HF ANTENNAS INDEX Page No. HF BASE ANTENNAS HF Broadband Multi-wire Base Antenna 120 Watt 1 HF Extended length Broadband Multi-wire base antenna 120 Watt 1 HF Broadband Multi-wire Heavy Duty Base Antenna 120 Watt 2 HF Broadband Multi-wire Base Antenna 500 Watt 3 HF Extended Broadband Multi-wire Base Antenna 500 Watt 3 HF Broadband Multi-wire Base Antenna 1000 Watt 3 HF Extended Broadband Multi-wire Base Antenna 1000 Watt 4 HF Semi-Delta Antenna 500 Watt 5 HF Biconical Dipole 2-30 MHz 6 HF Biconical Dipole 2-30 and 3-30MHz 9 HF Travelling Wave Dipole 11 HF Delta Antenna 1000 Watt 12 HF Folded Dipole 14 HF Horizontal Wire Log Periodic 17 HF Wire Rhombic Antenna 21 HF Centre Fed Single wire Antenna 150watt CFB-150 24 HF Vertical Wire Log Periodic Antenna 25 HF Wire Vertical Omnidirectional Antenna 27 HF Broadband Tactical End Fed Antenna 1 Kilowatt 29 HF PORTABLE ANTENNAS HF Collapsible Backpack Whip (with Goose neck) 30 HF Tactical Broadband Antenna 31 HF Manpack Tape Whip 32 HF VEHICLE ANTENNAS HF Heavy duty Fibreglass vehicle Whip 33 HF Heavy Duty vehicle Whip NATO Base 34 HF Heavy Duty Glass Fibre 2 Section vehicle Whip 5m 35 HF Auto-Tune Antenna 1.6-30 MHz 36 HF MARINE/SHIPBORNE ANTENNAS HF MARINE Shipboard 7m Whip Antenna and Tuner 38 VHF ANTENNAS VHF UHF Folding Log Periodic Base antenna 41 VHF UHF Discone Base Antenna 108-400MHz 42 VHF UHF Folding Log Periodic 25-200MHz Base Antenna 46 VHF Elevated Wideband Base Antenna 30-108 MHz 47 VHF UHF Folding Log periodic Portable Antenna 48 VHF UHF Handheld Rubber Ducky 49 VHF Manpack Whip 136-174 MHz 50 VHF UHF Personal Radio Whip 350-450MHz 51 VHF Manpack Tape Whip 52 VHF UHF 2 Section Broadband Vehicle Whip 53 VHF Vehicle Whip 30-108 MHz 56 VHF UHF Vehicle Whip 25-500 MHz 57 UHF ANTENNAS VHF UHF Base Discone Antenna 58 UHF Elevated Fixed Station Antenna 450-500 MHz 59 UHF Wide-band Manpack Antenna 60 VHF UHF Marine Shipboard Discone Antenna 62 MICROWAVE ANTENNAS Corner Reflector 6 element Base Antenna 63 Dual Band UHF & Microwave Vehicle Whip 68 High Gain WiFi Collinear 2400-2500MHz Omni-directional Vehicle Antenna 69 L Band 960-1240MHz Vehicle Whip 70 L Band 500-2000MHZ Marine Antenna 71 L Band 960-2000MHZ Marine Antenna 74 MAST AND TOWERS Pneumatic Telescopic Mast Range 75 Light Duty Portable (Tactical) Masts 76 Guyed Aluminium Tube Mast 77 Tower 15 Metre Guyed Butt Mast 78 Tower 3m Section 15.9 Metre Guyed Butt Mast 79 ACCESSORIES BPGLASS Non conductive guy cable (Debeglass) 80 Surge Arrestor 82 Lightning Arrestor Kit 83
This catalogue is a representative sample of the range of products we can manufacture and supply. For a more comprehensive insight into our capabilities please visit our website: www.broadbandpropagation.com We are also specialists in custom design and manufacture so if you have a particular antenna need which you are having difficulty in sourcing please contact us with your requirements. Our Contact Details: Broadband Propagation Pty Ltd. STREET ADDRESS 1-3 ADELAIDE ROAD ECHUNGA SOUTH AUSTRALIA 5153 POSTAL ADDRESS P.O.BOX 529 ECHUNGA SOUTH AUSTRALIA 5153 PHONE +61 8 8388 8132 FAX +61 8 8388 8536 EMAIL WEBSITE sales@broadbandpropagation.com www.broadbandpropagation.com ABN 47 143 178 438
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 47 143 178 438 BPA 120 High efficiency broadband multi-wire base antenna. Sturdy stainless steel and fibreglass construction can be mounted horizontally or as inverted vee. Supplied with 30m of co-axial cable and instructions. SPECS: Frequency Range: 2-30 MHz Power Rating: 150 Watts PEP Input Impedance 50 Ohms Connector: UHF Female Coax Cable: 30m RG58 with connectors. (other cable types and lengths available on request) Overall Length: 28m NO ANTENNA TUNER REQUIRED. BPA 120E Extended Length Version of BPA-120 for increased performance at 2-3 MHz. SPECS: Frequency Range: 2-30 MHz Power Rating: 150 Watts PEP Input Impedance 50 Ohms Connector: UHF Female Coax Cable: 30m RG58 with connectors. (other cable types and lengths available on request) Overall Length: 52m NO ANTENNA TUNER REQUIRED. 1
Pty. Ltd. CAN: 143178438 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47143178438 BPA-120-HD HF BROADBAND WIRE BASE ANTENNA The BPA-120-HD is a 150 Watt rated, centre-fed, broadband antenna with an overall length of 28 meters. Radiation efficiency exceeds that of other antennas in this class. The frequency range is continuous across the full HF band from 2-30MHz. No antenna tuner is required. Construction is of 3.2 mm stainless steel cable with UV-stable fibreglass spreaders and and diecast aluminium component cases. All external fittings and connections are of stainless steel. Lightning protection is provided. The antenna can be mounted horizontally or as an inverted V. The HD version of the BPA-120 is constructed from heavy gauge stainless steel wire and uses heavy duty spreaders and other components to enable it to withstand cyclonic conditions.. Specifications Frequency range: Feed Impedance: Power Input: Input Connector: Mast height: Mast spacing: Wind rating: Temperature: Shipping weight: Shipping size: 2-30 MHz 50 Ohms 250W PEP, 150W data N type Female 10 metres minimum 30 metres minimum 250 kilometres/ hour -20 to 65 deg. C. ambient 12 kilograms 130 x 30 x 15 cm. 2
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 47 143 178 438 BPA-500 Broadband Multi-wire base antenna for 500 Watts PEP. Sturdy Stainless steel and fibreglass construction can be mounted horizontally or as inverted vee. Supplied with 30m of coaxial cable and instructions. SPECS: Frequency Range: 2-30 MHz Power Rating: 500 Watts PEP Input Impedance 50 Ohms Connector: N type Overall Length: 28m NO ANTENNA TUNER REQUIRED. BPA-500E Extended Length Version of BPA-500 for increased performance at 2-3 MHz. SPECS: Frequency Range: 2-30 MHz Power Rating: 500 Watts PEP Input Impedance 50 Ohms Connector: N type Overall Length: 52m NO ANTENNA TUNER REQUIRED. BPA-1000 Broadband multi wire base antenna for 1 Kilowatt PEP. Sturdy Stainless steel and fibreglass construction can be mounted horizontally or as inverted vee. Supplied with 30m of coaxial cable and instructions. SPECS: Frequency Range: 2-30 MHz Power Rating: 1 KWatts PEP Input Impedance 50 Ohms Connector: N type Overall Length: 28m NO ANTENNA TUNER REQUIRED. 3
Pty. Ltd. CAN: 143178438 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47143178438 BPA-1000E Extended Length Version of BPA-1000 for increased performance at 2-3 MHz. SPECS: Frequency Range: Power Rating: Input Impedance: Connector: Overall Length: 2-30 MHz 1 Kilo Watts PEP 50 Ohms N type 52m NO ANTENNA TUNER REQUIRED. 4
Pty Ltd 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47 143 178438 BPA-SD-500 BROADBAND HF SEMI DELTA OMNI DIRECTIONAL BASE ANTENNA The BPA-SD-500 is a 500 Watt rated Semi-Delta antenna with a high vertical gain radiation pattern, suitable for NVIS (short range) communication. With a small mounting footprint of 20m, it is ideal for installation where space is limited. No antenna tuner is required. Construction is of 3.2mm stainless steel cable with an aluminium spreader and die cast aluminium component cases. All external fittings and connections are of stainless steel. Specifications Frequency range: 2-30 MHz Feed Impedance: 50 Ohms VSWR*: Better than 2.0:1 Typical, Max. 2.5:1 Power Input: 500 Watts Radiation Patterns: Horizontal: Essentially omnidirectional Vertical: High vertical gain Input Connector: UHF type socket Mast height: 10 metres min. Wind rating**: 210 k/h Temperature: -30 to 55 deg. C. Shipping weight: 17 kilograms Shipping size: 200 x 30 x 19 cm Options. 1. Supplied with 30 meters of RG 58 or RG 213 coaxial cable fitted with UHF/ N type connectors. 2. Central Pulley/halyard kit Please specify option required (by description) when ordering > *Measured at transceiver with 30m of RG 58 feeder **In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989 5
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 HF BROADBAND BICONICAL DIPOLE Model: BPBD-2-30 Our HF broadband Biconical Dipoles are highly efficient, horizontally polarised antennas that at lower frequencies have high-angle radiation components suitable for short (NVIS) to medium range communication and at higher frequencies have the strongest signals at lower angles, for long range propagation. The antenna is centre fed and can be supplied with power ratings ranging from 200 watts, to 10 Kilowatts CW (Continuous). The antennas are almost 100% efficient across the full operating range of frequencies. No power is lost in tuning or loading devices. The antenna is ideal for frequency agile transmissions and is constructed of high grade materials throughout. The design is a cost effective solution for broadband HF short and medium range communications and is easy and safe to install, requiring only two vertical towers to mount the antenna. The antenna can be easily lowered for maintenance or repair. Feed to the antenna is via coaxial cable to a balun mounted at the antenna, for power ratings up to 1 Kilowatt or via a pole mounted balun and open wire, balanced ladder line, for higher power ratings. Specifications ~ Broadband, 2-30 MHz ~ Omni directional ~ No Antenna Tuner ~ No Resistive Loading ~ Easy to Install Electrical Frequency: Gain: VSWR: Polarisation: Power Rating: Input Impedance: Input connection: 2-30 MHz 8.5 dbi 2.0-1 most of band, 2.5:1 maximum Horizontal Rx, 1 KW, 5KW, and 10 KW Average 50 ohms N, DIN 7/16, 7/8 EIA, or 1-5/8 EIA, Dependant on power rating B/Prop HF Biconical Dipole_2-30_specs.doc Page 1 of 3 6
Specifications Mechanical Mast Height: 20m Overall length: 80m* Overall Width: 40m Wind Rating 230 km/hr * Antenna length measured at extreme guying points All metal materials are of high grade stainless steel or hotdip galvanised steel. Ceramic insulators used throughout. 3D Pattern @ 2MHz RADIATION PATTERNS: B/Prop HF Biconical Dipole_2-30_specs.doc Page 2 of 3 7
RADIATION PATTERNS: VSWR PLOT B/Prop HF Biconical Dipole_2-30_specs.doc Page 3 of 3 8
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 HF BROADBAND BICONICAL DIPOLE Models: BPBD-2-30 and: BPBD-3-30 Our HF broadband Biconical Dipoles are highly efficient, horizontally polarised antennas that at lower frequencies are suitable for short to medium range communication and at the higher frequencies have the strongest signals at lower angles for long range propagation. The antenna is centre fed and can be supplied with power ratings ranging from 200 watts, to 10 Kilowatts CW (Continuous). The antennas are almost 100% efficient across the full operating range of frequencies. The antenna is ideal for frequency agile transmissions and is constructed of high grade materials throughout. Full lightning protection is provided 9
