenna SCHAFFNER CBL6112B / 2697 May, 2008 Horn Antenna ETS 3115 / 0005-6160 July, 2008 Pre-Amplifier QTK QTK-AMP-01 / 0001 July, 2008 Note: 1. All equipments are calibrated every one year. 2. The test instruments marked by X are used to measure the final test results. 3.2. Test Setup 10m FRP Dome 1m to 4m Non-Conducted Table Load EUT Antenna Mast Dipole or Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m 80cm Test Receiver Fully Soldered Ground Plane TO Controller To Receiver Page: 13 of 48

3.3. Limits Limits (dbuv/m) Frequency MHz Limit for radiated emissions from ancillary equipment intended for use in telecommunication centers only, and measured on a stand alone basis QP Limit for radiated emissions from ancillary equipment, measured on a stand alone basis QP 30-230 40 30 230-1000 47 37 3.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 10 meters.the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ETSI 301489-1: V1.6.1 (2005-09) on radiated measurement. The additional motch filter below 1GHz was used to measure the level of harmonics radiated emission during field dtrength of harmonics measurement. The bandwidth below 1GHz setting on the field strength meter (R&S Test Receiver ESCS 30 )is 120 khz, and 1MHz bandwidth is adpted above 1GHz. The frequency range from 30MHz to 10 th harmonics is checked. 3.5. Test Specification According to ETSI EN 301489-1: V1.6.1 (2005-09) EN 55022: 2006 3.6. Uncertainty ± 3.8 db 3.7. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 14 of 48

4. Power Harmonics, Voltage Fluctuation and Flicker 4.1. Test Equipment Item Instrument 4Manufacturer Type No/Serial No. Last Calibration 1 Power Harmonics Tester SCHAFFNER Profline 2105-400 S/N: HK54148 June, 2008 2 Analyzer SCHAFFNER CCN 1000-1/X71887 June, 2008 3 No.3 Shielded Room Note: All equipments are calibrated every one year. 4.2. Test Setup Controller PC Power Analyzer Impedance Network Power Source EUT Load Non-Conducted 4.3. Limits Limits of Class A Harmonics Currents Harmonics Order n Maximum Permissible harmonic current A Odd harmonics Harmonics Order n Maximum Permissible harmonic current A Even harmonics 3 2.30 2 1.08 5 1.14 4 0.43 7 0.77 6 0.30 9 0.40 8 n 40 0.23 * 8/n 11 0.33 13 0.21 15 n 39 0.15 * 15/n Limits of Class B Harmonics Currents For Class B equipment, the harmonic of the input current shall not exceed the maximum permissible values given in table that is the limit of Class A multiplied by a factor of 1.5. Page: 15 of 48

Limits of Class C Harmonics Currents Report No. 084271R-RFCEP02V01-A Harmonics Order Maximum Permissible harmonic current Expressed as a percentage of the input current at the fundamental frequency n % 2 2 3 30.λ * 5 10 7 7 9 5 11 n 39 3 (odd harmonics only) *λ is the circuit power factor Limits of Class D Harmonics Currents Harmonics Order Maximum Permissible harmonic current per watt ma/w Maximum Permissible harmonic current A n 3 3.4 2.30 5 1.9 1.14 7 1.0 0.77 9 0.5 0.40 11 0.35 0.33 13 n 39 (odd harmonics only) 4.4. Test Procedure 3.85/n See limit of Class A The EUT is supplied in series with power analyzer from a power source having the same normal voltage and frequency as the rated supply voltage and the equipment under test. And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be performed. 4.5. Test Specification According to EN 61000-3-2:2006, EN 61000-3-3:1995+A1: 2001+A2: 2005 4.6. Uncertainty ± 3.23 % 4.7. Test Result The measurement of the power harmonics, which test at the extremes of EUT s supply range, was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Test Result: (See Test Result) PASS FAIL Note: According to clause 7 of EN 61000-3-2: 2006, equipment with a rated power of 75W or less, no limits apply. The test result is only for reference. Page: 16 of 48

