ACCESSORY FITMENT LIST These are all the accessories you will need to complete the assembly of your product. The following accessories are supplied in a pack and should be checked before attempting assembly Item G7 Qty 1 Item D4 Qty 2 M10 x 55 mm Allen Bolt Item D5 Qty 2 Item E13 Qty 4 M10 Flat Washer Item B18 Qty 4 M8 x 30 mm Allen Bolt (Black) Item C4 Qty 2 M8 x 16 mm Allen Bolt (Black) Item G13 Qty 2 M8 x 16 mm Allen Bolt Item G14 Qty 1 M5 x 10 mm Screw M4 x 12 mm Screw Page 14
Orbit Fitness, AU Unit 3, 470 Scarborough Beach Road, Osborne Park, Western Australia 6017 Carefully unpack each component, checking against the parts list that you have all the necessary parts to complete the assembly of your product. Please note that some of the parts may be pre-fitted to major components, so please check carefully before contacting our CUSTOMER SUPPORT team. In any event, please do not return the product to your retailer before contacting us first. Tel:- 1300 134 213 Fax:- (+618) 9445 9133 E-mail: service@orbitfitness.com.au CUSTOMER SUPPORT is open from 8.00am to 4.00pm from Monday to Friday 1 Loosen the M8 Allen Bolt and remove the packing reinforcement. Note Do NOT FULLY TIGHTEN any Bolts, Nuts or Fittings at this stage unless specifically instructed to do so. Page 15
2 Attach Flywheel Upper Cover (G7) to Flywheel Cover R (G3). G3 G7 3 Attach the Main frame Assembly (A1) to the Front Stabiliser (D1) with 2 x M10 x 55mm Allen Bolts (D4) and 2 x M10 Flat Washers (D5). A1 D4 D5 D1 Page 16
4 Attach the Seat (B12) to the Seat Carriage (B2) with 4 x M8 x 16mm Allen Bolts (B18, black). B18 B2 B12 5 Attach the Rear Stabiliser (C1) to the Aluminum Rail (B1) with 2 x M8 x 16mm Allen Bolts (C4). C4 C1 B1 Page 17
Assembly 6 Insert the Aluminum Rail (B1) into the Main Frame Assembly (A1). B1 A1 7 Align the Footplate (E1) to Aluminum Rail (B1) along with Main Frame and secure in position with 4 x M8 x 30mm Allen bolts (E13, black). B1 E1 E13 Page 18
8 Fix the Middle Cover R (G11R) and L (G11L) by 2 x M5 x 10mm Screws (G13) and 1 x M4 x 12mm Screw (G14). Note FULLY TIGHTEN all Bolts, Nuts and Fittings now, ensuring that your product in located on a clear flat surface before doing so. Your product will now be ready to use. G13 G14 G11L G13 G11R 9 If the Monitor Stand is loose, take 8mm Allen Wrench to adjust the turning hinge location bolt, which is accessible through the Flywheel Cover L (G4). Page 19
When you have finished your routine, be sure to set the Row Grip in its rest on the Handlebar Holder to partially release the tension on the Drive Strap, Return Spring and other internal components when your HURRICANE R2i is not in use. OPERATING ADJUSTMENTS and GENERAL USER INFORMATION Notice about Adjustment of Slide Mechanism (B7) There are 3pieces of Allen Bolts (B22 1 & B21 2) as the diagram shown under the Slide Mechanism (B7). Loosen the middle Allen Bolt (B22) first and adjust the other 2 pieces of Allen Bolts (B21) to be loose or tight depending personally. Finally, tighten the middle Allen Bolt (B22). B21 B22 B21 Note In the interest of safety, do NOT use polish or any lubricant on the seat, foam handgrips or footplates. B7 6mm Allen Wrench Page 20
