Date: Customer: Project: Type: Qty: Piix MRC Order Code: PXLDI - - - - - - ID - - - - - - PXLDI Series PXLDI Piix MRC (Micro Reflector Cell) Direct Light Engine B45 50lm/0.9W B40 045lm/ 9.7W B30 803lm/7.4W B20 543lm/4.9W Values calculated from a 4 fixture @ 4000K using 50º (wide) reflector and DIM driver. Indirect Light Engine B35 2 040lm/9.3W B30 2 885lm/7.9W CCT 27 30 2700K 3000K Direct Optics Secondary Optics 20 20 Narrow CL Clear Lens 35 35 Medium HX Hexcell Louver B25 780lm/6.7W 35 3500K 50 50 Wide DF Diffuse Lens B20 629lm/5.3W 40 4000K XX No Secondary Optics TW Tunable White 2 Values calculated from a 4 fixture @ 4000K with ID optics and DIM driver. ID Indirect Shielding ID Indirect Diffuse Optic IB Indirect Batwing Optic Mounting C Cable S Swivel Stem RS Rigid Stem W Wall Mount Nominal Fixture Length 02 2 ft. 03 3 ft. 04 4 ft. 05 5 ft. 06 6 ft. 07 7 ft. 08 8 ft. XX Runs (over 8 ) round up to the nearest foot and replace the xx with the # (i.e. 3=3 nominal) Finish WH White Voltage 20 20 Volt BK Black 277 277 Volt BL Semi-Matte Black SV Silver 347 UNV 20 thru 277 347 Volt 50/60hz capable SP Specify Premium Color Custom colors are available, Please consult factory Driver Fixture Options DIM 3 0-0V (Linear) DCE 2 Lutron Eco- System FS 6 In-line Fuse DIL 3 0-0V (Logarithmic) DC5 3 Lutron 5-Series SS 6 Separate Switching DM 3 DML 3 eldoled eldoled SOLOdrive 0-0V SOLOdrive 0-0V (Linear) (Logarithmic) SR 3,5 Philips Xitanium SR DALI DED 3 eldoled ECOdrive DALI (Logarithmic) DC2 3,4 Lutron 2-Wire 3 See page 6 for full details. 4 20V only. 5 For use with E and P sensors only. 6 See page 7 for full details and restrictions. Sensor Options Emergency Options Configuration Options xe 7,8 Enlighted Replace x with quantity EC 0 Emergency Circuit Wiring IL90 Horizontal 90 Corner xp 7,8 xp2 7,8 Philips Daylight Philips Occ/Vac EM Internal EM Battery Pack IT90 Lit T section xp3 7,8 Philips Occ/Vac/Daylight EMR Remote Micro Inverter IX90 Lit X section xs 7,9 Sensor Switch Daylight xs2 7,9 Sensor Switch Occ/Vac xs3 7,9 Sensor Switch Occ/Vac/ Daylight xsn nlight Enabled 7 See page 8 for full details and restrictions. 8 For use with SR driver only. 9 For use with DM driver only. 0 See page 7 for full details and restrictions See page 9 for full details and restrictions 5YEAR LED WARRANTY ARRA Compliant ADA Compliant Page of 2
3 5 /6 (00mm) 2 /4 (58mm) 2 3 /8 (60mm) Construction: Housing - Continuous, low copper 6063-T6 extruded aluminum profile with aluminum endcaps, available as Individual fixtures (up to 8 ) or Runs. Faceplate - Extruded aluminum profile with laser cut cells for accuracy. Baffles - Injection molded polycarbonate material with a semi-matte Black finish. Reflectors - Precision-designed, injection molded polycarbonate material for accurate distributions and powerful lighting effects. Three different distributions 20º Narrow (20), 35º Medium (35), or 50º Wide (50). Optional Optics - Clear Cover (CL), Hexcell Louver (HX), or Diffuse Lens (DF) snaps in behind the baffle. Optics cannot be combined within the same cell. Indirect Optics Indirect Diffuse Optic (ID) is diffuse lensing sheet that secures in features of the extrusion. Indirect Batwing Optic (IB) is lensing sheet that secures in features of the extrusion. Mounting(s) - 3/64 Aircraft Cable, Ø5/8 Swivel or Rigid Steel Stem, Wall Bracket (see pages 3 through 6 for