Specifications BPBD-2-30 BPBD-3-30 Electrical Frequency: 2-30 MHz 3-30 MHz Gain: 8.5 dbi VSWR: 2.0-1 most of band, 2.5:1 maximum Polarisation: Horizontal Power Rating : 250 watt average (1 kw PEP) 1Kilowatt average (4 kw PEP) and 10 Kilowatt (40 kw PEP) models available Input Impedance: Input connection: 50 ohms Dependant on power rating Mechanical Mast Height: 20m 15m Overall length: 101m 72m Overall Width: 40m 30m Wind Rating 230 km/hr All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. 10
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPA-TWD HF BROADBAND DIPOLE This broadband dipole is a resistively terminated broadband antenna which when mounted as an inverted V has minimum lobe break up at the higher end of the HF spectrum. It has been specially developed as an HF reference antenna rather than a communications antenna. Constructed to the highest quality standards with powder-coated aluminium, balun and load cases, UV stabilized fiberglass spreaders, cable strain relief and connector weather shrouding. Specifications Frequency range: 1-30 MHz Input Impedance: 50 Ohms nominal Power Input: 200 Watts CW Input Connector: N Female VSWR: Better or equal to 2.5:1 full band Better or equal to 2:1 most of the band* Max.Wind Speed: 250 kilometres/ hour* Dimensions for Inverted Vee mounting Central Mast height: 15 metres Outer Mast Height 2-2.5 metres Outer Mast spacing: 50 metres Shipping weight: 10 Kilograms Shipping size: > 132.5 x 31.5 x 24 cm *Measured at antenna feedpoint *In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989 11
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPA-DELTA 3-30-1000 ANTENNA The BPA-DELTA 3-30 1000, antenna is a broadband, omni-directional, vertically polarized antenna with a high angle of radiation suitable for short to medium range communication. (up to 1000 kms) A central Balun which is fed by 50 Ohm coax feeds both arms of the antenna. Antenna arms are supported by a 17m central mast (not supplied) and two stub masts (see drawing overleaf) Construction is of 3.2 mm stainless steel cable with UV stable fibre-glass spreaders and powder coated aluminium and glass reinforced polyester component cases. All external fittings and connections are of stainless steel. Lightning protection is provided. Specifications Frequency range: 3-30 MHz Feed Impedance: 50 Ohms Balun connection: N type socket Power Input: 1000 Watts PEP. VSWR: Better than 2:1* Mast height: 17 meters 52 meters Wind rating: 210 kilometers/ hour* Temperature: -30 to 55 deg. C ambient Shipping weight: 20 kilograms Shipping size: 200 x 31.5 x 24 cm Options. 1. Supplied with 30 meters of RG 58 or RG 213 coaxial cable fitted with UHF or N connectors at both ends. 2. Central Pulley/halyard kit Please specify (by description) when ordering > *In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989 *Measured at transceiver with 30m of RG 58 feeder *Antenna height 10m, Gnd: Diel const. 10, Cond. 0.002 12
BPA-DELTA 3-30-1000 ANTENNA 13
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 FD-150-22m HF BROADBAND Folded Dipole The folded dipole is a resistively terminated broadband antenna which although inefficient compared with other broadband HF designs* is low cost, compact, light and easily installed. The antenna is an old design first described in amateur circles in 1951. Barker and Williamson pioneered commercialization of the design and it is still a popular antenna, in widespread use. The antenna can be installed as a flat top, sloper or inverted "V". Our folded dipoles are, as with our other antennas, constructed to the highest quality standards with aluminium balun and load cases, UV stabilized fiberglass spreaders, cable strain relief and connector weather shrouding. No antenna tuner is required Specifications Frequency range: 5-18 MHz Input Impedance: 50 Ohms nominal Power Input: 150 watts PEP Input Connector: UHF Socket VSWR: Better than or equal to 2:1 Max.Wind Speed: 250 kilometres/ hour* Dimensions for Inverted Vee mounting Central Mast height: 6.5 metres.(minimum) Outer Mast Height 2.4 metres (Minimum) Outer Mast spacing: 24 metres Shipping weight: 6 Kilograms Shipping size: 800 x 650 x 200 mm Options #1 Supplied with nominated length RG58 or RG213 (low loss) coaxial cable fitted with connectors at both ends. #2 Supplied with Central Mast halyard and pulley Please specify (by description) when ordering > *In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989 *Measured at transceiver with 30m of RG 58 feeder 14
Folded Dipole Model No. FD-150-22m Specification Sheet Construction Ruggedly constructed to exacting standards using heavy-duty 3.2mm stainless radiating wires with solid UV resistant wire spreaders, and powder coated Aluminium component cases. An integral connector weather shroud is provided to protect the coax-antenna connection. Antenna is supplied fully assembled and includes necessary hardware for mounting as an inverted vee. Specifications Frequency range: Recommended 6-18 MHz, Useable 5-18 MHz Input Impedance: 50 Ohms nominal Power Input: 150 watts PEP, 100 watts CW Input Connector: UHF Socket VSWR: Better than or equal to 2:1 Max.Wind Speed Rating: 250 kilometres/ hour Dimensions for Inverted Vee mounting Central Mast height: 6.5 metres.(minimum) Outer (Stub) Mast Height 2.4 metres (Minimum) Outer (Stub) Mast spacing: 24 metres (Using above minimum heights) Minimum Overall Mounting Space Required 24 metres (Using above heights & spacings) Shipping weight: Shipping size: 10 Kilograms 800 x 650 x 200 mm Options #1 Supplied with nominated length of RG58 or RG213 (low loss) coaxial cable fitted with connectors at both ends. (Please specify connector type) #2 Supplied with Central Mast halyard and pulley 15
Terminated Folded Dipole FD-150-22m, Radiation Patterns Antenna length 22m antenna height 6m 16
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 HF BROADBAND HORIZONTALLY POLARISED LOG PERIODIC ANTENNA Models: BPLP-2-30, BPLP-3-30 and BPLP-5-30 Our HF Broadband Log Periodics are almost 100% efficient and are short to medium range antennas. They can be supplied in a number of models to suit differing frequency spans. They are high gain and directional and can be configured as bidirectional if two are mounted back to back. The antennas are end fed and can be supplied with power ratings ranging from 200 watts, to 10 Kilowatts CW (Continuous). The antennas are almost 100% efficient across the full operating range of frequencies. Radiation is horizontally polarised Full lightning protection is provided 17
Specifications BPLP-2-30 BPLP-3-30 BPLP-5-30 Electrical Frequency: 2-30 MHz 3-30 MHz 5-30 MHz Gain: Dependant on frequency 8-13 dbi VSWR: 2.0-1 most of band, 2.5:1 maximum Polarisation: Horizontal Power Rating : 250 watt average (1 kw PEP) 1Kilowatt average (4 kw PEP) and 10 Kilowatt (40 kw PEP) models available Input Impedance: Input connection: 50 ohms Dependant on power rating Mechanical Mast Height: 23m 18m 12m Overall length: 130m 100m 65m Overall Width: 80m 62m 40m Wind Rating 150 km/hr All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. RADIATION PATTERNS 18
Specifications BPLP-2-30 BPLP-3-30 BPLP-5-30 Electrical Frequency: 2-30 MHz 3-30 MHz 5-30 MHz Gain: Dependant on frequency 8-13 dbi VSWR: 2.0-1 most of band, 2.5:1 maximum Polarisation: Horizontal Power Rating : 250 watt average (1 kw PEP) 1Kilowatt average (4 kw PEP) and 10 Kilowatt (40 kw PEP) models available Input Impedance: Input connection: 50 ohms Dependant on power rating Mechanical Mast Height Minimum 23m 18m 12m Overall length: 130m 100m 65m Overall Width: 80m 62m 40m Wind Rating 150 km/hr NOTES ON MAST SIZES REQUIRED The centre mast heights given are preferred heights for the antenna attachment points. Towers can be higher to suit standard sizes of locally available masts. Required centre mast types: Medium-duty, Triangular Section Guyed Butt Mast for the BPLP-2-30 and BPLP-3-30 Light Duty, Triangular section Guyed Butt Mast for the BPLP-5-30 Typical 15m Light-Duty, Triangular Lattice, Guyed Butt Mast Specifications Design Wind Speed: 50.0 m/s Lateral Ancillary Load: 7kN applied as point load at top of mast Mast Width: 305mm Number of guys: 3 sets of top and middle guys at 120 deg. Guying Radius: 8m Typical 20m Medium-Duty, Triangular Lattice, Guyed Butt Mast Specifications Design Wind Speed: 54.0 m/s Lateral Ancillary Load: 10kN applied as point load 2m below top guying point Mast Width: 305mm Number of guys: 3 sets of top and middle guys at 120 deg. Guying Radius: 15m 19
STUB MAST The stub mast for all models is 50mm diameter, 3mm wall thickness, galvanised steel tubing. Overall length 3m (0.5m in ground footing, 2.5m above ground) Guying is required using 4-5mm stainless or galvanised wire rope into concrete guy anchors at a guying radius of 2.5m. Welded lugs are required on the stub mast. details will be provided on receipt of purchase order. 20
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 HF RHOMBIC ANTENNAS Models: BPRH-3-12; BPRH-4-16; BPRH-5-20 Rhombic antennas have high directional gain and low take-off angles, best suited to long distance, point to point communications. Three models are available covering 3-12, 4-16, and 5-20 MHz. Installation area needed is relatively large, especially for the low frequency model, and four masts are used, however installation of the antenna is simple and can be carried out without specialist skills. Our HF Rhombic range offer a cost effective answer for permanent base stations where low take-off angle, and high directional gain is needed, with good radiation efficiency. High Gain (to 18 dbi) Low Radiation Angles High Radiation Efficiency Page 1 of 3 jb RHOMBIC SPECs.doc Rev #3 2008 21
Specifications Electrical BPRH-3-12 BPRH-4-16 BPRH-5-20 Frequency: 3-12 MHz 4-16 MHz 5-20 MHz VSWR: Gain: Take-off Angle: Polarisation: Power Rating : Input Impedance: Input connection: Mechanical Better than 2.0 : 1 across band ~12 dbi Low end of Band ~16dBi Mid-band ~18dBi High end of Band 26 Deg Low end of Band 14 Deg Mid-band 10 Deg High end of Band Horizontal Antenna only (all Models) Max. 30 kw Average, 60 kw PEP, Overall rating dependant on ratings of Balun/ Termination pair Which are available from 1-20 kw 50 ohms Dependant on balun power rating BPRH-3-12 BPRH-4-16 BPRH-5-20 Mast Height: 40m 30m 24m Overall length: 410m 310m 248m Overall Width: 220m 165m 134m Wind Rating: 150 km/hr Construction All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. General The antenna is supplied with all fittings required for installation, masts are not included. Masts may be quoted separately if you would like us to supply these also. The antenna may be fed via coaxial cable to the tower mounted balun or can be fed via suitable balanced open wire line from the transmitter hut. Balun and termination requirements are dependant on the power rating required for the installation and are available from 1-20 kw. Page 2 of 3 jb RHOMBIC SPECs.doc Rev #3 2008 22
