WLS8- UV LED Strip Light Datasheet Banner's WLS8- UV LED Strip Lights have sturdy aluminum housings, shatterproof windows, and impressive environmental ratings, making them a cost-effective operator inspection light or machine vision light to improve and enhance contrast in UV fluorescent and non-fluorescent applications. UV 65 nm and 95 nm wavelength models available for diverse applications Low-profile, space-saving design Rugged, water-resistant IP69K option Available in four lengths from 85 to 0 mm Lensed models available on UV95 models Daisy chain power to multiple lights Safe for long-term worker operation Optional snap clips for easy installation and repositioning Capability to dim lights using the wiring pinout (Hi/Lo/Off) Optional switch is now Hi/Lo/Off Automatic temperature protection built into the unit. Above 50 C, the light dims to manage heat and protect product lifetime PWM models can be used for strobed operation NOTE: When cascading lights, a model with an ON/OFF switch can be used to control the lights cascaded off the switched model. Stand-Alone Light cable Stand-Alone Light or End Light in a Cascade QD First Light in a Cascade cable First or Middle of a Cascade QD These Work Light Strips are available as either stand-alone models, or as cascade models that can be "daisy-chained" together for a continuous length of lighting, with a minimum of wiring. Stand-alone models have cable or male quick disconnect (QD) at one end for power connection and no connections at opposite end. A stand-alone model may be used as the last in the cascade series. Cascade models have cable or male quick disconnect (QD) at one end for power connection and a female quick disconnect (QD) at the opposite end for connecting to other lights in the cascade. Cascade models with cable end can only be used as the first light in the cascade series. A double-ended accessory cordset must be used between each pair of lights in a cascade. Family WLS8- UV Wavelength Lighted Length (mm) Cascadable Window Construction Control Connector C UV95 85 X Q C = Cascadable X = Non-cascadable 85 570 850 * 0 * X = Not sealed * S = Sealed Blank = m integral cable Q = Integral -pin M QD UV65 = 65 nm UV95 = 95 nm Blank = Clear acrylic (UV95 models) G = Clear glass (UV65 models) L5 = 5 deg lensed window (UV95 models) Blank = None PB = High/Lo/Off Switch * PWM = Pulse Width Modulation Dimming * Not available in UV65 models Sealed models not available with Hi/Lo/Off Original Document 899 Rev. B November 05 899
WLS8- UV LED Strip Light Table : IEC IP50 Models Non-Switch Models HIGH/OFF/LOW Switch Models PWM Models Stand-Alone Cascade Stand-Alone Cascade Stand-Alone Cascade Lighted Length Wavelength WLS8-XUV95-85X WLS8-CUV95-85X WLS8-XUV95-85XPB WLS8-CUV95-8 5XPB WLS8-XUV95-85XPWM WLS8-CUV95-8 5XPWM 85 mm WLS8-XUV95-570X WLS8-XUV95-850X WLS8-CUV95-570X WLS8-CUV95-850X WLS8-XUV95-5 70XPB WLS8-XUV95-8 50XPB WLS8-CUV95-57 0XPB WLS8-CUV95-85 0XPB WLS8-XUV95-570XPWM WLS8-XUV95-850XPWM WLS8-CUV95-57 0XPWM WLS8-CUV95-85 0XPWM 570 mm 850 mm 95 nm WLS8-XUV95-0X WLS8-CUV95-0X WLS8-XUV95-0XPB WLS8-CUV95-0XPB WLS8-XUV95-0XPWM WLS8-CUV95-0XPWM 0 mm Only the integral meter cabled power connector models are listed. To order the -pin M/Euro-style integral power connector model, add suffix Q to the model number (for example, WLS8-XUV95-85XQ). Table : IEC IP67/IP69K Models Non-Switch Models PWM Models Stand-Alone Cascade