B15 G9 Aa9 A16 Aa15 G4 G7 Aa8 G3 A40 Aa1 G2 A22 E7 D5 E8 A22 Aa2 E4 E6 E1 Aa11 Aa10 G12 E5 A22 E8 A12 Aa18 G9 G6 E9 Aa12 G5 A2 Aa4 G10 A35 Aa14 A37 D2 A30 A38 E13 A39 Aa3 G1 A37 E3 D1 A8 G13 E2 E12 E11 G14 A27 A29 D4 E10 G11L D5 F6 A46 A8 A9 A43 H3L A18 F2R G8 F4 H2 A10 Aa1 A6 A25 A34 H3R A13 Aa16 Aa13 F2L A19 Aa5 F1 A1 Aa6 F3 A39 A3 F5 A38 A16 A11 A4 A17 A36 Aa11 Aa17 Aa7 I1 B23 A31 B16 A16 A17 A41 A20 G11R A45 G13 A32 A44 A33L A14 H1 A15 A41 D5 Aa15 A16 B15 G8 A40 G8 B15 A33R A32 B1 B18 B2 A34 A12 A21 A42 C2 C4 A17 B7 C1 A17 B15 B6 B18 B20 B10 B5 B3 B24 B4 B17 C3 B14 B12 A28 B17 A7 A22 A23 A19 A26 F6 A24 B8 B21 B21 B22 B13 B10 B11 B20 B9 Assembly Page 21
MASTER PARTS & ACCESSORY LIST PART No. DESCRIPTION QTY A1 MAIN FRAME ASSEMBLY....... 1 A2 ALUMINUM FRAME COVER..... 1 A3 FLYWHEEL AXLE............. 1 A4 DRIVE BELT................. 1 A6 STEEL CABLE................ 1 A7 MAGNET BRACKET............ 1 A8 BEARING (6004ZZTPX)......... 2 A9 BUSHING................... 1 A10 S20 RETAINING RING.......... 1 A11 SMALL BELT PULLEY.......... 1 A12 PULLEY AXLE................ 1 A13 ALUMINUM PLATE............ 3 A14 FLYWHEEL.................. 1 A15 FAN WHEEL................. 1 A16 M6 FLAT WASHER............ 4 A17 M6 x 12mm ALLEN BOLT....... 10 A18 M6 x 25mm SCREW.......... 6 A19 M8 NYLON NUT.............. 2 A20 M6 NUT.................... A21 M8 x 55mm SCREW.......... 6 1 A22 M4 NUT.................... 11 A23 M4 NYLON NUT.............. 1 A24 M8 NUT.................... 1 A25 HANDLEBAR HOLDER......... 1 A26 M6 NYLON NUT.............. 1 A27 M6 x 110mm ALLEN BOLT...... 1 A28 M4 x 30mm ALLEN BOLT....... 1 A29 M6 x 50mm ALLEN BOLT....... 2 A30 5/32 x 1/2 SCREW............ 2 A31 HANDLEBAR................ 1 A32 HANDLEBAR FOAM GRIP....... 2 A33L HANDLEBAR COVER (L)........ 1 A33R HANDLEBAR COVER (R)........ 1 A34 HANDLEBAR END CAP......... 2 A35 PULLEY.................... 1 A36 BUSHING................... 1 A37 RETAINING RING FOR R22...... 2 A38 BEARING (608ZZTPX)......... 2 A39 BUSHING................... 2 A40 M10 x 25mm ALLEN BOLT...... 4 A41 M6 FLAT WASHER............ 6 A42 MAGNET PLATE.............. 2 A43 M20 NUT................... 1 A44 M5 x 16mm ALLEN BOLT....... 2 A45 TENSION CONTROLLER KNOB... 1 A46 M5 x 6mm ALLEN BOLT........ 1 Aa1 ADJUSTABLE PULLEY PLATE.... 2 Aa2 BELT PULLEY................ 1 Aa3 PULLEY.................... 1 Aa4 BELT...................... 1 Aa5 SPRING CASE............... 1 Aa6 SPIRAL SPRING.............. 1 Aa7 SPRING CASE COVER......... 