CYINDRICA TYPE PHOTOEECTRIC SENSORS UZC Series SIMPE MOUNTING WITH A M8 THREAD M8 Thread This sensor has a M8 thread on an enclosure, which is convenient for mounting. Easy to Replace The sensor with a connector (UZC---A) makes its replacement easy. ong Sensing Range Thru-beam m 9.7ft. Retroreflective m 9.8ft. (With Polarizing filters :.5m.9ft.) M8.79 Diffuse reflective mm.7inch Wide Product Range Supply voltage q AC type ( to V AC) w DC type ( to V DC) Output q NPN open-collector w PNP open-collector e AC non-contact (thyristor) output Connection q Cable type w Connector type A total of models are available. Environment Resistant IP67 achieved by total encapsulation. Strong resistance against vibration by resin encapsulation. Connector protection is also IP67. Convenient Options Side-view attachment (For the thru-beam sensors only) ight is bent to a right angle when this attachment is used. Slit mask (For the thru-beam sensors only) It is convenient for detecting small objects or enhancing sensing accuracy. 5
APPICATIONS Cardboard boxes sensing Specular objects sensing Milk packs sensing ORDER GUIDE Appearance (*) Sensing range Model No. Supply voltage Output Output operation Thru-beam m 9.7ft. UZC UZC5 NPN open-collector PNP open-collector DC type Retroreflective (*) With polarizing filters m 9.8ft. (*).5m.9ft. (*) UZC UZC5 UZC UZC5 to V DC NPN open-collector PNP open-collector NPN open-collector PNP open-collector ight-on/dark-on Selected by an operation mode control wire Diffuse reflective mm.7inch UZC UZC5 NPN open-collector PNP open-collector Thru-beam m 9.7ft. UZC UZC ight-on Dark-ON AC type Retroreflective (*) With polarizing filters m 9.8ft. (*).5m.9ft. (*) UZC5 UZC5 UZC UZC to V AC ± % AC non-contact (thyristor) output ight-on Dark-ON ight-on Dark-ON Diffuse reflective mm.7inch UZC UZC ight-on Dark-ON Cautions : A reflector is not supplied with the retroreflective sensor. Purchase a reflector separately. (*) : The sensing range of the retroreflective sensor is the figure using a UZZ reflector. 5
ORDER GUIDE Connector Type The sensor with a connector is also available. When ordering this type, add suffix A at the end of the model number. Purchase a mating cable separately. e.g.) The connector type of UZC5 is UZC5A. Mating cable Type Model No. Description For DC type sensors (*) For AC type sensors (*) UZC8 UZC8 UZC8 UZC8 UZC8 UZC8 UZC8 UZC8 ength: m 6.56ft. ength: 5m 6.ft. ength: m 6.56ft. ength: 5m 6.ft. ength: m 6.56ft. ength: 5m 6.ft. ength: m 6.56ft. ength: 5m 6.ft. For the emitter of the thru-beam sensor ( cores) (*) For the emitter/receiver of the thru-beam, retroreflective and diffuse reflective sensors ( cores) (*) For the emitter of the thru-beam sensor ( cores) The receiver of the thru-beam, retroreflective and diffuse reflective sensors ( cores) (*) : Mating cables for the DC and AC type sensors are not compatible with each other as connector dimensions are different. (*) : When using an input emission disable, use UZC8 of cores. OPTION Component Model No. Description Side-view attachment Slit mask (For thru-beam sensor only) Side-view attachment (For thru-beam sensor only) (For retroreflective sensor only) mounting bracket UZC8 UZC8 UZZ UZZ UZZ UZZ UZZ.6.5mm.57.inch.6.5mm.57.59inch.6mm.57.8inch ight is bent to a right angle with this attachment. Sensing range (when fitted to both side) : 8m 6.7ft. Sensing range: m 9.8ft. [UZC & UZC5],.5m.9ft. [UZD & UZD] Sensing range: m 6.56ft. [UZC & UZC5],.m.97ft. [UZD & UZD] Sensing