Stand-Alone Cascade Lighted Length Wavelength WLS8-XUV65-85GS WLS8-CUV65-85GS WLS8-XUV65-85GSPWM WLS8-CUV65-85GSPWM 85 mm WLS8-XUV65-570GS WLS8-CUV65-570GS WLS8-XUV65-570GSPWM WLS8-CUV65-570GSPWM 570 mm 65 nm WLS8-XUV95-85S WLS8-CUV95-85S WLS8-XUV95-85SPWM WLS8-CUV95-85SPWM 85 mm WLS8-XUV95-570S WLS8-CUV95-570S WLS8-XUV95-570SPWM WLS8-CUV95-570SPWM 570 mm WLS8-XUV95-850S WLS8-CUV95-850S WLS8-XUV95-850SPWM WLS8-CUV95-850SPWM 850 mm 95 nm WLS8-XUV95-0S WLS8-CUV95-0S WLS8-XUV95-0SPWM WLS8-CUV95-0SPWM 0 mm Only the integral meter cabled power connector models are listed. To order the -pin M/Euro-style integral power connector model, add suffix Q to the model number (for example, WLS8-XUV65-85GSQ). Wiring Diagram Male Female Pin Wire Color Connection brown to 0 V dc blue dc common black Models without the switch or PWM: Connect to to 0 V dc for 50% maximum intensity Models with PWM: Connect to 8 to 0 V dc to turn the light off; connect to dc common or leave floating to turn the light on. white Not used For maximum intensity, leave the black wire floating or connected to common. Specifications Operating Voltage to 0 V dc Use only with suitable Class power supply (UL) or a SELV power supply (CE). www.bannerengineering.com - Tel: +-76-5-6 P/N 899 Rev. B
WLS8- UV LED Strip Light Table : Typical Current Light Length Typical Current Max. Current Radiant Flux (mw) (Typical at 5 C) V dc V dc 0 V dc A UV65 UV95 85 mm 0.66 A 0.0 A 0. A 0.8 50 850 570 mm.6 A 0.6 A 0.8 A.6 500 700 850 mm. A 0.9 A 0.7 A. - 550 0 mm.0 A. A 0.97 A. - 00 Supply Protection Circuitry Protected against reverse polarity and transient voltages Light Characteristics UV65: 60 70 nm UV95: 90 00 nm LED Lifetime Lumen Maintenance - L 70 When operating within specifications, output will decrease less than 0% after 0,000 hours. Push Button II = 00% light intensity I = 50% light intensity 0 = Off Pulse Width Modulation (PWM) Frequency: Up to 000 Hz Voltage: 8 to 0 V dc Current: ma maximum per foot Construction Clear anodized aluminum housing; painted zinc end caps; zinc plated steel brackets Window for UV65 models: tempered borosilicate glass Window for UV95 models: acrylic Mounting () swivel brackets SMBWLS8RA included and () screws Connections Integral -pin M male quick disconnect (QD) (-pin connecting cordset required); or m (6.5 ft) integral cable Environmental Rating IEC IP50 (non-sealed models) or IEC IP67/IP69K per DIN 0050 (sealed models) Vibration and Mechanical Shock Vibration 0 to 55 Hz.0 mm p-p amplitude per IEC60068--6 Shock 5G ms duration, half sine wave per IEC60068--7 Operating Temperature 0 C to +70 C ( 0 F to +58 F) Light output begins to decrease above 50 C ( F) and will be approximately 65% of max intensity at 60 C (0 F) and 0% of max intensity at 70 C (58 F) Storage Temperature 0 C to +70 C ( 0 F to +58 F) Certifications Application Note When connecting cascadable lights in series at 00% intensity, it is important not to exceed maximum current limitations: Maximum length of light at V dc:. m (.6 ft) Maximum length of light at V dc:.0 m (9.8 ft) Maximum length of light at 0 V dc:. m (0. ft) At 50% intensity, double the lengths. NOTE: Do not spray cable with highpressure sprayer, or cable damage will result. NOTE: This product emits UV light. Exempt Risk Group (RG 0) product. No optical hazard is considered reasonably foreseeable, even for continuous, unrestricted use (IEC 67). Dimensions L5 Models [.55] 8 [.0] 8 [.]. [.7] [.8].5 [.5] 8 [.0] 9.5 [.7] 9 [.75] 0 [.8] Motion Detector Models ON/OFF Switch Models ø 5 [.0].5 [.5].0 [.8] 6.9 [.5] ø.7 [.58] 0.8 [.8] X M X.50 ISO 7.5 [.0] 0.5 [.].5 [.] 0 [.8] 0.8 [.8] P/N 899 Rev. B www.bannerengineering.com - Tel: +-76-5-6