1 Aa8 PULLEY AXLE................ 1 Aa9 BEARING (6201ZZ)........... 2 Aa10 M16 HEX NUT............... 1 Aa11 BEARING (HK-2012).......... 2 Aa12 BUSHING................... 1 Aa13 STEEL WASHER.............. 1 Aa14 ONE WAY BEARING (FC-2016)... 1 Aa15 M6 x 12mm SCREW...........2 Aa16 M5 x 8mm NUT.............. 3 Aa17 1/8 x 1/2 SCREW............. 4 Aa18 MAGNET................... 6 B1 ALUMINUM RAIL............. 1 B2 SEAT CARRIAGE............. 1 B3 ALUMINUM RAIL FIX PLATE..... 1 Page 22
MASTER PARTS & ACCESSORY LIST PART No. DESCRIPTION QTY B4 NUT PLATE................. 2 B5 STOP BLOCK................ 2 B6 RAIL END CAP FIX PLATE....... 1 B7 SLIDE MECHANISM........... 1 B8 RAIL END CAP............... 1 B9 UPPER SLIDE WHEEL......... 2 B10 SLIDE WHEEL............... 4 B11 WHEEL AXLE................ 1 B12 SEAT...................... 1 B13 M5x35mm ALLEN BOLT....... 1 B14 SEAT STOP................. 4 B15 M5 x 6mm SCREW........... 5 B16 M6 x 20mm ALLEN BOLT....... 2 B17 M8 x 40mm ALLEN BOLT....... 4 B18 M8 x 16mm ALLEN BOLT....... 4 B20 M5 x 10mm ALLEN BOLT....... 6 B21 M6 x 25mm ALLEN BOLT....... 2 B22 M6 x 20mm ALLEN BOLT....... 1 B23 SLIDE RAIL ANCHOR.......... 2 B24 M4 P0.75 10mm SCREW.. 4 C1 REAR STABILISER............ 1 C2 REAR END CAP.............. 2 C3 REAR END CAP SPACER....... 2 C4 M8x16mm ALLEN BOLT....... 2 D1 FRONT STABILISER........... 1 D2 FRONT END CAP............. 2 D4 M10 x 55mm ALLEN BOLT..... 2 D5 Ø10 x 2T x Ø23 FLAT WASHER.. 6 E1 FOOTPLATE................. 1 E2 PEDAL COVER............... 2 E3 PEDAL..................... 2 E4 PEDAL ADJUSTMENT PLATE.... 2 E5 FOOTPLATE STRAP........... 2 E6 PEDAL ADJUSTMENT KNOB..... 2 E7 STATIONARY CAM............ 2 E8 M4 FLAT WASHER............ 10 E9 M4 x 10mm SCREW.......... 2 E10 M4 x 16mm SCREW.......... 4 E11 M4 x 20mm SCREW.......... 2 E12 M4 x 20mm SCREW.......... 2 E13 M8 x 30mm ALLEN BOLT....... 4 F1 MONITOR STAND............. 1 F2R MONITOR TURNING HINGE R.... 1 F2L MONITOR TURNING HINGE L.... 1 F3 BUSHING................... 2 F4 M8 x 55mm ALLEN BOLT....... 1 F5 3/8 x 3-1/2 mm ALLEN BOLT... 1 F6 3/8 NYLON NUT.............. 1 G1 FAN WHEEL COVER R......... 1 G2 FAN WHEEL COVER L......... 1 G3 FLYWHEEL COVER R.......... 1 G4 FLYWHEEL COVER L.......... 1 G5 GRILL..................... 1 G6 AIR-INTAKE GRILL............ 1 G7 FLYWHEEL UPPER COVER...... 1 G8 M5 x 10mm SCREW.......... 3 G9 5/32 x 5/8(4x15) SCREW....... 6 G10 3/16 x 5/8mm SCREW......... 5 G11R MIDDLE COVER R............ 1 G11L MIDDLE COVER L............ 1 G12 3/16 x 1/2mm SCREW........ 6 G13 M5 x 10mm SCREW.......... 2 G14 M4 x 12mm SCREW.......... 1 H1 MONITOR.................. 1 H2 MONITOR PLATE............. 1 H3R MONITOR HOLDER R.......... 1 H3L MONITOR HOLDER L.......... 1 Page 23
MASTER PARTS & ACCESSORY LIST PART No. DESCRIPTION QTY I1 PACKING REINFORCEMENT...... 1 Page 24