VERTICAL RADIATION PATTERNS These plots apply to the lowest, middle and highest frequencies for each antenna model. Page 3 of 3 jb RHOMBIC SPECs.doc Rev #3 2008 23
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 CFB-150 CENTRE-FED, BROADBAND HF WIRE ANTENNA, PORTABLE The CFB-150 is a centre-fed, broadband, single wire dipole. Construction is of marine grade stainless steel wire. This antenna offers good performance in a simple easy to deploy portable package. It can also be used in semi permanent applications. Operation covers the full range of 2-30 MHz with instantaneous response to any frequency within this range, suitable for high speed, frequency-hopping radios. The antenna can be operated horizontally or as an inverted V. NO ANTENNA TUNER OR ANTENNA ADJUSTMENT IS REQUIRED It is recommended that for portable use the antenna be used with our BPV-TM range of lightweight portable tactical masts. This antenna/ mast combination offers the best available performance and ease and speed of deployment. Specifications Frequency Range: Input impedance: Polarisation: VSWR: Power Rating: Input Connection: Antenna Length: Antenna Height: Antenna Weight: Wind Rating: Operating Temperature: Operating Humidity: 2-30 MHz 50 Ohms Linear, Horizontal Better than 2:1 from 2-30 MHz 150 watts PEP N type female Mil. Spec 32 metres Minimum 5 metres 1.3 kg 220 Kilometres/ hr* -30 to 55 Degrees C ambient 0-100% relative humidity *AS1170.2 SAA Loading code; Wind Loads Options Coaxial Cable: 30 metres of Mil. Spec. RG-58 cable fitted with suitable connectors 24
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 HF BROADBAND VERTICALLY POLARISED LOG PERIODIC ANTENNA Models: BLPV-2.5-30, BLPV-4-30 and BLPV-6-30 Our HF Vertically Polarised, Broadband Log Periodics radiate a low angle directional pattern with gains from 8-12 dbi (depending on frequency) Best suited for long distance communication they can be supplied in a number of models to suit differing frequency ranges. They can be configured as bi-directional if two are mounted back to back or in a "rosette" configuration of four antennas for omnidirectional coverage (or switched directional coverage.) The antennas are end fed and can be supplied with power ratings ranging from 250 watts, to 10 Kilowatts CW (Continuous). The antennas are almost 100% efficient across the full operating range of frequencies. Radiation is horizontally polarised Full lightning/ static discharge protection is provided 25
Specifications BLPV-2.5-30 BLPV-4-30 BLPV-6-30 Electrical Frequency: 2.5-30 MHz 4-30 MHz 6-30 MHz Gain: 9 dbi VSWR: Less than or equal to 2.0-1 Polarisation: Vertical Power Rating : 250 watt average (1 kw PEP) 1Kilowatt average (4 kw PEP) and 10 Kilowatt (40 kw PEP) models available Input Impedance: Input connection: 50 ohms Via Balun or balanced 300 ohm open wire feeder Dependant on power rating Mechanical Mast Height: 75m 50m 35m Stub Mast Height 5.5m 5.5m 5.5m Overall length: 147m 90m 65m Overall Width: 76m 50m 35m Wind Rating 210 km/hr (antenna rating) All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. 26
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 HF BROADBAND VERTICALLY POLARISED LOG PERIODIC ANTENNA Models: BPVLP-2-28, BPVLP-2.7-28 and BPVLP-4-28 Our HF Broadband Vertical Log Periodics are almost 100% efficient and are short to medium range antennas. The design concentrates radiation vertically at the higher (overhead) radiation angles making it suitable for short range NVIS HF communications (0-300kms) and for medium range transmissions. The high angles of radiation make the antennas very suitable for ground to air communications. In the horizontal plane the antenna is essentially omni-directional No resistive terminations are used so the radiation efficiency is very high A single tower supports the antenna and no additional stub masts are needed. Compared with other large HF Broadband antennas the area of land required for installation is small. The antenna is suitable to mount on a wide range of commercially available guyed triangular lattice towers. Power ratings are available from 100 watts CW to 10 kilowatts CW 27
Specifications BPVLP-2-28 BPVLP-2.7-28 BPVLP-4-28 Electrical Frequency: 2-28 MHz 2.7-28 MHz 4-28 MHz Gain: Dependant on frequency, Nominal 3.5-6.5 dbi VSWR Nominal: 2.2:1 2:1 2:1 Azimuth Pattern: essentially omnidirectional (circular) Polarisation: - - - Vertical - - - - Power Rating : 250 watt CW (1 kw PEP) 1 Kilowatt CW (4 kw PEP) and 10 Kilowatt CW (40 kw PEP) models available; Please Specify when ordering (other power ratings available on request) Input Impedance: - - - 50 ohms - - - - Input connection: Dependant on power rating, 250 watt CW N type female 1 Kilowatt CW N type female 10 Kilowatt CW 1-5/8" EIA Flange Mechanical Mast Height: 38m 30m 18m Installation Area (to Guys): 95m x 95m 54m x 54m 45m x 45m Wind Rating - - - 180 km/hr (50m/s) - - All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. RADIATION PATTERNS 28
Pty Ltd 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47143178438 EFB-1000-TM : TACTICAL HF BROADBAND END FED ANTENNA 1 KILOWATT The EFB-1000-TM is an end-fed single wire HF broadband antenna designed for portable/ tactical use. It is operated as an inverted "V" Antenna and has a power rating of 1kw CW (4kw PEP) The antenna has its feed-point conveniently located at ground level at one end of the antenna. It is suitable for ground, vehicle and shelter installation and comes complete with a rapidly deployable earth radial system, 10m FRP hand operated telescopic mast and accessories. The radiation pattern is directional with a component of high angle radiation at the lower frequencies for closer communication distances. (NVIS) Construction is rugged and the antenna is designed to be portable and rapidly assembled and disassembled The antenna and mast kit includes convenient carrying bags. Erection of the antenna only requires a ground-space footprint of 20metres x 12metres No antenna tuner is required Specifications Frequency range: 3-30 MHz Input Impedance: 50 Ohms nominal Power Input: 1 Kw Ave, 4 Kw PEP VSWR: Better than or equal to 2:1 across the band Polarisation: Vertical Gain Min: -2dBi at 3 MHz Gain Max: 4.5dBi at 30 MHz Input Connector: N type Female Radiation Pattern: Broadly directional with significant high angle component at lower frequencies Antenna Length: 20m Including earth radials Antenna Width: 12m Including earth radials Options #1 Supplied with nominated length of RG213 (low loss) coaxial cable fitted with N connectors at both ends. Supplied with kit is Model BPV-TM-35-8 Tactical Mast No. of Sections 8 Extended Height 10m (35ft) Retracted Height 1.8m Guying Radius 6m Mast Weight 3.35kg Accessories Weight 5kg Construction Glass/ carbon composite The antenna kit is supplied with BPV-TM-35-8 Tactical Mast, guys stakes and ground plate. Radiating elements & earth radial system kit. One Kilowatt RF transformer. Balun mounting stakes, and all other required accessories for a complete installation package. 29
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPA-2-SW, BPA-6-SW, BPA-8-SW, BPA-10-SW COLLAPSIBLE BACKPACK WHIP ANTENNAS Lightweight, (a fraction of the weight of standard copper-coated steel Military backpack whips) our range is constructed from a highly specialized, heat treated and mechanically processed aluminium alloy with tensile and strength properties exceeding tubing of almost any other material including treated steel and glass laminates. Precision joint and tension cord system allowing rapid assembly and disassembly (in seconds) Available as standard in 2, 4, 6, 8 and 10 sections. Number of sections and section lengths can be tailored for custom orders. Standard tube diameter is 10mm but can also be supplied in other diameters. All whips are available with replaceable tension-cord option for field serviceability. Supplied with a range of standard radio connections including C, BNC and N type, threaded connectors to any format, or custom connectors to specification. BPA-1-GN FLEXIBLE GOOSENECK A rugged flexible gooseneck for use with backpack whip antennas which allows firm positioning of the whip. The Gooseneck length is 145 mm and can be supplied with a range of standard radio connections including C, BNC and N type, threaded connectors to any format, or custom connectors to specification 30
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 SWQ-150-M HF Tactical Broadband Antenna The SWQ-150-M Tactical, Broad-band Antenna is a portable, HF broad-band antenna designed specifically for mobile and portable HF communication where rapid deployment and simplicity of operation is essential. It can also be installed as a semi-permanent base station antenna. The antenna will operate at all frequencies in the 2-30 MHz band without any adjustment or tuning required. It is ideal for use in conjunction with modern, digitally configured, HF communication transceivers where features such as ALE and frequency hopping require true broadband capability. No masts or guying are required. The antenna will work successfully supported by trees, the tops of vehicles or trucks or any convenient object or structure. The antenna works most effectively when supported at a reasonable height, but it will also radiate (with lower efficiency) when stretched out on the ground. (If no support is available) The radiation pattern of the antenna has a significant vertical component at all frequencies, making it ideal for NVIS applications. Deployment time is, typically, 15-20 seconds from unpack to ready to go The antenna is supplied with Mil. Spec cable and connectors Component case is of rugged die-cast aluminium and the earth stake is of stainless steel with heavy-duty 0.315 (8mm) shaft. A 50 (15m) throw line and 16 (5m) ancillary line, of high quality braided nylon cord are included. Specification Operating Frequency: Input Power: Input Impedance: VSWR: Input Connector: Packed Weight: Packed Size: 2-30 MHz 150 watts SSB PEP 50 Ω Typically better than 2:1 across the band Supplied with 5 metres of coax fitted with N, UHF or BNC plug. (Specify option required when ordering) 2.9 lb (1.3 kg) 10 x 5 x 3 (254mm x 127mm x 76mm) 31