5. Electrostatic Discharge (ESD) 5.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 ESD Simulator System SCHAFFNER NSG-438 S/N: 167 June, 2008 2 Horizontal Coupling Plane (HCP) 3 Vertical Coupling Plane (VCP) 4 No.3 Shielded Room QuieTek HCP AL50 N/A QuieTek VCP AL50 N/A Note: All equipments are calibrated every one year. 5.2. Test Setup Vertical Coupling Plane Insulation EUT Loads: Active Horizontal Coupling Plane 80cm Non-Conducted table ESD Simulator 470K ohm Resistor Metal Ground Plane 470K ohm Resistor 5.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Enclosure Port Electrostatic Discharge kv(charge Voltage) ±8 Air Discharge ±4 Contact Discharge B Page: 17 of 48

5.4. Test Procedure Direct application of discharges to the EUT: Contact discharge was applied only to conductive surfaces of the EUT. Air discharges were applied only to non-conductive surfaces of the EUT. During the test, it was performed with single discharges. For the single discharge time between successive single discharges will be keep longer 1 second. It was at least ten single discharges with positive and negative at the same selected point. The selected point, which was performed with electrostatic discharge, was marked on the red label of the EUT. Indirect application of discharges to the EUT: Vertical Coupling Plane (VCP): The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned at a distance 0.1m from, the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point. Horizontal Coupling Plane (HCP): The coupling plane is placed under to the EUT. The generator shall be positioned vertically at a distance of 0.1m from the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point. 5.5. Test Specification According to EN 61000-4-2:1995+A1: 1998+A2: 2001 5.6. Uncertainty ± 6.003 % 5.7. Test Result The measurement of the electrostatic discharge was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 18 of 48

6. Radiated Susceptibility (RS) 6.1. Test Equipment Item Equipment Manufacturer Model No. / Serial No. Last Cal. 1 Signal Generator R & S SMY02 / 825454/029 Oct., 2007 2 Power Amplifier A & R 100W10000M7 / A285000010 N/A 3 RF Power Amplifier OPHIRRF 5022F / 1075 N/A 4 Bilog Antenna Chase CBL6112B / 2452 Sep., 2007 5 Power Meter R & S NRVD / 100219 Jan., 2008 6 Directional Coupler A & R DC6180 / 22735 Jan., 2008 7 No.5 EMC Fully Chamber Note: All equipments are calibrated every one year. 6.2. Test Setup Antenna Mast 3 m Sensor Full-Anechoic Chamber Camera system EUT Load 1m 80cm Power Amplifier Field Meter Power Meter Signal Generator Computer controller Camera Monitor 6.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Enclosure Port Radio-Frequency MHz 80-1000 1400-2000 Electromagnetic Field V/m(Un-modulated, rms) 3 A Amplitude Modulated % AM (1kHz) 80 Page: 19 of 48

6.4. Test Procedure The EUT and load, which are placed on a table that is 0.8 meter above ground, are placed with one coincident with the calibration plane such that the distance from antenna to the EUT was 3 meters. Both horizontal and vertical polarization of the antenna and four sides of the EUT are set on measurement. In order to judge the EUT performance, a CCD camera is used to monitor EUT screen. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 3 V/m Level 2 2. Radiated Signal AM 80% Modulated with 1kHz sinusoidal audio signal 3. Scanning Frequency 80MHz - 1000MHz, 1400MHz - 2000MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 6.5. Test Specification According to EN 61000-4-3 Edition 3.0: 2006 6.6. Uncertainty ± 6.17 % 6.7. Test Result The measurement of the radiated susceptibility was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 20 of 48

7. Electrical Fast Transient/Burst (EFT/B) 7.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration Fast Transient/Burst 1 Generator 2 No.2 Shielded Room SCHAFFNER NSG 2050 S/N: 200124-031AR June, 2008 Note: All equipments are calibrated every one year. 7.2. Test Setup Page: 21 of 48