range: m.8ft. [UZC & UZC5],.7m.97ft. [UZD & UZD] Protective mounting bracket for UZZ Protects the reflector from damage and keeps an exact alignment. For UZZ the emitter the receiver both sides the emitter the receiver both sides the emitter the receiver both sides Sensing range: m 9.8ft. Min. sensing object: φ8mm φinch Sensing range:.5m 8.ft. Min. sensing object: φ8mm φinch Sensing range:.8m.6ft. Min. sensing object:.7mm.9.8inch Sensing range: 5m 6.ft. Min. sensing object: φ8mm φinch Sensing range:.5m.76ft. Min. sensing object: φ8mm φinch Sensing range: m 6.56ft. Min. sensing object: mm.9.79inch Sensing range: 7.5m.66ft. Min. sensing object: φ8mm φinch Sensing range: 7m.966ft. Min. sensing object: φ8mm φinch Sensing range:.5m.76ft. Min. sensing object: mm.9.8inch Slit mask UZZ.8.5 UZZ 5..9..665 Reflective tape UZZ.98...8. 8. 59..7.5.7.8 UZZ UZZ 8 5..98.8 mounting bracket UZZ UZZ 8..9.7.8 UZZ For UZZ Reflective tape (For retroreflective sensor only) UZZ UZZ Sensing range:.7m.97ft. [UZC & UZC5],.m.ft. [UZD & UZD] Sensing range:.5m.6ft. [UZC & UZC5] pieces of Mmm.9inch cross-recessed bolts are supplied. pieces of M8mm inch cross-recessed bolts are supplied. UZZ pieces of Mmm.7inch cross-recessed bolts are supplied. 5
SPECIFICATIONS DC type sensors Data Sensing mode Thru-beam Retroreflective (*) With polarizing filters Diffuse reflective Model No. NPN Output PNP Output UZC UZC5 UZC UZC5 UZC UZC5 UZC UZC5 Sensing range m 9.7ft. m 9.8ft. (*).5m.9ft. (*) mm.7inch (*) Sensing object Opaque object of min. φ8mm φinch Opaque & translucent objects Opaque, translucent & specular of min. φ5mm φ.969inch (*) objects of min. φ5mm φ.969inch (*) Opaque, translucent & transparent objects Hysteresis Repeatability (vertical direction for a light axis) Supply voltage.mm.inch or less to V DC Ripple P-P : ±% or less 5% or less of an operation range.mm.inch or less Consumption Output Emitter: ma or less Receiver: ma or less <NPN output type> NPN open-collector Current sink: Max. ma Applied voltage: V DC or less Residual voltage:.5v DC or less (at ma current sink) ma or less <PNP output type> PNP open-collector Current source: Max. ma Applied voltage: V DC or less Residual voltage:.5v DC or less(at ma current source) Output operation Short-circuit protection Response time Selection of ight-on/dark-on by a control input wire Equipped ms or less Emission disable function Emission indicator Protection Equipped Red ED (turns on when the output is in the ON state) Thru-beam sensor is provided to the receiver. Red ED (turns on at the emitting) Equipped with the emitter IP67 (IEC) Ambient temperature to + 55 C to + F (with no dew nor ice condensation), Storage: to + 7 C to + 58 F Environmental resistance Ambient humidity Ambient light Noise Dielectric Insulation Vibration Shock 5 to 85%RH, Storage: 5 to 85%RH Sun light:, at the light-receiving face, Incandescent light:,5 at the light-receiving face Power line: Vp with.5µs pulse duration Radiation: Vp with.5µs pulse duration (by a noise simulator),v AC applied between the live parts and enclosure for min. Min. MΩ applied between the live parts and enclosure at V DC.5mm.59inch {Max. G} amplitude at the frequency of to 5Hz in each of X, Y and Z directions for hours each in the power OFF state 5m/s {approx. 