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BP-HF-2-STW BACKPACK TAPE WHIP ANTENNAS Broadband Propagation manufactures a range of light-weight, flexible, tape whip antennas for use with HF man-pack transceivers. Standard length is one metre. Designed for use in tactical combat, in all types of operating conditions from arctic through to extreme desert environments they are constructed of highly durable, long-life, spring steel elements which will not break or lose their set. A flexible nylon braid covers the whip, increasing durability and providing high voltage contact protection. Antenna mounting connectors including thread, BNC, N, or C type can be provided or customer specified mountings can be supplied. The antenna is supplied with a goose neck base allowing for instant angle adjustment. Specifications Frequency Range: Impedance: Radiation Pattern: Polarisation: Power Rating: Input Connection: Antenna Length: Antenna Width: Antenna Weight: Temperature Rating: 2-30 MHz Nominal Omni-Directional Vertical 10 watts CW Customer specified 1.0 metres 13 mm 130 grams -40 to +70 deg C Fully Flexible. Integral Goose Neck. Fully corrosion resistant. Sand abrasion resistant. Fungal attack protected. UV stable. Customer Specified Mounting 32
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPV-160-24 Heavy Duty Glass Fibre Whip The BPV-160-24 is a ruggedly constructed tuned whip built from a solid glass fibre core covered with a heavy-duty braided copper conductor and an insulating sheath. Solid construction offers greatly increased impact survival over hollow glass fibre whips. (Survives better than 35 impacts at midpoint at speed of 40 Km/h) The insulating sheath enables it to be used in environments where there is risk of contact with high voltage sources such as fallen power lines. The fully enclosing copper, braided conductor enables a very efficient transfer of radiated power and high power rating. It can be supplied as a single piece, or made up of 2 or more heavy duty threaded joints. The standard length is 2.4m but it can be supplied at other lengths according to customer requirements. Note: The antenna needs to be used with a suitable Antenna Tuner Unit. Specifications Frequency range: 1.5 to 30 MHz tuneable Input Impedance: 50 Ohms (with suitable tuner) Power Rating: 1000 watts CW Polarisation: Vertical Radiation pattern: Omni-Directional Colour: Matt Black overall Diameter: 15mm Length: 2.4m Weight: 1.3 kg Impact: better than 35 impacts midpoint at speed of 40 km/h) Mounting: Standard mount is via ½ Whitworth stud. (Can be supplied with other base attachment formats or threads) Note: drawing shows base which is not included. 33
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPV- BASE160-24 Heavy Duty Military Vehicle Antenna Base Designed and constructed for maximum strength and durability from aluminium alloy, stainless steel and high tensile fasteners. The body is machined from a solid billet of Acetal Copolymer (Delrin) and the base is fitted with a very rugged heavy duty barrel spring The mounting flange accommodates both UK/ NATO 6 or 3 hole pattern and USA 4 hole pattern enabling a standard fit on most military vehicles. SPECIFICATIONS Mounting: UK/ NATO 6 or 3 hole pattern and USA 4 hole pattern Power Rating: One Kilowatt Connection: Impact: Via heavy duty HV cable with stud clamp. In conjunction with a 2m non destructible test Whip, better than 200 impacts at 40 km/h Color: Matt Black overall Base Diameter: 140mm Overall height: 250mm Weight: 2.23 Kilograms Whip Attachment: ½ Whitworth female as standard (other thread or style can be specified) 34
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPV-160-50 Heavy Duty Glass Fibre Whip The BPV-160-50 is a ruggedly constructed tuned whip built from a solid glass fibre core covered with a heavy-duty braided copper conductor and an insulating sheath. Solid construction offers greatly increased impact survival over hollow glass fibre whips. (Survives better than 35 impacts at midpoint at speed of 40 Km/h) The insulating sheath enables it to be used in environments where there is risk of contact with high voltage sources such as fallen or low-strung power lines. The fully enclosing copper, braided conductor enables a very efficient transfer of radiated power. Two piece construction with rapid assembly/ disassembly enables the antenna to be separated into 2.5m lengths for transport and storage Note: The antenna needs to be used with a suitable Antenna Tuner Unit. Specifications Frequency range: 1.5 to 30 MHz tuneable Input Impedance: 50 Ohms (with suitable tuner) Power Rating: 160 watts Polarisation: Vertical Radiation pattern: Omni-Directional Colour: Matt Black overall Diameter: 15mm Length: 5.0m Weight: 2.8 kg Impact: better than 35 impacts midpoint at speed of 40 km/h) Mounting: Standard mount is via ½ Whitworth stud. (Can be supplied with other base attachment formats or threads) Note: drawing shows base which is not included. 5.0m 2 Section Vehicle Whip HF.doc JB 7th November 2009 35
BP-W-ATU-1.6-30 HF Auto-Tune Antenna 1.6-30 MHz BROADBAND PROPAGATION 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 Designed and constructed for maximum strength and durability, this HF antenna features an electronic automatic tuning system integrated into its base. The antenna /tuner combination offers full frequency coverage from 1.6 to 30 MHz. The only cable connections required are a 50 Ohm coaxial cable and a power supply connection. The electronic tuning system is far superior to older types of mechanical tuners which suffer mechanical breakdown over time. The electronic system also delivers re-tuning times a fraction of what mechanical tuners require. (Less than 10ms memory tuning time for any frequency in the band) It has been designed for Military HF use with a rugged NATO/ US style base. The whip antenna is construction from a lightweight, specialist alloy metal which is extremely strong and very flexible. An insulating cover over the whip allows power line/ voltage protection to 11 kvac Specifications- Electrical Frequency Range: 1.6 to 30 MHz Input Impedance: 50 Ohms VSWR: Less than 2:1 Power Rating: 100 watts CW Polarisation: Vertical Radiation pattern: Omni-Directional Gain: Dependant on frequency Number of Channels: Unlimited Non-Volatile Memory: 168 memory locations Tuning Combinations: ½ Million Initial tune Time: Typical : less than 2 seconds Retune from memory: Typical : less than 10millisecs DC Input requirement: +13.8 VDC(nominal) DC Operating range: +10 to 18.5 VDC Input current :Average: 500 milliamps Specifications- Mechanical Operating Temp: -35 to +70 C Colour: Matt Black overall Whip Diameter: 12.5mm Whip Length: 2.4m Overall length: 2.83m Weight: 3.9 kg Impact: Better than 55 impacts midpoint at a speed of 40 Kms/ Hr. High Voltage: Whip contact protection to11kvac 36 Page 1 of 2 HF_Autotuner_Specs.doc
ENVIRONMENTAL SPECIFICATIONS The BP-W-ATU-1.6-30, HF Auto-Tune Antenna is engineered and manufactured to be compliant with the following MIL-STD-810 Standards. MIL-STD 810F Method 501.4 High Temperature (Both storage and operating) MIL-STD 810F Method 502.4 Low Temperature (Both storage and operating) MIL-STD 810F Method 503.4 Temperature Shock MIL-STD 810F Method 505.4 Solar Radiation (Sunshine) MIL-STD 810F Method 506.4 Rain MIL-STD 810F Method 507.4 Humidity MIL-STD 810F Method 508.5 Fungus MIL-STD 810F Method 509.4 Salt Fog MIL-STD 810F Method 510.4 Sand and Dust MIL-STD 810F Method 514.5 Vibration MIL-STD 810F Method 521.2 Icing, Freezing Rain 37 Page 2 of 2 HF_Autotuner_Specs.doc
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 HF BROADBAND SHIPBOARD WHIP ANTENNA Model: BP-MWT-5-3-30 The BP-MWT-5-3-30 is a ruggedized, 7 metre HF whip antenna and automatic tuner combination designed for shipboard mounting. The combination offers continuous and automatic coverage of the HF Band from 3-30 MHz. The tuner is housed in a fully marinized enclosure and has 150 memory channels enabling rapid tune time. Power rating is 10 to 150 Watts SSB PEP The antenna is vertically polarised and it's radiating element is constructed from heavy duty tapered fibreglass. All metal components are fabricated from marine grade stainless steel. All other exposed surfaces are fully protected against aggressive, marine/ salt spray environments. The antenna is delivered in two pieces and joins with a sturdy threaded connection. A variety of mounting fixtures, constructed from marine grade stainless steel, are available or the mount can be tailored to suit the customer's specific needs. Tuner Specifications Tunable frequency: 3-30 MHz Input impendence: 50 ohms Input power: 10-150W PEP VSWR: <2:1 Power supply voltage: 12V +/- 10% Current consumption: <0.8A Auto tuning time: Approx. 2 seconds (first time tuning) Less than 1 second (return to memory frequency) Memory channels: 150 Weight: 2.0 KG Size: 276mm X 190mm X 96mm (L - W - H) Antenna Specifications Frequency: 2-30 MHz Gain: 0-3 dbi typical VSWR: <2:1 Horizontal Pattern: Omnidirectional Polarisation: Vertical Input connection: 10mm threaded connecting lug Overall length: 7.0m Overall Width: 45mm at base Wind Rating 130 km/hr Mounting: Customer specified mounting Can be supplied with a variety of marine grade stainless steel mounting fixtures 38
Antenna Mounting Options Flange Mount - Marine Grade Stainless Steel Side or Post/ Spigot Mount - Marine Grade Stainless Steel ENVIRONMENTAL SPECIFICATIONS The BP-MWT-5-3-30 is engineered and manufactured to be compliant with the following MIL-STD-810 Standards. MIL-STD 810F Method 501.4 High Temperature (Both storage and operating) MIL-STD 810F Method 502.4 Low Temperature (Both storage and operating) MIL-STD 810F Method 503.4 Temperature Shock MIL-STD 810F Method 505.4 Solar Radiation (Sunshine) MIL-STD 810F Method 506.4 Rain MIL-STD 810F Method 507.4 Humidity MIL-STD 810F Method 508.5 Fungus MIL-STD 810F Method 509.4 Salt Fog MIL-STD 810F Method 510.4 Sand and Dust MIL-STD 810F Method 514.5 Vibration MIL-STD 810F Method 521.2 Icing, Freezing Rain 39
HF BROADBAND SHIPBOARD WHIP ANTENNA Model: BP-MWT-5-3-30 Radiation Patterns 40 HF_Marine_7m_Whip_Tuner_specs.doc, Issue 1022
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BP-LT-45-F BAND-1 LOG PERIODIC ANTENNA Foldable The BP-LT-45-F is a 16 element log periodic antenna covering the Radio Relay Band 1 frequency range of 225-450 MHz, with a mid-band gain of 13 dbi. Front to Back ratio is 28 db Construction is of stainless steel, with stainless steel and Acetal fittings. The antenna folds at its centre to half its length to enable easy transport and storage. Specifications Frequency Range: 225-450 MHz Gain: 10-13dBi Polarisation: Horizontal or vertical F/B Ratio: 28 db Beam Width Vertical: 3 db beamwidth in plane vertical to elements 76 deg. Beam Width Horizontal: 3 db beamwidth in element plane 56 deg VSWR: 2:1 Power Rating 250 watts Input Connection: N type female Mounting: Mounts to 50mm shaft Antenna Length: 1.1 metres Antenna Width: 0.68 metres Antenna Weight: 2.8 kg 41
