INSTALLATION, ASSEMBLY & OPERATIONAL MANUAL

Dog Park Equipment Hill Climb, Balance Beam, Bridge Climb, Mini Hill Climb, Jump Hurdles, Tunnel House, Training Platform, Jump Balance Beam Safe Zone When installing equipment on grass, place 4 of, Cedar Wood Mulch or Crushed Granite Trail Mix as a surrounding surface for the play equipment. It is recommended a safe zone on the sides and front and back of products. This provides a cushion area for the dogs to play safely. DOG PARK PRODUCTS PLACEMENT AND USAGE Try to keep the center of the park open for an area where dogs can run and chase balls and play. Do not let your dog use the play equipment or climbing, walking equipment during inclement weather periods - rainy weather, cold days with ice or snow and hot days above 70 degrees. Please inspect the walking surfaces prior to using the play equipment. It is recommended that you inspect the area for freshness. Some areas may require refreshing and replacing that may be dirty. Keep the safe zone areas clean. We recommend 4 of around the equipment. If the equipment is placed on concrete, we recommend using our Dura Dog Soft Cushion Jumping Mats (below). It is important to provide adequate drinking water and a cooling source for dogs as they can overheat during summer months. It is recommended a water fountain be supplied at a close proximity to the play area. During the summer months it is recommended to have a cooling source for the dogs to keep cool during play times in hot periods (above 70 degrees). During extreme weather conditions (icy weather, rainy weather, hot weather) it may be advisable to close the park to protect pets from extreme weather conditions. Some parks may opt to store equipment during icy or cold winter seasons. Inspect equipment and surrounding areas regular to ensure safe play for both pets and owners. RECOMMENDED PRODUCT FOR INDOOR CONCRETE SURFACES INSTALLATION NOTE - Equipment is heavy and is recommended that two people lift. TOOLS NEEDED (PORTABLE AND IN-GROUND) Socket set and wrenches Drill with 1/2 and/or 5/8 drill bit Rake to spread INSTALLATION OPTIONS Portable and free-standing - products can be placed on nearly any type of surface. Make sure products are on level ground and feet are flat. In-ground and earth mounting - use landscape spikes. Holes need to be drilled in feet. Spikes sold separately. In-ground concrete footer mounting - Holes need to be drilled in feet. Concrete and anchor bolts sold separately. AGILITY PRODUCTS TOOLS NEEDED FOR IN-GROUND MOUNT Shovel or post hole digger Concrete, Quikcrete or similar Wheel Barrel Water hose or bucket of water FOR PROFESSIONAL FINISH INSTALL Small paint brush Black frame trim finishing of cut boards and exposed nuts and bolts POLY WOOD - use flat black oil-based enamel paint NATURAL WOOD - ONLY use flat black acrylic paint Finishing of bolts Touch bolts with black paint or stain after each install Note - Jump Hurdles are designed to be free standing so they can tip if a dog misses a jump. This is for the safety of the dog and should be installed as free standing and portable. DURA DOG SOFT CUSHION JUMPING MATS DL-DJM150-SOFT 1/2 Thickness DL-DJM916-SOFT 9/16 Thickness Soft. though. durable. Provide a cushioned soft landing pad on hard surfaces with our Dura Dog Soft Cushion Jumping Mats. Placing these mats next to equipment gives dogs a safer landing zone and protects them from injury. Sold in rolls or individual pads for indoor application. These mats are meant to be placed in front of ramps and other jump zone areas. JUMP HURDLES BRIDGE CLIMB MINI HILL CLIMB TUNNEL HOUSE HILL CLIMB TRAINING PLATFORM JUMP BALANCE BEAM 2 3