5G} impulse in each of X, Y and Z directions for times each in the power OFF state Emitting element Infrared ED (modulated) Red ED (modulated) Infrared ED (modulated) Material Cable Cable extension Enclosure: PBT (gray), ens: Polycarbonate Enclosure: PBT (gray), Font cover: Acrylic.mm cores with m 6.56ft. of cabtyre cable ( cores for the emitter only) Extensible up to m 8.8ft. by using..mm or more cable (Thru-beam sensor: each of an emitter and a receiver) Weight Emitter: Approx. 9g.75oz Receiver: Approx. g.57oz Approx. g.57oz Accessories Nut: pcs. Nut: pcs. (*): A reflector is not supplied with the retroreflective sensor. Purchase a reflector separately. (*): The sensing range and sensing object of the retroreflective sensor is the figure using a UZZ reflector (optional). (*): The sensing range of the difuse reflective sensor is the figure using an object of non-glossy white paper (mm 7.877.87inch). 5
SPECIFICATIONS AC type sensors Data Sensing mode Thru-beam Retroreflective (*) With polarizing filters Diffuse reflective Model No. ight-on Dark-ON UZC UZC UZC5 UZC5 UZC UZC UZC UZC Sensing range m 9.7ft. m 9.8ft. (*).5m.9ft. (*) mm.7inch (*) Sensing object Opaque object of min. φ8mm φinch Opaque & translucent objects Opaque, translucent & specular of min. φ5mm φ.969inch (*) objects of min. φ5mm φ.969inch (*) Opaque, translucent & transparent objects Hysteresis 5% or less of an operation range Repeatability (vertical direction for a light axis).mm.inch or less.mm.inch or less Supply voltage to V AC ±% Consumption Output Response time Emitter:.5VA or less Receiver:.5VA or less.7va or less AC non-contact (thyristor output) oad current: 5 toma Applied voltage: to V AC ± % Residual voltage: Max. V AC (at ma load current) ms or less Power indicator Protection Red ED (turns on when the output is in the ON state) Thru-beam sensor is provided to the receiver ( ) Red ED turns on when the power is supplied Equipped with the emitter IP67 (IEC) Ambient temperature to + 55 C to + F (with no dew nor ice condensation), Storage: to + 7 C to + 58 F Environmental resistance Ambient humidity Ambient light Noise Dielectric Insulation Vibration Shock 5 to 85%RH, Storage: 5 to 85%RH Sun light:, at the light-receiving face, Incandescent light:,5 at the light-receiving face Power line:,5vp with.5µs pulse duration Radiation: Vp with.5µs pulse duration (by a noise simulator),5v AC applied between the live parts and enclosure for min. Min. MΩ applied between the live parts and enclosure at 5V DC.5mm.59inch {Max. G} amplitude at the frequency of to 5Hz in each of X, Y and Z directions for hours each in the power OFF state 5m/s {approx. 5G} impulse in each of X, Y and Z directions for times each in the power OFF state Emitting element Infrared ED (modulated) Red ED (modulated) Infrared ED (modulated) Material Cable Cable extension Enclosure: PBT (gray), ens: Polycarbonate Enclosure: PBT (gray), Font cover: Acrylic.mm cores with m 6.56ft. of cabtyre cable ( cores for the emitter only) Extensible up to m 8.8ft. by using..mm or more cable (Thru-beam sensor: each of an emitter and a receiver) Weight Emitter: Approx. 9g.75oz Receiver: Approx. g.57oz Approx. g.57oz Accessories Nut: pcs. Nut: pcs. (*): A reflector is not supplied for the retroreflective sensor. Purchase a reflector separately. (*): The sensing range and sensing object of the retroreflective sensor is the figure using a UZZ reflector (optional). (*): The sensing range of the diffuse reflective sensor is the figure using an object of non-glossy white paper (mm 7.877.87inch). 55