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 VHF/ UHF DISCONE ANTENNA Model: BPV-LB-108-400 Designed for a variety of base station and tactical applications, the BPV-LB 108-400 is a compact vertically polarised broadband antenna which operates in the frequency range of 108-400 MHz with power handling of 100 watts CW. Mechanical construction of the antenna enables it to withstand the most rugged environmental conditions, with full protection against high wind loads, aggressive salt spray conditions, extreme temperature variation, and wind-borne sand abrasion. The antenna is pole mounted and can be provided with a range of mounting hardware to suit customer requirements. Full connector protection can be provided via a gland-entry weather shroud for marine/ salt spray environments (optional) * Lightning and static discharge protection is provided Specifications Frequency: 108-400 MHz Gain: >2 dbi typical VSWR: Maximum 3:1 across band Radiation Pattern: Omnidirectional Polarisation: Vertical Power Rating : 150 watts average (CW continuous) Input Impedance: 50 ohms Input connection: N type Female Wind Velocity Rating: 180 km/hr Operational Temp: -40 to +70 deg. C Storage Temp: -40 to +70 deg. C Overall length: 1.2m Overall Width: 0.85m (ground-plane diameter) Weight: 5.5 Kg Finish: Black/ Grey Epoxy- Glass Mounting: Mounts to any circular spigot or tube 30-50mm Diameter (Or to customer requirement) 42 VHF_UHF 108-400 Discone.doc, Issue 0908
VSWR PLOT HF_UHF 108-400 Discone.doc, Issue 0908 43
44 HF_UHF 108-400 Discone.doc, Issue 0908
VHF UHF/ Discone BPV-LM-108-400 Gain versus frequency Plot Total gain dbi HF_UHF 108-400 Discone.doc, Issue 0908 45
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BP-LT-20-200-F LOG PERIODIC ANTENNA Foldable The BP-LT-20-200-F is an 11 element log periodic antenna covering the frequency range of 25-200 MHz, with a midband gain of 7 dbi. Front to Back ratio is 11 db. Construction is of aluminium, with stainless steel and Acetal fittings. The elements are detachable and for ultra fast deployment, a spring loaded bayonet locking system enables each element to positively fasten/ unfasten to the boom with only a half-turn twist. The antenna elements are constructed from a specialised aluminium Alloy which has very high tensile strength and durability. The antenna folds at its centre to half its length to enable easy transport and storage. A canvas carry bag is supplied with the antenna. Specifications Frequency Range: 20-200 MHz Gain: 4-7dBi Input Impedance: 50 Ohms Polarisation: Horizontal or vertical F/B Ratio: 11 db VSWR: Better than 3:1 Power Rating 200 watts CW Input Connection: N type female Mounting: Mounts on 30-50mm diameter shaft or spigot No. of Elements: 11 Antenna Length: 3.5 metres Antenna Width: 5.8 metres Antenna Weight: 11 kg 46
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47143178438 BPB-30-108 ELEVATED WIDEBAND VHF ANTENNA The BPB-30-108 is a rugged broadband antenna designed for high performance in the VHF band, 30-108 Mhz. The antenna is used for tactical applications using portable masts or for base-station mounting on towers or other fixed platforms. It is best suited for applications where increased range is needed to communicate with backpack and vehicle mounted radios from a fixed base location. Power rating is 100 watts continuous, and gain over the band is comparable to a tuned ¼ wave whip antenna. Tuning is automatic and all tuning elements are incorporated within the antenna. The antenna elements break down for shipping and assemble together easily on-site. A range of mounting options can be provided to suit the customers existing pole or mast equipment. Specifications Frequency range: Power Rating: Radiation pattern: Gain: VSWR: Polarisation: Input Impedance: Input connector: Element Diameter: Overall height: Temperature Rating: Wind Rating: Weight: Mounting: 30 to 108 MHz (no tuner needed) 100 watts CW Omnidirectional (horizontal) Average 0dBi across the band Better than 3.5:1 across the band Vertical 50 Ohms N type Female 12.5mm 2.5m from top of mast (top element) with 3 x 2.3m counterpoise elements extending below -40 to +70 deg. C operational 170 Kph 2.9 Kg To customer specification 47
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BP-LP-38-T VHF LOG PERIODIC ANTENNA - Transportable The BP-LP-38-T is an 11 element log periodic antenna covering the VHF Band of 30 to 88 MHz, with a mid-band gain of 7dBi. And Front to Back ratio of 11dB Construction is of aluminium, with booms which disassemble for transport, The antenna elements also easily detach to enable the whole antenna to be reduced to a compact package for transport and storage. The antenna elements are fabricated from a special, ultra-high tensile Aluminium tubing which has a strength to weight ratio far exceeding tube steel or fibreglass (comparable to carbon fibre). Vertical and Horizontal polarisation modes are provided for. Mounting is via a standard 40mm spigot or alternative mounting can be provided if desired. The antenna is supplied with a sturdy canvas carry bag. Specifications Frequency Range: 30-88 MHz Impedance: 50 Ohms Gain: 4dBi Minimum to 7dBi Maximum Polarisation: Horizontal or Vertical F/B Ratio: 11 db Beam Width E Plane 88 Deg. H plane 110 Deg. Typical (Frequency. dependant) VSWR: Better than 3:1 Power Rating 400 watts PEP Input Connection: N type female (socket) Mounting: 40mm diameter mounting spigot No. of Elements: Eleven Antenna Length: 3.3 metres Antenna Width: 3.2 metres, At widest point Antenna Weight: 12 kg including carry bag 48
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BP- VHF-UHF-RD VHF/ UHF HANDHELD TRANSCEIVER ANTENNAS Compressed Helical Type A range of compressed helical rubber ducky whips for use with hand held transceivers operating in the VHF and UHF range The copper coated radiating element is covered in a protective poly-olefin shroud and is provided with a sturdy mounting base. This is a rugged, tough, antenna designed for use in tactical combat in all types of operating conditions from arctic through to extreme desert environments. Broadband Propagation manufactures to customer specifications including diameter, length, frequency range and mounting connector.. Fully corrosion resistant. Sand abrasion resistant. Fungal attack protected. UV stable. Specifications Frequency Range: To Order Impedance: 50 Ohms Radiation Pattern: Omni-Directional Polarisation: Vertical VSWR: Better than 3:1 Power Rating: 10 watts CW Input Connection: To Order Antenna Length: To Order Antenna Width: To Order Temperature Rating: -40 to +70 deg C Impact Rating: Over 1500 impacts to 90 Deg flexure without failure. 49
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 MP-136-174-BF VHF Manpack Antenna The MPB-136-174 BF VHF Manpack Antenna covers the frequency Range from 136 MHz to 174 MHz No external tuning or adjustment is required for a 50 Ohm impedance match across this bandwidth. The antenna is designed for use with modern, military man-pack radios. It is both light-weight and extremely robust in its design and highly suitable for the most demanding of tactical applications, across the full range of environmental conditions. It can be supplied with an optional flexible gooseneck. * * * Broad-Band Frequency Range * * * * * * No Tuning or Adjustment Required * * * * * * Light and Rugged Construction * * * Specifications Frequency range: Input Impedance: Power Rating: VSWR: Gain: Polarisation: Radiation pattern: Input Connector: Colour: Diameter: Length: Length, Folded: Weight: Operating Temp. 136 to 174 MHz 50 Ohms 40 watts CW 2.0:1 Maximum. 0 dbi Vertical Omni Directional TNC Male Matt Black overall 12.5 mm 830mm Overall, Operating Length 415mm 0.15 kg -40 C to +70 C (Whip can be supplied with other antenna to base attachment formats or threads, and other base styles) Optional Flexible Gooseneck 50
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 PRA-350-450 VHF/UHF Personal Radio Antenna The PRA-350-450 VHF/UHF Personal Radio Antenna is a versatile antenna offering good gain and optional mounting positions to maximize circuit range according to the users operational requirements. It is ground independent and can be used attached directly to the radio or via a supplied length of coaxial cable with the antenna mounted in a higher position. The antenna is designed for use with modern, military hand held radios. It is both light-weight and extremely robust in its design and highly suitable for the most demanding of tactical applications, across the full range of environmental conditions. It can be supplied with an optional antenna extension rod. This rod is attached to the soldier's back on his vest and the antenna sits with most of it's radiating length above shoulder level. The antenna position and height gives a much improved communication range. Broad instantaneous bandwidth Increased performance over standard stubby whip antenna when directly mounted to antenna. Even better performance when mounted high using extension rod and coax. Specifications Frequency range: Input Impedance: Power Rating: VSWR: Gain: Polarisation: Radiation pattern: Input Connector: Colour: Diameter: Length: Weight: Operating Temp. 350 to 450 MHz 50 Ohms 10 watts CW continuous 3.5:1 Maximum. (much better than this across most of the band) 2-2.5 dbi (effective gain much higher than standard antenna due to it's better gain and increased height) Vertical Omni Directional SMA Matt Black overall 10 mm 390 mm 0.35 kg -40 C to +70 C (Whip can be supplied with other antenna to base attachment formats or threads, and other base styles) 51
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BP-VHF-2-STW BACKPACK TAPE WHIP ANTENNAS Broadband Propagation manufactures a range of light-weight, flexible, tape whip antennas for use with VHF man-pack transceivers. Standard length is one metre. Designed for use in tactical combat, in all types of operating conditions from arctic through to extreme desert environments they are constructed of highly durable, long-life, spring steel elements which will not break or lose their set. A flexible nylon braid covers the whip, increasing durability and providing high voltage contact protection. Antenna mounting connectors including thread, BNC, N, or C type can be provided or customer specified mountings can be supplied. The antenna is supplied with a goose neck base allowing for instant angle adjustment. Specifications Frequency Range: Impedance: Radiation Pattern: Polarisation: Power Rating: Input Connection: Antenna Length: Antenna Width: Antenna Weight: Temperature Rating: 30-100 MHz Nominal Omni-Directional Vertical 10 watts CW Customer specified 1.0 metres 13 mm 130 grams -40 to +70 deg C Fully Flexible. Integral Goose Neck. Fully corrosion resistant. Sand abrasion resistant. Fungal attack protected. UV stable. Customer Specified Mounting 52