7.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Ports for signal lines and control lines kv (Peak) +0.5 Fast Transients Common Mode Tr/Th ns 5/50 B Rep. Frequency khz 5 Input DC Power Ports kv (Peak) +0.5 Fast Transients Common Mode Tr/Th ns 5/50 B Rep. Frequency khz 5 Input AC Power Ports kv (Peak) +1 Fast Transients Common Mode Tr/Th ns 5/50 B Rep. Frequency khz 5 7.4. Test Procedure The EUT and load are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. For Signal Ports and Telecommunication Ports: The EFT interference signal is through a coupling clamp device couples to the signal and control lines of the EUT with burst noise for 1min. For Input DC and AC Power Ports: The EUT is connected to the power mains through a coupling device that directly couples the EFT interference signal. Each of the Line and Neutral conductors is impressed with burst noise for 1 min. The length of power cord between the coupling device and the EUT shall be 1m. 7.5. Test Specification According to EN 61000-4-4:1995+A1: 2001+A2: 2001 7.6. Uncertainty ± 8.80 % 7.7. Test Result The measurement of the Electrical Fast Transient/Burst was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 22 of 48

8. Surge 8.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Surge Generator SCHAFFNER NSG 2050 S/N: 200124-031AR 2 No.6 Shielded Room June, 2008 Note: All equipment upon which need to calibrated are with calibration period of 1 year. 8.2. Test Setup PC Surge Generator EUT Load Non-Conducted Table Non-Conducted Table 8.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Telecommunication Ports (See 1) and 2)) Surges Tr/Th us Line to Ground kv Telecommunication Ports in Telecom Centres (See 1) and 2)) Surges Tr/Th us Line to Ground kv AC Input and AC Output Power Ports Surges Line to Line Line to Ground Tr/Th us kv kv AC Input and AC Output Power Ports in Telecom Centres Surges Tr/Th us Line to Line kv Line to Ground kv 1.2/50 (8/20) ± 1 1.2/50 (8/20) ± 0.5 1.2/50 (8/20) ±1 ± 2 1.2/50 (8/20) ±0.5 ± 1 B B B B Notes: 1) Applicable only to ports which according to the manufacturer s may directly to outdoor cables. 2) Where normal functioning cannot be achieved because of the impact of the CDN on the EUT, no immunity test shall be required. Page: 23 of 48

8.4. Test Procedure The EUT and its load are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The length of power cord between the coupling device and the EUT shall be 2m or less. For Signal Ports and Telecommunication Ports The disturbance signal is through a coupling and decoupling networks (CDN) device couples to the signal and Telecommunication lines of the EUT. For Input and Output AC Power or DC Input and DC Output Power Ports: The EUT is connected to the power mains through a coupling device that directly couples the Surge interference signal. The surge noise shall be applied synchronized to the voltage phase at 0 0, 90 0, 180 0, 270 0 and the peak value of the a.c. voltage wave. (Positive and negative) Each of Line-Earth and Line-Line is impressed with a sequence of five surge voltages with interval of 1 min. 8.5. Test Specification According to EN 61000-4-5 Edition 2.0: 2005 8.6. Uncertainty ± 7.93 % 8.7. Test Result The measurement of the Surge was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 24 of 48

9. Conducted Susceptibility (CS) 9.1. Test Equipment Item Equipment Manufacturer Model No. / Serial No. Last Cal. 1 CS SYSTEM SCHAFFNER NSG 2070 March, 2008 2 CDN SCHAFFNER CDN M016S / 20822 Dec., 2007 3 CDN SCHAFFNER CDN M016S / 20823 Dec., 2007 4 FIXED PAD SCHAFFNER INA 2070-1 / 2115 N/A 5 EM Clamp KEMZ 801 / 21024 March, 2008 6 No.6 Shielded Room Note: All equipments are calibrated every one year. 9.2. Test Setup Aux equipment CDN EUT CDN Aux equipment Ground Reference Plane T Non-Conducted Table T2 RF-Generator PA 9.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria AC Input and AC Output & DC Input and DC output Power Ports & Functional Earth Ports Radio-Frequency Common Mode. Amplitude Modulated MHz V (rms, Unmodulated) % AM (1kHz) Source Impedance Ω 0.15-80 3 80 150 A Page: 25 of 48