TYPICA WIRING DIAGRAMS NPN output type Wire color/connector pin No. Brown circuit D ZD Tr (Brown/)V oad (Black/) Output (*) MAX. ma (Violet/) * Emission disable input (*) (Pink/) Control input (*) (Blue/) V to V DC Black Violet (*) Pink (*) * oad to V DC Internal circuit Users circuit Blue (*): Output and control input are not equipped for the emitter of the thru-beam sensor. Wire color of the control input is white in case of the mating cable for the connector type sensor. (*): Emission disable input is equipped for the emitter of the thrubeam sensor only. Wire color of mating cable for the connector type sensor is white. Symbol...D : Reverse polarity protection diode ZD : Surge absorption zener diode Tr : NPN output Connection Diagram of Connector Pin * Non-voltage contact or NPN open-collector OR : V : Emission disable input or control input : V : Output or not used Emission disable input ow ( to.5v): Emission disable High (6 to V or open): Emission Control input ow ( to.5v): Dark-ON High (6 to V or open): ight-on PNP output type Wire color/connector pin No. Brown circuit D ZD Internal circuit (Brown/)V Tr (Black/) Output (*) (Violet/) Emission disable input (*) (Pink/) Control input (*) (Blue/) V Users circuit * MAX. ma oad to V DC Black * Violet (*) Pink (*) Blue oad to V DC (*): Output and control input are not equipped for the emitter of the thru-beam sensor. Wire color of the control input is white in case of the mating cable for the connector type sensor. (*): Emission disable input is equipped for the emitter of the thrubeam sensor only. Wire color of mating cable for the connector type sensor is white. Symbol...D : Reverse polarity protection diode ZD : Surge absorption zener diode Tr : PNP output Connection Diagram of Connector Pin * Non-voltage contact or PNP open-collector OR : V : Emission disable input or control input : V : Output or not used Input for emission disable ow ( to.5v or open): Emission High ( to V): Emission disable Control input ow [Max. (supply voltage 6V) or open]: igh-on High [Min. (supply voltage.5v)]: Dark-ON 56
TYPICA WIRING DIAGRAMS AC non-contact output type Emitter of thru-beam sensor Emitter of thru-beam sensor Brown Wire color/connector pin No. (Brown/) AC IN to V AC % circuit Internal circuit (Blue/) AC IN Users circuit to V AC % Blue Connection Diagram of Connector Pin : AC IN : Not used : AC IN : Not used Receiver of thru-beam, retroreflective & diffuse reflective sensor Receiver of thru-beam, retroreflective & diffuse reflective sensor Brown Wire color/connector pin No. (Brown/) AC IN Black oad to V AC % circuit Internal circuit (Black/) Output (Blue/) AC IN Users circuit oad to V AC % Blue Connection Diagram of Connector Pin : AC IN : Not used : AC IN : Output SENSING FIEDS These are typical sensing fields, which may vary slightly from unit to unit. UZC UZC Thru-beam UZC UZC5 Retroreflective Parallel Angular Parallel Angular.. Setting distance (m ft.).88 5 6. Receiver Emitter Setting distance (m ft.).88 5 6. Emitter θ Receiver Setting distance (m ft.) 9.8 6.56.8 (UZZ) Setting distance (m ft.) 9.8 6.56.8 (UZZ) θ (UZZ) θ 5.78 7.87 7.87 eft Center Right Deviation (mm inch) 5.78 eft Center Angle θ ( ) Right.97 5.969 5.969 eft Center Right Deviation (mm inch).97 eft Center Angle θ ( ) Right UZC UZC Retroreflective UZC UZC Parallel Angular Sensing field Setting distance (m ft.) 6.56.5.9.8.5.6 (UZZ) Setting distance (m ft.) 6.56.5.9.8.5.6 (UZZ) θ (UZZ) θ Setting distance (mm inch) 7.87 5 5.96.97 5.969 mm 7.877.87inch Non-glossy white paper Diffuse reflective.97 5.969 5.969 eft Center Right Deviation (mm inch).97 eft Center Right Angle θ ( ).787.9.9 eft Center Right Deviation (mm inch).787 57