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPV-30-512 VHF/UHF Vehicle Whip The BPV-30-512 is a ruggedly constructed whip antenna which covers the frequency range of 30 MHz to 512 MHz without the need for any external tuning or adjustments. Construction of the whip features a specialised element material offering more efficient transfer of radiated power and increased impact survival and durability compared with hollow glass fibre whips. (Survives better than 70 impacts at midpoint at speed of 40 Km/h) Supplied in two sections, the whip features a unique snap-lock joiner for deployment to full length. The antenna has an extremely rugged base suitable for all types of mobile platforms. The base has provision for UK/ NATO 6, or 3 hole pattern and USA 4 hole pattern mounting Specifications Frequency range: 30 to 512 MHz Input Impedance: 50 Ohms Power Rating: 50 watts CW VSWR: < 3.5:1 over band Gain: -1dBi to +4dBi over band Polarisation: Vertical Radiation pattern: Azimuth 360 deg, (Omni Directional) Input Connector: N type female (other connectors including BNC available) Colour: Matt Black overall Diameter: 12mm Length: 2.7m Weight: 3.0 kg Operating Temp. -40 C to +70 C Impact Rating: Better than 70 impacts midpoint at speed of 40 km/h Mounting: Standard antenna to base mount is via ½ Whitworth stud. (Whip can be supplied with other antenna to base attachment formats or threads, and other base styles) Antenna mounted on 3 x 3m conductive platform Antenna Base NATO/ USA 4 hole pattern mounting 53
BPV-30-512 VHF Broadband VHF/ UHF Vehicle Whip Antenna mounted vertically on 3m x 3m conductive base plane Representative Radiation Patterns Note: Frequencies are in MHz 54
BPV-30-512 VHF Broadband VHF/ UHF Vehicle Whip Antenna mounted vertically on 3m x 3m conductive base plane Representative Radiation Patterns Note: Frequencies are in MHz 55
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BPV-30-108 VHF Mobile/ Vehicle Whip Antenna & Base This is a broadband antenna designed for high performance in the VHF band 30-108Mhz. Power rating is 100 watts continuous, and gain over the band is comparable to a tuned ¼ wave whip antenna. Tuning is automatic and all tuning elements are incorporated within the antenna and base. Fabricated from fibreglass, the antenna has high impact survival and is lightweight and rugged. The antenna whip is used in conjunction with a rugged base unit with heavy duty stainless steel spring. The base is fitted with mounting holes of UK/Nato 6 hole, or USA 4 hole pattern. It is extremely rugged and is Designed to meet MIL-STD 810 and Australian Defence Standard DEF-STAN 00-35. Specifications Frequency range: Power Rating: Radiation pattern: 30 to 108 MHz continuous (without tuner) 100 watts Omnidirectional (with some variation according to vehicle type and mounting position) Better than 2.5:1 across most of band Vertical 50 Ohms BNC 12.5mm 2.74m from bottom of whip. Better than 100 impacts at the midpoint of the antenna at 40 kph. UK/Nato 6 hole, or USA 4 hole pattern Matt Black overall 11 kvac VSWR Polarisation: Input Impedance: Input connector: Whip Diameter: Overall height: Impact Survival: Mounting: Colour: High voltage whip contact protection: Environmental: Ambient temperatures -21 to +70C; DEF-STAN 00-34, test CL1 and test CL4 Relative humidity 98%; DEF-STAN 00-35 Altitude 3,00m ASL; DEF-STAN 00-35 Immersion 1.5m; DEF-STAN 00-35 Driving Dust DEF-STAN 00-35 Corrosion/Salt DEF-STAN 00-35 Contamination DEF-STAN 00-35 Drop DEF-STAN 00-35 Vibration DEF-STAN 00-35 56
Pty. Ltd. ACN: 143 178 438 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 Adelaide, BPV-25-500 VHF/ UHF Vehicle Whip This is a broadband antenna designed for high performance in the VHF/ UHF bands 25-500Mhz. Power rating is 100 watts continuous, and gain over the band is comparable to a tuned ¼ wave whip antenna. Tuning is automatic and all tuning elements are incorporated within the antenna and base. Fabricated from fibreglass, the antenna has high impact survival and incorporates high voltage power line protection via a Polyolefin outer jacket covering the full length of the antenna.. The antenna whip is used in conjunction with a rugged base unit with heavy duty stainless steel spring. The base is fitted with mounting holes of UK/Nato 6 hole, or USA 4 hole pattern. Specifications Frequency range: Power Rating: Radiation pattern: Gain: VSWR: Polarisation: Input Impedance: Input connector: Whip Diameter: Overall height: Impact Survival: Mounting: Colour: 30 to 500 MHz (without tuner) 100 watts Omnidirectional (with some variation according to vehicle type and mounting position) 25MHz min. -10dBi, 100MHz min. 0dBi, 500MHz min. +2dBi Better than 3:5:1 at 25MHz, 2.0:1 at 100MHz and 2.0:1 at 500MHz Vertical 50 Ohms BNC Female 12.5mm 3.25m (including base) Better than 80 impacts at the midpoint of the antenna at 40 kph. UK/Nato 6 hole, or USA 4 hole pattern Mil Spec painted to customer designated colour The antenna is designed and constructed to meet the requirements of the following standards Mil-Std-810F, Method 501.4 Mil-Std-810F, Method 502.4 Mil-Std-810F, Method 507.4 Mil-Std-810F, Method 505.4 Mil-Std-810F, Method 506.4 Mil-Std-810F, Method 500.4 Mil-Std-810F, Method 509.4 Mil-Std-810F, Method 510.4 Mil-Std-810E, Method 514.4 Mil-Std-810F, Method 514.5 Mil-Std-810F, Method 516.5 Mil-Std-810F, Method 504 Antenna Base includes mounting holes to suit UK/Nato 6 hole or USA 4 hole pattern 57
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 VHF/ UHF DISCONE ANTENNA Model: BPV-LB-100-400 Designed for a variety of base station and tactical applications, the BPV-LB 100-400 is a compact vertically polarised broadband antenna which operates in the frequency range of 100-400 MHz with power handling of 500 watts CW. Mechanical construction of the antenna enables it to withstand the most rugged environmental conditions, with full protection against high wind loads, aggressive salt spray conditions, extreme temperature variation, and wind-borne sand abrasion. The antenna is pole mounted and can be provided with a range of mounting hardware to suit customer requirements. Full connector protection can be provided via a gland-entry weather shroud for marine/ salt spray environments (optional) * Lightning and static discharge protection is provided Specifications Frequency: 100-400 MHz Gain: 2 dbi typical VSWR: Maximum 2:1 across band Horizontal Pattern: Omnidirectional Polarisation: Vertical Power Rating : 500 watts average (CW continuous) Input Impedance: 50 ohms Input connection: N type Female Overall length: 0.8m Overall Width: 1.3m (ground-plane diameter) Wind Rating 230 km/hr Mounting: Mounts to any circular spigot or tube 30-50mm Diameter (Or to customer requirement) VHF_UHF Discone.doc, Issue 0904 58
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47143178438 BPB-450-500 ELEVATED WIDEBAND FIXED STATION UHF ANTENNA The BPB-450-500 is a rugged broadband antenna designed for high performance in the UHF band, 450-500 Mhz. The antenna is used for permanent base-station mounting on towers or other fixed platforms. Power rating is 50 watts continuous, and gain over the band is comparable to a tuned ¼ wave whip antenna. Tuning is automatic and all tuning elements are incorporated within the antenna. The antenna elements break down for shipping and assemble together easily on-site. A range of mounting options can be provided to suit the customers existing pole or mast equipment. The antenna is designed and built using construction methods and materials that ensure maximum operational life in the full range of adverse environmental conditions from arctic to tropical. Specifications Frequency range: Power Rating: Radiation pattern: Gain: VSWR: Polarisation: Input Impedance: Input connector: Element Diameter: Overall height: Temperature Rating: Wind Rating: Weight: Mounting: 450 to 500 MHz (no tuner needed) 50 watts CW Omnidirectional (horizontal) Average 0dBi across the band Better than 2:1 across the band Vertical 50 Ohms N type Female 12.5mm 0.35m from tip of top element to bottom of radials -40 to +70 deg. C operational 250 Kph 1.7 Kg To customer specification 59
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 MP-225-2G Wide-Band Man-pack Antenna The MP-225-2G is a wide-band antenna covering the full spectrum from 225 MHz to 2000 MHz No external tuning or adjustment is required. The antenna is ground plane independent and contains no power absorbing networks, ensuring maximum radiation efficiency across its bandwidth. The antenna is designed for use with modern, wideband, military man-pack radios and is supplied with a flexible gooseneck mount. It is both light-weight and extremely robust in its design and highly suitable for the most demanding of tactical applications, across the full range of global environmental conditions. A GRP radome encloses the radiating elements and the gooseneck mount is fitted as standard with an N type connector but a range of other connector fittings can be supplied, according to the customer s requirements. * * * Wide-Band Frequency Range * * * * * * No Tuning or Adjustment Required * * * * * * Light and Rugged Construction * * * Specifications Frequency range: Input Impedance: Power Rating: VSWR: Gain: Polarisation: Radiation pattern: Input Connector: Colour: Diameter: Length: Weight: Operating Temp. 225 to 2000 MHz 50 Ohms 25 watts CW 3.0 Typical -5dBi to +4dBi over band Vertical Azimuth 360 deg, (Omni Directional) N type (other connectors available) Customer to specify type and gender Matt Black overall 30 mm 650mm 0.48 kg -40 C to +70 C (Whip can be supplied with other antenna to base attachment formats or threads, and other base styles) Flexible Gooseneck Mount 60
Note: Gain is in dbi MP-225-2G Wide-Band Antenna Vertical (E Plane) Radiation patterns 61