9.4. Test Procedure The EUT are placed on a table that is 0.8 meter height, and a Ground reference plane on the table, EUT are placed upon table and use a 10cm insulation between the EUT and Ground reference plane. For Signal Ports and Telecommunication Ports The disturbance signal is through a coupling and decoupling networks (CDN) or EM-clamp device couples to the signal and Telecommunication lines of the EUT. For Input DC and AC Power Ports The EUT is connected to the power mains through a coupling and decoupling networks for power supply lines. And directly couples the disturbances signal into EUT. Used CDN-M2 for two wires or CDN-M3 for three wires. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 130dBuV(3V) Level 2 2. Radiated Signal AM 80% Modulated with 1kHz sinusoidal audio signal 3. Scanning Frequency 0.15MHz 80MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 9.5. Test Specification According to EN 61000-4-6 Edition 2.2: 2006 9.6. Uncertainty ± 6.17 % 9.7. Test Result The measurement of the Conducted Susceptibility was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 26 of 48

10. Voltage Dips and Interruption 10.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Voltage Dips Generator SCHAFFNER NSG 2050 S/N: 200124-031AR 2 No.6 Shielded Room June, 2008 Note: All equipments are calibrated every one year. 10.2. Test Setup To AC Line Voltage Dips/ Interruptions /Variations Simulator AC Power Line to EUT EUT Load Non-Conducted Table 80cm Controller Computer Printer 10.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria AC Input and AC Output Power Ports Voltage Dips % Reduction ms 30 10 B Voltage Dips % Reduction ms 60 100 C Voltage Interruptions % Reduction ms > 95 % 5000 C Page: 27 of 48

10.4. Test Procedure The EUT and its load are placed on a table which is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The power cord shall be used the shortest power cord as specified by the manufacturer. For Voltage Dips/ Interruptions test: The selection of test voltage is based on the rated power range. If the operation range is large than 20% of lower power range, both end of specified voltage shall be tested. Otherwise, the typical voltage specification is selected as test voltage. The EUT is connected to the power mains through a coupling device that directly couples to the Voltage Dips and Interruption Generator. The EUT shall be tested for 30% voltage dip of supplied voltage and duration 10ms, with a sequence of three voltage dips with intervals of 10 seconds, for 60% voltage dip of supplied voltage and duration 100ms with a sequence of three voltage dips with intervals of 10 seconds, and for 95% voltage interruption of supplied voltage and duration 5000ms with a sequence of three voltage interruptions with intervals of 10 seconds. Voltage phase shifting are shall occur at 0 0, 45 0, 90 0,135 0,180 0,225 0, 270 0,315 0 of the voltage. 10.5. Test Specification According to EN 61000-4-11:1994+A1: 2001 10.6. Uncertainty ± 2.03 % 10.7. Test Result The measurement of the Voltage Dips and Interruption was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 28 of 48

11. EMC Reduction Method During Compliance Testing No modification was made during testing. Page: 29 of 48

12. Test Result The test results in the emission and the immunity were performed according to the requirements of measurement standard and process. Quietek Corporation is assumed full responsibility for the accuracy and completeness of these measurements. The test data of the emission is listed as below. All the tests were carried out with the EUT in normal operation, which was defined as: EMI Mode EMS Mode Mode1: Normal Operation (MSI / MS-6890) Mode1: Normal Operation (MSI / MS-6890) Page: 30 of 48

12.1. Test Data of Conducted Emission Product : Notebook Test Item : Conducted Emission Test Site : No.1 Shielded Room Power Line : Line 1 Test Mode : Mode1: Normal Operation (MSI / MS-6890) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv LINE 1 Quasi-Peak 0.201 0.643 52.390 53.033-11.510 64.543 0.537 0.300 42.380 42.680-13.320 56.000 1.064 0.320 40.680 41.000-15.000 56.000 1.865 0.340 35.470 35.810-20.190 56.000 3.939 0.400 26.950 27.350-28.650 56.000 25.806 1.200 24.650 25.850-34.150 60.000 Average 0.201 0.643 50.550 51.193-3.350 54.543 0.537 0.300 36.720 37.020-8.980 46.000 1.064 0.320 40.670 40.990-5.010 46.000 1.865 0.340 31.880 32.220-13.780 46.000 3.939 0.400 20.080 20.480-25.520 46.000 25.806 1.200 19.160 20.360-29.640 50.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 31 of 48