details). Aircraft cables (C) are adjustable along the length of the fixture, but should not be moved more than 6 from ends to allow for proper support. Standard Luminaire Lengths - All standard luminaires are supplied in nominal lengths to ensure even distribution of optical cells. Runs and Configurations are available in approximately 2' increments (due to MRC size) starting at the nominal 8 fixture length. **Individual luminaires are not joinable in the field. Exact Length Lunimaries - Individual luminaires, Runs, and Configurations are available to meet your project needs. Please consult factory with your requirements. PX Joiner Runs and Configurations are supplied in multiple housings that are joined together in the field using the supplied PX Joiner system. This allows ease of installation (see page 7 for details). Weight - 2.5 lb. Electrical/Performance: LED Light Engine - Brand-name mid-power LEDs create a high efficiency LED light engine able to provide a lumen maintenance of 96% at 25,000 hours and 92% at 60,000 hours @ 25ºC per TM-2 reports. Reported L70 greater than 60,000 hours. Delivered Lumens - Due to the LED manufacturer s tolerances, the listed output has a ±5% tolerance. For outputs based on different optics or CCT, please see photometry section at the end. CCT - Available in 2700K, 3000K, 3500K, and 4000K, tolerance within a 3-step MacAdam ellipse. My White Tunable White (TW) 2700K- 6500K available - consult factory. CRI - Minimum 90. All Drivers - High efficient, constant current, soft start, Electronic Class 2 with a PFC>0.90. For more detailed information on the available drivers, please see page 6. Sensors - Selux offers a variety of integral sensor options. For details and specifications, please see page 8. Thermal Performance: Ambient Operating Temperature - Luminaires are suitable for Maximum ambient temperature of 35 C (95 F) for all drivers. Luminaires are suitable for minimum ambient temperatures of: -40ºC (-40ºF) for DIM, DIL, DM, DML, and DED drivers. -20ºC (-4ºF) for SR drivers. 0ºC (32ºF) for DC2, DCE, and DC5 drivers. Luminaire Finish: Powder Coat - All Selux luminaries are finished in high quality polyester powder coating in our Tiger Drylac certified facility and are tested in accordance with test specifications for coatings from ASTM and PCI. All products undergo a five stage intensive pretreatment process where product is thoroughly cleaned, phosphated, and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultra violet resistance for color retention. Standard colors for Piix MRC are White (WH), Black (BK), Semi-Matte Black (BL), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide. Warranty: 5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the Piix MRC luminaire shall be free from defects in material and workmanship for up to five (5) years from date of shipment. This limited warranty covers the LED driver and LED light engine when installed according to Selux instructions and operated within the Ambient Temperature. For additional details and exclusions, see Selux Terms and Condition of Sale. Certifications and Compliance: NRTL - For dry and damp locations (i.e. culus, ccsaus) ARRA Compliant ADA Compliant RoHS Compliant Page 2 of 2