PRECAUTIONS FOR PROPER USE These products are not safety sensors and are not designed or intended to be used to protect life and prevent bodily injury or property damage. Mounting Tightening torque must not exceed N m{.kgf cm}. Setting of UZC and UZC5 When detecting a glossy object, mount the sensor at an angle of to against the surface on the object. Glossy surface Sensing object to Distance should be as long as possible. Others Do not use the sensor output signal for 5ms immediately after the power is supplied to the sensor. DIMENSIONS (Unit: mm inch) UZC, UZC UZC UZCA, UZCA UZCA φ. φ.99.8..8 φ.9 φ.587 56.5.575 8 φ6.8 φ.66 (red)(*) φ 5 cable φ.97, 78.7 (5) (.969) (8) () φ. φ.99.8..8 φ.9 φ.587 56.5.575 8 φ6.8 φ.66 (red) φ 5 cable φ.97 () (7.87) () (.7) φ φ.55 M connector (*): It is the emitting indicator (red) for the emitter of the thru-beam sensor. (*): It is the emitting indicator (red) for the emitter of the thru-beam sensor. φ. φ.99 UZC.8.5..77 φ.9 φ.587 57.5.6.575 8 φ6.8 φ.66 φ5 cable φ.97, 78.7 (5) (.969) (8) () φ. φ.99 UZCA.8.5..77 φ.9 φ.587 57.5.6.575 8 φ6.8 φ.66 φ 5 cable φ.97 () (7.87) () (.7) φ φ.55 M connector UZC, UZC5 UZC φ. φ.99.8..8 7.795 55.65 8 φ.9 φ 6.8 φ.66 φ.587 (red)(*), 78.7 φ 5 cable φ.97 (5) (.969) (8) () φ. φ.99 UZCA, UZC5A UZCA.8..8 7.795 55.65 8 φ.9 φ 6.8 φ.66 φ.587 (red)(*) () (7.87) () (.7) φ φ.55 φ5 cable φ.97 M connector (*): It is the power indicator (red) for the emitter of the thru-beam sensor. (*): It is the power indicator (red) for the emitter of the thru-beam sensor. UZC UZCA φ. φ.99.8.5..77 7.5.85 55.65 8 φ.9 φ 6.8 φ.66 φ.587, 78.7 φ5 cable φ.97 (5) (.969) (8) () φ. φ.99.8.5..77 7.5.85 55.65 8 φ.9 φ 6.8 φ.66 φ.587 () (7.87) () (.7) φ φ.55 φ5 cable φ.97 M connector 58
DIMENSIONS (Unit: mm inch) UZZ (option) UZZ (option).8.5.. 5..9...6.98.9 M nut mounting-hole (mounting on the back) Base - φ. φ. mounting hole (mounting on the side) - φ. φ. mounting hole depth 6.6 (mounting on the back)...5.665 8.98 () (.87) - φ.6 φ. Mounting hole 8..7.. Material : Acrylic (reflector) ABS (base) pieces of M8mm inch cross-recessed bolts and pieces of nuts are supplied. M nut mounting-hole (mounting on the side) Material : Acrylic (reflector) ABS (base) UZZ (option) UZZ Reflective tape (option) 5..98.8 (8) (.).7.8 9..9 59..5 8 (6) (.6) () (.8) Effective reflecting surface Adhesive tape.9.575 5.97 - φ.6 φ.8 Mounting hole 8..7.. Material : Vinyl chloride Material : Acrylic (reflector) ABS (base) UZZ Reflective tape (option).8 (8) (.).7.8.98 () (.96) Effective reflecting surface Adhesive tape Material : Vinyl chloride 59
DIMENSIONS (Unit: mm inch) UZZ Mounting bracket for UZZ reflector (option) 5.5.7.96 φ 6 5 φ.7.969 Mounting drawing 5.5.7.96 φ 6 5 φ.7.969.9..6 6.6.5.8.9.5 Material : SUS pieces of Mmm.7inch cross-recessed bolts are supplied. t..7 φ φ.98.5.9 R7.5.95 6.8.98 6.8.98.8.5.5 UZZ Mounting bracket for UZZ reflector (option).98 5.78.98.5.77.9. Mounting drawing.5.77.98.9 8. 9.. 8..76.7 6.6.9 8 6.6.7 8-MP.5 thru-hole.787 t.6.6..7 (7) (.57) 5..9..5 () (.87) 8 t.6.6 Material : SPCC pieces of M8mm inch cross-recessed bolts are supplied. 6.6 UZZ Mounting bracket for UZZ reflector (option) () (.8).575 5.969.575.5.77.9 5.97 6.6. Mounting drawing.5.77.9.575 5..98 8..7 8. 9...76 5.78 5.59 6..7 () (.8) 6. (8) (.) Material : SPCC pieces of Mmm.9inch cross-recessed bolts are supplied. 8.79 7.76 8-MP.7 thru-hole.787 t.79 6.. () (.6) 7.76.575 () (.8) 5.97 9..9.9 t.79 6