WLS8- UV LED Strip Light Dimensions are shown with the included SMBWLS8RA bracket. Non-Switch Models IP50 Models IP67/IP69K Models L L L L WLS8-..85X WLS8-..85S 6 mm (. in) 6 mm (.6 in) 86 mm (.6 in) 6 mm (. in) WLS8-..570X WLS8-..570S 6 mm (5. in) 68 mm (.7 in) 568 mm (.6 in) 598 mm (.5 in) WLS8-..850X WLS8-..850S 96 mm (6.5 in) 90 mm (5.8 in) 850 mm (.6 in) 880 mm (.6 in) WLS8-..0X WLS8-..0S 08 mm (7.6 in) 9 mm (6.9 in) mm (.57 in) 6 mm (5.7 in) ON/OFF Switch Models Model L L L L WLS8-..85XPB 9 mm (5. in) 76 mm (.8 in) 86 mm (.6 in) 6 mm (.6 in) WLS8-..570XPB 67 mm (6.5 in) 658 mm (5.9 in) 568 mm (.6 in) 68 mm (.7 in) WLS8-..850XPB 956 mm (7.6 in) 90 mm (7 in) 850 mm (.6 in) 90 mm (5.8 in) WLS8-..0XPB 8 mm (8.7 in) mm (8. in) mm (.57 in) 9 mm (6.9 in) Accessories Cordsets Use single-ended cordsets between the power source and the QD connection of a stand-alone light or the first light in a cascade. Use double-ended cordsets between lights in a cascade. -Pin Threaded M/Euro-Style Cordsets Model Length Style Dimensions Pinout (Female) MQDC-06.8 m (6 ft) Typ. MQDC-5 MQDC-0 MQDC-50 MQDC-06RA MQDC-5RA MQDC-0RA MQDC-50RA.57 m (5 ft) 9. m (0 ft) 5. m (50 ft).8 m (6 ft).57 m (5 ft) 9. m (0 ft) 5. m (50 ft) Straight Right-Angle M x ø.5 [0.57"] Typ. [.6"] M x ø.5 0 Typ. [.8"] = Brown = White = Blue = Black www.bannerengineering.com - Tel: +-76-5-6 P/N 899 Rev. B
WLS8- UV LED Strip Light -Pin Threaded M/Euro-Style Cordsets Double Ended Model Length Style Dimensions Pinout MQDEC-0SS 0. m ( ft) Female MQDEC-0SS MQDEC-06SS MQDEC-SS 0.9 m ( ft).8 m (6 ft).66 m ( ft) 0 Typ. [.58"] MQDEC-0SS MQDEC-0SS MQDEC-50SS 6.0 m (0 ft) 9. m (0 ft) 5. m (50 ft) Male Straight/ Female Straight M x ø.5 [0.57"] Typ. [.7"] M x ø.5 [0.57"] Male = Brown = White = Blue = Black -Pin Threaded M/Euro-Style Splitter Cordsets Flat Junction Model Branches (Female) Trunk (Male) Pinout CSB-M0M0 No branch No trunk Female CSB-M0M CSB-MM CSB-M8M CSB-M5M CSB-M5M x 0.0 m ( ft) No trunk 0.0 m ( ft).50 m (8 ft).57 m (5 ft) 7.60 m (5 ft) Male CSB-UNT5M 0 Typ. [.58"] Ø.5 [0.8"] 8.0 [0.7"] 7.60 m (5 ft) Unterminated Typ. [.7"] Ø.5 [0.57"] Ø.5 [0.57"] M x 5 [.8"].0 [.69"] M x = Brown = White = Blue = Black P/N 899 Rev. B www.bannerengineering.com - Tel: +-76-5-6 5
WLS8- UV LED Strip Light Brackets SMBWLS8RA The bracket kit is available as a replacement for the one that comes with the Work Light Strip. The kit contains two end brackets and four screws. SMBWLS8SM This kit allows the light to be mounted at a right angle to the mounting surface. The kit contains two end brackets and four screws. SMBWLS8SP Stainless steel snap bracket kit Includes two brackets SMH6 This kit allows the light to be mounted to a /6-inch Unistrut channel. The kit includes: #0- spring nuts (qty ) #0- socket head cap screws (qty ) #0 lock washers (qty ) SMBWLSMAG Magnetic mounting bracket for easy attachment to steel surfaces SMBWLSMAGR Protective cover also available to prevent scratches to painted surfaces 6 www.bannerengineering.com - Tel: +-76-5-6 P/N 899 Rev. B
WLS8- UV LED Strip Light Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. www.bannerengineering.com - Tel: +-76-5-6