Cable Mounting (C) Top "A" Cable Mounting (C) Feed "B" "C" "B" 48" Max. Side "D" Feed Bottom Nominal Length A Housing Length "A" Cable Mounting (C) - Dimensions * B (Ref.) Typical Mounting Distance for Normal Installation C Mid. Suspension D Feed Location Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM 02 (2 ft.) 2' - 0 5/6" 67 0' - 2 /8" 54 ' - 8 /6" 509 0' - /8" 29 03 (3 ft.) 3' - 0 5/6" 922 0' - 3 /8" 79 2' - 6 /6" 763 0' - 2 /8" 54 04 (4 ft.) 4' - 0 5/6" 227 0' - 3 /8" 79 3' - 6 /6" 068 0' - 2 /8" 54. Ø 3/64 Aircraft Cable with chrome gripper for easy adjustment (48 max. from ceiling to luminaire). 05 (5 ft.) 5' - 0 5/6" 53 0' - 3 /8" 79 4' - 6 /6" 373 0' - 2 /8" 54 06 (6 ft.) 6' - 0 5/6" 836 0' - 3 /8" 79 5' - 6 /6" 677 0' - 2 /8" 54 07 (7 ft.) 7' - 0 5/6" 24 0' - 3 /8" 79 6' - 6 /6" 982 0' - 2 /8" 54 08 (8 ft.) 8' - 0 5/6" 2446 0' - 3 /8" 79 7' - 6 /6" 2287 0' - 2 /8" 54 *Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance. PIIX Cable (C) suspension detail (Feed location(s) only) PIIX Cable (C) suspension detail PXLDI (Feed Cable(C) location(s) Suspension only) Detail (Feed location(s) only) Outlet box for feed only (by others) Cross bar with /4-20 rod and ground screw 2x Outlet box screws (by others) /4 x 5 diameter canopy (white) Cord strain relief bushing /4-20 chrome coupler 2x White cable stay Feed cord (white) Chrome gripper Min. 5/8 to Max. 3/4 PIIX Cable (C) suspension detail PXLDI Cable (C) Suspension (Non-Feed Detail location(s) only) (Non-Feed location(s) only) PIIX Cable (C) suspension detail Ceiling (Non-Feed location(s) only) Ceiling /4-20 Threaded Rod (supplied & installed in the field by others) /4 x 2 diameter Canopy (white) /4-20 Slip ring coupler 3/64 Aircraft cable Chrome gripper 3/64 Aircraft cable Luminaire Luminaire Page 3 of 2
Stem Mounting (S & RS) Top Stem Mounting (S & RS) 2 "B" Feed "C" "B" 48" Side "D" Feed Bottom "A". Ø 5/8 Swivel Stem provides 30 swivel and can be cut in field (48 max. from ceiling to luminaire). 2. Ø 5/8 Rigid Stem is fixed and is not able to be cut/adjusted in field (48 max. from ceiling to luminaire). Nominal Length Swivel (S) & Rigid Stem (RS) Mountings - Dimensions A Housing Length * B (Ref.) End Suspensions C Mid. Suspension D Feed Location Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM 02 (2 ft.) 2' - 0 5/6" 67 0' - 0 7/8" 22 ' - 0 9/6" 573 0' - 0 7/8" 22 03 (3 ft.) 3' - 0 5/6" 922 0' - 0 7/8" 22 2' - 0 9/6" 877 0' - 0 7/8" 22 04 (4 ft.) 4' - 0 5/6" 227 0' - 0 7/8" 22 3' - 0 9/6" 82 0' - 0 7/8" 22 05 (5 ft.) 5' - 0 5/6" 53 0' - 0 7/8" 22 4' - 0 9/6" 487 0' - 0 7/8" 22 06 (6 ft.) 6' - 0 5/6" 836 0' - 0 7/8" 22 5' - 0 9/6" 792 0' - 0 7/8" 22 07 (7 ft.) 7' - 0 5/6" 24 0' - 0 7/8" 22 6' - 0 9/6" 2097 0' - 0 7/8" 22 08 (8 ft.) 8' - 0 5/6" 2446 0' - 0 7/8" 22 7' - 0 9/6" 240 0' - 0 7/8" 22 *Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance. PXLDI Swivel Stem (S) Suspension Detail (feed wires through stem supplied by Selux) PXLDI Rigid Stem (RS) Suspension Detail (feed wires through stem supplied by Selux) Outlet box (supplied & installed by others) Hemispherical assembly Cotter pin /4 IP Swivel crossbar with ground screw 3/4 x 5 diameter canopy (white) /4 IP steel swivel stem (white) 3/8 Male x /4 Male hex bushing Luminaire Outlet box (supplied & installed by others) /4 IP Crossbar with ground screw /4 IP Hex nut /4 x 5 diameter canopy (white) Canopy securing screw (white) /4 IP Steel rigid stem (white) 3/8 Male x /4 Male hex bushing Luminaire Page 4 of 2