BRIDGE CLIMB (S/M) Anchoring instructions Fastener, 3/8 x 5 min. wedge anchor. Fastener should be a minimum of 1inch form edge of board. Recommend to cut excess threads of anchor off for safety. Assembly Notes Step 1: Assemble - Bolt (#6), washer (#7), nut (#8), nut (#9) and Item 1 (platform) to Item 2 (legs). Step 2: Assemble - Bolt (#5), washer (#7), nut (#8), nut and Item 3 (ramps) to platform and leg assembly. Step 3: Place on level surface and check product with a level - check all connections. BRIDGE CLIMB (S/M) PATENT PENDING All Rights Reserved Gyms For Dogs 800-931-1562 Phone www.gymsfordogs.com For professional touch, paint bolts with black paint or stain after each install 33 bags of cedar or cypress Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. 4 DRW. NO. 81-011-10009 5

BRIDGE CLIMB (L/XL) Anchoring instructions Fastener, 3/8 x 5 min. wedge anchor. Fastener should be a minimum of 1inch form edge of board. Recommend to cut excess threads of anchor off for safety. Assembly Notes Step 1: Assemble - Bolt (#4), washer (#5), nut (#6), nut (#7) and Item 2 (platform) to Item 3 (legs). Step 2: Assemble - Bolt (#8), washer (#5), nut (#6), nut (#7) and Item 1(ramps) to platform and leg assembly. Step 3: Place on level surface and check product with a level - check all connections. BRIDGE CLIMB (L/XL) PATENT PENDING All Rights Reserved Gyms For Dogs 800-931-1562 Phone www.gymsfordogs.com 33 bags of cedar or cypress For professional touch, paint bolts with black paint or stain after each install Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. 6 DRW. NO. 81-011-10001 7

MINI HILL CLIMB Anchoring instructions Fastener, 3/8 x 5 min. wedge anchor. Fastener should be a minimum of 1inch form edge of board. Recommend to cut excess threads of anchor off for safety. Assembly Notes Step 1: Assemble - Bolt (#5), washer (#7), nut (#8) and Item 1 (ramps). Step 2: Assemble - Bolt (#6), washer (#7), nut (#8) and Item 2 (gussets) to ramp assembly. Gusset supports go underneath. Step 3: Place on level surface and check product with a level - check all connections. MINI HILL CLIMB PATENT PENDING All Rights Reserved Gyms For Dogs 800-931-1562 Phone www.gymsfordogs.com 10 bags of cedar or cypress Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. Place underneath. 6 DRW. NO. 81-011-10004 7

HILL CLIMB Anchoring instructions Fastener, 3/8 x 5 min. wedge anchor. Fastener should be a minimum of 1inch form edge of board. Recommend to cut excess threads of anchor off for safety. Assembly Notes Step 1: Assemble - Bolt (#3), washer (#4), nut (#5), nut (#6) and Item 1. Step 2: Assemble - Bolt (#7), washer (#4), nut (#5), nut (#6) and Item 2 (gussets) to ramp assembly. Gusset supports go underneath. Step 3: Place on level surface and check product with a level - check all connections. HILL CLIMB PATENT PENDING All Rights Reserved Gyms For Dogs 800-931-1562 Phone www.gymsfordogs.com 16 bags of cedar or cypress Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. Place underneath. 8 DRW. NO. 81-011-10000 9

TRAINING PLATFORM Anchoring instructions Fastener, 3/8 x 5 min. wedge anchor. TRAINING PLATFORM PATENT PENDING All Rights Reserved Gyms For Dogs 800-931-1562 Phone www.gymsfordogs.com Fastener should be a minimum of 1inch form edge of board. Recommend to cut excess threads of anchor off for safety. Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. 24.00 24.00 24.00 For professional touch, paint bolts with black paint or stain after each install 24.00 8 bags of cedar or cypress 6 DRW. NO. 81-011-10002 7