Product : Notebook Test Item : Conducted Emission Test Site : No.1 Shielded Room Power Line : Line 2 Test Mode : Mode1: Normal Operation (MSI / MS-6890) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv LINE 2 Quasi-Peak 0.197 0.300 51.570 51.870-12.787 64.657 0.466 0.310 42.720 43.030-13.941 56.971 1.064 0.320 40.400 40.720-15.280 56.000 3.341 0.380 29.340 29.720-26.280 56.000 8.841 0.480 26.880 27.360-32.640 60.000 25.380 1.090 26.250 27.340-32.660 60.000 Average 0.197 0.300 49.940 50.240-4.417 54.657 0.466 0.310 34.770 35.080-11.891 46.971 1.064 0.320 35.290 35.610-10.390 46.000 3.341 0.380 23.710 24.090-21.910 46.000 8.841 0.480 18.910 19.390-30.610 50.000 25.380 1.090 20.780 21.870-28.130 50.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 32 of 48

Product : Notebook Test Item : Impedance Stabilization Network Test Site : No.1 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) (ISN-100Mbps) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv Quasi-Peak 0.865 9.900 46.410 56.310-17.690 74.000 1.400 9.900 45.430 55.330-18.670 74.000 1.732 9.910 44.440 54.350-19.650 74.000 13.357 10.020 47.400 57.420-16.580 74.000 18.244 9.990 50.380 60.370-13.630 74.000 23.127 9.970 52.900 62.870-11.130 74.000 Average 0.865 9.900 43.560 53.460-10.540 64.000 1.400 9.900 43.850 53.750-10.250 64.000 1.732 9.910 42.370 52.280-11.720 64.000 13.357 10.020 45.240 55.260-8.740 64.000 18.244 9.990 47.190 57.180-6.820 64.000 23.127 9.970 49.580 59.550-4.450 64.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 33 of 48

Product : Notebook Test Item : Impedance Stabilization Network Test Site : No.1 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) (ISN-10Mbps) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv Quasi-Peak 0.865 9.900 46.510 56.410-17.590 74.000 1.396 9.900 44.400 54.300-19.700 74.000 1.728 9.910 44.940 54.850-19.150 74.000 5.017 9.880 32.240 42.120-31.880 74.000 10.002 9.850 60.960 70.810-3.190 74.000 15.005 10.010 29.840 39.850-34.150 74.000 Average 0.865 9.900 44.010 53.910-10.090 64.000 1.396 9.900 41.140 51.040-12.960 64.000 1.728 9.910 39.230 49.140-14.860 64.000 5.017 9.880 11.200 21.080-42.920 64.000 10.002 9.850 45.240 55.090-8.910 64.000 15.005 10.010 13.760 23.770-40.230 64.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 34 of 48

Product : Notebook Test Item : Impedance Stabilization Network Test Site : No.1 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) (ISN-GIGA) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv Quasi-Peak 0.265 10.162 50.420 60.582-20.132 80.714 0.599 10.090 47.560 57.650-16.350 74.000 0.865 10.070 49.150 59.220-14.780 74.000 1.466 10.040 46.780 56.820-17.180 74.000 1.732 10.020 46.160 56.180-17.820 74.000 2.138 10.010 47.070 57.080-16.920 74.000 Average 0.265 10.162 47.120 57.282-13.432 70.714 0.599 10.090 47.210 57.300-6.700 64.000 0.865 10.070 47.190 57.260-6.740 64.000 1.466 10.040 45.530 55.570-8.430 64.000 1.732 10.020 43.420 53.440-10.560 64.000 2.138 10.010 45.590 55.600-8.400 64.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 35 of 48