Wall Mounting (W) "B" "C" "B" Top "D" Feed Bottom "A" Nominal Length "A" Housing Length Wall (W) - Dimensions * "B" (Ref.) End Suspensions "C" Mid. Suspension "D" Feed Location Feet/Inch mm Feet/Inch mm Feet/Inch mm Feet/Inch mm 02 (2 ft.) 2' - 0 5/6" 67 0' - 3 /8" 79 ' - 6 /6" 458 0' - 3 /8" 79 03 (3 ft.) 3' - 0 5/6" 922 0' - 6 /8" 56 2' - 0 /6" 6 0' - 6 /8" 56 04 (4 ft.) 4' - 0 5/6" 227 0' - 6 /8" 56 3' - 0 /6" 95 0' - 6 /8" 56 05 (5 ft.) 5' - 0 5/6" 53 0' - 6 /8" 56 4' - 0 /6" 220 0' - 6 /8" 56 06 (6 ft.) 6' - 0 5/6" 836 0' - 6 /8" 56 5' - 0 /6" 525 0' - 6 /8" 56 07 (7 ft.) 7' - 0 5/6" 24 0' - 6 /8" 56 6' - 0 /6" 830 0' - 6 /8" 56 08 (8 ft.) 8' - 0 5/6" 2446 0' - 6 /8" 56 7' - 0 /6" 235 0' - 6 /8" 56 *Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance. Wall Mount (W) (Covers a 4x4 J-Box only) 2 3 4" [02mm] 4 (02mm) 4" [02mm] 4 (02mm) 3 3 3 3 /8 " (85mm) [25mm]. Aluminum wall bracket (by selux) 2. 4"x4" J-Box at feed location (supplied and installed by others). 3. /4-20 Threaded rod, /4-20 lock washer & /4-20 nut required to anchor the wall bracket Mounting hardware supplied and installed to code by others. 3 3/8" 3 3 [85mm] /8 (85mm) Page 5 of 2
Drivers: 0-0V linear dimming (DIM) Luminaires supplied with drivers offering the capability of either normal switched operation or 0-0V dimming for linear dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to %. 0-0V logarithmic dimming (DIL) Luminaires supplied with drivers offering the capability of either normal switched operation or 0-0V dimming for logarithmic dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to %. eldoled SOLOdrive 0-0V linear dimming (DM) Luminaires supplied with SOLOdrive 0-0V dimming driver for linear dimming curve. Minimum dimming level preset at factory to %. For dim to dark (down to 0.%), please consult factory. eldoled SOLOdrive 0-0V logarithmic dimming (DML) Luminaires supplied with SOLOdrive 0-0V dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to %. For dim to dark (down to 0.%), please consult factory. eldoled ECOdrive DALI dimming (DED) Luminaires supplied with ECOdrive DALI dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to %. For dim to dark (down to 0.%), please consult factory. * For control recommendations for eldoled drivers, please consult eldoled. LUTRON 2-wire dimming (DC2) Luminaires supplied with Hi-Lume 2-wire dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to %. LUTRON Ecosystem dimming (DCE)/(DC5) Luminaires supplied with Hi-Lume EcoSystem (4 wire, digital link) dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to % (DCE) or 5% (DC5). * For control recommendations and system layout for Lutron drivers, please contact Lutron. * Driver Quantity (Based on B45 light engine) Fixture Length Dimming Protocol 2 ft. 3 ft. 4 ft. 5 ft. 6 ft. 7 ft. 8 ft. RUN Philips Xitanium Sensor Ready DALI dimming (SR) Luminaires supplied with Xitanium SR dimming driver programmed for Constant Current Reduction (CCR). Minimum dimming level down to 5%. For use with E and P sensors only. DIM, DIL, DC2, DCE, DC5, SR 2 2 4 4 4 4 DM, DML, DMD, DED 2 3 4 4 4 Approximately drive per 4 ft. Approximately drivers per 4 ft. *For inrush and control current, please refer to the driver manufacturers spec sheets. * For B48 light engine, pleases consult factory. Wiring Diagrams Sensor Wiring Diagrams 0-0V linear (DIM) 0-0V logarithmic (DIL) 0-0V linear eldoled SOLOdrive (DM) 0-0V logarithmic eldoled SOLOdrive (DML) DALI eldoled ECOdrive (DED) Philips SR DALI (SR) DIM, DIL, DM, DML, DED & SR DALI DALI standard ENLIGHTED OR PHILIPS SENSOR DCE, DC5 SR (+) SR (-) PHILIPS SR Lutron EcoSystem (DCE) Lutron EcoSystem (DC5) SENSOR SWITCH ELDO 0-0V (+) (-) 0-0V AUX (+) AUX (-) Page 6 of 2