Safe Zone - Provide cypress or cedar under and around the Tunnel House to provide a soft area for dogs to lay down and play in. If placed on artificial turf it is completely optional for any surfacing at all. TUNNEL HOUSE Anchoring instructions Fastener, 3/8 x 5 min. wedge anchor. Fastener should be a minimum of 1inch form edge of board. Recommend to cut excess threads of anchor off for safety. Assembly Note Step 1: Assemble - Bolt (#7), washer (#8), nut (#11) and Item 2 (roof. Step 2: Assemble - Bolt (#6), washer (#8), nut (#11) and Item 3( gussets) to roof assembly. Gusset supports go underneath. Step 3: Assemble - bolt (#10), washer (#8), nut (#11), nut (#12) and Item 12 (legs). Step 4: Place on level surface and check product with a level - check all connections. TUNNEL HOUSE PATENT PENDING All Rights Reserved Gyms For Dogs 800-931-1562 Phone www.gymsfordogs.com For professional touch, paint bolts with black paint or stain after each install 12 bags of cedar or cypress Place underneath. 8 DRW. NO. 81-011-10006 9

JUMP HURDLE LARGE JUMP HURDLE LARGE Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. 72.00 72.00 For professional touch, paint bolts with black paint or stain after each install 10.5 bags of cedar or cypress For professional touch on Poly Wood equipment, we recommend coating designated areas with a non-oil based acrylic black flat enamel. For Natural Wood equipment, use Behr Premium Solid Stain Sealer in Ebony finish. 10 DRW. NO. 81-011-10008 11

JUMP HURDLE MEDIUM JUMP HURDLE MEDIUM For professional touch, paint bolts with black paint or stain after each install Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. 72.00 72.00 10.5 bags of cedar or cypress For professional touch on Poly Wood equipment, we recommend coating designated areas with a non-oil based acrylic black flat enamel. For Natural Wood equipment, use Behr Premium Solid Stain Sealer in Ebony finish. 12 DRW. NO. 81-011-10007 13

JUMP HURDLE SMALL JUMP HURDLE SMALL Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. 72.00 72.00 For professional touch, paint bolts with black paint or stain after each install 10.5 bags of cedar or cypress For professional touch on Poly Wood equipment, we recommend coating designated areas with a non-oil based acrylic black flat enamel. For Natural Wood equipment, use Behr Premium Solid Stain Sealer in Ebony finish. 14 DRW. NO. 81-011-10005 15

JUMP BALANCE BEAM JUMP BALANCE BEAM For professional touch, paint bolts with black paint or stain after each install Safe Landing Zone: Provide a 4 absorption layer of cypress or cedar or some form of absorption in the defined landing zone (see above) around the equipment to provide a safe landing zone. For concrete floor installations we recommend using our Dura Dog Soft Cushion Jumping Mats in front of each ramp. 14 bags of cedar or cypress For professional touch on Poly Wood equipment, we recommend coating designated areas with a non-oil based acrylic black flat enamel. For Natural Wood equipment, use Behr Premium Solid Stain Sealer in Ebony finish. 16 DRW. NO. 81-011-10003 17