Product : Notebook Test Item : Impedance Stabilization Network Test Site : No.1 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) (ISN-Telecom) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv Quasi-Peak 0.576 9.950 47.500 57.450-16.550 74.000 1.462 9.930 48.380 58.310-15.690 74.000 1.736 9.920 52.190 62.110-11.890 74.000 2.205 9.920 46.180 56.100-17.900 74.000 7.591 9.890 35.810 45.700-28.300 74.000 28.560 10.040 24.980 35.020-38.980 74.000 Average 0.576 9.950 46.240 56.190-7.810 64.000 1.462 9.930 42.260 52.190-11.810 64.000 1.736 9.920 49.520 59.440-4.560 64.000 2.205 9.920 36.510 46.430-17.570 64.000 7.591 9.890 35.800 45.690-18.310 64.000 28.560 10.040 11.860 21.900-42.100 64.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 36 of 48

12.2. Test Data of Radiated Emission Product : Notebook Test Item : General Radiated Emission Test Site : No.3 OATS Test Mode : Mode1: Normal Operation (MSI / MS-6890) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv/m db dbuv/m Horizontal 45.500 10.961 12.700 23.660-6.340 30.000 137.950 13.329 6.420 19.749-10.251 30.000 157.850 12.122 7.580 19.702-10.298 30.000 250.000 15.293 14.000 29.293-7.707 37.000 566.780 24.004 9.100 33.104-3.896 37.000 921.000 28.195 3.200 31.394-5.606 37.000 Vertical 165.000 11.899 9.300 21.199-8.801 30.000 250.000 15.293 11.500 26.793-10.207 37.000 336.000 17.908 8.000 25.908-11.092 37.000 624.000 24.634 9.000 33.634-3.366 37.000 816.000 27.120 3.600 30.720-6.280 37.000 921.000 28.195 2.900 31.094-5.906 37.000 Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 37 of 48

12.3. Test Data of Power Harmonics, Voltage Flucturation and Flicker Product : Notebook Test Item : Power Harmonics Classification : Class D Test Mode : Mode1: Normal Operation (MSI / MS-6890) Test Result: Pass Source qualification: Normal Current & voltage waveforms 6 300 Current (Amps) 4 2 0-2 -4 200 100 0-100 -200 Voltage (Volts) -6-300 Harmonics and Class D limit line European Limits Current RMS(Amps) 0.225 0.200 0.175 0.150 0.125 0.100 0.075 0.050 0.025 0.000 4 8 12 16 20 24 28 32 36 40 Harmonic # Test result: Pass Worst harmonic was #17 with 0.00% of the limit. Page: 38 of 48

Test Result: Pass Source qualification: Normal THC(A): 0.00 I-THD(%): 0.00 POHC(A): 0.000 POHC Limit(A): 0.000 Highest parameter values during test: V_RMS (Volts): 229.70 Frequency(Hz): 50.00 I_Peak (Amps): 3.271 I_RMS (Amps): 0.539 I_Fund (Amps): 0.183 Crest Factor: 6.742 Power (Watts): 46.5 Power Factor: 0.375 Harm# Harms(avg) 100%Limit %of Limit Harms(max) 150%Limit %of Limit Status 2 0.006 3 0.169 0.158 0.0 0.177 0.227 0.00 Pass 4 0.007 5 0.164 0.088 0.0 0.171 0.127 0.00 Pass 6 0.007 7 0.157 0.046 0.0 0.163 0.067 0.00 Pass 8 0.007 9 0.147 0.023 0.0 0.153 0.033 0.00 Pass 10 0.007 11 0.136 0.016 0.0 0.141 0.023 0.00 Pass 12 0.007 13 0.124 0.014 0.0 0.128 0.020 0.00 Pass 14 0.007 15 0.111 0.012 0.0 0.114 0.017 0.00 Pass 16 0.007 17 0.097 0.011 0.0 0.100 0.015 0.00 Pass 18 0.007 19 0.083 0.009 0.0 0.086 0.014 0.00 Pass 20 0.006 21 0.070 0.009 0.0 0.072 0.012 0.00 Pass 22 0.006 23 0.057 0.008 0.0 0.058 0.011 0.00 Pass 24 0.005 25 0.045 0.007 0.0 0.046 0.010 0.00 Pass 26 0.004 27 0.034 0.007 0.0 0.035 0.009 0.00 Pass 28 0.003 29 0.025 0.006 0.0 0.026 0.009 0.00 Pass 30 0.003 31 0.016 0.006 0.0 0.018 0.008 0.00 Pass 32 0.002 33 0.010 0.005 0.0 0.011 0.008 0.00 Pass 34 0.001 35 0.005 0.005 0.0 0.005 0.007 0.00 Pass 36 0.001 37 0.002 0.005 0.0 0.002 0.007 0.00 Pass 38 0.001 39 0.003 0.005 0.0 0.004 0.006 0.00 Pass 40 0.001 1.Dynamic limits were applied for this test. The highest harmonics values in the above table may not occur at the same window as the maximum harmonics/limit ratio. 2:According to EN61000-3-2 paragraph 7 the note 1 and 2 are valid for all applications having an active input power >75W. Others the result should be pass. Page: 39 of 48