Fuse (FS) - Fusing, luminaires supplied with a in-line fuse located on the hot wire for each feed. (supplied with an 8A slow burn fuse). Separate Switching (SS) - Luminaires available with separately switched 4 (nominal) sections starting at 7 and up. Luminaire is intended to be wired to the same panel/breaker (not intended for Emergency use). - To specify this option, the number of separately switched sections an locations of these sections must be provided at time of order. * If the project requires different separate switching than outlined above please consult the factory. *For Separate Switching with sensors, please consult factory. EM (Emergency Battery Pack)* - Emergency battery pack is available starting at the 4 nominal length and up in 2 nominal sections. The battery pack is housed within the fixture. - For individual luminaires, the lit section will be located on the feed end of the fixture. If a different location is needed please consult the factory. - For Runs, please specify location of lit section (in 2 nominal sections). * For EM with sensors, please consult factory. Emergency Circuit (EC) - Luminaires with EC option compliant to UL 924 listed emergency luminaire. EC luminaires are intended to be wired to separate panels/breakers for emergency use. - For 2 to 6 nominal luminaires, the entire fixture is wired for operation on emergency circuit. - For 7 and up nominal luminaires, the first 4 nominal length is wired for operation by a separate EM circuit by default to meet the required Life Safety Code (NFPA 0). * If a different configuration is needed please consult the factory. * For EC with sensors, please consult factory. Emergency Battery Pack (EM) EM Model # Input Operation Time Lumen Output ILB-SL-CP2 3.7W Max. 90 Minutes 200 lm Joiner System - standard for Runs and Configurations M3x5 pan head phillips screw *Recommended phillips #2 screw driver* Joiner Extrusion *pre-installed at factory* M4x30 socket head screw *Recommended M4 hex key* Fixture Extrusion Fixture Extrusion Page 7 of 2
Sensor Ordering Chart Quantity Sensor Settings * x Number of Sensors E Enlighted FS-D22 P Philips Easy Sense SNS02 S Sensor Switch MSD EZ Daylight 2 Occupancy/Vacancy 3 Daylight/Occupancy/Vacancy * Settings not available with Enlighted Enlighted FS-D22 (E) Occupancy/vacancy, daylight harvesting, plus the Internet of Things (IoT) data collection and reporting. For full details, please see FS-D22 spec sheet on the Enlighted website. Must be paired with Philips Xitanium SR driver (SR driver selection). Commissioning by Enlighted. *Please contact Enlighted for complete details prior to specifying. *Sensor can control up to 4 drivers. Please refer to driver quantity chart on page 6. Multiple sensors may be required for longer lengths. Philips EasySense SNS02 (P) Occupancy/vacancy and daylight harvesting. Sensor can be programmed on-site via NFC or IR using Android app only, by others. For full details, please see the SNS02 spec sheet on the Philips website. Must be paired with Philips Xitanium SR driver (SR driver selection). Wall dimming via wireless wall switch from Philips/Illumra (www.illumra.com/easysense). **Please contact Philips for complete details prior to specifying. *Sensor can control up to 0 drivers. Please refer to driver quantity chart on page 6. Multiple sensors may be required for longer lengths. Sensor Switch MSD EZ (S) Occupancy/vacancy and daylight harvesting. For full functionality and programming options, select settings option 3. If a different settings option is selected, other settings may be unavailable. For full details, please see MSD EZ spec sheets on the Sensor Switch website. Must be paired with eldoled 0-0V driver (DIM driver selection). Manual control of dimming not available with MSD EZ sensor. *Please contact Sensor Switch for complete details prior to specifying. *Sensor can control up to 30 drivers. Please refer to driver quantity chart on page 6. Multiple sensors may be required for longer lengths. Occupancy Vacancy Daylight Harvesting Driver Compatibility Enlighted FS-D22 (E) See Enlighted s website for full capabilities SR Philips EasySense SNS02 (P) SR Sensor Switch MSD EZ (S) DIM Factory Presets - Sensors come from the sensor manufacturer with factory presets for each of the settings in above chart. Please see sensor manufacturers spec sheets for details on presets and re-programming. Commissioning - Commissioning of sensors and installation by others. Contact sensor manufacturer for details and costs associated with commissioning the system prior to specification of sensors. Standard Sensor Placement - for other placement options, please consult factory. For functionality and limitations, please see sensor details above. Qty Sensor - Beginning Qty 2 Sensor - Beginning and End (9 fixtures and longer) Fixture Length Lit Section* 3 (76mm) Qty 3+ Sensor - For spacing between sensors, please consult the sensor manufacturer. 2 3 /8 (60mm) Beginning of Run Notes:. For spacing between sensors, please consult the sensor manufacturer. 2. Exact sensor placement and coverage will be defined by approved factory drawing. 3. Sections controlled by sensors may not be symmetrical - consult factory for layout. Faceplate Aluminum Sensor Plate -to be painted same as fixture unless specified otherwise * Lit section will be the fixture length minus 3 for sensor plate. Page 8 of 2
Standard Direct/Indirect (PXLDI) shapes/configurations: Listed below are the minimum lengths and details for standard shapes. These standard shapes can be combined with each other and/or the standard luminaire lengths, ensuring full even illumination. If you have any questions, please consult the factory. The minimum standard lengths for T & X shapes: - IT90 = 2 nominal on the short leg and 4 nominal on the long side - IX90 = 4 nominal for either direction *IT90 and IX90 direct corners are lit with an MRC in the corner. The minimum standard lengths for L shapes: - IL90 or V90 open shapes is 2 x 2 nominal (example: leg, 90, leg) - IL90 or V90 closed shapes is 4 x 4 nominal (example: 90, leg, 90) - L90 & V90 corners can be joined directly together to provide a 4 x 4 nominal shape. *IL90 corners are not lit. *For sensors in configurations, please consult factory. Project Specific Direct/Indirect shapes/configurations: Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements. Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review. IT90 - Lit "T" section "C" Housing "C2" Ref. "C" Ref. IX90 - Lit "X" section "E" Housing "E" Ref. "E2" Ref. "B" Housing "B" Ref. IL90 - Lit Horizontal corner "D" Ref. "B" Housing "F2" Ref. "B" Ref. "A" Housing "A" Housing See note Indirect side Top view "A" Housing "A" Housing "D" Housing "D2" Ref. "B" Housing See note Indirect side Top view "F" Housing "F" Ref. "B" Ref. Indirect side Top view See note 3 5 /6 (00mm) Note: The Indirect side of the shapes have small unlit sections for certain mounting types. Direct side Bottom view "A" Housing "A" Housing "A" Housing "A" Housing "D" Housing "D2" Ref. "D" Ref. "B" Housing "B" Housing Direct side Bottom view "F" Housing "F2" Ref. "F" Ref. "B" Ref. "B" Ref. Direct side Bottom view 2 /4 (58mm) 2 3 /8 (60mm) "C" Ref. "C2" Ref. "C" Housing "B" Housing "B" Ref. "E" Ref. "E2" Ref. "E" Housing Page 9 of 2
Standard Direct/Indirect (PXLDI) shapes/configurations: Direct/Indirect PXLDI Corner and Section - Dimensions IL90 IT90 IX90 Nominal Length Feet/Inch MM Feet/Inch MM Feet/Inch MM "A" Housing (Outside) 2' - 2 3/6" 666 N/A N/A N/A N/A "A" Housing (Inside) ' - 3/6" 606 N/A N/A N/A N/A "B" Housing N/A N/A ' - 9 3/6" 555 ' - 3/6" 606 * "B" Ref. N/A N/A ' - 3/6" 606 ' - 3/6" 606 "C" Housing N/A N/A 2' - 2 3/6" 666 N/A N/A * "C" Ref. N/A N/A ' - 3/6" 606 ' - 9 3/6" 555 * "C2" Ref. N/A N/A 2' - " 636 N/A N/A "D" Housing N/A N/A 4' - 0 /6" 220 N/A N/A * "D" Ref. N/A N/A ' - " 585 N/A N/A * "D2" Ref. N/A N/A 2' - " 636 N/A N/A "E" Housing N/A N/A N/A N/A 4' - 0 /6" 220 * "E" Ref. N/A N/A N/A N/A ' - " 585 * "E2" Ref. N/A N/A N/A N/A 2' - " 636 "F" Housing N/A N/A N/A N/A 4' - 2 /6" 27 * "F" Ref. N/A N/A N/A N/A 2' - " 636 * "F" Ref. N/A N/A N/A N/A 2' - " 636 * Dimension(s) rounded to the nearest /6 (mm) tolerance. Page 0 of 2
Photometry 20 Optics / 8W LED / 4000K CCT 844 63 4207 204 Catalog #: PXLDI-B45-B35-40-20-ID-XX-04-XX-UNV Report #: 2472594.08 & 2472594.0 Delievered Lumens: 7884 Input Watts: 80.8W Efficacy: 97.6 Power Factor: 0.990 Total Harmonic Distortion: 0.8 CCT: 3962K CRI: 93.8 Max Candela: 844 @.5 from Vertical 2 Maximum Candela = 844 Located At Horizontal Angle = 0, Vertical Angle =.5 # - Vertical Plane Through Horizontal Angles (90-270) # 2 - Vertical Plane Through Horizontal Angles (0-80) 35 Optics / 8W LED / 4000K CCT 454 36 2077 039 Catalog #: PXLDI-B45-B35-40-35-ID-XX-04-XX-UNV Report #: 2472594.08 & 2472594.02 Delivered Lumens: 8536 Input Watts: 80.8W Efficacy: 06 Power Factor: 0.99 Total Harmonic Distortion: 0.8 CCT: 3962K CRI: 93.8 Max Candela: 454 @ 26.5 from Vertical 2 Maximum Candela = 454 Located At Horizontal Angle = 45, Vertical Angle = 26.5 # - Vertical Plane Through Horizontal Angles (90-270) # 2 - Vertical Plane Through Horizontal Angles (0-80) 50 Optics / 8W LED /4000K CCT 32 2334 556 778 Catalog #: PXLDI-B45-B35-40-50-ID-XX-04-XX-UNV Report #: 2472594.08 & 2472594.04 Delivered Lumens: 8760 Input Watts: 80.8W Efficacy: 08 Power Factor:.990 Total Harmonic Distortion: 0.8 CCT: 3962K CRI: 93.8 Max Candela: 32 @.5 from Vertical 2 Maximum Candela = 32 Located At Horizontal Angle = 0, Vertical Angle =.5 # - Vertical Plane Through Horizontal Angles (90-270) # 2 - Vertical Plane Through Horizontal Angles (0-80) Page of 2
Photometry Piix LED Direct/Indirect Photometry Multiplier Table CCT Multiplier.000 0.93 4000K 3500K 3000K 0.903 2700K 0.903 Page 2 of 2