Skull Party Favors Treat your Halloween party guests to a frightfully fantastic table! Easy to make decorations with Tulip 3D Fashion Paint, Fashion Glitter, Iron-On Crystals and Aleene s Acid-FreeTacky Glue. Instructions: Skull Bags Skull Bags 1. Enlarge skull pattern on a copy machine until it is approximately 3/8 smaller than the surface of the cookie bag (all sides). 2. Cut out pattern and place it under a cookie bag, lining it up with a 3/8 margin on the top and sides. 3. Trace over the image onto top of bag with Black Slick Tulip 3D Fashion Paint. Use one drop of White Slick to secure a clear crystal to one of the front teeth on each bag. Let dry.when dry, cut the sides of the bag slightly if necessary to easily slide treats inside. Secure bag with included twist tie and tie a bow with red ribbon.
Straw Covers 1. Change size of pattern pieces if desired and print. 2. Use a pencil to trace one of each piece onto cardstock and cut out. Use a cra knife to cut out the eyes, nose and corners of mouth on skull. 3. Trace and cut out one banner piece from black cardstock and one skull piece from white cardstock for each guest expected. 4. Outline skulls with Black Slick Tulip 3D Fashion Paint. Before paint dries, add one Red Tulip Iron-On Crystal to each eye. Write each guest s name on a banner piece with pencil then trace with True Red Slick. Let dry. 5. When dry, use Aleene s Acid-Free Tacky Glue to glue pieces together as shown. Use a hole punch to make two holes: one on top and one on bottom of skull. 6. Slide onto straw or stir stick then use finger to lightly press against paper to create a little wave formation as shown in the photo. Favor Boxes 1. Fill gi boxes with your preferred goodies. 2. Close the interlocking flaps on the box first, then bring the remaining flaps together and crease them upward where they meet in the center. Glue the flaps together with Aleene s Acid-Free Tacky Glue and secure with binder clip or chip clip until dry. 3. Enlarge patterns to desired size and print onto white cardstock. 4. Cut one each of flame background, flame and skull. Use cra knife to cut out the eyes, nose and corners of mouth on skull. 5. Use a pencil to trace one skull onto white fun foam and one flame background onto yellow fun foam for each box. Carefully cut each out. (Do not cut out facial features on skulls.) 6. Use Black Slick Tulip 3D Fashion Paint to color in facial details on the skulls. Tip: When drawing in the teeth, think upright candy corn shape for the top teeth and chicklette shapes for the bottom teeth. 7. Before the Black Slick dries, add one Red Tulip Iron-On Crystal to the center of each eye. 8. Using cardstock pattern and a pencil, lightly trace the flames onto the flame background pieces. Center the skull pattern and trace the outline inside the flames. 9. Use True Red Slick to color in the flames approximately 1/8 inside flame outline and 1/8 within the skull outline. Immediately sprinkle with Red Tulip Fashion Glitter. Let dry then shake o excess glitter onto a sheet of scratch paper and return to container for reuse. 10. Outline flames with Black Slick and let dry.when dry, squeeze needed amount of Aleene s Acid-Free Tacky Glue on back side of box top tab and on the back side of skull. Carefully center flame into glue on back side of box tab, and center skull onto front side of tab, sandwiching tab in between skull and flames. Let dry. Continue with each box until finished. Candle 1. Enlarge pattern as desired with a copy machine. 2. Pour Aleene s Acid-Free Tacky Glue into empty container. Add water and mix until it reaches a milky consistency. 3. Tear tissue paper into 3-5 squares; do not cut with scissors. 4. Clean glass container with glass cleaner. 5. Crumple several torn pieces of tissue then smooth back out to create a wrinkled look. Use a 1-1½ wide brush to dab a bit of the glue mixture onto a small area of outside of glass (about 2 ). Carefully attach a piece of tissue onto glass, keeping it wrinkled as much as possible, but not folded over onto itself. Once attached onto glass, carefully use paintbrush to dab glue mixture over all of tissue, working out bubbles as needed. Repeat process, overlapping tissue slightly until all of glass is covered. Tear small pieces of tissue and carefully patch holes as needed. Let dry. 6. When dry, use a razor blade or cra knife to trim excess tissue from the top and bottom edges of glass container. 7. Use fine-tip felt pen to trace enlarged skull pattern onto contact paper and cut out desired number with cra knife. Make sure to cut out eyes, nose and corners of mouth from each. 8. Remove backing from contact paper skull. Stick onto clean white T-shirt and remove to reduce the stickiness on back of stencil. Place where wanted on tissue-covered container. Repeat with remaining skulls. 9. Pour a puddle of Black Slick Tulip 3D Fashion Paint onto a piece of foil. Tap flat end of sponge into paint and dab onto entire tissue-papered surface of container. Use narrow ends and corners of sponge to dab Black Slick into stencil openings (eyes, nose and corners of mouth). Let dry, then carefully remove contact paper. 10. Carefully line up skull pattern inside glass container behind skulls on tissue paper and tape in place. Trace details onto tissue paper with pencil, then outline skulls with Black Slick. Let dry. 11. When dry, spray over all dimensional paint with Aleene s Spray Acrylic Sealer, Matte Finish. 12. When dry, use small liner paintbrush to apply Tulip Fashion Glitter Bond onto eyes, nose and corners of mouth of one skull at a
time. Sprinkle with Black glitter. When dry, shake o excess onto scratch paper and pour back into container for reuse. 13. Use small brush to add swirls around skulls as desired with Glitter Bond. Sprinkle with Red glitter. When dry, shake o excess. 14. Add a candle and enjoy! What you need: Tulip Fashion Glitter Black Fine Jewel (23560) Red Fine Jewel (23554) ilovetocreate products White 1.25 oz. (65000) Black 1.25 oz. (65038) True Red 1.25 oz. (65130) Miscellaneous: Craft knife or razor blade Glass cleaner Paintbrush 1-1½ and small liner Glass container Container (for mixing) Hole punch Pencil Cardboard lollypop cookie sticks White tissue paper Wedge makeup sponge Scratch paper Foil Cookie bags Contact paper T-shirt white Red ribbon Craft knife Scissors Rice Krispy Treats, cut to size and placed on cookie sticks Binder clip/chip clip Tape Felt pen fine-tip Stir sticks, straws or rubber bands
Paper towels Small Chinese food takeout style gift boxes, black Black and white cardstock Fun Foam: white, yellow Patterns:
Skull Party Favors pattern Designed By: iltc