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 VHF/ UHF SHIPBOARD DISCONE ANTENNA Model: BPV-SPB-100-400 Designed for shipboard mounting, the BPV-SPB 100-400 is a compact vertically polarised broadband antenna which operates in the frequency range of 100-400 MHz with power handling of 300 watts CW. Antenna radiating elements are of marine grade stainless steel with a grey polyurethane lacquer finish. All other exposed surfaces are fully protected against aggressive, marine/ salt spray environments. The antenna is pole mounted and can be provided with a range of mounting hardware to suit customer requirements. * Full connector protection is provided via gland-entry weather shroud * Lightning and static discharge protection is provided Specifications Frequency: 100-400 MHz Gain: 2 dbi typical VSWR: Maximum 2:1 across band Horizontal Pattern: Omnidirectional Polarisation: Vertical Power Rating : 300 watts average (CW continuous) Input Impedance: 50 ohms Input connection: N type Female Overall length: 0.8m Overall Width: 1.3m (ground-plane diameter) Wind Rating 230 km/hr Mounting: Mounts to any circular spigot or tube 30-50mm Diameter (Or to customer requirement) VHF_UHF Marine Discone.doc, Issue 0903 62
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 BP25-13-186 BAND-3 CORNER REFLECTOR ANTENNA - Foldable MANUAL & SPECIFICATIONS Corner Reflector 6 element_manual.doc 6/July/2009 Page 1 of 5 63
1. Description The BP25-13-186 is a high-gain corner reflector antenna for Radio Relay Band 3 (1350-1850 MHz). Side and back-lobes are highly attenuated. The antenna features low mass, low wind loading, rugged construction, and can be quickly folded flat for transport and storage. The antenna may be mounted horizontally for horizontal polarisation, or vertically for vertical polarisation. Construction is of aluminium, stainless steel and acetal, with stainless steel mounting fittings. 2. Mounting The antenna is designed to be mounted on a 50mm OD support and can be mounted on the support vertically or horizontally, for vertical or horizontal polarisation. Corner Reflector 6 element_manual.doc 6/July/2009 Page 2 of 5 64
3. Folding the Antenna Two acetal clasps hold the antenna in its open position as shown below. To fold the antenna these clasps are pulled outward and the two end plates are folded inward. Velcro straps at the centre of the antenna hold it in the folded position. Antenna in the operating position showing clasps in locked position. Partly folded antenna. Note that the end plates fold inward. Corner Reflector 6 element_manual.doc 6/July/2009 Page 3 of 5 65
4. Specifications 4.1 Electrical Frequency Range: 1350-1850 MHz Gain: > 18 dbi across operating band Polarisation: Horizontal or vertical F/B Ratio: E Plane >30 db 0/90-270 deg. H Plane >30 db 0/90-270 deg. 3dB (half power) Beam Width: E Plane 6-12 deg. H Plane 40-52 deg VSWR: < 2:1 Power Rating: 25 watts Input Connection: N type female 4.2 Mechanical Mounting: Dimensions Operating: Folded: Antenna Weight: 4.3 Environmental Temperature: Wind Speed Maximum: Wind Load: Mounts to 50mm shaft/ boom 1105 x 290 x 455mm 1105 x 355 x 80mm 5 kg -40 deg C to 90 deg C 40 m/s 360 N (at 30 m/s) 4.4 Radiation Patterns P25-13-186; 3D Free-Space Radiation Pattern @ 1600 MHz Corner Reflector 6 element_manual.doc 6/July/2009 Page 4 of 5 66
Free-Space, E Plane Radiation Pattern @ 1600 MHz Free-Space, H Plane Radiation Pattern @ 1600 MHz Corner Reflector 6 element_manual.doc 6/July/2009 Page 5 of 5 67
Pty. Ltd. ACN: 143 178 438 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 Adelaide, BPV-DB-800-1700 Dual Band UHF Vehicle Whip This is a dual band antenna covering 800-960 MHz (instantaneous bandwidth of 160 MHz) via one input and 1700-2200 MHz (instantaneous bandwidth of 500 MHz) via another. Power rating is 200 watts continuous at both inputs. The antenna is ground independent and each frequency band operates independently and simultaneously. This antenna is two separate antennas collinearly configured on one mounting base in a design which is exceptionally rugged and capable of reliable operation in the most adverse of tactical environments. High impact survival is a major feature. The antenna is mounted on a rugged base unit with heavy duty stainless steel spring. The base is fitted with mounting holes of UK/Nato 6 hole, or USA 4 hole pattern. Specifications Frequency range, band "a" Frequency range, band "b" Power Rating: Radiation pattern: Gain: VSWR: Polarisation: Input Impedance: Input connectors: Height: Mounting: Colour: 800 to 960 MHz 1700 to 2200 MHz 200 watts band "a", 200 watts band "b" Omnidirectional Minimum 3 dbi for both "a" and "b" bands Better than or equal to 2.0:1 for both "a" and "b" bands Vertical 50 Ohms 2 x TNC type female 425mm Overall UK/Nato 6 hole, or USA 4 hole pattern Mil Spec painted to customer designated colour The antenna is designed and constructed to meet the requirements of the following standards Mil-Std-810F, Method 501.4 Mil-Std-810F, Method 502.4 Mil-Std-810F, Method 507.4 Mil-Std-810F, Method 505.4 Mil-Std-810F, Method 506.4 Mil-Std-810F, Method 500.4 Mil-Std-810F, Method 509.4 Mil-Std-810F, Method 510.4 Mil-Std-810E, Method 514.4 Mil-Std-810F, Method 514.5 Mil-Std-810F, Method 516.5 Mil-Std-810F, Method 504 Antenna Base includes mounting holes to suit UK/Nato 6 hole or USA 4 hole pattern 68
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 HGO-2400-2500 High Gain Omnidirectional Antenna The HGO-2400-2500 High Gain Omnidirectional Antenna Operates in the Wi-Fi band between 2.4 GHz and 2.5 GHz and is ruggedized to operate in a range of adverse outdoor conditions. It is a ground independent collinear antenna and can be mounted on a variety of platforms including vehicles and shelters. It exhibits good VSWR across its full bandwidth and has high omnidirectional gain in the horizontal (H) plane with minimal side-lobes. Peak gain is 12 dbi. It can be fitted with a variety of connectors including Reverse Polarity TNC plug Specifications Frequency range: 2400 to 2500 MHz Input Impedance: 50 Ohms Power Rating: 50 watts Nominal VSWR: 1.5:1 (average across band, max 1.9:1) Gain: Polarisation: Radiation pattern: Input Connector: Colour: Diameter: Length: Weight: Operating Temp. 12 dbi maximum Vertical, Linear Highly directional in vertical (E) plane, Omni Directional in horizontal (H) plane RP-TNC (Reverse Polarity TNC) plug Matt Black overall 4 cm 110 cm 1.45 kg -40 C to +70 C Supplied with Marine Grade Stainless steel parallel mounting clamp 69
Pty. Ltd. ACN: 143 178 438 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 Adelaide, BPV-L-960-1240 UHF Vehicle Whip This is a broadband antenna covering 960-1240 MHz with a power rating of 100 watts continuous. The antenna is ground independent. The antenna is mounted on a rugged base unit with heavy duty stainless steel spring. The base is fitted with mounting holes of UK/Nato 6 hole, or USA 4 hole pattern. The major design goal for this antenna is maximum ruggedness and durability in all operating conditions. This antenna is suitable for all types of vehicle mounting including Tank mounting. From it's high strength Polyoxymethylene (POM) Radome to it's heavy duty spring and base this antenna will withstand the most extreme operating environments. - - - - Over-engineered for ultimate strength and reliability - - - - Specifications Frequency Range: 960 to 1240 MHz Power Rating: 100 Watts Radiation pattern: Omnidirectional Gain: Minimum 3 dbi VSWR: Better than or equal to 2.0:1 Polarisation: Vertical Input Impedance: 50 Ohms Input connectors: TNC type female Height: 300mm Overall Width: 40mm antenna width, 140mm mounting-base flange width Mounting: UK/Nato 6 hole, or USA 4 hole pattern Colour: Matt Black The antenna is designed and constructed to meet the requirements of the following standards Mil-Std-810F, Method 501.4 Mil-Std-810F, Method 502.4 Mil-Std-810F, Method 507.4 Mil-Std-810F, Method 505.4 Mil-Std-810F, Method 506.4 Mil-Std-810F, Method 500.4 Mil-Std-810F, Method 509.4 Mil-Std-810F, Method 510.4 Mil-Std-810E, Method 514.4 Mil-Std-810F, Method 514.5 Mil-Std-810F, Method 516.5 Mil-Std-810F, Method 504 Antenna Base includes mounting holes to suit UK/Nato 6 hole or USA 4 hole pattern 70
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 L BAND 500-2000 MHz SHIPBOARD ANTENNA Model: BP-ML-500-2000 Designed for shipboard mounting, the BP-ML -500-2000 is a vertically polarised broadband antenna which operates in the frequency range of 500-2000 MHz with power handling of 110 watts. The antenna is ground independent and has good efficiency across the bandwidth. The antenna radiating elements are enclosed within a cylindrical, protective fibreglass radome with polyurethane lacquer finish. The mounting post is of marine grade stainless steel The antenna is pole or flange mounted and can be provided with a range of mounting hardware to suit customer requirements. *Full-band instantaneous operation available with single RF input. *Full connector protection provided via gland-entry weather shroud *Lightning and static discharge protection provided Specifications Frequency: 500-2000 MHz Gain: 2 dbi typical VSWR: Maximum 2.5:1 across band Horizontal Pattern: Omnidirectional Polarisation: Vertical Power Rating : 110 watts Input Impedance: 50 ohms Input connection: N type Female Wind Rating: 210 km/hr Operational Temperature: -20 deg C to +55 deg C Storage Temperature: -20 deg C to +70 deg C Overall length: 1.2m Overall Width: 40mm Weight: 1.1 kg (excluding mounting) Shipping weight: 2.0 kg (including mounting) Shipping Size: 1.3m x 0.2m x 0.2m Mounting: Marine grade stainless steel flange or pole/ spigot mounts available (Or to customer requirement) 71
L BAND 500-2000 MHz SHIPBOARD WHIP ANTENNA Mounting Options Flange Mount - Marine Grade Stainless Steel Side or Post/ Spigot Mount - Marine Grade Stainless Steel L BAND 500-2000 MHz SHIPBOARD ANTENNA Model: BP-ML-500-2000 ENVIRONMENTAL SPECIFICATIONS The BP-ML-500-2000 is engineered and manufactured to be compliant with the following JSS 55555 Standards, as per table N1 of JSS 55555, covering the following tests. 1 Vibration Test 2 High Temperature (operational and storage) 3 Damp Heat 4 Low Temperature (operational and storage) 5 Drip Proof 6 Tropical Exposure 7 Mould Growth 8 Corrosion 9 Toppling 10 Bump Test 11 Shock or Impact test 72
L BAND 500-2000 MHz SHIPBOARD WHIP ANTENNA Radiation Patterns Note: These Patterns are derived with the antenna unencumbered by Ship superstructure or other nearby antennas. 73 L Band Marine Whip.doc, Issue 1005C