TRAIL BENCH WITH BACK IN-GROUND MOUNT (SHOWN) and SURFACE MOUNT NATURAL PARK BENCH BENCHES TRAIL BENCH IN-GROUND MOUNT and SURFACE MOUNT (SHOWN) NATURAL PARK BENCH WITH BACK ASSEMBLY AND MOUNTING INSTRUCTIONS TRAIL BENCH WITH BACK 1. Set up two support frame weldments on a smooth, level surface roughly 62 inches apart on centers laying them on their back with seat in a vertical direction. Center the third weldment between them. See diagram 1. 2. Mark each plate at a distance of 2 7/8, 7, and 11 1/4 inches from the end of the plate. Diagram 2. 3. Locate bull nose board on the weldment at a distance of 3 1/4 inches from end of the board to edge of weldment plate and flat edge on the 11 1/4 inch mark. Make certain curved edge is facing bend in plate. 4. Clamp board to weldment and locate the second weldment at distance of 34 1/4 inches from end of board and the board flat edge on the 11 1/4 inch mark. Clamp board to weldment. Diagram 2. 5. Locate the third weldment at distance of 65 1/4 inches from end of board and the board flat edge on the 11 1/4 inch mark. Clamp weldment to board. See diagram 2. 6. Drill 5/32 diameter pilot hole (six places) into the board and install six Â¼ x 2 screws into the board (use fourth line of 2 holes in metal plate of weldments as a drill guide). 7. Set one rectangular board at a distance of 3 1/4 inches from plate side edge to end of board with flat edge on the 7 inch marks. Place a 3/4 inch thick spacer between the bull nose and rectangular board at each end to maintain 3/4 inch gap. Clamp board in place. See diagram 2. 8. Drill 5/32 diameter pilot hole (six places) into the board and install six Â¼ x 2 screws into the board (use third line of 2 holes in metal plate of weldment as a drill guide). 9. Set the second rectangular board at a distance of 3 1/4 inches from plate side edge to end of board with flat edge of board on 2 7/8 inch mark. Place a 3/4 inch thick spacer between the two rectangular boards at each end to maintain 3/4 inch gap. See diagram 2. 10. Drill 5/32 diameter pilot hole (six places) into the board and install six Â¼ x 2 screws through washers into the board (use second line of 2 holes in metal plate of weldments as a drill guide). 11. Locate second bull nose board at a distance of 3 1/4 inches from plate side edge to end of board and at a gap distance of 3/4 inch between bull nose and rectangular board. Place a 3/4 inch thick spacer between the bull nose and rectangular board at each end to maintain 3/4 inch gap. See diagram 2. 12. Drill 5/32 diameter pilot hole (six places) into the board and install six Â¼ x 2 screws through washers into the board (use first line of 2 holes in metal plate of weldments as a drill guide). 13. Check squareness of boards with plates with hand square before tightening screws. 14. Set the bench upright to fasten the boards on the back. See diagram 3. 15. Mark each plate at a distance of 2 7/8, 71/8 inches from the end of the plate. Diagram 2 16. Locate one bull nose board on the weldments at a distance of 3 1/4 inches from end of the board to edge of weldment plate with flat edge of board on the 7 1/8 inch marks. Make certain curved edge is facing bend in plate. Clamp board in place. See diagram 3. IMPORTANT: Make sure that the distance between the two bull nose boards where seat meets the back measures 4 inches or less. Adjust the board on the back to meet 4 inch maximum dimension. 17. Drill 5/32 diameter pilot hole (six places) into the board and install six Â¼ x 2 screws into the board (use third line of 2 holes in metal plate of weldments as a drill guide). Diagram 3. 18. Set one rectangular board at a distance of 3 1/4 inches from plate side edge to end of board with flat edge of board on the 2 7/8 inch mark. Clamp board in place. Place a 3/4 inch thick spacer between the bull nose and rectangular board at each end to maintain 3/4 inch gap. See diagram 3. 19. Drill 5/32 diameter pilot hole (six places) into the board and install six Â¼ x 2 screws into the board (use second line of 2 holes in metal plate of weldments as a drill guide). Diagram 3. 20. Locate second bull nose board at a distance of 3 1/4 inches from plate side edge to end of board with a gap distance of 3/4 inches between bull nose and rectangular boards at both ends. Place a 3/4 inch thick spacer between the bull nose and rectangular board at each end to maintain 3/4 inch gap. Clamp board in place. See diagram3. 21. Drill 5/32 diameter pilot hole (four places) into the board and install four Â¼ x 2 screws into the board (use first line of 2 holes in metal plate of weldments as a drill guide). Diagram 3. 22. Check squareness of boards with plates before tightening all screws. 18 19

DIAGRAM 4: SHOWN ARE SURFACE CONCRETE ANCHORS 4 PLACES EMBEDDED HOLES 2 PLACES PORTABLE NO MOUNTING 1. Surface mount bench with ½ inch anchors into concrete surface at dimensions as shown on diagram 3. 2. Embedded mount bench by setting in filled holes at dimensions as shown on diagram 3. 3. Portable bench will rest on any flat, even surface - no mounting required. 20 21