Product : Notebook Test Item : Voltage Fluctuations and Flicker Test Mode : Mode1: Normal Operation (MSI / MS-6890) Test Result: Pass Status: Test Completed Pst i and limit line European Limits 1.00 0.75 Pst 0.50 0.25 18:55:56 Plt and limit line 0.50 Plt 0.25 18:55:56 Parameter values recorded during the test: Vrms at the end of test (Volt): 229.59 Highest dt (%): 0.00 Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (ms): 500.0 Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): 0.00 Test limit (%): 4.00 Pass Highest Pst (10 min. period): 0.160 Test limit: 1.000 Pass Highest Plt (2 hr. period): 0.070 Test limit: 0.650 Pass Page: 40 of 48

12.4. Test Data of Electrostatic Discharge Product : Notebook Test Item : Electrostatic Discharge Test Site : No.3 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) Item Amount of Discharge Voltage Required Criteria Complied To Criteria (A, B, C) Results Air Discharge 10 10 +8kV -8kV B B A A Pass Pass Contact Discharge 25 25 +4kV -4kV B B A A Pass Pass Indirect Discharge 50 +4kV B A Pass (HCP) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Front) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Left) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Back) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Right) 50-4kV B A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv. No false alarms or other malfunctions were observed during or after the test. Page: 41 of 48

12.5. Test Data of Radiated Susceptibility Product : Notebook Test Item : Radiated Susceptibility Test Site : No.5 EMC fully Chamber Test Mode : Mode1: Normal Operation (MSI / MS-6890) Frequency (MHz) Position (Angle) Polarity (H or V) Field Strength (V/m) Required Criteria Complied To Criteria (A, B, C) Results 80-1000 Front H 3 A A Pass 80-1000 Front V 3 A A Pass 80-1000 Back H 3 A A Pass 80-1000 Back V 3 A A Pass 80-1000 Left H 3 A A Pass 80-1000 Left V 3 A A Pass 80-1000 Right H 3 A A Pass 80-1000 Right V 3 A A Pass 80-1000 Top H 3 A A Pass 80-1000 Top V 3 A A Pass 80-1000 Down H 3 A A Pass 80-1000 Down V 3 A A Pass 1400-2000 Front H 3 A A Pass 1400-2000 Front V 3 A A Pass 1400-2000 Back H 3 A A Pass 1400-2000 Back V 3 A A Pass 1400-2000 Left H 3 A A Pass 1400-2000 Left V 3 A A Pass 1400-2000 Right H 3 A A Pass 1400-2000 Right V 3 A A Pass 1400-2000 Top H 3 A A Pass 1400-2000 Top V 3 A A Pass 1400-2000 Down H 3 A A Pass 1400-2000 Down V 3 A A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at at frequency MHz. No false alarms or other malfunctions were observed during or after the test. V/m Page: 42 of 48

12.6. Test Data of Electrical Fast Transient Product : Notebook Test Item : Electrical Fast Transient Test Site : No.2 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) Inject Line Polarity Voltage (kv) Inject Time (Second) Inject Method Required Criteria Complied to Criteria Result L+N+PE ± 1kV 60 Direct B B PASS LAN ± 0.5kV 60 Direct B B PASS Telecom ± 0.5kV 60 Direct B B PASS Coaxial ± 0.5kV 60 Direct B B PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page: 43 of 48

