88 5531 751 Closet Wall Drawer Unit A. B. C. Shelf D. E. F. For assembly see instructions in carton 88 5531 752.
88 5531 752 Closet Wall Drawer Unit G. H. I. Plinth M. Bottom L. N. 2 pc. J. K. O. Drawer Refer to the last page(s) of these Instructions for drawer assembly. Plug 4 pcs. (+1 extra) M3x15 8 pcs. (+1 extra) Adjustable Pin 12 pcs. (+1 extra) M4x15 Machine Screw 4 pcs. Hex Wrench M3x19 16 pcs. (+1 extra) M3x25 (long) 10 pcs. (+1 extra) Knob 2 pcs. Carton 88 5531 751 is also needed for assembly. Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8 Drill Bit
Assembly Instructions 6/8 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 9 Drill a 3/8 hole in wall in-line with the pre-drilled hole. Anchor in wall 3/8 wall hole on wall Wall Screw Pre-drilled hole Move unit. Insert Anchor into the wall hole and attach with Wall Screw. Tie end Attach at pre-drilled hole with. Lock end at top of unit Move unit back into place. If assembling multiple Closet Wall Units together, go to and complete Step 10 now, then return to and complete Step 9. Tipover Restraint Slide Tipover Restraint through on wall and on unit. (See Figure 5) Figure 5 Put tie end of Tipover Restraint into lock end of Tipover Restraint and pull until tight. Drill 3/8 hole in wall of unit Pre-drilled hole Anchor (+1 extra) 2 pcs. (+1 extra) Tipover Restraint (+1 extra) M3.5x40 Wall Screw (+1 extra) M3.5x16 (+1 extra)
Assembly Instructions 8/8 Drawer (O) O4 STEP 1 O2 O3 Attach O2 to O3 and O4, then flip the locks. (See Figure A) O5 O2 Figure 2 STEP 2 O1 Slide O5 into the grooves in O3 and O4. Be sure to push O5 all the way forward so it meets O2. STEP 3 Attach O1 to unit, then flip the locks. STEP 4 Attach Knob with machine screw. O1. Drawer Front O2. Drawer Back O3. Drawer Side O4. Drawer Side O5. Drawer Bottom
88 5531 761 Closet Wall Shelf Unit A. B. C. Shelf D. E. F. For assembly see instructions in carton 88 5531 762.
88 5531 762 Closet Wall Shelf Unit H. I. Plinth G. M. Bottom J. K. L. C. Shelf Plug 4 pcs. (+1 extra) M3x15 8 pcs. (+1 extra) Adjustable Pin 24 pcs. (+1 extra) 4 pcs. Hex Wrench M3x19 16 pcs. (+1 extra) M3x25 (long) 6 pcs. (+1 extra) 2 pcs. Carton 88 5531 761 is also needed for assembly. Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8 Drill Bit
Assembly Instructions 6/7 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 9 Drill a 3/8 hole in wall in-line with the pre-drilled hole. Anchor in wall 3/8 wall hole on wall Wall Screw Pre-drilled hole Move unit. Insert Anchor into the wall hole and attach with Wall Screw. Tie end Attach at pre-drilled hole with. Lock end at top of unit Move unit back into place. If assembling multiple Closet Wall Units together, go to and complete Step 10 now, then return to and complete Step 9. Tipover Restraint Slide Tipover Restraint through on wall and on unit. (See Figure 5) Figure 5 Put tie end of Tipover Restraint into lock end of Tipover Restraint and pull until tight. Drill 3/8 hole in wall of unit Pre-drilled hole Anchor (+1 extra) 2 pcs. (+1 extra) Tipover Restraint (+1 extra) M3.5x40 Wall Screw (+1 extra) M3.5x16 (+1 extra)
88 5531 771 Closet Wall Hanging Unit A. B. C. D. E. F. For assembly see instructions in carton 88 5531 772.
88 5531 772 Closet Wall Hanging Unit G. H. I. Rod 2 pcs. J. Plinth K. L. M. N. O. Bottom Plug 4 pcs. (+1 extra) M3x15 8 pcs. (+1 extra) M3.5x16 Rod Support 8 pcs. (+1 extra) 4 pcs. Hex Wrench M3x19 16 pcs. (+1 extra) M3x25 (long) 7 pcs. (+1 extra) Rod Support 4 pcs. 2 pcs. Carton 88 5531 771 is also needed for assembly. Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8 Drill Bit
Assembly Instructions 7/8 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 10 Drill a 3/8 hole in wall in-line with the pre-drilled hole. Anchor in wall 3/8 wall hole on wall Wall Screw Pre-drilled hole Move unit. Insert Anchor into the wall hole and attach with Wall Screw. Tie end Attach at pre-drilled hole with. Lock end at top of unit Move unit back into place. If assembling multiple Closet Wall Units together, go to and complete Step 11 now, then return to and complete Step 10. Tipover Restraint Slide Tipover Restraint through on wall and on unit. (See Figure 7) Figure 7 Put tie end of Tipover Restraint into lock end of Tipover Restraint and pull until tight. Drill 3/8 hole in wall of unit Pre-drilled hole Anchor (+1 extra) 2 pcs. (+1 extra) Tipover Restraint (+1 extra) M3.5x40 Wall Screw (+1 extra) M3.5x16 (+1 extra)