ASSEMBLY AND MOUNTING INSTRUCTIONS TRAIL BENCH 1. Place two bull nose boards on ground with curved side facing away from each other. Place two rectangular boards between the two bull nose boards. Begin with one bull nose board and use other boards as working shims. 2. Place one weldment with 8 drilled holes on plate against boards and locate plate at a distance of 8 1/4 inches from plate side edge to end of bull nose and at a distance of 2 1/8 inches from plate end edge to flat side of bull nose. Use a hand square to line up plate on the bull nose surface. See diagram 1. 3. Drill 5/32 diameter pilot hole (two places) into the board and install two ¼ x 2 screws into the board (use end 2 holes in metal plate of weldment as a drill guide). 4. Place the second weldment with 8 drilled holes in plate against the board and locate a distance of 34 1/4 inches from plate side edge to same end of bull nose used in step 4 and at a distance of 2 1/8 inches from plate end edge to flat side of bull nose. See diagram 1. 5. Drill 5/32 diameter pilot hole (two places) into the board and install two ¼ x 2 screws into the board (use end 2 holes in metal plate of weldment as a drill guide). 6. Place the third weldment with 8 drilled holes in plate against the board and locate a distance of 60 1/4 inches from plate side edge to same end of bull nose used in step 4 and at a distance of 2 1/8 inches from plate end edge to flat side of bull nose. See diagram 1. 7. Locate one rectangular board at a distance of 8 1/4 inches from plate side edge to end of board and at a distance of 7 1/2 inches from extreme curved side of secured bull nose at both ends of rect. board (Ref. ½ inch gap between sides of boards at each end). See diagram 1. 8. Drill 5/32 diameter pilot hole (six places) into the board and install six ¼ x 2 screws into the board (use second line of 2 holes in metal plate of weldment as a drill guide). 9. Locate second rectangular board at a distance of 8 1/4 inches from plate side edge to end of board and at a distance of 11 1/2 inches from extreme curved side of secured bull nose at both ends of rectangular board (Ref. ½ inch gap between sides of rectangular boards at each end). 10. Drill 5/32 diameter pilot hole (six places) into the board and install six ¼ x 2 screws into the board (use third line of 2 holes in metal plate of weldment as a drill guide). 11. Locate second bull nose board at a distance of 8 1/4 inches from plate side edge to end of board and at a distance of 15 1/2 inches from extreme curved sides of two bull nose boards at both ends (Ref. ½ inch gap between sides of rectangular boards at each end). 12. Drill 5/32 diameter pilot hole (six places) into the board and install six ¼ x 2 screws into the board (use fourth line of 2 holes in metal plate of weldment as a drill guide). 13. Check squareness of seat before tightening screws. MOUNTING INSTRUCTIONS 1. Portable seat will rest on any flat, even surface -no mounting required. 2. Surface mount seat mounts with ½ inch anchors into concrete surface at dimensions as shown on diagram 2. 3. Embedded mount mounts by setting in filled holes at dimensions as shown on diagram 2. 22 23

ASSEMBLY AND MOUNTING INSTRUCTIONS NATURAL PARK BENCH 1. Begin by setting up seat boards with two rectangular boards in center and one bull nose board on each side with curved section facing out. Set boards on flat work surface with best surface down as this will be the top of the seat. See diagram 1. 2. Use a square to line up all the board ends so they are parallel. Then locate one support casting flat side down on the boards at a distance of 21 3/4 inches from end of the boards to the edge of casting plate. Space the lugs of the support casting between the edges of the boards. Make certain there is a 3/8 inch gap between all boards. 3. Drill 5/32 diameter pilot hole (eight places) into the board and install eight ¼ x 1 screws into the board (use holes in casting as a drill guide). 4. Locate other support casting flat side down on the boards at a distance of 45 3/4 inches from end of the boards to the edge of casting plate. Space the lugs of the support casting between the edges of the boards. Make certain there is a 3/8 inch gap between all boards. 5. Drill 5/32 diameter pilot hole (eight places) into the board and install eight ¼ x 1 screws into the board (use holes in casting as a drill guide). 6. Locate one seat end casting at the ends of the boards, making sure that the spacing lugs of the casting all fit between the board edges. Press casting firmly against board ends to seat the casting. See diagram 2. Use a hand square to line up board on plate. 7. Lay the support tubes onto the center support and gently seat the ends of each tube into the receiving hole on the end casting. See diagram 2. 8. Install two 1/2 x 1 1/2 cap head screws through spacers into the threaded end of the tube and tighten just enough to make sure tubing will stay in receiving hole of casting. See detail A. 9. Locate the other seat end casting at the other ends of the boards, making sure that the spacing lugs of the casting all fit between the board edges. Press casting firmly against board ends to seat the casting. See diagram 2. 10. Install two 1/2 x 1 1/2 cap head screws through spacers into the threaded end of the tube and tighten just enough to make sure tubing will stay in receiving hole of casting. See detail A. 11. Set the seat upright on a flat level surface and tighten the four cap screws securely seating the tubing firmly in the receiving holes of the castings. 12. Mount the seat using 4 concrete anchors at dimensions shown in diagram 3 24 25