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 84 232 273 647 L BAND 960-2000 MHz SHIPBOARD ANTENNA Model: BP-ML-960-2000 Designed for shipboard mounting, the BP-ML -960-2000 is a vertically polarised broadband antenna which operates in the frequency range of 960-2000 MHz with power handling of 110 watts. The antenna radiating elements are of marine grade stainless steel and the entire antenna structure is enclosed within a cylindrical, protective fibreglass radome with grey polyurethane lacquer finish. The mounting post is of marine grade stainless steel The antenna is pole or flange mounted and can be provided with a range of mounting hardware to suit customer requirements. *Full-band instantaneous operation available with single RF input. *Full connector protection provided via gland-entry weather shroud *Lightning and static discharge protection provided Specifications Frequency: 960-2000 MHz Gain: 2 dbi typical VSWR: Maximum 2:1 across band Horizontal Pattern: Omnidirectional Polarisation: Vertical Power Rating : 110 watts Input Impedance: 50 ohms Input connection: N type Female Overall length: 0.5m Overall Width: 0.32m Wind Rating 210 km/hr Mounting: Mounts to any circular spigot or tube 30-50mm Diameter (Or to customer requirement) 74 VHF_UHF Marine Discone.doc, Issue 1004
Pty. Ltd. CAN: 143178438 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47143178438 BROADBAND PROPAGATION PNEUMATIC MAST SERIES The Broadband Propagation range of pneumatic masts are suitable for a large variety of purposes including the mounting of antennas, lighting, scientific and industrial monitoring, equipment, photographic and surveillance equipment, as well as a wide variety of other applications. Our extensive range of models cover payload requirements from 15 kg up to 500 kg with fully extended heights available in a range from 3.2 meters up to 21 meters. Construction is of specially processed, high tensile strength aluminium, with low friction collar bearings assuring ruggedness, smooth operation and dependability, at high usage rates, over a long product life. Anodised finish on all exposed surfaces of the masts guarantees superior corrosion and weather resistance. Rotation of mast tubes in the horizontal plane is prevented via keying along the full length of the mast. Models with locking and non locking collars are available Customized models catering to customer specific requirements are also available. **** For full specifications of our product range please go to our website. www.broadbandpropagation.com 75
BPV-TM Tactical Mast Series BROADBAND PROPAGATION Pty. Ltd. 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 The BPV-TM series of tactical, field deployable masts are of composite construction and feature strength and ruggedness combined with very low weight. The masts are push-up and can be extended and retracted quickly and easily. The clamping system is moulded from high strength polymer and allows for one handed operation. It exerts strong locking force on the mast sections and a clamp guard is incorporated to prevent accidental release The 9.4m mast is constructed of glass composite, the 10m of glass/ carbon-fibre hybrid and the 45m mast is of carbon-fibre. It comes complete with guys, guying stakes, base plate and mallet in a canvas carry bag. Mounting kits for vehicles and shelters are available and can be tailored to meet customer needs. The mast series is suitable for light head-loads such as tactical HF wire antennas and VHF/ UHF omnidirectional antennas. The mast head can be fitted with a variety of antenna mounting adaptors. Please specify the type of mount required when ordering Model No. 30-7 35-8 45-9 No. of Sections 7 8 9 Extended Height 9.4m (30ft) 10m (35ft) 14m (45ft) Retracted Height 1.8m 1.8m 2.1m Guying Radius 5.5m 6m 7.5m Mast Weight 3.4kg 3.35kg 4.7kg Accessories Weight 4kg 5kg 5kg Construction Glass composite Glass/ carbon composite Carbon composite Everything required for erection of the mast is included. 76
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 47143178438 BPM-12-AL-H 12m Guyed Aluminium Tube Mast The BPM-12-AL-H Guyed Aluminium mast is a cost effective solution for the support of HF wire antennas as well as VHF and UHF and Microwave antennas. The mast is particularly suitable for mounting all varieties of HF wire antennas, either as "Inverted V" and "Sloper" configurations (one mast kit required), or horizontally (two mast kits required) A horizontal arm (gibbet) which fits at the top of the mast can be supplied for "Inverted V" mounting of wire antennas The BPM-12-AL-H is assembled from 2m sections of high strength aluminium tubing, with collared end joints, for quick and easy assembly. Once the base mount and guy anchors have been installed it is a simple matter to push fit the mast sections together, raise the mast and tension the guys. A pulley and 24 metres of high quality UV stable halyard rope is supplied with each mast kit. Each mast is delivered as a kit and includes 1 Mast sections 2 guying cables, 3 pivoting foot mount, 4 ground anchor equipment, 5 pulley and halyard rope If a horizontal mounting arm (gibbet) is required please specify in your order. Specifications No. of Sections: 6 Max Extended Height: 12.0 metres Section Length: 2m Guying: 5mm non-conductive (RF transparent) guy cable Shipping Weight: Shipping Size: 35 Kilograms 1 of 160mm x 2.2 m tube 1 of 400mm x 400mm x 250mm box Max Wind Speed: 150 Km/Hr This is a perfect mast solution, it is has a low purchase price, is easy to install and it's compact packed size and light weight means shipping costs are minimal! 77
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BROADBAND PROPAGATION 15 Metre GUYED BUTT MAST 15 m Hot-Dip Galvanised Steel, Triangular Lattice Guyed Mast designed specifically for mounting the BPA range of centre fed wire antennas either horizontally or as Inverted V Purpose Built Strong and Durable Welded Steel Construction Hot Dip Galvanised. After Fabrication for Ultimate Corrosion Protection. Guying Cables Supplied Broken Into Sections With Insulators To Suit HF Antenna Mounting Specifically Designed To Minimise Shipping Weight Yet Maintain Required Strength All Fittings Supplied For Inverted Vee Antenna Mounting Swivel Base For Easy Erection Using a Gin Pole and Winch or Vehicle 78
1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 ABN: 84 232 273 647 BROADBAND PROPAGATION 15.9 Metre GUYED BUTT MAST 15.9 m Hot-Dip Galvanised Steel, Triangular Lattice Guyed Mast, The tower is shipped in five 3.0m sections which bolt together. A 50mm diameter steel top tube is supplied for increased antenna mounting flexibility. Purpose Built Strong and Durable Welded Steel Construction Hot Dip Galvanised. After Fabrication for Ultimate Corrosion Protection. Guying Cables And All Fittings Supplied Specifically Designed To Minimise Shipping Weight Yet Maintain Required Strength All Fittings Supplied For Inverted Vee Antenna Mounting Swivel Base For Easy Erection Using a Gin Pole and Winch or Vehicle Shipping Weight: 2.2 Tonnes, Shipping Size: L 3.2m x W 1.2m x H 0.8m 79
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 BROADBAND PROPAGATION BPGLASS WIRE HIGH TENSILE STRENGTH LOW WEIGHT NON MAGNETIC RF TRANSPARENT ELECTRICALLY INSULATING CORROSION & ELONGATION PROOF TEMPERATURE PROOF TO - 32 deg C **** Contact us for the very best price on this product **** Many antenna (and other) applications call for support structure guying which is not electrically conductive and which will not couple with Radio Frequency energy. We can supply long life, high strength, guying cable which is transparent to RF and corrosion and elongation proof at a cost comparable with equivalent strength steel cable. Array Guying Because our cable is totally resistant to corrosion it is also ideal for use in critical environments such as seawater or other corrosive fluid environments. Enquire about our prices..you will be surprised! Mast & Tower Guying ORDER CODE: BPW-DB-4 BPW-DB-5 BPW-DB-6 BPR-DB-4 BPR-DB-5 BPR-DB-7 Outside Diameter 4 mm 5 mm 6 mm 4 mm 5 mm 7 mm Weight/Meter 20 grams 32 grams 44 grams 19 grams 30 grams 52 grams Tensile Strength 430 KG 560 KG 970 KG 240 KG 340 KG 460 KG 80
Comparison of Wire Strength Core dia. 4 mm Ø 5 mm Ø 6 mm Ø 7 mm Ø Weight of 200 mm length Tensile strength kg. Core dia. Weight of 200 mm length Tensile strength kg. Core dia. Weight of 200 mm length Tensile strength kg. Core dia. Weight of 200 mm length Tensile strength kg. BPGLASS Wire 2.5 3.9 430 3.0 6.3 560 4.0 8.8 970 -- -- -- DEBEGLASS Wire 2.5 3.9 430 3.0 6.3 560 4.0 8.8 970 -- -- -- BPGLASS Rope 1.8 3.8 240 2.3 5.9 340 -- -- -- 2.8 10.4 460 Steel Wire 2.5 5.6 370 3.15 9.3 530 4.0 14.5 850 5.0 22.0 1340 Polyethylene Rope 4.0 1.66 180 5.0 2.60 270 6.0 3.71 380 7.0 5.03 510 Manila Rope 4 2.35 130 5.0 -- -- 6.0 5.28 280 7.0 -- -- 81
Surge Arrestors Broadband Propagation offers a range of high quality surge arrestors available at a very economical price. Our surge arrestors protect your expensive transmitting and receiving equipment from static discharge and lightning pulses. Our range of surge arrestors is available with different types of connectors and frequency ranges from DC to 2.5 GHz and up to 2000 Watt transmitter power. The Body is machined from solid brass with a Nickel plated finish and has high quality connectors. Rugged top quality Surge Arrestors at a very low price SPECIFICATIONS: Code Type Frequency range Description BPSA 230 UHF BNC N DC to 1 GHz DC to 2 GHz DC to 2.5 GHz 230 Volt Arc-over Voltage for use with Transmitters up to 400 Watts BPSA 600 UHF N DC to 1 GHz DC to 2.5 GHZ 600 Volt Arc-over Voltage for use with Transmitter up to 2000 Watts 82
1-3 Adelaide Rd. Echunga Fax:.(08) 8388 8536 PO Box 529 Echunga Intl.Phone:.(618) 8388 8132 ABN: 47 143 178 438 LIGHTNING ARRESTOR KITS Broadband Propagation's Lightning Arrestor Kits offer accessories to accompany our 'coaxial surge arrestor' range. They enable you to install a complete static discharge/ lightning protection system for your antenna. KIT CONTAINS Earthing Kit: (BPEK) Earth Lead: (ELS3) 2 part copper earth stake (total length is 1.4m) Brass earth stake joiner Stainless steel dolly Clamp (with fasteners) Length of 3m nickel plated copper braid Feeder Cable Options SA 230 FC: SA 600 FC: SA 600 NFC: 5m of RG58 coaxial cable with BNC connectors 5m of RG 213 coaxial cable with UHF connectors 5m of RG 213 coaxial cable with N type connectors Earth leads and feeder cables can be supplied at longer lengths if required. Please specify when ordering. Surge Arrestor Options Code Type Frequency range Description BPSA 230 UHF BNC N DC to 1 GHz DC to 2 GHz DC to 2.5 GHz 230 Volt Arc-over Voltage for use with Transmitters up to 400 Watts BPSA 600 UHF N DC to 1 GHz DC to 2.5 GHZ 600 Volt Arc-over Voltage for use with Transmitter up to 2000 Watts * All components of our lightning arrestor kits can be sold separately if required. 83
EARTHING OPTIONS The body of the lightning arrestor must be adequately earthed to perform its job. This can be achieved by bolting the body of the arrestor directly to a well earthed object such as an earth stake, or it can be earthed indirectly through an earthing cable. 84