12.7. Test Data of Surge Product : Notebook Test Item : Surge Test Site : No. 6 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) Inject Line Polarity Angle Voltage (kv) Time Interval (Second) Inject Method Required Criteria Complied to Criteria Result L-N ± 0 1 60 Direct B B Pass L-N ± 90 1 60 Direct B B Pass L-N ± 180 1 60 Direct B B Pass L-N ± 270 1 60 Direct B B Pass N-PE ± 0 2 60 Direct B B Pass N-PE ± 90 2 60 Direct B B Pass N-PE ± 180 2 60 Direct B B Pass N-PE ± 270 2 60 Direct B B Pass L+PE ± 0 2 60 Direct B B Pass L+PE ± 90 2 60 Direct B B Pass L+PE ± 180 2 60 Direct B B Pass L+PE ± 270 2 60 Direct B B Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page: 44 of 48

12.8. Test Data of Conducted Susceptibility Product : Notebook Test Item : Conducted Susceptibility Test Site : No. 6 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) Frequency Voltage Inject Tested Port of Required Performance Result Range Applied Method EUT Criteria Criteria (MHz) dbuv(v) Complied To 0.15~80 130 (3V) CDN AC IN A A PASS 0.15~80 130 (3V) CDN LAN A A PASS 0.15~80 130 (3V) CDN GIGA LAN A A PASS 0.15~80 130 (3V) CDN Telecom A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 45 of 48

12.9. Test Data of Voltage Dips and Interruption Product : Notebook Test Item : Voltage Dips and Interruption Test Site : No.6 Shielded Room Test Mode : Mode1: Normal Operation (MSI / MS-6890) Voltage Dips and Interruption Reduction (%) Angle Test Duration (ms) Required Performance Criteria Performance Criteria Complied To Test Result 30 0 10 B B PASS 30 45 10 B B PASS 30 90 10 B B PASS 30 135 10 B B PASS 30 180 10 B B PASS 30 225 10 B B PASS 30 270 10 B B PASS 30 315 10 B B PASS 60 0 100 C B PASS 60 45 100 C B PASS 60 90 100 C B PASS 60 135 100 C B PASS 60 180 100 C B PASS 60 225 100 C B PASS 60 270 100 C B PASS 60 315 100 C B PASS >95 0 5000 C B PASS >95 45 5000 C B PASS >95 90 5000 C B PASS >95 135 5000 C B PASS >95 180 5000 C B PASS >95 225 5000 C B PASS >95 270 5000 C B PASS >95 315 5000 C B PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 46 of 48

Attachment 1: EUT Test Photographs Page: 47 of 48

Report No.: 084271R-RFCEP02V01-A Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Page : 1 of 8

Report No.: 084271R-RFCEP02V01-A Front View of Conducted Test (ISN) Back View of Conducted Test (ISN) Page : 2 of 8

Report No.: 084271R-RFCEP02V01-A Front View of Radiated Test Back View of Radiated Test-Clamp Page : 3 of 8

Report No.: 084271R-RFCEP02V01-A Power Harmonics Test Setup ESD Test Setup Page : 4 of 8

Report No.: 084271R-RFCEP02V01-A Radiated Susceptibility Test Setup EFT/B Test Setup Page : 5 of 8

Report No.: 084271R-RFCEP02V01-A EFT/B Test Setup Clamp SURGE Test Setup Page : 6 of 8

Report No.: 084271R-RFCEP02V01-A Conducted Susceptibility Test Setup Conducted Susceptibility Test Setup- CDN Page : 7 of 8

Report No.: 084271R-RFCEP02V01-A Voltage Dips Test Setup Page : 8 of 8

Attachment 2: EUT Detailed Photographs Page: 48 of 48

Report No.: 084271R-RFCEP02V01-A Attachment 2 : EUT Detailed Photographs (1) EUT Photo (MS-1223) (2) EUT Photo Page : 1 of 10