ASSEMBLY AND MOUNTING INSTRUCTIONS NATURAL PARK BENCH WITH BACK 1. Loosely assemble bench end castings to back support tube. See diagram 1. 2. Lay one end casting back side down and attach back support tube. Place support tube into the back receiving hole of the casting and fasten with a 1/2 x 1 1/2 cap screw through a plastic spacer, through the casting and into the threaded end of the support tube. See diagram 1. Make sure the cap is snug but do not tighten. 3. Lay the second end casting back side down and attach back support tube following the same procedure as step 3. 4. Place the center support casting(s) at the proper location(s) on the back support tube. Rest support against the tubing. Reference from inside edge of one end casting to inside edge of support casting. 5. 6 foot bench center supports at 21 inches to edge of first support and 45 inches to edge of second support. 6. Place bull nose board (best side facing you) nose down, into the lower pocket of one end casting and then into the lower pocket of the other end casting. Make certain that the support casting(s) behind the board and the radius portion of casting(s) is on the tubing. May have to spread the end castings outward at upper ends in order to get board in between the end casting flanges (loosen the cap screws a little, if needed). See diagram 2. 7. Place boards into one pocket of an end casting and then into the other pocket in the order shown until last board for seat is in place. Keep best side facing out. Keep boards in front of the support casting(s). Make sure that boards center between the lugs on the support casting(s) 8. Install the front support tube between the two end castings seating the tubing in the radius portion of the support casting(s) and fasten with a 1/2 x 1 1/2 cap screw through a plastic spacer, through the casting, and into the threaded ends of the support tube. See diagram 3. 9. Hand snug all cap screws to square up the frame made by the tubing and end castings. 10. Line up the support castings on the back so they are vertical (parallel with end casting) and properly dimensioned. 11. From the back, drill a 5/32 pilot hole approximately 1/2 inch deep and install a 1/4 x 1 screw into the seat boards at each slotted hole in the support casting(s). 12. Set the bench upright to finish the assembly. 13. Place a bull nose board (best side facing out) nose down, into the lower pocket of one end casting and then into the lower pocket of the other end casting. Make certain that the support casting is behind the board. May have to spread the end castings outward at upper ends in order to get board in between the end casting flanges (loosen the cap screws slightly, if needed). See diagram 3. 14. 1Continue to place boards into one pocket of an end casting and then into the other pocket in the order shown until last board for back is in place. Keep best side facing out. Keep boards in front of the support casting(s). Make sure that boards center between the lugs on the support casting(s) 15. Tighten the four cap screws to secure the end castings to the support tubes. Make certain that the alignment between the end castings is plumb when tightening so bench does not rock. 16. From the back side drill a 5/32 pilot hole approximately 1/2 inch deep and install a 1/4 x 1 screw into the back boards at each slotted hole in the support casting(s). 17. The bench is now ready for mounting. Mounting is shown in diagram 4. 26 27

THE DOG GYM - RUN & PLAY Dog Park Play Area Suggested installation for safe play - use the center of the park as an area where dogs can run, chase balls and play. Gyms For Dogs equipment is designed and manufactured for use by dogs only. Products are not intended for human use. 28 29